Use the 2nd BAR for the oxsemi_840 chip as BAR for base_hi. Tested with:
Parallel controller [0701]: Oxford Semiconductor Ltd VScom 011H-EP1
1 port parallel adaptor [1415:8403] (prog-if 03 [IEEE1284])
This patch is needed to make 'TRISTATE' work with that adaptor.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wrap PNP probe code in #ifdef CONFIG_PNP. We already do the same for
CONFIG_PCI.
Without this change, we'll have unresolved references to pnp_get_resource()
function when CONFIG_PNP=n. (This is a new interface that's not in mainline
yet.)
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit f63fd7e299 ("parport_pc: detection
for SuperIO IT87XX POST") only released the IO port region on success,
not when the probe for the IT87XX chip failed.
That caused not only a reserved region to leak, but also caused an oops
when the driver module was unloaded and somebody tried to cat
/proc/ioports - because the string that was assigned to the IO port
region was a static string in the module virtual address area.
Reported-by: Lubos Lunak <l.lunak@suse.cz>
Cc: Jan Kara <jack@suse.cz>
Cc: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix section warning for parport_ECP_supported(); it's called from a routine
exported to modules, so it can't be removed with __devinit section pruning.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add detection for IT87XX SuperIO chip and disabling its POST feature, which
made noise on parallel port's pins.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Added pci device id for the Quatech SPPXP-100 ExpressCard - 0x278 - to
include/linux/pci_id.h
Modified drivers/parport/parport_pc.c to support the Quatech SPPXP-100 Parallel port PCI ExpressCard
[akpm@linux-foundation.org: build fix]
Signed-off-by: Luís P Mendes <luis.p.mendes@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several arches used the exact same code for their parport irq handling.
Make that code generic, in parport_irq_handler().
Also, s/__inline__/inline/ in include/linux/parport.h.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
http://bugzilla.kernel.org/show_bug.cgi?id=8821 reports a might_sleep()
warning due to parport_pc_exit() running platform_device_unregister() while
holding ports_lock.
Just remove the locking: nobody else can access ports_list during module_exit.
Cc: "Mike Sharkey" <mike@pikeaero.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The IO port range requested by parport_pc.c:sio_ite_8872_probe is too small.
The IO-ports of ttyS1 (0x2f8) will be missconfigured by the ITE-chip. The ITE
starts looking for the chip a 0x2a0. An IO-portrange of 32 will not overwrite
the ports of ttyS1. Therefore register 0x60 should be written with
0xe5000000, enabling the ITE and setting IO-portsize to 32 bytes.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alpha:
drivers/parport/parport_pc.c: In function 'parport_pc_fifo_write_block_dma':
drivers/parport/parport_pc.c:636: warning: implicit declaration of function 'dma_map_single'
drivers/parport/parport_pc.c:637: error: 'DMA_TO_DEVICE' undeclared (first use in this function)
drivers/parport/parport_pc.c:637: error: (Each undeclared identifier is reported only once
drivers/parport/parport_pc.c:637: error: for each function it appears in.)
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Give legacy parallel ports a platform device in the device tree.
This is a quick and dirty implementation; it doesn't actually convert the
legacy parport code to the device driver model (by splitting out probing from
device creation). But at least parallel port device drivers will finally have
a device to work with.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently a parport_driver can't get a handle on the device node for the
underlying parport (PNPACPI, PCI, etc). That prevents correct placement of
sysfs child nodes, which can affect things like power management.
This patch adds a field to "struct parport" pointing to that device node, and
updates non-legacy port drivers to initialize that device pointer. That field
replaces the analagous PCI-only support in parport_pc.
[akpm@linux-foundation.org: fix powerpc build]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference
to .init.text: from .text between 'parport_pc_probe_port' (at offset
0x14f7) and 'parport_pc_unregister_port'
parport_dma_probe() cannot be declared __devinit as it is called
from parport_pc_probe_port() which isn't.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When CONFIG_HOTPLUG=n, parport_pc calls some __devinit == __init code that
could be discarded. These calls are made from parport_irq_probe(), which is
called from parport_pc_probe_port(), which is an exported symbol, so the calls
could (possibly) happen after init time.
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.text: from .text between 'parport_irq_probe' (at offset 0x31d) and 'parport_pc_probe_port'
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.text: from .text between 'parport_irq_probe' (at offset 0x346) and 'parport_pc_probe_port'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the parallel port (implemented as separate PCI function) on
the Oxford Semiconductor OX16PCI952.
Signed-off-by: Ryan Underwood <nemesis@icequake.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
The last change for partport_pc did fix the common case for all PowerMacs,
but it broke the case for PCI multiport IO cards. In fact, the config
option CONFIG_PARPORT_PC_SUPERIO=y lead to a hard crash when cups probed
the parport driver. It enables the winbond and smsc probing.
Remove the PARPORT_BASE check again, parport_pc_find_nonpci_ports() will
take care of it. All powerpc configs should have
CONFIG_PARPORT_PC_SUPERIO=n, the code did not find anything on the chrp
boards we tested it on.
Tested on a G4/466 with a PCI card:
0001:10:13.0 Serial controller: Timedia Technology Co Ltd PCI2S550 (Dual 16550 UART) (rev 01) (prog-if 02 [16550])
Subsystem: Timedia Technology Co Ltd Unknown device 5079
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 53
Region 0: I/O ports at f2000800 [size=32]
Region 2: I/O ports at f2000870 [size=8]
Region 3: I/O ports at f2000860 [size=8]
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ppc can boot one single binary on prep, chrp and pmac boards. ppc64 can
boot one single binary on pseries and G5 boards. pmac has no legacy io,
probing for PC style legacy hardware (or accessing the legacy io area
regulary) may lead to a hard crash:
* add check for parport_pc, exit on pmac. 32bit chrp has no
->check_legacy_ioport, the probe is always called. 64bit chrp has
check_legacy_ioport, check for a "parallel" node
* add check for isapnp, only PReP boards may have real ISA slots. 32bit
PReP will have no ->check_legacy_ioport, the probe is always called.
* update code in i8042_platform_init. Run ->check_legacy_ioport first,
always call request_region. No functional change. Remove whitespace
before i8042_reset init.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Randy Dunlap <rdunlap@xenotime.net>
Fix all modpost section mismatch warnings in parport_pc:
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.text: from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x230)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.text: from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x283)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.text: from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x3e6)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.text: from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x400)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.text: from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x463)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.text: from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x488)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.data:superios from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x54c)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.data: from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x56a)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.data: from .text.parport_pc_pci_probe after 'parport_pc_pci_probe' (at offset 0x67)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.data: from .text.parport_pc_pci_probe after 'parport_pc_pci_probe' (at offset 0x9f)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.data: from .text.parport_pc_pci_probe after 'parport_pc_pci_probe' (at offset 0xa7)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.data:cards from .text.parport_pc_pci_probe after 'parport_pc_pci_probe' (at offset 0x132)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.data: from .text.parport_pc_pci_probe after 'parport_pc_pci_probe' (at offset 0x142)
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the assumption that pnp_register_driver() returns the number of devices
claimed.
parport_pc_init() does nothing with "count", so remove it. Then nobody uses
the return value of parport_pc_find_ports(), so make it void. Finally, update
pnp_register_driver() usage.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
free_dma() isn't implemented on ARM unless HAS_DMA is set.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Trivial "const" additions to places in parport that truly are const.
Signed-off-by: Marko Kohtala <marko.kohtala@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use schedule_timeout_interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size. Also use
human-time to jiffies units conversion functions rather than direct HZ
division to avoid rounding issues.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This interface is said to be commonly used in germany: "The patch has been
proven to work fine in a beige G3 Mac."
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=262324
Signed-off-by: maximilian attems <janitor@sternwelten.at>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The dynamic pci id logic has been bothering me for a while, and now that
I started to look into how to move some of this to the driver core, I
thought it was time to clean it all up.
It ends up making the code smaller, and easier to follow, and fixes a
few bugs at the same time (dynamic ids were not being matched
everywhere, and so could be missed on some call paths for new devices,
semaphore not needed to be grabbed when adding a new id and calling the
driver core, etc.)
I also renamed the function pci_match_device() to pci_match_id() as
that's what it really does.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
kernel 2.6.12-rc2 adopted some code by Bjorn Helgaas supporting NetMos combo
controller cards. this implementation doesn't work for nm9855 based cards!
there are two reasons:
a) the module 'parport_pc' doesn't want to give the resonsibility for
the netmos_9855 to 'parport_serial' and can not handle the serial lines
-- trivial to fix...
http://lists.infradead.org/pipermail/linux-parport/2005-February/000250.htmlhttp://lkml.org/lkml/2005/3/24/199 b) the support for the nm9855 in
'parport_serial' still doesn't work because of wrong assumptions about
the relevant BARs port address layout for this chip:
0000:00:09.0 Communication controller:
NetMos Technology PCI 9855
Multi-I/O Controller (rev 01)
(= 9710:9855)
Subsystem: LSI Logic / Symbios Logic 1P4S (= 1000:0014)
Flags: medium devsel, IRQ 177
I/O ports at a800 [size=8] (= parport)
I/O ports at a400 [size=8]
I/O ports at a000 [size=8] (= serial)
I/O ports at 9800 [size=8] (= serial)
I/O ports at 9400 [size=8] (= serial)
I/O ports at 9000 [size=16] (= serial)
the following patch will fix the problem.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Part of parport_pc that uses ISA DMA helpers made conditional on
CONFIG_ISA_DMA_API. As the result, driver got usable for boxen that do
not have ISA DMA stuff and have normal PCI parport card stuck into
them - these never use DMA anyway.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Bernhard Walle