Some vendors need newer UniPro version to decide if some features can be
enabled or not.
Simply add missing enums for the latest UniPro versions.
Link: https://lore.kernel.org/r/20201029115750.24391-6-stanley.chu@mediatek.com
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
PA Layer issues a LINERESET to the PHY at the recovery step in the Power
Mode change operation. If it happens during auto or manual hibern8 enter,
even if hibern8 enter succeeds, UFS power mode shall be set to PWM-G1 mode
and kept in that mode after exit from hibern8, leading to bad performance.
Handle the LINERESET in the eh_work by restoring power mode to HS mode
after all pending reqs and tasks are cleared from doorbell.
Link: https://lore.kernel.org/r/1598321228-21093-3-git-send-email-cang@codeaurora.org
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch introduces Exynos UFS host controller driver which mainly
handles vendor-specific operations including link startup, power mode
change and hibernation/unhibernation.
[robot: drivers/scsi/ufs/ufs-exynos.c:931:8-10:
WARNING: possible condition with no effect (if == else)
]
Link: https://lore.kernel.org/r/20200528011658.71590-10-alim.akhtar@samsung.com
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Tested-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Reviewed-by: Kiwoong Kim <kwmad.kim@samsung.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ADAPT is added specifically for HS Gear4 mode only. Select INITIAL ADAPT
before power mode change to G4 and select NO ADAPT before switch to non-G4
modes.
[mkp: fixed typo in header file]
Link: https://lore.kernel.org/r/1581485910-8307-3-git-send-email-cang@codeaurora.org
Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During power mode change, PACP_PWR_Req frame sends PAPowerModeUserData
parameters (and they are considered valid by device if Flags[4] -
UserDataValid bit is set in the same frame). Currently we don't set these
PAPowerModeUserData parameters and hardware always sets UserDataValid bit
which would clear all the DL layer timeout values of the peer device after
the power mode change.
This change sets the PAPowerModeUserData[0..5] to UniPro specification
recommended default values, in addition we are also setting the relevant
DME_LOCAL_* timer attributes as required by UFS HCI specification.
Link: https://lore.kernel.org/r/0101016ed3d688a4-cfaeb1c9-238b-46c4-9c89-d48c410ba325-000000@us-west-2.amazonses.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix RX_TERMINATION_FORCE_ENABLE define value from 0x0089 to 0x00A9
according to MIPI Alliance MPHY specification.
Fixes: e785060ea3 ("ufs: definitions for phy interface")
Signed-off-by: Pedro Sousa <sousa@synopsys.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS devices require host PA_TACTIVATE to be higher than
device PA_TACTIVATE otherwise it may get stuck during hibern8 sequence.
This change allows this by using quirk.
Reviewed-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add unipro attributes.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS devices (and may be host) have issues if LCC is
enabled. So we are setting PA_Local_TX_LCC_Enable to 0
before link startup which will make sure that both host
and device TX LCC are disabled once link startup is
completed.
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Optimal values of local UniPro parameters like PA_Hibern8Time &
PA_TActivate can help reduce the hibern8 exit latency. If both host and
device supports UniPro ver1.6 or later, these parameters will be
automatically tuned during link startup itself. But if either host or
device doesn't support UniPro ver 1.6 or later, we have to manually
tune them. But to keep manual tuning logic simple, we will only do
manual tuning if local unipro version doesn't support ver1.6 or later.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Adding some of the definitions missing in unipro.h, including power
enumeration.
- Read Modify Write Line helper function
- Indication for the type of suspend
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
UIC attributes can be set with using DME_SET command for
power mode change. For configuration the link capability
attributes are used, which is updated after successful
link startup.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Setting PA_PWRMode using DME_SET triggers the power mode
change. And then the result will be given by the HCS.UPMCRS.
This operation should be done atomically.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Tested-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Stanley Chu