We must check the bustype before using the host_pci pointer.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes some gcc warnings for switch statements.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Neil Horman <nhorman@txudriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Over time, a whole bunch of drivers have come up
with their own scheme to delay the configure_filter
operation to a workqueue. To be able to simplify
things, allow configure_filter to sleep, and add
a new prepare_multicast callback that drivers that
need the multicast address list implement. This new
callback must be atomic, but most drivers either
don't care or just calculate a hash which can be
done atomically and then uploaded to the hardware
non-atomically.
A cursory look suggests that at76c50x-usb, ar9170,
mwl8k (which is actually very broken now), rt2x00,
wl1251, wl1271 and zd1211 should make use of this
new capability.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As shown in http://thread.gmane.org/gmane.linux.kernel.wireless.general/36497,
mac80211 has a bug that allows a call to the TX routine after the queues have
been stopped. This situation will only occur under extreme stress. Although
b43legacy does not crash when this condition occurs, it does generate a WARN_ON
and also logs a queue overrun message. This patch recognizes b43legacy is not
at fault and logs a message only when the most verbose debugging mode is
enabled. In the unlikely event that the queue is not stopped when the DMA
queue becomes full, then a warning is issued.
This patch is based on the one used by b43.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 workqueue exists to enable mac80211 and drivers
to queue their own work on a single threaded workqueue. mac80211
takes care to flush the workqueue during suspend but we never
really had requirements on drivers for how they should use
the workqueue in consideration for suspend.
We extend mac80211 to document how the mac80211 workqueue should
be used, how it should not be used and finally move raw access to
the workqueue to mac80211 only. Drivers and mac80211 use helpers
to queue work onto the mac80211 workqueue:
* ieee80211_queue_work()
* ieee80211_queue_delayed_work()
These helpers will now warn if mac80211 already completed its
suspend cycle and someone is trying to queue work. mac80211
flushes the mac80211 workqueue prior to suspend a few times,
but we haven't taken the care to ensure drivers won't add more
work after suspend. To help with this we add a warning when
someone tries to add work and mac80211 already completed the
suspend cycle.
Drivers should ensure they cancel any work or delayed work
in the mac80211 stop() callback.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Within mac80211, we often need to copy the rx status into
skb->cb. This is wasteful, as drivers could be building it
in there to start with. This patch changes the API so that
drivers are expected to pass the RX status in skb->cb, now
accessible as IEEE80211_SKB_RXCB(skb). It also updates all
drivers to pass the rx status in there, but only by making
them memcpy() it into place before the call to the receive
function (ieee80211_rx(_irqsafe)). Each driver can now be
optimised on its own schedule.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix condition in which radio LED did not initialize correctly, and remove
4 compilation warnings.
After the recent changes in rfkill, the radio LED used by b43/b43legacy
did not always initialize correctly.
Both b43 and b43legacy used the deprecated variable radio_enabled in
struct ieee80211_conf.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This ports the b43/legacy rfkill code to the new API offered
by cfg80211 and thus removes a lot of useless stuff.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch completely rewrites the rfkill core to address
the following deficiencies:
* all rfkill drivers need to implement polling where necessary
rather than having one central implementation
* updating the rfkill state cannot be done from arbitrary
contexts, forcing drivers to use schedule_work and requiring
lots of code
* rfkill drivers need to keep track of soft/hard blocked
internally -- the core should do this
* the rfkill API has many unexpected quirks, for example being
asymmetric wrt. alloc/free and register/unregister
* rfkill can call back into a driver from within a function the
driver called -- this is prone to deadlocks and generally
should be avoided
* rfkill-input pointlessly is a separate module
* drivers need to #ifdef rfkill functions (unless they want to
depend on or select RFKILL) -- rfkill should provide inlines
that do nothing if it isn't compiled in
* the rfkill structure is not opaque -- drivers need to initialise
it correctly (lots of sanity checking code required) -- instead
force drivers to pass the right variables to rfkill_alloc()
* the documentation is hard to read because it always assumes the
reader is completely clueless and contains way TOO MANY CAPS
* the rfkill code needlessly uses a lot of locks and atomic
operations in locked sections
* fix LED trigger to actually change the LED when the radio state
changes -- this wasn't done before
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> [thinkpad]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Process beacon change even if the BSSID doesn't
change at the same time. Also fix what I think
is a small locking error in b43legacy, there's
a spin_unlock_irqrestore that looks out of place.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes unnecessary MMIO accesses in the interrupt hotpath. The
patch by Michael Buesch for b43 has been ported to b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The config_interface method is a little strange, it contains the
BSSID and beacon updates, while bss_info_changed contains most
other BSS information for each interface. This patch removes
config_interface and rolls all the information it previously
passed to drivers into bss_info_changed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently have two beacon interval configuration knobs:
hw.conf.beacon_int and vif.bss_info.beacon_int. This is
rather confusing, even though the former is used when we
beacon ourselves and the latter when we are associated to
an AP.
This just deprecates the hw.conf.beacon_int setting in favour
of always using vif.bss_info.beacon_int. Since it touches all
the beaconing IBSS code anyway, we can also add support for
the cfg80211 IBSS beacon interval configuration easily.
NOTE: The hw.conf.beacon_int setting is retained for now due
to drivers still using it -- I couldn't untangle all
drivers, some are updated in this patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ports commit c97a4ccc1f "b43: Fix beacon BH update" to
b43legacy. It fixes beacon updating in the bottomhalf. In case the device
is busy, we will defer to later in the IRQ handler.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Tested-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ports the beaconing fixes from commit a82d992261 "b43: Beaconing
fixes" to b43legacy. Basically it prevents the card from triggering the beacon
IRQ over and over again.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Tested-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Auto-depend on HW_RANDOM, rather than "select"ing it.
This way the user has the choice to enable or disable HWRNG support.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Almost all drivers do not support user_claim, so remove it
completely and always report -EOPNOTSUPP to userspace. Since
userspace cannot really drive rfkill _anyway_ (due to the
odd restrictions imposed by the documentation) having this
code is just pointless.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace all DMA_30BIT_MASK macro with DMA_BIT_MASK(30)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixed led device naming for the b43legacy driver. Due to the
documentation of the led subsystem/class the naming should be
"devicename:colour:function" while not applying sections
should be left blank.
This should lead to e.g. "b43legacy-%s::rx" instead of
"b43legacy-%s:rx".
Signed-off-by: Danny Kukawka <dkukawka@suse.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the standards only define 12 legacy rates, 32 is certainly
a sane upper limit and we don't need to use u64 everywhere. Add
sanity checking that no more than 32 rates are registered and
change the variables to u32 throughout.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/b43legacy/main.c: In function ‘b43legacy_op_dev_config’:
drivers/net/wireless/b43legacy/main.c:2468: warning: ‘up_dev’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements proper short slot handling and adds code to
program the hardware for the correct response rates derived
from the basic rate set for the current BSS.
(port from b43)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SSID programmed into the device is used by the ucode only
to reply to probe requests, a functionality we disable anyway
because it doesn't fit with the mac80211/hostapd programming
model. Therefore, it isn't useful to program the SSID into
device.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So after the previous changes we were still unhappy with how
convoluted the API is and decided to make things simpler for
everybody. This completely changes the rate control API, now
taking into account 802.11n with MCS rates and more control,
most drivers don't support that though.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having a separate callback, use the HW config callback
with a new flag to change retry limits.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes mac80211 notify the driver which configuration
actually changed, e.g. channel etc.
No driver changes, this is just plumbing, driver authors are
expected to act on this if they want to.
Also remove the HW CONFIG debug printk, it's incorrect, often
we configure something else.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adjusts the rate control API to allow multi-rate retry
if supported by the driver. The ieee80211_hw struct specifies how
many alternate rate selections the driver supports.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Free up 2 bytes in skb->cb to be used for multi-rate retry later.
Move iv_len and icv_len initialization into key alloc.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit bc19d6e0b7, which as
Larry Finger reports causes the radio LED on his system to no longer
respond to rfkill switch events.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Requested-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes mac80211 to share some more data about
stations with drivers. Should help iwlwifi and ath9k when
they get around to updating, and might also help with
implementing rate control algorithms without internals.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's really no reason for mac80211 to be using its
own interface type defines. Use the nl80211 types and
simplify the configuration code a bit: there's no need
to translate them any more now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent changes in the specifications have improved the performance
of the BCM4306/2 devices that use b43legacy as the driver. These
"errors" in the specs have been present from the very first implementation
of bcm43xx.
Signed-off-by: Ehud Gavron <gavron@wetwork.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A coding error present since b43legacy was incorporated into the
kernel has prevented the driver from using the rate-setting mechanism
of mac80211. The driver has been forced to remain at a 1 Mb/s rate.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org> [2.6.26], [2.6.25]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is obviously good for userspace to know up front which
interface modes a given piece of hardware might support (even
if adding such an interface might fail later because of
concurrency issues), so let's make cfg80211 aware of that.
For good measure, disallow adding interfaces in all other
modes so drivers don't forget to announce support for one mode
when they add it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/net/wireless/b43legacy/main.c
drivers/net/wireless/iwlwifi/iwl-3945-led.c
drivers/net/wireless/iwlwifi/iwl-led.c
drivers/net/wireless/iwlwifi/iwl-rfkill.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes mac80211 to not use the skb->cb over the queue step
from virtual interfaces to the master. The patch also, for now,
disables aggregation because that would still require requeuing,
will fix that in a separate patch. There are two other places (software
requeue and powersaving stations) where requeue can happen, but that is
not currently used by any drivers/not possible to use respectively.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mutex is released on a successful return, so it would seem that it
should be released on an error return as well.
The semantic patch finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression l;
@@
mutex_lock(l);
... when != mutex_unlock(l)
when any
when strict
(
if (...) { ... when != mutex_unlock(l)
+ mutex_unlock(l);
return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I forgot this in the previous patch that made it unused.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes mac80211 assign proper sequence numbers to
QoS-data frames. It also removes the old sequence number code
because we noticed that only the driver or hardware can assign
sequence numbers to non-QoS-data and especially management
frames in a race-free manner because beacons aren't passed
through mac80211's TX path.
This patch also adds temporary code to the rt2x00 drivers to
not break them completely, that code will have to be reworked
for proper sequence numbers on beacons.
It also moves sequence number assignment down in the TX path
so no sequence numbers are assigned to frames that are dropped.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes mac80211's beacon configuration handling
to never pass skbs to the driver directly but rather always
require the driver to use ieee80211_beacon_get(). Additionally,
it introduces "change flags" on the config_interface() call
to enable drivers to figure out what is changing. Finally, it
removes the beacon_update() driver callback in favour of
having IBSS beacon delivered by ieee80211_beacon_get() as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The gcc 3.4 fork used to compile the MN10300 port emits unwanted
__ucmpdi2() calls for switch statements that use a 64bit value.
This patch removes such a switch from b43legacy, and makes the code
more like that used in b43. Thanks to Adrian Bunk <bunk@kernel.org>
for reporting the problem.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch