Direct access to USB host controller registers is considered to be not
portable, and is usually a bad sign for poorly abstracted interface.
Introduce .flags and .power_on_delay to "struct pxaohci_platform_data"
so that most platforms don't bother to write their own .init/.exit()
sequences.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There will always be only one pwm-backlight on this device.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These were only needed for hardcoded flash partition tables, which were
never submitted. It is better to have the bootloader pass the partition
table to the kernel instead.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The pin configuration array is only used during board init.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
magician has a GPIO that modifies the brightness level additionally to
the PWM duty value. This patch makes use of the pwm_bl notify callback
to present userspace with a single brightness scale.
This gets rid of the pxa_set_cken calls and direct PWM register access.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The power manager and core clock registers aren't present in PXA3
CPUs. Move them out of pxa-regs.h into pxa2xx-regs.h, and include
pxa2xx-regs.h where necessary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Platform data must not be marked with __devinit. Even __devinitdata
would be wrong as the platform driver can be compiled as a module.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some input pin configuration that is not handled by drivers. This should
serve mostly as documentation.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Registers some GPIOs used in magician.c with the GPIO API.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Although the GPIO alternate functions should be correctly set
by the bootloader, configure them here to be sure.
To save power, FFUART/BTUART/STUART are left unconfigured (output, low)
until they are needed by pxaficp or the magician GSM chipset driver.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch enables LEDs and the 1-wire bus (connected to
a DS2760 battery monitor) on the magician.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All magician devices I've encountered so far have featured the Toppoly
TD028STEB1 display, so the Samsung LTP280QV support is untested.
The power-on sequence is not correct because pxafb doesn't yet support
enabling the LCD controller in the middle of the it.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This enables rootfs on StrataFlash if the bootloader supplies the
partition list.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
needed for power management (audio, BT, charging, GSM, LCD, SD), GSM, flash and SD operation and audio routing.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since recent PXA changes the (non-power-)I2C bus has to be explicitly
enabled from board initialisation code.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This includes irda, gpio keys, pxafb, backlight, ohci and flash
(read-only).
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eric Miao