This patch contains a printk reorder to remove the current problem of
displaying "PCI-DMA: Disabling IOMMU." and then "PCI-DMA: using GART
IOMMU" 20 lines later in dmesg.
It also constains a printk reorder in swiotlb to state swiotlb
enablement prior to describing the location of the bounce buffers, and a
printk reorder to state gart enablement prior to describing the
aperature.
Also constains a whitespace cleanup in arch/x86_64/kernel/setup.c
Tested (along with patch 2/2) on dual opteron with gart enabled,
iommu=soft, and iommu=off.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hack for 2.6.16. In 2.6.17 all code that uses NR_CPUs should
be audited and changed to only touch possible CPUs.
Don't mark the reference per cpu data init data (so it stays
around after boot) and point all impossible CPUs to it. This way
they reference some valid - although shared memory. Usually
this is only initialization like INIT_LIST_HEADs and there
won't be races because these CPUs never run. Still somewhat hackish.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's bad juju to touch the APIC when it hasn't been enabled.
I also moved ack_bad_irq for x86-64 out of line following i386.
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Checking of the validity of pointers should be consistently done before
dereferencing the pointer.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conditionalize two unwind directives to match other similarly
conditional code.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Cc: Jim Houston <jim.houston@ccur.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On some broken motherboards (at least one NForce3 based AMD64 laptop)
the PIT timer runs at a incorrect frequency. This patch adds a new
option "apicpmtimer" that allows to use the APIC timer and calibrate it
using the PMTimer. It requires the earlier patch that allows to run the
main timer from the APIC.
Specifying apicpmtimer implies apicmaintimer.
The option defaults to off for now.
I tested it on a few systems and the resulting APIC timer frequencies
were usually a bit off, but always <1%, which should be tolerable.
TBD figure out heuristic to enable this automatically on the affected
systems TBD perhaps do it on all NForce3s or using DMI?
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kprobes cannot deal with the funny calling conventions when it
runs on a different stack when it returns. If someone wants
to instrument context switch they can add a probe to schedule()
instead.
Cc: jkenisto@us.ibm.com, prasanna@in.ibm.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Align the start of the per-cpu section to the configured number of bytes in a
cache line. This stops a BUG_ON() from triggering in load_module() when
DEFINE_PER_CPU() is used in a module and the section isn't cacheline-aligned.
Rusty also found this and sent a patch in a while ago
(http://lkml.org/lkml/2004/10/19/17), I don't know what came of that.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[ AK: I redid Kevin's fix to be simpler, but the idea and original
analysis of the problem is from Kevin]
This avoid allocation failures on some SATA systems like Nvidia CK8
when the IOMMU gets fragmented. Modern SATA devices have quite large queues
(128 entries) and the FS with ext2/3 is good enough now that it often
passes whole 128 page sg lists down to the driver. These require
512K of continuous free space in the IOMMU aperture to map when merged.
When the IOMMU is fragmented this could lead to spurious IO errors
due to failing mappings.
Short term fix is to just try to map the SG list again unmerged
page by page - this way fragmentation doesn't matter anymore.
The code for that was already there, but it just wasn't enabled for the
merge case.
According to Kevin at least the Nvidia device doesn't seem to benefit
from merging much anyways, so the only slowdown is from trying
to do an unnecessary merge attempt.
Kevin plans to implement better fragmentation avoidance in the future,
but that wouldn't be 2.6.16 material.
TBD: should add some statistic counters to count how often that really
happens.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I broke this earlier when moving the patch from i386 to x86-64.
Need to return the virtual address here, not the physical address.
This fixes some boot time crashes on x86-64.
Cc: gregkh@suse.de
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Check if the processor/memory affinity entries are long enough
according to the ACPI 3.0 spec.
- Ignore memory affinity entries that define a zero length region.
All based on BIOS issues found in the field @)
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
attached patch is 2 more cases i found via running the reference_init.pl
script. These were easy to spot just knowing the file names. There is
one another about init/main.c that i cant exactly zero in. (partly
because i dont know how to interpret the data thats spewed out of the tool).
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It has been enabled by default for some time now and is cheap enough
so it doesn't matter anyways.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently, x86_64 and ia64 arches do not clear the corresponding bits
in the node's cpumask when a cpu goes down or cpu bring up is cancelled.
This is buggy since there are pieces of common code where the cpumask is
checked in the cpu down code path to decide on things (like in the slab
down path). PPC does the right thing, but x86_64 and ia64 don't (This
was the reason Sonny hit upon a slab bug during cpu offline on ppc and
could not reproduce on other arches). This patch fixes it for x86_64.
I won't attempt ia64 as I cannot test it.
Credit for spotting this should go to Alok.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They cause quite bad performance regressions on Netburst
This is temporary until we can get new optimized functions
for these CPUs.
This undoes changes that were done in 2.6.15 and in 2.6.16-rc1,
essentially bringing the code back to 2.6.14 level. Only change
is I renamed the X86_FEATURE_K8_C flag to X86_FEATURE_REP_GOOD
and fixed the check for the flag and also fixed some comments.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This avoids BUG_ONs in the low level allocator when an illegal
GFP mask is added.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
At resume time, TSC's value or something similar might be changed a lot
against suspend time. This could make system gets a very big lost ticks.
See http://bugzilla.kernel.org/show_bug.cgi?id=5825
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They all have problems with IRQ 0 routing, so just use the APIC on them.
Can be overwritten with "noapicmaintimer"
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Another piece from the no-idle-tick patch.
This can be enabled with the "apicmaintimer" option.
This is mainly useful when the PIT/HPET interrupt is unreliable.
Note there are some systems that are known to stop the APIC
timer in C3. For those it will never work, but this case
should be automatically detected.
It also only works with PM timer right now. When HPET is used
the way the main timer handler computes the delay doesn't work.
It should be a bit more efficient because there is one less
regular interrupt to process on the boot processor.
Requires earlier bugfix from Venkatesh
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A kprobe executes IRET early and that could cause NMI recursion
and stack corruption.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This assembly version is measurably faster than the generic version in
lib/iomap_copy.c.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to use the compat function here.
Pointer out by Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Handle more bogus MCFG entries
Some Asus P4 boards seem to have broken MCFG tables with
only a single entry for busses 0-0. Special case these
and assume they mean all busses can be accessed.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a typo/mis-merge in one of the previous patches.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds the ability to disability packet split at compile time and use the legacy receive path on PCI express hardware. Made this a CONFIG option and modified the Kconfig, to reflect the new option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add x86-64 specific memory hot-add functions, Kconfig options,
and runtime kernel page table update functions to make
hot-add usable on x86-64 machines. Also, fixup the nefarious
conditional locking and exports pointed out by Andi.
Tested on Intel and IBM x86-64 memory hot-add capable systems.
Signed-off-by: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Another try at this.
For 32bit follow the 32bit implementation from Ingo -
mappings are growing down from the end of stack now
and vary randomly by 1GB.
Randomized mappings for 64bit just vary the normal mmap break
by 1TB. I didn't bother implementing full flex mmap for 64bit
because it shouldn't be needed there.
Cc: mingo@elte.hu
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... as they are no longer needed. Since there were hard-coded numbers in the
file, the patch also adds a mechanism to avoid these (otherwise potential
future changes would again and again require adjusting these numbers).
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The comparison of the initrd start address against "&_end" is
unnecessary and incorrect. Make it match the x86 code that just
compares the passed-in arguments.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For not fully explained reasons it broke mem=... on several setups.
Also minor cleanup.
Cc: axboe@suse.de
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To avoid mistakes.
I got a few reports where people got broken timing because they didn't
have the PMTIMER fallback.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This unbreaks recursive kprobes which didn't work anymore
due to an earlier patch which converted the debug entry point
to use an IST.
This also allows nesting of the debug entry point too.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o This fix was posted for i386 long back. Posting it for x86_64.
http://marc.theaimsgroup.com/?l=linux-kernel&m=110380103229830&w=2
o This patch fixes the problem of secondary cpus boot up. This situation
is faced when kernel is built for default locations like 16MB and
onwards. In this configuration, only primary cpu (BP) comes and
secondary cpus don't boot.
o Problem occurs because in trampoline code, lgdt is not able to load the
GDT as it happens to be situated beyond 16MB. This is due to the fact
that cpu is still in real mode and default operand size is 16bit.
o This patch uses lgdtl instead of lgdt to force operand size to 32
instead of 16.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... reducing the amount of changes Xen has to do.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The explicit and implicit calls to setup_early_printk() were passing
inconsistent arguments.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Previously they would be only allocated before the kernel text at
1MB. This limited the maximum supported memory to 128GB.
Now allow the e820 allocator to put them everywhere. Try
to put them beyond any DMA zones to avoid filling them up.
This should free some GFP_DMA memory compared to earlier kernels.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
hard_smp_processor_id would return the local APIC id instead
of the Linux processor id. On big systems they are often
not identical. safe_smp_processor_id is just a wrapper
around it that does the necessary conversions.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove support for obsolete hardware and cleanup.
- Remove checks for non integrated APICs
- Replace apic_write_around with apic_write.
- Remove apic_read_around
- Remove APIC version reads used by old workarounds
- Remove old workaround for Simics
- Fix indentation
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When building in a separate objtree, file names produced by BUG() & Co. can
get fairly long; printing only the first 50 characters may thus result in
(almost) no useful information. The following change makes it so that rather
the last 50 characters of the filename get printed.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Especially under Xen, where the console cannot be adjusted to more than 25
lines, it is fairly important that the information displayed during a panic
is as compact as possible. Below adjustments work towards that.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Due to a broken condition, the body of the loop that is intended to wait for
the Update-In-Progress bit to get set and then cleared again was never
entered; in fact, the entire loop was optimized out by the compiler. Here is
a change to fix the condition (and to also move the initialization of locals
out of the spin lock protected region).
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It was only needed for APM
Pointed out by Jan Beulich
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
X86_FEATURE_K8_C was a synthetic Linux CPUID flag that was used for some
code optimizations in Opteron C stepping or later. But support for pre C
stepping optimizations has been removed, so this isn't needed anymore.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Saves about ~18K .text in defconfig
There would be more optimization potential, but that's for later.
Suggestion originally from Bill Irwin.
Fix from Andy Whitcroft.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They used to be used by the reboot code, but not anymore.
Noticed by Jan Beulich
Cc: JBeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Currently, during kexec reboot, IOAPIC is re-programmed back to virtual
wire mode if there was an i8259 connected to it. This enables getting
timer interrupts in second kernel in legacy mode.
o After putting into virtual wire mode, IOAPIC delivers the i8259 interrupts
to CPU0. This works well for kexec but not for kdump as we might crash
on a different CPU and second kernel will not see timer interrupts.
o This patch modifies the redirection table entry to deliver the timer
interrupts to the cpu we are rebooting (instead of hardcoding to zero).
This ensures that second kernel receives timer interrupts even on a
non-boot cpu.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce vSMP arch to the kernel.
This patch:
1. Adds CONFIG_X86_VSMP
2. Adds machine specific macros for local_irq_disabled, local_irq_enabled
and irqs_disabled
3. Writes to the vSMP CTL device to indicate kernel compiled with CONFIG_VSMP
Signed-off-by: Ravikiran Thirumalai <kiran@scalemp.com>
Signed-off-by: Shai Fultheim <shai@scalemp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently we attempt to restore virtual wire mode on reboot, which only
works if we can figure out where the i8259 is connected. This is very
useful when we are kexec another kernel and likely helpful to an peculiar
BIOS that make assumptions about how the system is setup.
Since the acpi MADT table does not provide the location where the i8259 is
connected we have to look at the hardware to figure it out.
Most systems have the i8259 connected the local apic of the cpu so won't be
affected but people running Opteron and some serverworks chipsets should be
able to use kexec now.
In addition this patch removes the hard coded assumption that the io_apic
that delivers isa interrups is always known to the kernel as io_apic 0.
There does not appear to be anything to guarantee that assumption is true.
And From: Vivek Goyal <vgoyal@in.ibm.com>
A minor fix to the patch which remembers the location of where i8259 is
connected. Now counter i has been replaced by apic. counter i is having
some junk value which was leading to non-detection of i8259 connected to
IOAPIC.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Setting RF (resume flag) allows a debugger to resume execution after a code
breakpoint without tripping the breakpoint again. It is reset by the CPU
after executing one instruction.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It was set as an NMI, but the NMI bit always forces an interrupt
to end up at vector 2. So it was never used. Remove.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix
CC arch/x86_64/kernel/nmi.o
linux/arch/x86_64/kernel/nmi.c: In function ???check_nmi_watchdog???:
linux/arch/x86_64/kernel/nmi.c:155: warning: statement with no effect
on Uniprocessor builds.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch uses a static PDA array early at boot and reallocates processor PDA
with node local memory when kmalloc is ready, just before pda_init.
The boot_cpu_pda is needed since the cpu_pda is used even before pda_init for
that cpu is called (to set the static per-cpu areas offset table etc)
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch enables early intialization of cpu_to_node.
apicid_to_node is built by reading the SRAT table, from acpi_numa_init with
ACPI_NUMA and k8_scan_nodes with K8_NUMA.
x86_cpu_to_apicid is built by parsing the ACPI MADT table, from acpi_boot_init.
We combine these two tables and setup cpu_to_node.
Early intialization helps the static per_cpu_areas in getting pages from
correct node.
Change since last release:
Do not initialize early init_cpu_to_node for faking node cases.
Patch tested on TYAN dual core 4P board with K8 only, ACPI_NUMA.
Tested on EM64T NUMA. Also tested with numa=off, numa=fake, and running
a kernel compiled with NUMA on a regular EM64 2 way SMP.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The real vsyscall .text addresses are not mapped when the alternative()
replacement runs early, so use some black magic to access them using
the direct mapping.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They already do this in hardware and the Linux algorithm
actually adds errors.
Cc: mingo@elte.hu
Cc: rohit.seth@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Apic id is in most significant 8 bits of APIC_ID register. Current code
is trying to write apic id to least significant 8 bits. This patch fixes
it.
o This fix enables booting uni kdump capture kernel on a cpu with non-zero
apic id.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove exports that are already exported from the object's source file.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These functions are inlines and shouldn't be exported.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Remove optimization for old B stepping Opteron
- Make the fast path for copies with a multiple of eight length faster.
- Minor instruction rearrangement to hopefully avoid a pipeline
stall or two.
- Add comment about errata to consider.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AK: I hacked Muli's original patch a lot and there were a lot
of changes - all bugs are probably to blame on me now.
There were also some changes in the fall back behaviour
for swiotlb - in particular it doesn't try to use GFP_DMA
now anymore. Also all DMA mapping operations use the
same core dma_alloc_coherent code with proper fallbacks now.
And various other changes and cleanups.
Known problems: iommu=force swiotlb=force together breaks
needs more testing.
This patch cleans up x86_64's DMA mapping dispatching code. Right now
we have three possible IOMMU types: AGP GART, swiotlb and nommu, and
in the future we will also have Xen's x86_64 swiotlb and other HW
IOMMUs for x86_64. In order to support all of them cleanly, this
patch:
- introduces a struct dma_mapping_ops with function pointers for each
of the DMA mapping operations of gart (AMD HW IOMMU), swiotlb
(software IOMMU) and nommu (no IOMMU).
- gets rid of:
if (swiotlb)
return swiotlb_xxx();
- PCI_DMA_BUS_IS_PHYS is now checked against the dma_ops being set
This makes swiotlb faster by avoiding double copying in some cases.
Signed-Off-By: Muli Ben-Yehuda <mulix@mulix.org>
Signed-Off-By: Jon D. Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Broken BIOS on Iwill 8way systems reports these and it causes the bootmem
allocator to crash. Add a sanity check if all the PXMs in the
SRAT table cover all memory as reported by e820. If the sanity
check fails the SRAT is rejected and the code will fall back
to discover the NUMA topology using the K8 northbridge registers
when applicable.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds a new notifier chain that is called with IDLE_START
when a CPU goes idle and IDLE_END when it goes out of idle.
The context can be idle thread or interrupt context.
Since we cannot rely on MONITOR/MWAIT existing the idle
end check currently has to be done in all interrupt
handlers.
They were originally inspired by the similar s390 implementation.
They have a variety of applications:
- They will be needed for CONFIG_NO_IDLE_HZ
- They can be used for oprofile to fix up the missing time
in idle when performance counters don't tick.
- They can be used for better C state management in ACPI
- They could be used for microstate accounting.
This is just infrastructure so far, no users.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix off by one when checking if the machine has enougn memory to need IOMMU
This caused the IOMMUs to be needlessly enabled for mem=4G
Based on a patch from Jon Mason
Signed-off-by: jdmason@us.ibm.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Whenever we see that a CPU is capable of C3 (during ACPI cstate init), we
disable local APIC timer and switch to using a broadcast from external timer
interrupt (IRQ 0).
Patch below adds the code for x86_64.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the finer control of local APIC timer. We cannot provide a sub-jiffy
control like this when we use broadcast from external timer in place of
local APIC. Instead of removing this only on systems that may end up using
broadcast from external timer (due to C3), I am going the
"I'm feeling lucky" way to remove this fully. Basically, I am not sure about
usefulness of this code today. Few other architectures also don't seem to
support this today.
If you are using profiling and fine grained control and don't like this going
away in normal case, yell at me right now.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I would like to throw out a suggestion for a possible change in the way that
the debug register traps are handled in do_debug() when the trap occurs
in kernel-mode.
In the x86_64 version of do_debug(), the code will skip around sending
a SIGTRAP to the current task if the trap occurred while in kernel mode.
On the i386-side of things, if the access happens to occur in kernel mode
(say during a read(2) of user's buffer that matches the address of a
debug register trap), then the do_debug() routine for i386 will go ahead
and call send_sigtrap() and send the SIGTRAP signal. The send_sigtrap()
code will also set the info.si_addr to NULL in this case (even though I
don't understand why, since the SIGTRAP siginfo processing doesn't use
the si_addr field...).
So I would like to suggest that the x86_64 do_debug() routine also
follow this type of behavior and have it go ahead and send the
SIGTRAP signal to the current task, even if the debug register trap
happens to have occurred in kernel mode. I have taken a stab at
a patch for this change below. (It includes the i386-ish change
for setting si_addr to NULL when the trap occurred in kernel mode.)
It seems like a useful feature to be able to 'watch' a user location that
might also be modified in the kernel via a system service call, and have the
debugger report that information back to the user, rather than to just
silently ignore the trap.
Additionally, I realize that users that pull in a kernel debugger such as
KGDB into their kernel might want to remove this change below when they add
in KGDB support. However, they could alternatively look at the current
task's thread.debugreg[] values to see if the trap occurred due to KGDB
or instead because of a user-space debugger trap, and still honor the
user SIGTRAP processing (instead of the KGDB breakpoint processing)
if the trap matches up with the thread.debugreg[] registers.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Much better to deal with these than with the magic numbers.
And remove the comment describing the bits - kernel source
is no replacement for an architecture manual.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't need to do the vmalloc check for the module range because its
PML4 is shared with the kernel text.
Also removed an unnecessary TLB flush.
Pointed out by Jan Beulich
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is on the same lines as Zachary Amsden's i386 GDT page alignemnt
patch in -mm, but for x86_64.
Patch to align and pad x86_64 GDT on page boundries.
[AK: some minor cleanups and fixed incorrect TLS initialization
in CPU init.]
Signed-off-by: Nippun Goel <nippung@calsoftinc.com>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This might help on distributions that use a 32bit biarch compiler.
First pass -m64 by default.
Secondly add some more .code32s because at least the Ubuntu biarch
32bit as called by gcc doesn't seem to handle -m64 -m32 as generated
by the Makefile without such assistance.
And finally make sure the linker script can be preprocessed
with a 32bit cpp.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attempt to avoid overflow in __delay caused varying precision
on different CPUs depending on differences in the CPU speed.
We should be able to do this multiplication with out overflowing
provided the
cpu is running at less than about 128 GHz. xloops < 20000 * 0x10c6.
loops_per_jiffy * HZ <= cpu_clock_speed. So if the cpu clock speed
< 2^64/(20000 * 0x10c6) = 2^64/ 51E6CC0 < 2^64/2^27 = 2^37 = 128G we
will not overflow the calculation.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we don't know the node a PCI bus is connected to return -1.
This matches the generic code.
Noticed by Ravikiran G Thirumalai <kiran@scalex86.org>
Cc: Ravikiran G Thirumalai <kiran@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A lot of Opteron BIOS just pass 10 in all SLIT entries (10 is the
normalized unit). This is actually worse than the default heuristic
because it leads to pci_distance not knowing the difference between
local and remote nodes anymore. This messes up some NUMA
heuristics in generic code.
In this case it's better to fall back to the default heuristic
which just does nodea == nodeb ? 10 : 20.
This patch does some basic sanity checking on the SLIT and only accepts
the SLIT when it passes.
Invariants enforced are:
- Node to itself shall be 10
- Any other distance shouldn't be 10
- Distances smaller than 10 are illegal
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some people need it now on 64bit so reuse the i386 code for
x86-64. This will be also useful for future bug workarounds.
It is a bit simplified there because there is no need
to do it very early on x86-64. This means it doesn't need
early ioremap et.al. We run it as a core initcall right now.
I hope it's not needed for early setup.
I added a general CONFIG_DMI symbol in case IA64 or someone
else wants to reuse the code later too.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This was a backup file that somehow made it into the official
tree. Never used for anything. Remove.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The introduction of call_softirq switching to the interrupt stack several
releases earlier resulted in a problem with the code in show_trace, which
assumes that it can pick the previous stack pointer from the end of the
interrupt stack.
Cc: Andi Kleen <ak@muc.de>
Cc: Arjan van de Ven <arjanv@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Be more careful with TF handling to fix some copy protection codes in wine
patch originally for i386 by Linus, then ported to x86_64 by Andi Kleen
see: [PATCH] x86_64: Some fixes for single step handling
commit: be61bff789
But it was never applied to the ia32 emulation code which breaks some
copy-protection schemes under wine when running on x86_64.
Signed-off-by: Peter Beutner <p.beutner@gmx.net>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
So why are we calling smp_send_stop from machine_halt?
We don't.
Looking more closely at the bug report the problem here
is that halt -p is called which triggers not a halt but
an attempt to power off.
machine_power_off calls machine_shutdown which calls smp_send_stop.
If pm_power_off is set we should never make it out machine_power_off
to the call of do_exit. So pm_power_off must not be set in this case.
When pm_power_off is not set we expect machine_power_off to devolve
into machine_halt.
So how do we fix this?
Playing too much with smp_send_stop is dangerous because it
must also be safe to be called from panic.
It looks like the obviously correct fix is to only call
machine_shutdown when pm_power_off is defined. Doing
that will make Andi's assumption about not scheduling
true and generally simplify what must be supported.
This turns machine_power_off into a noop like machine_halt
when pm_power_off is not defined.
If the expected behavior is that sys_reboot(LINUX_REBOOT_CMD_POWER_OFF)
becomes sys_reboot(LINUX_REBOOT_CMD_HALT) if pm_power_off is NULL
this is not quite a comprehensive fix as we pass a different parameter
to the reboot notifier and we set system_state to a different value
before calling device_shutdown().
Unfortunately any fix more comprehensive I can think of is not
obviously correct. The core problem is that there is no architecture
independent way to detect if machine_power will become a noop, without
calling it.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I noticed that some lowlevel send_IPI_mask helpers had a hotplug/preempt
race whereupon the cpu_online_map was read before disabling preemption;
...
cpumask_t mask = cpu_online_map;
int cpu = get_cpu();
cpu_clear(cpu, mask);
...
But then i realised that there is no need for these lowlevel functions to
be going through all this trouble when all the callers are already made
hotplug/preempt safe.
Signed-off-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is one CPU here whose MCE bank count is 6. This patch increases
x86_64's MCE bank count.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following is probably a good idea given that the atomic_set() isn't
a barrier here either.
Signed-off-by: Benjamin LaHaise <benjamin.c.lahaise@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This
- switches the INT3 handler to run on an IST stack (to cope with
breakpoints set by a kernel debugger on places where the kernel's
%gs base hasn't been set up, yet); the IST stack used is shared with
the INT1 handler's
[AK: this also allows setting a kprobe on the interrupt/exception entry
points]
- allows nesting of INT1/INT3 handlers so that one can, with a kernel
debugger, debug (at least) the user-mode portions of the INT1/INT3
handling; the nesting isn't actively enabled here since a kernel-
debugger-free kernel doesn't need it
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Print bits for RDTSCP, SVM, CR8-LEGACY.
Also now print power flags on i386 like x86-64 always did.
This will add a new line in the 386 cpuinfo, but that shouldn't
be an issue - did that in the past too and I haven't heard
of any breakage.
I shrunk some of the fields in the i386 cpuinfo_x86 to chars
to make up for the new int "x86_power" field. Overall it's
smaller than before.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define it for i386 too.
This is a synthetic flag that signifies that the CPU's TSC runs
at a constant P state invariant frequency.
Fix up the logic on x86-64/i386 to set it on all known CPUs.
Use the AMD defined bit to set it on future AMD CPUs.
Cc: venkatesh.pallipadi@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Was only used by the floppy driver to work around some ancient
hardware bug that should never occur on any 64bit system.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Most users don't need it so no need to waste memory.
This means an user has to specify the appropiate number of
hotplug CPUs on the command line with additional_cpus=...
or fix their BIOS to follow the convention in
Documentation/x86-64/cpu-hotplug-spec
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adjust page fault protection error check before considering it to be
a vmalloc synchronization candidate.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sure no iret can fault without attached recovery code.
Cannot happen in the normal case, but might be useful
with kernel debuggers
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since a double fault always implies that kernel data structures are
corrupt, this fault should neither be handed to user mode handling,
nor should the handler allow resuming the faulting code stream (since
architecturally this isn't a fault, but an abort).
Note that this slightly depends on the previously submitted patch
adjusting the prototype of notify_die() (a compiler warning will result
without that other patch).
AK: Removed obsolete CONFIG_CHECKING code, added comments
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adjusts things so that handlers of the die() notifier will have
sufficient information about the trap currently being handled. It also
adjusts the notify_die() prototype to (again) match that of i386.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Other than apparently commonly assumed, the bound instruction does not
require the corresponding IDT entry to have DPL 3.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As a follow-up to the introduction of CONFIG_UNWIND_INFO, this
separates the generation of frame unwind information for x86-64 from
that of full debug information.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on the documentation recently posted by Richard Brunner.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Frame unwind information was still incorrect for ia32_ptregs_common
(sorry, my fault), and could be improved for some of the other entry
points.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch: Use <linux/capability.h> where capable() is used.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a window where a probe gets removed right after the probe is hit
on some different cpu. In this case probe handlers can't find a matching
probe instance related to break address. In this case we need to read the
original instruction at break address to see if that is not a break/int3
instruction and recover safely.
Previous code had a bug where we were not checking for the above race in
case of reentrant probes and the below patch fixes this race.
Tested on IA64, Powerpc, x86_64.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch (against 2.6.15-rc5-mm3) fixes a kprobes build break
due to changes introduced in the kprobe locking in 2.6.15-rc5-mm3. In
addition, the patch reverts back the open-coding of kprobe_mutex.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently arch_remove_kprobes() is only implemented/required for x86_64 and
powerpc. All other architecture like IA64, i386 and sparc64 implementes a
dummy function which is being called from arch independent kprobes.c file.
This patch removes the dummy functions and replaces it with
#define arch_remove_kprobe(p, s) do { } while(0)
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on some feedback from Oleg Nesterov, I have made few changes to
previously posted patch.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since Kprobes runtime exception handlers is now lock free as this code path is
now using RCU to walk through the list, there is no need for the
register/unregister{_kprobe} to use spin_{lock/unlock}_isr{save/restore}. The
serialization during registration/unregistration is now possible using just a
mutex.
In the above process, this patch also fixes a minor memory leak for x86_64 and
powerpc.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These days ioctl32.h is only used for communication of fs/compat.c and
fs/compat_ioctl.c and doesn't contain anything of interest to drivers.
Remove inclusion in various drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that all these entries in the arch ioctl32.c files are gone [1], we can
build fs/compat_ioctl.c as a normal object and kill tons of cruft. We need a
special do_ioctl32_pointer handler for s390 so the compat_ptr call is done.
This is not needed but harmless on all other architectures. Also remove some
superflous includes in fs/compat_ioctl.c
Tested on ppc64.
[1] parisc still had it's PPP handler left, which is not fully correct
for ppp and besides that ppp uses the generic SIOCPRIV ioctl so it'd
kick in for all netdevice users. We can introduce a proper handler
in one of the next patch series by adding a compat_ioctl method to
struct net_device but for now let's just kill it - parisc doesn't
compile in mainline anyway and I don't want this to block this
patchset.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <willy@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch implements generic handling of RTC_IRQP_READ32, RTC_IRQP_SET32,
RTC_EPOCH_READ32 and RTC_EPOCH_SET32 in fs/compat_ioctl.c. It's based on the
x86_64 code which needed a little massaging to be endian-clean.
parisc used COMPAT_IOCTL or generic w_long handlers for these whichce is wrong
and can't work because the ioctls encode sizeof(unsigned long) in their ioctl
number. parisc also duplicated COMPAT_IOCTL entries for other rtc ioctls
which I remove in this patch, too.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Acked-by: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The comment in compat.c is wrong, every architecture provides a
get_compat_sigevent() for the IPC compat code already.
This basically moves the x86_64 version to common code and removes all the
others.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I have heard some complaints about people not finding CONFIG_CRASH_DUMP
option and also some objections about its dependency on CONFIG_EMBEDDED.
The following patch ends that dependency. I thought of hiding it under
CONFIG_KEXEC, but CONFIG_PHYSICAL_START could also be used for some reasons
other than kexec/kdump and hence left it visible. I will also update the
documentation accordingly.
o Following patch removes the config dependency of CONFIG_PHYSICAL_START
on CONFIG_EMBEDDED. The reason being CONFIG_CRASH_DUMP option for
kdump needs CONFIG_PHYSICAL_START which makes CONFIG_CRASH_DUMP depend
on CONFIG_EMBEDDED. It is not always obvious for kdump users to choose
CONFIG_EMBEDDED.
o It also shifts the palce where this option appears, to make it closer
to kexec and kdump options.
Signed-off-by: Maneesh Soni <maneesh@in.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Moving the crash_dump.c file to arch dependent part as kmap_atomic_pfn is
specific to i386 and highmem may not exist in other archs.
- Use ioremap for x86_64 to map the previous kernel memory.
- In copy_oldmem_page(), we now directly copy to the user/kernel buffer and
avoid the unneccesary copy to a kmalloc'd page.
Signed-off-by: Rachita Kothiyal <rachita@in.ibm.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Saving the cpu registers of all cpus before booting in to the crash
kernel.
- crash_setup_regs will save the registers of the cpu on which panic has
occured. One of the concerns ppc64 folks raised is that after capturing the
register states, one should not pop the current call frame and push new one.
Hence it has been inlined. More call frames later get pushed on to stack
(machine_crash_shutdown() and machine_kexec()), but one will not want to
backtrace those.
- Not very sure about the CFI annotations. With this patch I am getting
decent backtrace with gdb. Assuming, compiler has generated enough
debugging information for crash_kexec(). Coding crash_setup_regs() in pure
assembly makes it tricky because then it can not be inlined and we don't
want to return back after capturing register states we don't want to pop
this call frame.
- Saving the non-panicing cpus registers will be done in the NMI handler
while shooting down them in machine_crash_shutdown.
- Introducing CRASH_DUMP option in Kconfig for x86_64.
Signed-off-by: Murali M Chakravarthy <muralim@in.ibm.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Vivek Goyal <vgoyal@in.ibm.com>
- Implementing the machine_crash_shutdown for x86_64 which will be called by
crash_kexec (called in case of a panic, sysrq etc.). Here we do things
similar to i386. Disable the interrupts, shootdown the cpus and shutdown
LAPIC and IOAPIC.
Changes in this version:
- As the Eric's APIC initialization patches are reverted back, reintroducing
LAPIC and IOAPIC shutdown.
- Added some comments on CPU hotplug, modified code as suggested by Andi
kleen.
Signed-off-by: Murali M Chakravarthy <muralim@in.ibm.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- elfcorehdr= specifies the location of elf core header stored by the
crashed kernel. This command line option will be passed by the kexec-tools
to capture kernel.
Changes in this version :
- Added more comments in kernel-parameters.txt and in code.
Signed-off-by: Murali M Chakravarthy <muralim@in.ibm.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Vivek Goyal <vgoyal@in.ibm.com>
- This patch introduces the memmap option for x86_64 similar to i386.
- memmap=exactmap enables setting of an exact E820 memory map, as specified
by the user.
Changes in this version:
- Used e820_end_of_ram() to find the max_pfn as suggested by Andi kleen.
- removed PFN_UP & PFN_DOWN macros
- Printing the user defined map also.
Signed-off-by: Murali M Chakravarthy <muralim@in.ibm.com>
Signed-off-by: Hariprasad Nellitheertha <nharipra@gmail.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- In case of system crash, current state of cpu registers is saved in memory
in elf note format. So far memory for storing elf notes was being allocated
statically for NR_CPUS.
- This patch introduces dynamic allocation of memory for storing elf notes.
It uses alloc_percpu() interface. This should lead to better memory usage.
- Introduced based on Andi Kleen's and Eric W. Biederman's suggestions.
- This patch also moves memory allocation for elf notes from architecture
dependent portion to architecture independent portion. Now crash_notes is
architecture independent. The whole idea is that size of memory to be
allocated per cpu (MAX_NOTE_BYTES) can be architecture dependent and
allocation of this memory can be architecture independent.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As the Crypto API now allows multiple implementations to be registered
for the same algorithm, we no longer have to play tricks with Kconfig
to select the right AES implementation.
This patch sets the driver name and priority for all the AES
implementations and removes the Kconfig conditions on the C implementation
for AES.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
A lot of crypto code needs to read/write a 32-bit/64-bit words in a
specific gender. Many of them open code them by reading/writing one
byte at a time. This patch converts all the applicable usages over
to use the standard byte order macros.
This is based on a previous patch by Denis Vlasenko.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This removes the dependency from vmlinux to install, thus avoiding the
current situation where "make install" has a nasty tendency to leave
root-turds in the working directory.
It also updates x86-64 to be in sync with i386.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Configurable 16-bit UID and friends support
This allows turning off the legacy 16 bit UID interfaces on embedded platforms.
text data bss dec hex filename
3330172 529036 190556 4049764 3dcb64 vmlinux-baseline
3328268 529040 190556 4047864 3dc3f8 vmlinux
From: Adrian Bunk <bunk@stusta.de>
UID16 was accidentially disabled for !EMBEDDED.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes it possible for boot code to use screen_info without dragging in
all of tty.h.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The ptrace_get_task_struct() helper that I added as part of the ptrace
consolidation is useful in variety of places that currently opencode it.
Switch them to the common helpers.
Add a ptrace_traceme() helper that needs to be explicitly called, and simplify
the ptrace_get_task_struct() interface. We don't need the request argument
now, and we return the task_struct directly, using ERR_PTR() for error
returns. It's a bit more code in the callers, but we have two sane routines
that do one thing well now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch moves the rtc_interrupt() prototype to rtc.h and removes the
prototypes from C files.
It also renames static rtc_interrupt() functions in
arch/arm/mach-integrator/time.c and arch/sh64/kernel/time.c to avoid compile
problems.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Paul Gortmaker <p_gortmaker@yahoo.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
____cacheline_maxaligned_in_smp is currently used to align critical structures
and avoid false sharing. It uses per-arch L1_CACHE_SHIFT_MAX and people find
L1_CACHE_SHIFT_MAX useless.
However, we have been using ____cacheline_maxaligned_in_smp to align
structures on the internode cacheline size. As per Andi's suggestion,
following patch kills ____cacheline_maxaligned_in_smp and introduces
INTERNODE_CACHE_SHIFT, which defaults to L1_CACHE_SHIFT for all arches.
Arches needing L3/Internode cacheline alignment can define
INTERNODE_CACHE_SHIFT in the arch asm/cache.h. Patch replaces
____cacheline_maxaligned_in_smp with ____cacheline_internodealigned_in_smp
With this patch, L1_CACHE_SHIFT_MAX can be killed
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sys_migrate_pages implementation using swap based page migration
This is the original API proposed by Ray Bryant in his posts during the first
half of 2005 on linux-mm@kvack.org and linux-kernel@vger.kernel.org.
The intent of sys_migrate is to migrate memory of a process. A process may
have migrated to another node. Memory was allocated optimally for the prior
context. sys_migrate_pages allows to shift the memory to the new node.
sys_migrate_pages is also useful if the processes available memory nodes have
changed through cpuset operations to manually move the processes memory. Paul
Jackson is working on an automated mechanism that will allow an automatic
migration if the cpuset of a process is changed. However, a user may decide
to manually control the migration.
This implementation is put into the policy layer since it uses concepts and
functions that are also needed for mbind and friends. The patch also provides
a do_migrate_pages function that may be useful for cpusets to automatically
move memory. sys_migrate_pages does not modify policies in contrast to Ray's
implementation.
The current code here is based on the swap based page migration capability and
thus is not able to preserve the physical layout relative to it containing
nodeset (which may be a cpuset). When direct page migration becomes available
then the implementation needs to be changed to do a isomorphic move of pages
between different nodesets. The current implementation simply evicts all
pages in source nodeset that are not in the target nodeset.
Patch supports ia64, i386 and x86_64.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Many arches make shared objects for VDSOs. Generally exclude them.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
With physical CPU hotplug, the CPU is hot removed and it should not receive
any interrupts. Disabling interrupt is much safer. This basically is what we
do in ia64 & x86.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mark some key kernel datastructures readonly. This patch was previously
posted on Jun 28th but was back then not merged because nothing was enforcing
rodata anyway.. well that changed now :)
Patch by Christoph Lameter <christoph@lameter.com> and Dave Jones
<davej@redhat.com>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
x86-64 specific parts to make the .rodata section read only
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bug fix required for the .rodata work on x86-64:
when change_page_attr() and friends need to break up a 2Mb page into 4Kb
pages, it always set the NX bit on the PMD, which causes the cpu to consider
the entire 2Mb region to be NX regardless of the actual PTE perms. This is
fine in general, with one big exception: the 2Mb page that covers the last
part of the kernel .text! The fix is to not invent a new permission for the
new PMD entry, but to just inherit the existing one minus the PSE bit.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently, we do not pass the correct start_pfn to e820_hole_size, to
calculate holes. Following patch fixes that.
The bug results in incorrect number of node_present_pages for each pgdat
and causes ugly output in /sys and probably VM inbalances.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Sighed-off-by: Shair Fultheim <shai@scalex86.org>
Sighed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the #define for ACPI_LEVEL_SENSITIVE instead of assuming
non-zero, because ACPICA 20051021 changes its value to zero.
Also, use uniform variable names:
edge_level -> triggering
active_high_low -> polarity
Signed-off-by: Len Brown <len.brown@intel.com>
Now needs to include the type 1 functions ("direct") too.
Reported by Pavel Roskin <proski@gnu.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As reported by Keith Mannthey, there are problems in populate_memnodemap()
The bug was that the compute_hash_shift() was returning 31, with incorrect
initialization of memnodemap[]
To correct the bug, we must use (1UL << shift) instead of (1 << shift) to
avoid an integer overflow, and we must check that shift < 64 to avoid an
infinite loop.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On systems that do not support the HPET legacy functions (basically the IBM
x460, but there could be others), in time_init() we accidentally fall into a
PM timer conditional and set the vxtime_hz value to the PM timer's frequency.
We then use this value with the HPET for timekeeping.
This patch (which mimics the behavior in time_init_gtod) corrects the
collision.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a register set is passed in don't try to fix up the pointer.
Noticed by Al Viro
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They report all busses as MMCONFIG capable, but it never works for the
internal devices in the CPU's builtin northbridge.
It just probes all func 0 devices on bus 0 (the internal northbridge is
currently always on bus 0) and if they are not accessible using MCFG they are
put into a special fallback bitmap.
On systems where it isn't we assume the BIOS vendor supplied correct MCFG.
Requires the earlier patch for mmconfig type1 fallback
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When there is no entry for a bus in MCFG fall back to type1. This is
especially important on K8 systems where always some devices can't be accessed
using mmconfig (in particular the builtin northbridge doesn't support it for
its own devices)
Cc: <gregkh@suse.de>
Cc: <jgarzik@pobox.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's illegal because it can sleep.
Use a two step lookup scheme instead. First look up the vm_struct, then
change the direct mapping, then finally unmap it. That's ok because nobody
can change the particular virtual address range as long as the vm_struct is
still in the global list.
Also added some LinuxDoc documentation to iounmap.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Disabling LAPIC timer isn't sufficient. In some situations, such as we
enabled NMI watchdog, there is still unexpected interrupt (such as NMI)
invoked in offline CPU. This also avoids offline CPU receives spurious
interrupt and anything similar.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: "Seth, Rohit" <rohit.seth@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Otherwise TSC->HPET fallback could see incorrect state and crash later.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When multiple probes are registered at the same address and if due to some
recursion (probe getting triggered within a probe handler), we skip calling
pre_handlers and just increment nmissed field.
The below patch make sure it walks the list for multiple probes case.
Without the below patch we get incorrect results of nmissed count for
multiple probe case.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Completed a major overhaul of the Resource Manager code -
specifically, optimizations in the area of the AML/internal
resource conversion code. The code has been optimized to
simplify and eliminate duplicated code, CPU stack use has
been decreased by optimizing function parameters and local
variables, and naming conventions across the manager have
been standardized for clarity and ease of maintenance (this
includes function, parameter, variable, and struct/typedef
names.)
All Resource Manager dispatch and information tables have
been moved to a single location for clarity and ease of
maintenance. One new file was created, named "rsinfo.c".
The ACPI return macros (return_ACPI_STATUS, etc.) have
been modified to guarantee that the argument is
not evaluated twice, making them less prone to macro
side-effects. However, since there exists the possibility
of additional stack use if a particular compiler cannot
optimize them (such as in the debug generation case),
the original macros are optionally available. Note that
some invocations of the return_VALUE macro may now cause
size mismatch warnings; the return_UINT8 and return_UINT32
macros are provided to eliminate these. (From Randy Dunlap)
Implemented a new mechanism to enable debug tracing for
individual control methods. A new external interface,
acpi_debug_trace(), is provided to enable this mechanism. The
intent is to allow the host OS to easily enable and disable
tracing for problematic control methods. This interface
can be easily exposed to a user or debugger interface if
desired. See the file psxface.c for details.
acpi_ut_callocate() will now return a valid pointer if a
length of zero is specified - a length of one is used
and a warning is issued. This matches the behavior of
acpi_ut_allocate().
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
What is the value shown in "cpu MHz" of /proc/cpuinfo when CPUs are capable of
changing frequency?
Today the answer is: It depends.
On i386:
SMP kernel - It is always the boot frequency
UP kernel - Scales with the frequency change and shows that was last set.
On x86_64:
There is one single variable cpu_khz that gets written by all the CPUs. So,
the frequency set by last CPU will be seen on /proc/cpuinfo of all the
CPUs in the system. What you see also depends on whether you have constant_tsc
capable CPU or not.
On ia64:
It is always boot time frequency of a particular CPU that gets displayed.
The patch below changes this to:
Show the last known frequency of the particular CPU, when cpufreq is present. If
cpu doesnot support changing of frequency through cpufreq, then boot frequency
will be shown. The patch affects i386, x86_64 and ia64 architectures.
Signed-off-by: Venkatesh Pallipadi<venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Linux invokes the AML _PDC method (Processor Driver Capabilities)
to tell the BIOS what features it can handle. While the ACPI
spec says nothing about the OS invoking _PDC multiple times,
doing so with changing bits seems to hopelessly confuse the BIOS
on multiple platforms up to and including crashing the system.
Factor out the _PDC invocation so Linux invokes it only once.
http://bugzilla.kernel.org/show_bug.cgi?id=5483
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix a bug in kprobes that can cause an Oops or even a crash when a return
probe is installed on one of the following functions: sys_execve,
do_execve, load_*_binary, flush_old_exec, or flush_thread. The fix is to
remove the call to kprobe_flush_task() in flush_thread(). This fix has
been tested on all architectures for which the return-probes feature has
been implemented (i386, x86_64, ppc64, ia64). Please apply.
BACKGROUND
Up to now, we have called kprobe_flush_task() under two situations: when a
task exits, and when it execs. Flushing kretprobe_instances on exit is
correct because (a) do_exit() doesn't return, and (b) one or more
return-probed functions may be active when a task calls do_exit(). Neither
is the case for sys_execve() and its callees.
Initially, the mistaken call to kprobe_flush_task() on exec was harmless
because we put the "real" return address of each active probed function
back in the stack, just to be safe, when we recycled its
kretprobe_instance. When support for ppc64 and ia64 was added, this safety
measure couldn't be employed, and was eventually dropped even for i386 and
x86_64. sys_execve() and its callees were informally blacklisted for
return probes until this fix was developed.
Acked-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix up booting with sparse mem enabled. Otherwise it would just
cause an early PANIC at boot.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is needed for large multinode IBM systems which have a sparse
APIC space in clustered mode, fully covering the available 8 bits.
The previous kernels would limit the local APIC number to 127,
which caused it to reject some of the CPUs at boot.
I increased the maximum and shrunk the apic_version array a bit
to make up for that (the version is only 8 bit, so don't need
an full int to store)
Cc: Chris McDermott <lcm@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_CHECKING covered some debugging code used in the early times
of the port. But it wasn't even SMP safe for quite some time
and the bugs it checked for seem to be gone.
This patch removes all the code to verify GS at kernel entry. There
haven't been any new bugs in this area for a long time.
Previously it also covered the sysctl for the page fault tracing.
That didn't make much sense because that code was unconditionally
compiled in. I made that a boot option now because it is typically
only useful at boot.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current x86_64 NUMA memory code is inconsequent when it comes to node
memory ranges. The exact behaviour varies depending on which config option
that is used.
setup_node_bootmem() has start and end as arguments and these are used to
calculate the size of the node like this: (end - start). This is all fine
if end is pointing to the first non-available byte. The problem is that the
current x86_64 code sometimes treats it as the last present byte and sometimes
as the first non-available byte. The result is that some configurations might
lose a page at the end of the range.
This patch tries to fix CONFIG_ACPI_NUMA, CONFIG_K8_NUMA and CONFIG_NUMA_EMU
so they all treat the end variable as the first non-available byte. This is
the same way as the single node code.
The patch is boot tested on dual x86_64 hardware with the above configurations,
but maybe the removed code is needed as some workaround?
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The logging for boot errors was turned off because it was broken
on some AMD systems. But give Intel EM64T systems a chance because they are
supposed to be correct there.
The advantage is that there is a chance to actually log uncorrected
machine checks after the reset.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On x86_64 arches, there is no way to choose ACPI_NUMA without having to choose
K8_NUMA. CONFIG_K8_NUMA is not needed for Intel EM64T NUMA boxes. It also
looks odd if you have to select ACPI_NUMA from the power management menu.
This patch fixes those oddities. Patch does the following:
1. Makes NUMA a config option like other arches
2. Makes topology detection options like K8_NUMA dependent on NUMA
3. Choosing ACPI NUMA detection can be done from the standard
"Processor type and features" menu
AK: I fixed up the dependencies and changed the help texts a bit
on top of Kiran's patch.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Keeping this function does not makes sense because it's a copied (and
buggy) copy of sys_time. The only difference is that now.tv_sec (which is
a time_t, i.e. a 64-bit long) is copied (and truncated) into a int
(32-bit).
The prototype is the same (they both take a long __user *), so let's drop
this and redirect it to sys_time (and make sure it exists by defining
__ARCH_WANT_SYS_TIME).
Only disadvantage is that the sys_stime definition is also compiled (may be
fixed if needed by adding a separate __ARCH_WANT_SYS_STIME macro, and
defining it for all arch's defining __ARCH_WANT_SYS_TIME except x86_64).
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
B stepping were the first shipping Opterons. memcpy/memset/copy_page/
clear_page had special optimized version for them. These are really
old and in the minority now and the difference to the generic versions
(using rep microcode) is not that big anyways. So just remove them.
TODO: figure out optimized versions for Intel Netburst based EM64T
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Old code could retry for 10 seconds worst time. Only try it
for one second now.
Suggested by Yinghai Lu
Cc: Yinghai.Lu@amd.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fields obtained through cpuid vector 0x1(ebx[16:23]) and
vector 0x4(eax[14:25], eax[26:31]) indicate the maximum values and might not
always be the same as what is available and what OS sees. So make sure
"siblings" and "cpu cores" values in /proc/cpuinfo reflect the values as seen
by OS instead of what cpuid instruction says. This will also fix the buggy BIOS
cases (for example where cpuid on a single core cpu says there are "2" siblings,
even when HT is disabled in the BIOS.
http://bugzilla.kernel.org/show_bug.cgi?id=4359)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When they were disabled before (e.g. after a panic) it's better
to keep them off, otherwise followon panics can happen from timer
interrupt handlers etc.
Drawback is that pageup in the console won't work anymore though.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They report 40bit, but only have 36bits of physical address space.
This caused problems with setting up the correct masks for MTRR.
CPUID workaround for steppings 0F33h(supporting x86) and 0F34h(supporting x86
and EM64T). Detail info can be found at:
http://download.intel.com/design/Xeon/specupdt/30240216.pdfhttp://download.intel.com/design/Pentium4/specupdt/30235221.pdf
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Compute the highest possible value for memnode_shift, in order to reduce
footprint of memnodemap[] to the minimum, thus making all users
(phys_to_nid(), kfree()), more cache friendly.
Before the patch :
Node 0 MemBase 0000000000000000 Limit 00000001ffffffff
Node 1 MemBase 0000000200000000 Limit 00000003ffffffff
Using 23 for the hash shift. Max adder is 3ffffffff
After the patch :
Node 0 MemBase 0000000000000000 Limit 00000001ffffffff
Node 1 MemBase 0000000200000000 Limit 00000003ffffffff
Using 33 for the hash shift.
In this case, only 2 bytes of memnodemap[] are used, instead of 2048
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows to run 64bit signal handlers in 64bit processes that run small
code snippets in compat mode.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With a NR_CPUS==128 kernel with CPU hotplug enabled we would waste 4MB
on per CPU data of all possible CPUs. The reason was that HOTPLUG
always set up possible map to NR_CPUS cpus and then we need to allocate
that much (each per CPU data is roughly ~32k now)
The underlying problem is that ACPI didn't tell us how many hotplug CPUs
the platform supports. So the old code just assumed all, which would
lead to this memory wastage.
This implements some new heuristics:
- If the BIOS specified disabled CPUs in the ACPI/mptables assume they
can be enabled later (this is bending the ACPI specification a bit,
but seems like a obvious extension)
- The user can overwrite it with a new additionals_cpus=NUM option
- Otherwise use half of the available CPUs or 2, whatever is more.
Cc: ashok.raj@intel.com
Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Minor victory on the continuous quest against all stray extern.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jon Mason