Add constants and callback functions for the dwmac on rk3128 soc.
As can be seen, the base structure is the same, only registers
and the bits in them moved slightly.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Treat the ef/04/01 interface class/subclass/protocol combination used
by the Novatel Verizon USB730L (1410:9030) as a possible RNDIS
interface.
T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#= 17 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 3
P: Vendor=1410 ProdID=9030 Rev=03.10
S: Manufacturer=Novatel Wireless
S: Product=MiFi USB730L
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 3 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=ef(misc ) Sub=04 Prot=01 Driver=rndis_host
I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
I: If#= 2 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid
Once the network interface is brought up, the user just needs to run a
DHCP client to get IP address and routing setup.
As a side note, other Novatel Verizon USB730L models with the same
vid:pid end up exposing a standard ECM interface which doesn't require
any other kernel update to make it work.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
When considering whether to set RTNH_F_OFFLOAD flag on an IPv6 route,
mlxsw_sp_fib6_entry_offload_set() looks up the mlxsw_sp_nexthop
corresponding to a given route, and decides based on whether the next
hop's offloaded flag was set. When looking for the matching next hop, it
also takes into account the device of the route, which must match next
hop's RIF.
IPIP next hops however hitherto didn't set the RIF. As a result, IPv6
routes forwarding traffic to IP-in-IP netdevices are never marked as
offloaded, even when they actually are.
Thus track RIF of IPIP next hops the same way as that of ETHERNET next
hops.
Fixes: 8f28a30976 ("mlxsw: spectrum_router: Support IPv6 overlay encap")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating a new RIF, bumping RIF count of the containing VR is the
last thing to be done. Symmetrically, when destroying a RIF, RIF count
is first dropped and only then the rest of the cleanup proceeds.
That's a problem for loopback RIFs. Those hold two VR references: one
for overlay and one for underlay. mlxsw_sp_rif_destroy() releases the
overlay one, and the deconfigure() callback the underlay one. But if
both overlay and underlay are the same, and if there are no other
artifacts holding the VR alive, this put actually destroys the VR. Later
on, when mlxsw_sp_rif_destroy() calls mlxsw_sp_vr_put() for the same VR,
the VR will already have been released and the kernel crashes with NULL
pointer dereference.
The underlying problem is that the RIF under destruction ends up
referencing the overlay VR much longer than it claims: all the way until
the call to mlxsw_sp_vr_put(). So line up the reference counting
properly to reflect this. Make corresponding changes in
mlxsw_sp_rif_create() as well for symmetry.
Fixes: 6ddb7426a7 ("mlxsw: spectrum_router: Introduce loopback RIFs")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If this sanity check fails, we must free 'rss_indir'. Otherwise there is a
memory leak.
'goto err' as done in the other error handling paths to fix it.
Fixes: 46a3df9f97 ("net: hns3: Fix for setting rss_size incorrectly")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.
The binding documentation is updating accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This linksys dongle by default comes up in cdc_ether mode.
This patch allows r8152 to claim the device:
Bus 002 Device 002: ID 13b1:0041 Linksys
Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_g2_irq_free locks the registers mutex, but not
mv88e6xxx_g1_irq_free, which results in a stack trace from
assert_reg_lock when unloading the mv88e6xxx module. Fix this.
Fixes: 3460a5770c ("net: dsa: mv88e6xxx: Mask g1 interrupts and free interrupt")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-enable the MAC receiver by setting CONFIG_RE before powering down,
as instructed in section 6.3.5.1 of [1]. Without this the MAC fails
to receive WoL packets and never wakes up.
[1] DWC Ethernet QoS Databook 4.10a October 2014
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hook to stmmac_pltfr_pm_ops for suspend / resume handling.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ports with the same VLAN must all be in the same bridge. However the
CPU and DSA ports need to be in multiple VLANs spread over multiple
bridges. So exclude them when performing this test.
Fixes: b2f81d304c ("net: dsa: add CPU and DSA ports as VLAN members")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch stops the internal MAC Tx clock from being enabled as the
internal clock isn't used. The definition used for the bit controlling
this behaviour is renamed as well as it was wrongly named (bit 4 of
GMAC_CTRL_2_REG).
Fixes: 3919357fb0 ("net: mvpp2: initialize the GMAC when using a port")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private port_list array has a list of pointers to mvpp2_port
instances. This list is allocated given the number of ports enabled in
the device tree, but the pointers are set using the port-id property. If
on a single port is enabled, the port_list array will be of size 1, but
when registering the port, if its id is not 0 the driver will crash.
Other crashes were encountered in various situations.
This fixes the issue by using an index not equal to the value of the
port-id property.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parsing fragmentation detection failed due to wrong configured
parser TCAM entry's. Some traffic was marked as fragmented in RX
descriptor, even it wasn't IP fragmented. The hardware also failed to
calculate checksums which lead to use software checksum and caused
performance degradation.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of calculating the offloads counters, count them explicitly.
The calculations done for these counters would result in bugs in some
cases, for example:
When running TCP traffic over a VXLAN tunnel with TSO enabled the following
counters would increase:
tx_csum_partial: 1,333,284
tx_csum_partial_inner: 29,286
tx4_csum_partial_inner: 384
tx7_csum_partial_inner: 8
tx9_csum_partial_inner: 34
tx10_csum_partial_inner: 26,807
tx11_csum_partial_inner: 287
tx12_csum_partial_inner: 27
tx16_csum_partial_inner: 6
tx25_csum_partial_inner: 1,733
Seems like tx_csum_partial increased out of nowhere.
The issue is in the following calculation in mlx5e_update_sw_counters:
s->tx_csum_partial = s->tx_packets - tx_offload_none - s->tx_csum_partial_inner;
While tx_packets increases by the number of GSO segments for each SKB,
tx_csum_partial_inner will only increase by one, resulting in wrong
tx_csum_partial counter.
Fixes: bfe6d8d1d4 ("net/mlx5e: Reorganize ethtool statistics")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Toggling of C-tag VLAN filter should not affect the "any S-tag" steering rule.
Fixes: 8a271746a2 ("net/mlx5e: Receive s-tagged packets in promiscuous mode")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use the correct formatting for netdev features.
Fixes: 0e405443e8 ("net/mlx5e: Improve set features ndo resiliency")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Encap entries cached by the driver could be invalidated due to
tunnel destination neighbour state changes.
When attempting to offload a flow that uses a cached encap entry,
we must check the entry validity and defer the offloading
if the entry exists but not valid.
When EAGAIN is returned, the flow offloading to hardware takes place
by the neigh update code when the tunnel destination neighbour
becomes connected.
Fixes: 232c001398 ("net/mlx5e: Add support to neighbour update flow")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When offloading header re-write, the HW may need to adjust checksums along
the packet. For IP traffic, and a case where we are asked to modify fields in
the IP header, current HW supports that only for TCP and UDP. Enforce it, in
this case fail the offloading attempt for non TCP/UDP packets.
Fixes: d7e75a325c ('net/mlx5e: Add offloading of E-Switch TC pedit (header re-write) actions')
Fixes: 2f4fe4cab0 ('net/mlx5e: Add offloading of NIC TC pedit (header re-write) actions')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In case the neighbour for the tunnel destination isn't valid,
we send a neighbour update request but we free the encap
header buffer. This is wrong, because we still need it for
allocating a HW encap entry once the neighbour is available.
Fix that by skipping freeing it if we wait for neighbour.
Fixes: 232c001398 ('net/mlx5e: Add support to neighbour update flow')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Added check for the maximal number of flow counters attached
to rule (FTE).
Fixes: bd5251dbf1 ('net/mlx5_core: Introduce flow steering destination of type counter')
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, FPGA capability is located in (mdev)->caps.hca_cur,
change the location to be (mdev)->caps.fpga,
since hca_cur is reserved for HCA device capabilities.
Fixes: e29341fb3a ("net/mlx5: FPGA, Add basic support for Innova")
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When cleaning rdma netdevice we need to save the mdev pointer
because priv is released when we release netdev.
This bug was found using the kernel address sanitizer (KASAN).
use-after-free in mlx5_rdma_netdev_free+0xe3/0x100 [mlx5_core]
Fixes: 48935bbb7a ("net/mlx5e: IPoIB, Add netdevice profile skeleton")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Quite a lot of fixes this time. Most notable is the brcmfmac fix for a
CVE issue.
iwlwifi
* a couple of bugzilla bugs related to multicast handling
* two fixes for WoWLAN bugs that were causing queue hangs and
re-initialization problems
* two fixes for potential uninitialized variable use reported by Dan
Carpenter in relation to a recently introduced patch
* a fix for buffer reordering in the newly supported 9000 device
family
* fix a race when starting aggregation
* small fix for a recent patch to wake mac80211 queues
* send non-bufferable management frames in the generic queue so they
are not sent on queues that are under power-save
ath10k
* fix a PCI PM related gcc warning
brcmfmac
* CVE-2017-0786: add length check scan results from firmware
* respect passive scan requests from user space
qtnfmac
* fix race in tx path when using multiple interfaces
* cancel ongoing scan when removing the wireless interface
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZyMFDAAoJEG4XJFUm622bKcwIAJrA+WBwvQUChcFGc5KWUaqB
+aJN1fP3AaiLHVU0Ny1jNIPYPREH9/EejCI72i2WE5TH73sAbqL/XPn8Y5pETQ25
FvKSnTZJyjbU0PNa5pgdYVDr+ZJ21z4hD9OdSRib6Ru62o21ISqzsT5bqd9g3btX
KRDqaAqkQYiMpL73KuF+89RmeUjXNM0GFbdxvziRV3mKYqqZiqNNQLxKlPOCcAD0
2AOyX+k2FLiG5+/RvrcLiCjUzwzQzxwhwQZe1w+ncFRX5INvESLWHDWyzYcB5C0M
9iKc6QVaWTFGqsVyGk+M2decKuj5wHaPVMGc3g7FYWBJo/CVsmpW+kbNrJ/FG08=
=s1IH
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-09-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.14
Quite a lot of fixes this time. Most notable is the brcmfmac fix for a
CVE issue.
iwlwifi
* a couple of bugzilla bugs related to multicast handling
* two fixes for WoWLAN bugs that were causing queue hangs and
re-initialization problems
* two fixes for potential uninitialized variable use reported by Dan
Carpenter in relation to a recently introduced patch
* a fix for buffer reordering in the newly supported 9000 device
family
* fix a race when starting aggregation
* small fix for a recent patch to wake mac80211 queues
* send non-bufferable management frames in the generic queue so they
are not sent on queues that are under power-save
ath10k
* fix a PCI PM related gcc warning
brcmfmac
* CVE-2017-0786: add length check scan results from firmware
* respect passive scan requests from user space
qtnfmac
* fix race in tx path when using multiple interfaces
* cancel ongoing scan when removing the wireless interface
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_frag_dma_map multiple times if tx length is greater than
device max and avoid processing tx ring until entire packet has been
sent.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a bug in aquantia atlantic card firmware, it sometimes reports
invalid link speed bits. That caused driver to report link down events,
although link itself is totally fine.
This patch ignores such out of blue readings.
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver did a poor job in managing its Tx queues: Sometimes it could stop
tx queues due to link down condition in aq_nic_xmit - but never waked up
them. That led to Tx path total suspend.
This patch fixes this and improves generic queue management:
- introduces queue restart counter
- uses generic netif_ interface to disable and enable tx path
- refactors link up/down condition and introduces dmesg log event when
link changes.
- introduces new constant for minimum descriptors count required for queue
wakeup
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although hardware is capable for almost 16K MTU, without max_mtu field
correctly set it only allows standard MTU to be used.
This patch enables max MTU, calculating it from hardware maximum frame size
of 16352 octets (including FCS).
Fixes: 5513e16421 ("net: ethernet: aquantia: Fixes for aq_ndev_change_mtu")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inlining these functions creates lots of stack variables that each take
64 bytes when KASAN is enabled, leading to this warning about potential
stack overflow:
drivers/net/ethernet/rocker/rocker_ofdpa.c: In function 'ofdpa_cmd_flow_tbl_add':
drivers/net/ethernet/rocker/rocker_ofdpa.c:621:1: error: the frame size of 2752 bytes is larger than 1536 bytes [-Werror=frame-larger-than=]
gcc-8 can now consolidate the stack slots itself, but on older versions
we get the same behavior by using a temporary variable that holds a
copy of the inline function argument.
Cc: stable@vger.kernel.org
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mapping the RX DMA buffers, the driver was accidentally specifying
zero for the buffer length. Under normal circumstances, SWIOTLB does not
need to allocate a bounce buffer, so the address is just mapped without
checking the size field. This is why the error was not detected earlier.
Fixes: b9b17debc6 ("net: emac: emac gigabit ethernet controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the error handling paths 'goto error', except this one.
We should also go to error in this case, or some resources will be
leaking.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given NR_IRQS is 2048 on sparc64, and even 32784 on alpha, 3 digits is
not enough to represent interrupt numbers on all architectures. Hence
PHY interrupt numbers may be truncated during printing.
Increase the buffer size from 4 to 8 bytes to fix this.
Fixes: 5e369aefdc ("net: stmmac: Delete dead code for MDIO registration")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure (of/i2c/platform)_device_id tables are NULL terminated.
Found by coccinelle spatch "misc/of_table.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use default value of auto duplex and auto speed values loaded
from EEPROM/OTP after reset. The LAN78xx allows platform
configurations to be loaded from EEPROM/OTP.
Ex: When external phy is connected, the MAC can be configured to
have correct auto speed, auto duplex, auto polarity configured
from the EEPROM/OTP.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow EEPROM write for less than MAX_EEPROM_SIZE
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix for eeprom read/write when device auto suspend
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit 2d55173e71 ("phy: add generic function to support
ksetting support"), we lost the ability to report the transceiver type
like we used to. Now that we have added back the transceiver type to
ethtool_link_settings, we can report it back like we used to and have no
loss of information.
Fixes: 3f1ac7a700 ("net: ethtool: add new ETHTOOL_xLINKSETTINGS API")
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EMAC has the option of sending only a single pause frame when
flow control is enabled and the RX queue is full. Although sending
only one pause frame has little value, this would allow admins to
enable automatic flow control without having to worry about the EMAC
flooding nearby switches with pause frames if the kernel hangs.
The option is enabled by using the single-pause-mode private flag.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If MTU is changed the host would reject the send buffer change.
This problem is result of recent change to allow changing send
buffer size.
Every time we change the MTU, we store the previous net_device section
count before destroying the buffer, but we don’t store the previous
section size. When we reinitialize the buffer, its size is calculated
by multiplying the previous count and previous size. Since we
continuously increase the MTU, the host returns us a decreasing count
value while the section size is reinitialized to 1728 bytes every
time.
This eventually leads to a condition where the calculated buf_size is
so small that the host rejects it.
Fixes: 8b5327975a ("netvsc: allow controlling send/recv buffer size")
Signed-off-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_PM_SLEEP is disabled, we get a compile-time
warning:
drivers/net/wireless/ath/ath10k/pci.c:3417:12: error: 'ath10k_pci_pm_resume' defined but not used [-Werror=unused-function]
static int ath10k_pci_pm_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath10k/pci.c:3401:12: error: 'ath10k_pci_pm_suspend' defined but not used [-Werror=unused-function]
static int ath10k_pci_pm_suspend(struct device *dev)
Rather than fixing the #ifdef, this just marks both functions
as __maybe_unused, which is a more robust way to do this.
Fixes: 32faa3f0ee ("ath10k: add the PCI PM core suspend/resume ops")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Current mapping between pri and tc is one to one,
so user can't map multi priorities to the same tc.
This patch changes the mapping to many to one.
Fixes: 848440544b ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rss_size is 1, 2, 4, 8, 16, 32, 64, 128, but acutal tc queue
size can be any u16 less than 128. If tc queue size is 5, we
set the rss_size to 8, indirection table will be used to limit
the size of actual queue size.
It may cause dropping of receiving packet in hardware if
rss_size is not set correctly.
For now, each TC has the same rss size.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a typo error for feild, which should be field.
Fixes: 848440544b ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Wu