The Versatile Express uses a special configuration controller
deeply embedded in the system motherboard FPGA to multiplex the
two to three (!) display controller instances out to the single
SiI9022 bridge.
Set up an extra file with the logic to probe to the FPGA mux
register on the system controller bus, then parse the device
tree to see if there is a CLCD or HDLCD instance on the core
tile (also known as the daughterboard) by looking in the
root of the device tree for compatible nodes.
- If there is a HDLCD on the core tile, and there is a driver
for it, we exit probe and deactivate the motherboard CLCD.
We do not touch the DVI mux in this case, to make sure we
don't break HDLCD.
- If there is a CLCD on both the motherboard and the core tile
(only the CA9 has this) the core tile CLCD takes precedence
and get muxed to the DVI connector.
- Only if there is no working graphics on the core tile, the
motherboard CLCD is probed and muxed to the DVI connector.
Core tile graphics should always take precedence as it can
address all memory and is also faster, however the motherboard
CLCD is good to have around for diagnostics and testing.
It is possible to test the motherboard CLCD by setting the
status = "disabled" property on the core tile CLCD or
HDLCD.
Scale down the Versatile Express to 16BPP so we can support a
1024x768 display despite the bus bandwidth restrictions on this
platform. (The motherboard CLCD supports slightly lower
resolution.)
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Acked-by: Eric Anholt <eric@anholt.net>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180502134719.8388-1-linus.walleij@linaro.org
We were previously selecting 1024x768 and 32BPP as the default
set-up for the PL111 consumers.
This does not work on elder systems: the device tree bindings
support a property "max-memory-bandwidth" in bytes/second that
states that if you exceed this the memory bus will saturate.
The result is flickering and unstable images.
Parse the "max-memory-bandwidth" and respect it when
intializing the driver. On the RealView PB11MP, Versatile and
Integrator/CP we get a nice console as default with this code.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307215819.15814-1-linus.walleij@linaro.org
We want to cut down the default bpp to 16 on the RealView so
we can have a 1024x768 framebuffer console by default. The
memory bandwidth limitations makes this not work with the
PL111 default of 32bpp.
This builds on top of the earlier patches making the
framebuffer default bpp a per-variant variable.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302090948.6399-4-linus.walleij@linaro.org
DRM_DUMB_VGA_DAC is a user-visible symbol. Selecting it can cause unmet
direct dependencies such as this (on i386, randconfig):
warning: (DRM_PL111) selects DRM_DUMB_VGA_DAC which has unmet direct dependencies (HAS_IOMEM && DRM && DRM_BRIDGE && OF)
This is because DRM_DUMB_VGA_DAC depends on OF while DRM_PL111 does not.
It does indirectly depend on OF via the ARM and ARM64 dependencies, but
since it can also be enabled under COMPILE_TEST, randconfig can find a
case where DRM_PL111 is selected without pulling in OF and not meeting
the dependency for DRM_DUMB_VGA_DAC.
Since select is "heavy handed", DRM_DUMB_VGA_DAC is going to be enabled
regardless of the above warning and causes the following build error:
../drivers/gpu/drm/bridge/dumb-vga-dac.c: In function 'dumb_vga_probe':
../drivers/gpu/drm/bridge/dumb-vga-dac.c:207:13: error: 'struct drm_bridge' has no member named 'of_node'
vga->bridge.of_node = pdev->dev.of_node;
See Documentation/kbuild/kconfig-language.txt, "reverse dependencies".
Fixes: 49f81d80ab ("drm/pl111: Support handling bridge timings")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Archit Taneja <archit@cradlewise.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220102903.27787-1-thierry.reding@gmail.com
Do not use deprecated drm_driver.{enable|disable)_vblank callbacks,
but use drm_simple_kms_helpe's pipe callbacks instead.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Cc: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1518425574-32671-5-git-send-email-andr2000@gmail.com
The Versatile PL110 implementations use multiple endpoints:
from the PL111 port, the lines are routed through a PLD,
and from there forked so the same lines go to a VGA DAC and
an external TFT panel connector. This is discrete wireing
so there is no way to turn of one output, i.e. this is
really two endpoints, not two ports.
We model this with multiple endpoints, so we need to loop
over the available endpoints, check for panel or bridge on
each and accumulate the result before continuing.
The code already will give the panel preference over the
bridge, if present, so the output will be sent to the panel
if both a panel and a bridge is present on two endpoints
of the same port.
If they all return -EPROBE_DEFER we return -EPROBE_DEFER
as well.
If just one endpoint is present on the port, the behaviour
is the same as before.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180206093540.8147-5-linus.walleij@linaro.org
The early Integrator CLCD synthesized in the Integrator CP and
IM-PD1 FPGAs are broken: their vertical and next base interrupts
are not functional. Support these variants by simply disabling
the use of the vblank interrupt on these variants.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180206093540.8147-4-linus.walleij@linaro.org
The early Integrator CLCD synthesized in the Integrator CP and
IM-PD1 FPGAs are broken: their clock dividers do not work
properly. Support disabling the clock divider and drive the
clock directly from the parent under these circumstances.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180206093540.8147-3-linus.walleij@linaro.org
The ARM Versatile series can do RGB/BGR565 with an external
"PLD" (Programmable Logical Device). However the CLCD does not
have control bits for this, so it needs to be set into the
ordinary 16BPP mode, then the RGB/BGR565 handling of the pixel
data is handled by configuring the PLD through the external
register.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180206093540.8147-2-linus.walleij@linaro.org
With a bit of refactoring we can contain the variant data for
the strange PL110 versions that is feature-incomplete PL110 for
the ARM Integrator/CP and somewhere inbetween PL110 and PL111
for the ARM Versatile AB and Versatile PB.
We also accomodate for the custom duct-taped RGB565/BGR565 support
in the Versatile variant.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180206093540.8147-1-linus.walleij@linaro.org
If the bridge has a too strict setup time for the incoming
signals, we may not be fast enough and then we need to
compensate by outputting the signal on the inverse clock
edge so it is for sure stable when the bridge samples it.
Since bridges in difference to panels does not expose their
connectors, make the connector optional in the display
setup code.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180112074854.9560-4-linus.walleij@linaro.org
Use drm_fb_cma_fbdev_init() and drm_fb_cma_fbdev_fini() which relies on
the fact that drm_device holds a pointer to the drm_fb_helper structure.
This means that the driver doesn't have to keep track of that.
Also use the drm_fb_helper functions directly.
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20171115142001.45358-11-noralf@tronnes.org
-----BEGIN PGP SIGNATURE-----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=xVV2
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.15.
Core:
- Atomic object lifetime fixes
- Atomic iterator improvements
- Sparse/smatch fixes
- Legacy kms ioctls to be interruptible
- EDID override improvements
- fb/gem helper cleanups
- Simple outreachy patches
- Documentation improvements
- Fix dma-buf rcu races
- DRM mode object leasing for improving VR use cases.
- vgaarb improvements for non-x86 platforms.
New driver:
- tve200: Faraday Technology TVE200 block.
This "TV Encoder" encodes a ITU-T BT.656 stream and can be found in
the StorLink SL3516 (later Cortina Systems CS3516) as well as the
Grain Media GM8180.
New bridges:
- SiI9234 support
New panels:
- S6E63J0X03, OTM8009A, Seiko 43WVF1G, 7" rpi touch panel, Toshiba
LT089AC19000, Innolux AT043TN24
i915:
- Remove Coffeelake from alpha support
- Cannonlake workarounds
- Infoframe refactoring for DisplayPort
- VBT updates
- DisplayPort vswing/emph/buffer translation refactoring
- CCS fixes
- Restore GPU clock boost on missed vblanks
- Scatter list updates for userptr allocations
- Gen9+ transition watermarks
- Display IPC (Isochronous Priority Control)
- Private PAT management
- GVT: improved error handling and pci config sanitizing
- Execlist refactoring
- Transparent Huge Page support
- User defined priorities support
- HuC/GuC firmware refactoring
- DP MST fixes
- eDP power sequencing fixes
- Use RCU instead of stop_machine
- PSR state tracking support
- Eviction fixes
- BDW DP aux channel timeout fixes
- LSPCON fixes
- Cannonlake PLL fixes
amdgpu:
- Per VM BO support
- Powerplay cleanups
- CI powerplay support
- PASID mgr for kfd
- SR-IOV fixes
- initial GPU reset for vega10
- Prime mmap support
- TTM updates
- Clock query interface for Raven
- Fence to handle ioctl
- UVD encode ring support on Polaris
- Transparent huge page DMA support
- Compute LRU pipe tweaks
- BO flag to allow buffers to opt out of implicit sync
- CTX priority setting API
- VRAM lost infrastructure plumbing
qxl:
- fix flicker since atomic rework
amdkfd:
- Further improvements from internal AMD tree
- Usermode events
- Drop radeon support
nouveau:
- Pascal temperature sensor support
- Improved BAR2 handling
- MMU rework to support Pascal MMU
exynos:
- Improved HDMI/mixer support
- HDMI audio interface support
tegra:
- Prep work for tegra186
- Cleanup/fixes
msm:
- Preemption support for a5xx
- Display fixes for 8x96 (snapdragon 820)
- Async cursor plane fixes
- FW loading rework
- GPU debugging improvements
vc4:
- Prep for DSI panels
- fix T-format tiling scanout
- New madvise ioctl
Rockchip:
- LVDS support
omapdrm:
- omap4 HDMI CEC support
etnaviv:
- GPU performance counters groundwork
sun4i:
- refactor driver load + TCON backend
- HDMI improvements
- A31 support
- Misc fixes
udl:
- Probe/EDID read fixes.
tilcdc:
- Misc fixes.
pl111:
- Support more variants
adv7511:
- Improve EDID handling.
- HDMI CEC support
sii8620:
- Add remote control support"
* tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux: (1480 commits)
drm/rockchip: analogix_dp: Use mutex rather than spinlock
drm/mode_object: fix documentation for object lookups.
drm/i915: Reorder context-close to avoid calling i915_vma_close() under RCU
drm/i915: Move init_clock_gating() back to where it was
drm/i915: Prune the reservation shared fence array
drm/i915: Idle the GPU before shinking everything
drm/i915: Lock llist_del_first() vs llist_del_all()
drm/i915: Calculate ironlake intermediate watermarks correctly, v2.
drm/i915: Disable lazy PPGTT page table optimization for vGPU
drm/i915/execlists: Remove the priority "optimisation"
drm/i915: Filter out spurious execlists context-switch interrupts
drm/amdgpu: use irq-safe lock for kiq->ring_lock
drm/amdgpu: bypass lru touch for KIQ ring submission
drm/amdgpu: Potential uninitialized variable in amdgpu_vm_update_directories()
drm/amdgpu: potential uninitialized variable in amdgpu_vce_ring_parse_cs()
drm/amd/powerplay: initialize a variable before using it
drm/amd/powerplay: suppress KASAN out of bounds warning in vega10_populate_all_memory_levels
drm/amd/amdgpu: fix evicted VRAM bo adjudgement condition
drm/vblank: Tune drm_crtc_accurate_vblank_count() WARN down to a debug
drm/rockchip: add CONFIG_OF dependency for lvds
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ARM reference designs in the Versatile family: Integrator,
Versatile and RealView can make use of the new DRM driver as well.
We just need to create a bit of platform-specific code for them
that we isolate to its own file.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908124709.4758-7-linus.walleij@linaro.org
The old codebase has a delay between enabling and powering up the
PL11x.
According to the manual for PL110, ARM DDI 0161E page 1-5 and
the PL111 manual ARM DDI 0293C page 1-6, the power sequence should
be such that once Vdd is stable (which we assume it is at boot)
LCDEN is enabled first and then CLPOWER should be enabled
"after the signals have stabilized" and this is said to
be display-dependent. The old codebase uses 20ms.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908124709.4758-5-linus.walleij@linaro.org
We detect and enable the use of the PL110 variant, an earlier
incarnation of PL111. The only real difference is that the
control and interrupt enable registers have swapped place.
The Versatile AB and Versatile PB have a variant inbetween
PL110 and PL111, it is PL110 but they have already swapped the
two registers so those two need a bit of special handling.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908124709.4758-4-linus.walleij@linaro.org
This replaces the custom connector in the PL111 with the
panel bridge helper.
This works nicely for all standard panels, but since there
are several PL11x-based systems that will need to use the dumb
VGA connector bridge we use drm_of_find_panel_or_bridge()
and make some headroom for dealing with bridges that are
not panels as well, and drop a TODO in the code.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908124709.4758-3-linus.walleij@linaro.org
Make these structures const as they are only stored in the funcs field
of a drm_mode_config structure which is of type const.
Done using Coccinelle:
@match disable optional_qualifier@
identifier s;
@@
static struct drm_mode_config_funcs s = {...};
@ref@
position p;
identifier match.s;
@@
s@p
@good1@
identifier y;
position ref.p;
identifier match.s;
@@
struct drm_mode_config y = {...,.funcs=&s@p,...};
@good2@
struct drm_mode_config y;
identifier match.s;
position ref.p;
@@
y.funcs = &s@p
@bad depends on !good1 && !good2@
position ref.p;
identifier match.s;
@@
s@p
@depends on forall !bad disable optional_qualifier@
identifier match.s;
@@
static
+ const
struct drm_mode_config_funcs s;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1502204751-16525-1-git-send-email-bhumirks@gmail.com
It's dead code, the core handles all this directly now.
The only special case is nouveau and tda988x which used one function
for both legacy modeset code and -nv50 atomic world instead of 2
vtables. But amounts to exactly the same.
v2: Rebase over the panel/brideg refactorings in stm/ltdc.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Peter Senna Tschudin <peter.senna@collabora.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Yakir Yang <kuankuan.y@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Romain Perier <romain.perier@collabora.com>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Hai Li <hali@codeaurora.org>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-tegra@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Cc: zain wang <wzz@rock-chips.com>
Cc: Baoyou Xie <baoyou.xie@linaro.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-8-daniel.vetter@ffwll.ch
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Philippe Cornu <philippe.cornu@st.com> (on stm)
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
This is the plumbing for supporting fb modifiers on planes. Modifiers
have already been introduced to some extent, but this series will extend
this to allow querying modifiers per plane. Based on this, the client to
enable optimal modifications for framebuffers.
This patch simply allows the DRM drivers to initialize their list of
supported modifiers upon initializing the plane.
v2: A minor addition from Daniel
v3:
* Updated commit message
* s/INVALID/DRM_FORMAT_MOD_INVALID (Liviu)
* Remove some excess newlines (Liviu)
* Update comment for > 64 modifiers (Liviu)
v4: Minor comment adjustments (Liviu)
v5: Some new platforms added due to rebase
v6: Add some missed plane inits (or maybe they're new - who knows at
this point) (Daniel)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Daniel Stone <daniels@collabora.com> (v2)
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Stone <daniels@collabora.com>
If src_x/y were nonzero, we failed to shift them down by 16 to get the
pixel offset. The recent CMA helper function gets it right.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: bed41005e6 ("drm/pl111: Initial drm/kms driver for pl111")
Reported-by: Mircea Carausu <mircea.carausu@broadcom.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170603015733.13266-1-eric@anholt.net
Reviewed-by: Sean Paul <seanpaul@chromium.org>
The driver is written in a way to enable compile-testing without CONFIG_ARM_AMBA,
but it just causes needless warnings:
drivers/gpu/drm/pl111/pl111_drv.c:149:26: error: 'pl111_drm_driver' defined but not used [-Werror=unused-variable]
drivers/gpu/drm/pl111/pl111_drv.c:81:12: error: 'pl111_modeset_init' defined but not used [-Werror=unused-function]
This unhides the probe/remove functions again and just leaves the driver
object as unused when CONFIG_ARM_AMBA is disabled, with a __maybe_unused
annotation to shut up the warning.
Fixes: bed41005e6 ("drm/pl111: Initial drm/kms driver for pl111")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170524155020.1777369-1-arnd@arndb.de
When DRM_PANEL is disabled, we get a link error for pl111:
drivers/gpu/built-in.o: In function `pl111_connector_destroy':
pl111_connector.c:(.text+0x3487e6): undefined reference to `drm_panel_detach'
For some reason this only appears in the latest linux-next
although the driver appears to have used the symbol for a few
weeks already. The solution however is simple enough, we just
need to add a 'select' statement.
Fixes: bed41005e6 ("drm/pl111: Initial drm/kms driver for pl111")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170530092224.1204037-1-arnd@arndb.de
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: bed41005e6 ("drm/pl111: Initial drm/kms driver for pl111")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170521010152.6186-1-weiyj.lk@gmail.com
While debugging an X11 display failure, I wanted to see where we were
actually scanning out from. This is probably generally useful to
others that might be working on this device.
v2: Fix uint32_t sparse warning.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170518005640.10310-1-eric@anholt.net
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> (v1)
structure mode_config_funcs can be made static as it does not need to be
in global scope. Fixes sparse warning:
warning: symbol 'mode_config_funcs' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170519111018.19641-1-colin.king@canonical.com
structure pl111_display_funcs can be made static as it does not need to be
in global scope. Fixes sparse warning:
"warning: symbol 'pl111_display_funcs' was not declared. Should it
be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170519110203.19417-1-colin.king@canonical.com
This is required for the panel to work on bcm911360, where CLCDCLK is
the fixed 200Mhz AXI41 clock. The rate set is still passed up to the
CLCDCLK, for platforms that have a settable rate on that one.
v2: Set SET_RATE_PARENT (caught by Linus Walleij), depend on
COMMON_CLK.
v3: Mark the clk_ops static (caught by Stephen).
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170508193348.30236-1-eric@anholt.net
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
This is a modesetting driver for the pl111 CLCD display controller
found on various ARM platforms such as the Versatile Express. The
driver has only been tested on the bcm911360_entphn platform so far,
with PRIME-based buffer sharing between vc4 and clcd.
It reuses the existing devicetree binding, while not using quite as
many of its properties as the fbdev driver does (those are left for
future work).
v2: Nearly complete rewrite by anholt, cutting 2/3 of the code thanks
to DRM core's excellent new helpers.
v3: Don't match pl110 any more, don't attach if we don't have a DRM
panel, use DRM_GEM_CMA_FOPS, update MAINTAINERS, use the simple
display helper, use drm_gem_cma_dumb_create (same as our wrapper).
v4: Change the driver's .name to not clash with fbdev in sysfs, drop
platform alias, drop redundant "drm" in DRM driver name, hook up
.prepare_fb to the CMA helper so that DMA fences should work.
v5: Move register definitions inside the driver directory, fix build
in COMPILE_TEST and !AMBA mode.
v6: Drop TIM2_CLKSEL for now to be consistent with existing DT
bindings, switch back to external register definitions.
Signed-off-by: Tom Cooksey <tom.cooksey@arm.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> (v5)
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170413031746.12921-2-eric@anholt.net
Linus Walleij