By adding a card state that records if it is suspended or resumed, we
can accept asyncronus suspend/resume requests for the mmc and sd
bus_ops.
MMC_CAP_AGGRESSIVE_PM, will at request inactivity through the runtime
bus_ops callbacks, execute a suspend of the the card. In the state were
this has been done, we can receive a suspend request for the mmc bus,
which for sd and mmc forced the card to active state by a
pm_runtime_get_sync. In other words, the card was resumed and then
immediately suspended again, completely unnecessary.
Since the suspend/resume bus_ops callbacks for sd and mmc are now
capable of handling asynchronous requests, we no longer need to force
the card to active state before executing suspend. Evidently preventing
the above sequence for MMC_CAP_AGGRESSIVE_PM.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
A previous commit (fdfa20c163) reordered the shutdown sequence
in mmc_blk_remove_req. However, mmc_cleanup_queue is now called before
we get the card pointer, and mmc_cleanup_queue sets mq->card to NULL.
This patch moves the card pointer assignment before mmc_cleanup_queue.
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Current MMC driver doesn't handle generic error (bit19 of device
status) in write sequence. As a result, write data gets lost when
generic error occurs. For example, a generic error when updating a
filesystem management information causes a loss of write data and
corrupts the filesystem. In the worst case, the system will never
boot.
This patch includes the following functionality:
1. To enable error checking for the response of CMD12 and CMD13
in write command sequence
2. To retry write sequence when a generic error occurs
Messages are added for v2 to show what occurs.
Signed-off-by: KOBAYASHI Yoshitake <yoshitake.kobayashi@toshiba.co.jp>
Signed-off-by: Chris Ball <cjb@laptop.org>
Considering shutdown of the card, the responsibility to initate this
sequence shall be driven from the mmc_bus.
This patch enables the mmc_bus to handle this sequence properly. A new
.shutdown callback is added in the mmc_driver struct which is used to
shutdown the blk device.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Inside the routine mmc_blk_ioctl_cmd() the sanitize command is
identified according to the value of bits 16-23 of the argument.
but what happens if a different command is sent, and only by
chance, bits 16-23 contain the value of SANITIZE command ?
In that case a SANITIZE command will be falsely identified.
In order to prevent such a case, the condition is expanded and
now it also checks the opcode itself, and verifies that it is an
MMC_SWITCH opcode.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We had a multi-partition SD-Card with two ext2 file systems. The partition
table was getting overwritten by a race between the card removal and
the unmount of the 2nd ext2 partition.
What was observed:
1. Suspend/resume would call to remove the device. The clearing
of the device information is done asynchronously.
2. A request is made to unmount the file system (this is called
after the removal has started).
3. The remapping table was cleared by the asynchronous part of
the device removal.
4. A write request to the super block (block 0 of the partition)
was sent down and instead of being remapped to the partition
offset, it was remapped to block 0 of the device which is where
the partition table is located.
5. Write was queued and written resulting in the overwriting
of the partition table with the ext2 super block.
6. The mmc_queue is cleaned up.
The mmc card device driver used to access SD cards, was calling del_gendisk
before calling mmc_cleanup-queue. The comment in the mmc_blk_remove_req
code indicated that it expected del_gendisk to block all further requests
from being queued but it doesn't. The mmc driver uses the presences of the
mmc_queue to determine if the request should be queued.
The fix was to clean up the mmc_queue before the rest of the
the delete partition code is called.
This prevents the overwriting of the partition table.
However, the umount gets an error trying to write the super block.
The umount should be issued before the device is removed but that
is not always possible. The umount is still needed to cleanup other
data structures.
Addresses the problem described in http://crbug.com/240815
Signed-off-by: Paul Taysom <taysom@chromium.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Once the mmc blkdevice is being probed, runtime pm will be enabled.
By using runtime autosuspend, the power save operations can be done
when request inactivity occurs for a certain time. Right now the
selected timeout value is set to 3 s. Obviously this value will likely
need to be configurable somehow since it needs to be trimmed depending
on the power save algorithm.
For SD-combo cards, we are still leaving the enablement of runtime PM
to the SDIO init sequence since it depends on the capabilities of the
SDIO func driver.
Moreover, when the blk device is being suspended, we make sure the device
will be runtime resumed. The reason for doing this is that we want the
host suspend sequence to be unaware of any runtime power save operations
done for the card in this phase. Thus it can just handle the suspend as
the card is fully powered from a runtime perspective.
Finally, this patch prepares to make it possible to move BKOPS handling
into the runtime callbacks for the mmc bus_ops. Thus IDLE BKOPS can be
accomplished.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The sanitize support is added as a user-app ioctl call, and
was removed from the block-device request, since its purpose is
to be invoked not via File-System but by a user.
This feature deletes the unmap memory region of the eMMC card,
by writing to a specific register in the EXT_CSD.
unmap region is the memory region that was previously deleted
(by erase, trim or discard operation).
In order to avoid timeout when sanitizing large-scale cards,
the timeout for sanitize operation is 240 seconds.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The value passed is 0 in all but "it can never happen" cases (and those
only in a couple of drivers) *and* it would've been lost on the way
out anyway, even if something tried to pass something meaningful.
Just don't bother.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
For normal request mmc_blk_issue_rq is called twice with asynchronous
transfer(cur and prev). Host's claim and release can be done in each
mmc_blk_issue_rq. However, Special request is currently excluded in
asynchronous transfer. After special request is finished, if there is
no new request, mmc_release_host won't be called in mmc_blk_issue_rq.
The problem is founded during mmc_suspend.
[<c0541124>] (__schedule+0x0/0x78c) from [<c05419e8>] (schedule+0x38/0x78)
[<c05419b0>] (schedule+0x0/0x78) from [<c03a843c>] (__mmc_claim_host+0xac/0x1b4)
[<c03a8390>] (__mmc_claim_host+0x0/0x1b4) from [<c03ac98c>] (mmc_suspend+0x28/0x9c)
[<c03ac964>] (mmc_suspend+0x0/0x9c) from [<c03aad24>] (mmc_suspend_host+0xb4/0x194)
...
Reported-by: Johan Rudholm <jrudholm@gmail.com>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch supports packed write command of eMMC4.5 devices. Several
writes can be grouped in packed command and all data of the individual
commands can be sent in a single transfer on the bus. Large amounts of
data in one transfer rather than several data of small size are
effective for eMMC write internally. As a result, packed command help
write throughput be improved. The following tables show the results
of packed write.
Type A:
test none | packed
iozone 25.8 | 31
tiotest 27.6 | 31.2
lmdd 31.2 | 35.4
Type B:
test none | packed
iozone 44.1 | 51.1
tiotest 47.9 | 52.5
lmdd 51.6 | 59.2
Type C:
test none | packed
iozone 19.5 | 32
tiotest 19.9 | 34.5
lmdd 22.8 | 40.7
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
It's not necessary to start a new request while error handling if
the card was removed.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When current request is running on the bus and if next request fetched
by mmcqd is NULL, mmc context (mmcqd thread) gets blocked until the
current request completes. This means that if new request comes in while
the mmcqd thread is blocked, this new request can not be prepared in
parallel to current ongoing request. This may result in delaying the new
request execution and increase it's latency.
This change allows to wake up the MMC thread on new request arrival.
Now once the MMC thread is woken up, a new request can be fetched and
prepared in parallel to the current running request which means this new
request can be started immediately after the current running request
completes.
With this change read throughput is improved by 16%.
Signed-off-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Reviewed-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
RPMB partition is accessing though /dev/block/mmcXrpmb device
User callers can read and write entire data frame(s) as defined
by JEDEC Standard JESD84-A441, using standard IOCTL interface.
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Do not scan rpmb partitions for "soft" partitions, since the rpmb
partition contains protected data. Silences the following message
during boot:
mmcblkXRPMB: unknown partition table
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are infinite loops in the mmc code that can be caused by bad
hardware. The code will loop forever if the device never comes back
from program mode, R1_STATE_PRG, and it is not ready for data,
R1_READY_FOR_DATA.
A long timeout is added to prevent the code from looping forever.
The timeout will occur if the device never comes back from program
state or the device never becomes ready for data.
It's not clear whether the timeout will do more than log a pr_err()
and then start a fresh hang all over again. We may need to extend
this patch later to perform some kind of reset of the device (is
that possible?) or rejection of new I/O to the device.
Signed-off-by: Trey Ramsay <tramsay@linux.vnet.ibm.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For several MoviNAND eMMC parts, there are known issues with secure
erase and secure trim. For these specific MoviNAND devices, we skip
these operations.
Specifically, there is a bug in the eMMC firmware that causes
unrecoverable corruption when the MMC is erased with MMC_CAP_ERASE
enabled.
References:
http://forum.xda-developers.com/showthread.php?t=1644364https://plus.google.com/111398485184813224730/posts/21pTYfTsCkB#111398485184813224730/posts/21pTYfTsCkB
Signed-off-by: Ian Chen <ian.cy.chen@samsung.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable <stable@vger.kernel.org> [3.0+]
Signed-off-by: Chris Ball <cjb@laptop.org>
For completing any block request, MMC block driver is calling:
spin_lock_irq(queue)
__blk_end_request()
spin_unlock_irq(queue)
But if we analyze the sources of latency in kernel using ftrace,
__blk_end_request() function at times may take up to 6.5ms with
spinlock held and irq disabled.
__blk_end_request() calls couple of functions and ftrace output
shows that blk_update_bidi_request() function is almost taking 6ms.
There are 2 function to end the current request: ___blk_end_request()
and blk_end_request(). Both these functions do same thing except
that blk_end_request() function doesn't take up the spinlock
while calling the blk_update_bidi_request().
This patch replaces all __blk_end_request() calls with
blk_end_request() and __blk_end_request_all() calls with
blk_end_request_all().
Testing done: 20 process concurrent read/write on sd card
and eMMC. Ran this test for almost a day on multicore system
and no errors observed.
This change is not meant for improving MMC throughput; it's basically
about becoming fair to other threads/interrupts in the system. By
holding spin lock and interrupts disabled for longer duration, we
won't allow other threads/interrupts to run at all. Actually slight
performance degradation at file system level can be expected as we
are not holding the spin lock during blk_update_bidi_request() which
means our mmcqd thread may get preempted for other high priority
thread or any interrupt in the system.
These are performance numbers (100MB file write) with eMMC running
in DDR mode:
Without this patch:
Name of the Test Value Unit
LMDD Read Test 53.79 MBPS
LMDD Write Test 18.86 MBPS
IOZONE Read Test 51.65 MBPS
IOZONE Write Test 24.36 MBPS
With this patch:
Name of the Test Value Unit
LMDD Read Test 52.94 MBPS
LMDD Write Test 16.70 MBPS
IOZONE Read Test 52.08 MBPS
IOZONE Write Test 23.29 MBPS
Read numbers are fine. Write numbers are bit down (especially LMDD
write), may be because write requests normally have large transfer
size and which means there are chances that while mmcq is executing
blk_update_bidi_request(), it may get interrupted by interrupts or
other high priority thread.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If multi block write operation fails for SD card, during
error handling we send the SD_APP_SEND_NUM_WR_BLKS (ACMD22)
to know how many blocks were already programmed by card.
But mmc_sd_num_wr_blocks() function which sends the ACMD22
calculates the data timeout value from csd.tacc_ns and
csd.tacc_clks parameters which will be 0 for block addressed
(>2GB cards) SD card. This would result in timeout_ns and
timeout_clks being 0 in the mmc_request passed to host driver.
This means host controller would program its data timeout timer
value with 0 which could result in DATA TIMEOUT errors from
controller.
To fix this issue, mmc_sd_num_wr_blocks() should instead
just call the mmc_set_data_timeout() to calculate the
data timeout value. mmc_set_data_timeout() function
ensures that non zero timeout value is set even for
block addressed SD cards.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for large sector size of 4KB by disabling
emulation. This patch passes eMMC DATA_SECTOR_SIZE as the logical
block size during mmc_blk_alloc_req.
In order to use this patch for 4KB sector size, ensure that
USE_NATIVE_SECTOR is enabled, partition table is 4KB sector size
aligned and file system block and sector size are 4KB multiples.
Signed-off-by: Saugata Das <saugata.das@linaro.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
After the null check on md the code jumped to cmd_done, which then
will dereference md in mmc_blk_put. This patch avoids the possible
null pointer dereference in that case.
Signed-off-by: Philippe De Swert <philippedeswert@gmail.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC bus is using legacy suspend/resume method, which is not compatible if
runtime pm callbacks are used. In this scenario, MMC bus suspend/resume
callbacks cannot be called when system entering S3. So change to use the
new defined dev_pm_ops for system sleeping mode.
Tested on AM335x Platform. Solves major issue/crash reported at
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg65425.html
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Tested-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
eMMC v4.5 sanitize operation erases all copies of unmapped
data. However trim or erase operations must be used first
to unmap the required sectors. That was not being done.
Fixes apply to linux 3.2 on.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to the specifications for SD and (e)MMC default
blocksize (named BLOCKLEN in Spec.) must always be 512
bytes. Since we hardcoded to always use 512 bytes, we do
not explicitly have to set it. Future improvements should
potentially make it possible to use a greater blocksize
than 512 bytes, but until then let's skip this.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Subhash Jadavani <subhashj@codeauora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Core:
* Support for MMC 4.5 Data Tag feature -- we tag REQ_META, so devices
that support Data Tag will provide increased throughput for metadata.
* Faster detection of card removal on I/O errors.
Drivers:
* dw_mmc now supports eMMC Power Off Notify, has PCI support, and
implements pre_req and post_req for asynchronous requests.
* omap_hsmmc now supports device tree.
* esdhc now has power management support.
* sdhci-tegra now supports Tegra30 devices.
* sdhci-spear now supports hibernation.
* tmio_mmc now supports using a GPIO for card detection.
* Intel PCH now supports 8-bit bus transfers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=T4T+
-----END PGP SIGNATURE-----
Merge tag 'mmc-merge-for-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
Core:
* Support for MMC 4.5 Data Tag feature -- we tag REQ_META, so devices
that support Data Tag will provide increased throughput for metadata.
* Faster detection of card removal on I/O errors.
Drivers:
* dw_mmc now supports eMMC Power Off Notify, has PCI support, and
implements pre_req and post_req for asynchronous requests.
* omap_hsmmc now supports device tree.
* esdhc now has power management support.
* sdhci-tegra now supports Tegra30 devices.
* sdhci-spear now supports hibernation.
* tmio_mmc now supports using a GPIO for card detection.
* Intel PCH now supports 8-bit bus transfers.
* tag 'mmc-merge-for-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (53 commits)
mmc: sh_mmcif: simplify bitmask macros
mmc: sh_mobile_sdhi: support modular mmc-core with non-standard hotplug
mmc: sh_mobile_sdhi: add a callback for board specific init code
mmc: tmio: cosmetic: prettify the tmio_mmc_set_ios() function
mmc: sh_mobile_sdhi: do not manage PM clocks manually
mmc: tmio_mmc: remove unused sdio_irq_enabled flag
mmc: tmio_mmc: power status flag doesn't have to be exposed in platform data
mmc: sh_mobile_sdhi: pass card hotplug GPIO number to TMIO MMC
mmc: tmio_mmc: support the generic MMC GPIO card hotplug helper
mmc: tmio: calculate the native hotplug condition only once
mmc: simplify mmc_cd_gpio_request() by removing two parameters
mmc: sdhci-pci: allow 8-bit bus width for Intel PCH
mmc: sdhci: check interrupt flags in ISR again
mmc: sdhci-pci: Add MSI support
mmc: core: warn when card doesn't support HPI
mmc: davinci: Poll status for small size transfers
mmc: davinci: Eliminate spurious interrupts
mmc: omap_hsmmc: Avoid a regulator voltage change with dt
mmc: omap_hsmmc: Convert hsmmc driver to use device tree
mmc: sdhci-pci: add SDHCI_QUIRK2_HOST_OFF_CARD_ON for Medfield SDIO
...
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
MMC-4.5 data tag feature will be used to store the file system meta-data
in the tagged region of eMMC. This will improve the write and subsequent
read transfer time for the meta data.
Signed-off-by: Saugata Das <saugata.das@linaro.org>
Tested-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Kill block requests when the host realizes that the card is
removed from the slot and is sure that subsequent requests
are bound to fail. Do this silently so that the block
layer doesn't output unnecessary error messages.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enable boot partitions to be read-only locked until next power on via
a sysfs entry. There will be one sysfs entry for each boot partition:
/sys/block/mmcblkXbootY/ro_lock_until_next_power_on
Each boot partition is locked by writing 1 to its file.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: John Beckett <john.beckett@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If the read or write buffer size associated with the command sent
through the mmc_blk_ioctl is zero, do not prepare data buffer.
This enables a ioctl(2) call to for instance send a MMC_SWITCH to set
a byte in the ext_csd.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
No functional change; adds macros for card manufacturer IDs.
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: Andrei E. Warkentin <andrey.warkentin@gmail.com>
Cc: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Adds a quirk that sets the data read timeout to a fixed value instead
of relying on the information in the CSD. The timeout value chosen
is 300ms since that has proven enough for the problematic cards found,
but could be increased if other cards require this.
This patch also enables this quirk for certain Micron cards known to
have this problem.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Due to hardware bugs, some MMC host controllers don't support
multiple-block reads[1]. To resolve, add a new MMC capability flag,
MMC_CAP2_NO_MULTI_READ, which can be set by affected host controller
drivers. When this capability is set, all reads will be issued one
sector at a time.
1. See for example Advisory 2.1.1.128 "MMC: Multiple Block Read
Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_
Revision F (October 2010) (SPRZ278F), available from
http://focus.ti.com/lit/er/sprz278f/sprz278f.pdf
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Dave Hylands <dhylands@gmail.com>
Tested-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds cache feature of eMMC4.5 Spec.
If device supports cache capability, host can utilize some specific
operations.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC v4.5 supports the DISCARD feature (CMD38). It's different from
trim and there's no check bit. Currently it's only supported at v4.5.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the v4.5, there's no secure erase & trim support.
Instead it supports the sanitize feature.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
All the files using printk function for displaying kernel messages
in the mmc driver have been replaced with corresponding macro.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
It allows gerneral purpose partitions in MMC Device. And I try to simply
make mmc_blk_alloc_parts using mmc_part structure suggested by Andrei
Warkentin. After patching, we see general purpose partitions like this:
> cat /proc/partitions
179 0 847872 mmcblk0
179 192 4096 mmcblk0gp3
179 160 4096 mmcblk0gp2
179 128 4096 mmcblk0gp1
179 96 1052672 mmcblk0gp0
179 64 1024 mmcblk0boot1
179 32 1024 mmcblk0boot0
Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Andrei Warkentin <awarkentin@vmware.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Intel Medfield platform blocks access to eMMC boot partitions which
results in switch errors. Since there is no access, mmcboot0/1
devices should not be created. Add a host capability to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the case of a switch error, do not update partition config as though
the switch succeeded, and ensure blk_end_request is called on the
failed request.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Andrei Warkentin <andrey.warkentin@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For cards that support hardware reset (just eMMC), try a reset and
retry before returning an I/O error. However this is not done for
ECC errors and is never done twice for the same operation type
(READ, WRITE, DISCARD, SECURE DISCARD) until that type of operation
again succeeds.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix the sparse warning output "warning: Using plain integer as NULL pointer"
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a new REQ_PRIO to let requests preempt others in the cfq I/O schedule,
and lave REQ_META purely for marking requests as metadata in blktrace.
All existing callers of REQ_META except for XFS are updated to also
set REQ_PRIO for now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
We already check for ongoing async transfers when handling discard
requests, but not in mmc_blk_issue_flush(). This patch fixes that
omission.
Tested with an SDHCI controller and eMMC4.41.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Per Forlin <per.forlin@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Change mmc_blk_issue_rw_rq() to become asynchronous.
The execution flow looks like this:
* The mmc-queue calls issue_rw_rq(), which sends the request
to the host and returns back to the mmc-queue.
* The mmc-queue calls issue_rw_rq() again with a new request.
* This new request is prepared in issue_rw_rq(), then it waits for
the active request to complete before pushing it to the host.
* When the mmc-queue is empty it will call issue_rw_rq() with a NULL
req to finish off the active request without starting a new request.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Break out code without functional changes. This simplifies the code and
makes way for handling two parallel requests.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Sourav Poddar<sourav.poddar@ti.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Break out code from mmc_blk_issue_rw_rq to create a block request prepare
function. This doesn't change any functionallity. This helps when handling
more than one active block request.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The way the request data is organized in the mmc queue struct, it only
allows processing of one request at a time. This patch adds a new struct
to hold mmc queue request data such as sg list, request, blk request and
bounce buffers, and updates any functions depending on the mmc queue
struct. This prepares for using multiple active requests in one mmc queue.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Ulf Hansson