In ntb_netdev_open, when ntb_transport_rx_enqueue fails the skb that was
attempting to be enqueued is not freed. Free this skb on the
ntb_transport_rx_enqueue error.
Signed-off-by: Jon Mason <jon.mason@intel.com>
If list_for_each_entry exits without finding the ntb_device, the dev
pointer will not be NULL. Thus the check will never be true and the
code will not exit when it should. Correct this by adding a bool to
determine when the device is found, otherwise exit in good fashion.
Signed-off-by: Jon Mason <jon.mason@intel.com>
The commit 1edb9ca69e ("net: sxgbe: add basic framework for
Samsung 10Gb ethernet driver") added support for Samsung 10Gb
ethernet driver(sxgbe) with a minor issue of including linux/io.h
header twice in sxgbe_dma.c file. Fix the duplicate #include by
deleting the top one so that all the rest good #include headers
would be preserved in the alphabetical order.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Cc: Byungho An <bh74.an@samsung.com>
Cc: Girish K S <ks.giri@samsung.com>
Cc: Siva Reddy Kallam <siva.kallam@samsung.com>
Cc: Vipul Pandya <vipul.pandya@samsung.com>
Acked-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a "%" after pending_idx instead of ":".
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
version.h inclusion is not necessary as detected by versioncheck.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ioaddr local variable is assigned to but never used in the
smc911x_rx_dma_irq() function, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bond_open is not setting the inactive flag correctly for some modes (alb and
tlb), resulting in error behavior if the bond has been administratively set
down and then back up. This effect should not occur when slaves are added while
the bond is up; it's something that only happens after a down/up bounce of the
bond.
For example, in bond tlb or alb mode, domu send some ARP request which go out
from dom0 bond's active slave, then the ARP broadcast request packets go back to
inactive slave from switch, because the inactive slave's inactive flag is zero,
kernel will receive the packets and pass them to bridge that cause dom0's bridge
map domu's MAC address to port of bond, bridge should map domu's MAC to port of
vif.
Signed-off-by: Zheng Li <zheng.x.li@oracle.com>
Signed-off-by: Jay Vosburgh <j.vosburgh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- The biggest change is core API extensions and mlx5 low-level driver
support for handling DIF/DIX-style protection information, and the
addition of PI support to the iSER initiator. Target support will be
arriving shortly through the SCSI target tree.
- A nice simplification to the "umem" memory pinning library now that
we have chained sg lists. Kudos to Yishai Hadas for realizing our
code didn't have to be so crazy.
- Another nice simplification to the sg wrappers used by qib, ipath and
ehca to handle their mapping of memory to adapter.
- The usual batch of fixes to bugs found by static checkers etc. from
intrepid people like Dan Carpenter and Yann Droneaud.
- A large batch of cxgb4, ocrdma, qib driver updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Ww6H
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband updates from Roland Dreier:
"Main batch of InfiniBand/RDMA changes for 3.15:
- The biggest change is core API extensions and mlx5 low-level driver
support for handling DIF/DIX-style protection information, and the
addition of PI support to the iSER initiator. Target support will
be arriving shortly through the SCSI target tree.
- A nice simplification to the "umem" memory pinning library now that
we have chained sg lists. Kudos to Yishai Hadas for realizing our
code didn't have to be so crazy.
- Another nice simplification to the sg wrappers used by qib, ipath
and ehca to handle their mapping of memory to adapter.
- The usual batch of fixes to bugs found by static checkers etc.
from intrepid people like Dan Carpenter and Yann Droneaud.
- A large batch of cxgb4, ocrdma, qib driver updates"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (102 commits)
RDMA/ocrdma: Unregister inet notifier when unloading ocrdma
RDMA/ocrdma: Fix warnings about pointer <-> integer casts
RDMA/ocrdma: Code clean-up
RDMA/ocrdma: Display FW version
RDMA/ocrdma: Query controller information
RDMA/ocrdma: Support non-embedded mailbox commands
RDMA/ocrdma: Handle CQ overrun error
RDMA/ocrdma: Display proper value for max_mw
RDMA/ocrdma: Use non-zero tag in SRQ posting
RDMA/ocrdma: Memory leak fix in ocrdma_dereg_mr()
RDMA/ocrdma: Increment abi version count
RDMA/ocrdma: Update version string
be2net: Add abi version between be2net and ocrdma
RDMA/ocrdma: ABI versioning between ocrdma and be2net
RDMA/ocrdma: Allow DPP QP creation
RDMA/ocrdma: Read ASIC_ID register to select asic_gen
RDMA/ocrdma: SQ and RQ doorbell offset clean up
RDMA/ocrdma: EQ full catastrophe avoidance
RDMA/cxgb4: Disable DSGL use by default
RDMA/cxgb4: rx_data() needs to hold the ep mutex
...
This patch adds support for the Micrel KSZ8864RMN switch to the spi_ks8995
driver. The KSZ8864RMN switch has a wider 256-byte register space.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
sxgbe_drv_probe: mdio and priv->hw leaks
sxgbe_drv_remove: clk and priv->hw leaks
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Acked-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Acked-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
An old inefficiency of the TX path that we are grant mapping the first slot,
and then copy the header part to the linear area. Instead, doing a grant copy
for that header straight on is more reasonable. Especially because there are
ongoing efforts to make Xen avoiding TLB flush after unmap when the page were
not touched in Dom0. In the original way the memcpy ruined that.
The key changes:
- the vif has a tx_copy_ops array again
- xenvif_tx_build_gops sets up the grant copy operations
- we don't have to figure out whether the header and first frag are on the same
grant mapped page or not
Note, we only grant copy PKT_PROT_LEN bytes from the first slot, the rest (if
any) will be on the first frag, which is grant mapped. If the first slot is
smaller than PKT_PROT_LEN, then we grant copy that, and later __pskb_pull_tail
will pull more from the frags (if any)
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename identifiers to state explicitly that they refer to map ops.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qlcnic driver fails to build on ARM with errors like:
In file included from drivers/net/ethernet/qlogic/qlcnic/qlcnic.h:36:0,
from drivers/net/ethernet/qlogic/qlcnic/qlcnic_hw.c:8:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.h:585:1: error: unknown type name 'irqreturn_t'
irqreturn_t qlcnic_83xx_clear_legacy_intr(struct qlcnic_adapter *);
^
Nothing in the driver is explicitly including the irq definitions, so we
add an include of linux/irq.h to pick them up.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The enic driver fails to build on ARM with:
In file included from drivers/net/ethernet/cisco/enic/enic_res.c:40:0:
drivers/net/ethernet/cisco/enic/enic.h:48:2: error: expected specifier-qualifier-list before 'irqreturn_t'
irqreturn_t (*isr)(int, void *);
^
Nothing in the driver is explicitly including the irq definitions, so we add
an include of linux/irq.h to pick them up.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2x driver fails to build on ARM with:
In file included from drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c:28:0:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h:243:1: error: unknown type name 'irqreturn_t'
irqreturn_t bnx2x_msix_sp_int(int irq, void *dev_instance);
^
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h:251:1: error: unknown type name 'irqreturn_t'
irqreturn_t bnx2x_interrupt(int irq, void *dev_instance);
^
Nothing in bnx2x_link.c or bnx2x_cmn.h is explicitly including the irq
definitions, so we add an include of linux/irq.h to pick them up.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds abi versioning between be2net and ocrdma driver modules
to catch functional incompatibilities in the two drivers.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
fix build errors:
drivers/net/ethernet/ti/cpts.c:266:12: error: 'ETH_HLEN' undeclared (first use in this function)
drivers/net/ethernet/ti/cpts.c:276:23: error: 'VLAN_HLEN' undeclared (first use in this function)
Fixes: 408eccce32 ("net: ptp: move PTP classifier in its own file")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Suggested-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Here is my initial pull request for the networking subsystem during
this merge window:
1) Support for ESN in AH (RFC 4302) from Fan Du.
2) Add full kernel doc for ethtool command structures, from Ben
Hutchings.
3) Add BCM7xxx PHY driver, from Florian Fainelli.
4) Export computed TCP rate information in netlink socket dumps, from
Eric Dumazet.
5) Allow IPSEC SA to be dumped partially using a filter, from Nicolas
Dichtel.
6) Convert many drivers to pci_enable_msix_range(), from Alexander
Gordeev.
7) Record SKB timestamps more efficiently, from Eric Dumazet.
8) Switch to microsecond resolution for TCP round trip times, also
from Eric Dumazet.
9) Clean up and fix 6lowpan fragmentation handling by making use of
the existing inet_frag api for it's implementation.
10) Add TX grant mapping to xen-netback driver, from Zoltan Kiss.
11) Auto size SKB lengths when composing netlink messages based upon
past message sizes used, from Eric Dumazet.
12) qdisc dumps can take a long time, add a cond_resched(), From Eric
Dumazet.
13) Sanitize netpoll core and drivers wrt. SKB handling semantics.
Get rid of never-used-in-tree netpoll RX handling. From Eric W
Biederman.
14) Support inter-address-family and namespace changing in VTI tunnel
driver(s). From Steffen Klassert.
15) Add Altera TSE driver, from Vince Bridgers.
16) Optimizing csum_replace2() so that it doesn't adjust the checksum
by checksumming the entire header, from Eric Dumazet.
17) Expand BPF internal implementation for faster interpreting, more
direct translations into JIT'd code, and much cleaner uses of BPF
filtering in non-socket ocntexts. From Daniel Borkmann and Alexei
Starovoitov"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1976 commits)
netpoll: Use skb_irq_freeable to make zap_completion_queue safe.
net: Add a test to see if a skb is freeable in irq context
qlcnic: Fix build failure due to undefined reference to `vxlan_get_rx_port'
net: ptp: move PTP classifier in its own file
net: sxgbe: make "core_ops" static
net: sxgbe: fix logical vs bitwise operation
net: sxgbe: sxgbe_mdio_register() frees the bus
Call efx_set_channels() before efx->type->dimension_resources()
xen-netback: disable rogue vif in kthread context
net/mlx4: Set proper build dependancy with vxlan
be2net: fix build dependency on VxLAN
mac802154: make csma/cca parameters per-wpan
mac802154: allow only one WPAN to be up at any given time
net: filter: minor: fix kdoc in __sk_run_filter
netlink: don't compare the nul-termination in nla_strcmp
can: c_can: Avoid led toggling for every packet.
can: c_can: Simplify TX interrupt cleanup
can: c_can: Store dlc private
can: c_can: Reduce register access
can: c_can: Make the code readable
...
doubling of the default queue length though.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJTOirvAAoJENkgDmzRrbjxpqAP/3114WOubf4MNoi24eXNkU2x
ZC++orq408A72g8dB7A0XAhatKc8Ay0bDP5hOZNAgTHm2hjYxmhpC9UlKEzzElpW
yjwR0wYBXA0RoJuZqCp9MNgOtkU54QoQZ0c4EZblagslUZBmKQPUDE7XdgkaqO6o
A3azfCjAFDu523Azep9Npj1sk+H+VH3OIXyMGY+uyHBw1a2rnmIhn4lQCQ+pX+YO
3wpqxEragpjBAizs1CAAB9wWm2O8zVACxkoUXVYI8Tu60n99lwr9Abxlc0oHSIig
E7kBnyzQVHfkDrPXR3EdwTi3Hwd/BaOiW4dPvQ3IJKvPOzoiS4H3IpJCnCV5PfRb
VHl3q//SzPQ+GXH7WH2Fhb9JxoLxBRzFcy3kdIR1wBHYahAOiQjcLgapOO5mVq3X
PJy9CDs2L9rjbtxvQWtnl62V3JFGw+ZdhhG/BjeC5Who/aSh/mDoss7/qdfrxKJx
z5IWYSlJw7ighOuF0dPdCKAX9WiWqENvga31Q2svrH4Hxlx6eGumEmX+YQw0iRAf
ddMYA+1qLT4myPTN0nORFM+T/mkZHNkNMCr0qylRFH0j6hSiDxwWqQG0eXA661By
W6nIkW++sj2Vkk4knMGCXSyMmy9Nrv+1R+8unQJCXixYevotP5JEY0DoCQwlGuuq
xa0UR+2q9Htnbytu8S0K
=AoMS
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"Nothing exciting: virtio-blk users might see a bit of a boost from the
doubling of the default queue length though"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio-blk: base queue-depth on virtqueue ringsize or module param
Revert a02bbb1ccfe8: MAINTAINERS: add virtio-dev ML for virtio
virtio: fail adding buffer on broken queues.
virtio-rng: don't crash if virtqueue is broken.
virtio_balloon: don't crash if virtqueue is broken.
virtio_blk: don't crash, report error if virtqueue is broken.
virtio_net: don't crash if virtqueue is broken.
virtio_balloon: don't softlockup on huge balloon changes.
virtio: Use pci_enable_msix_exact() instead of pci_enable_msix()
MAINTAINERS: virtio-dev is subscribers only
tools/virtio: add a missing )
tools/virtio: fix missing kmemleak_ignore symbol
tools/virtio: update internal copies of headers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlM6jfsACgkQjTAFq1RaXHOVTwCeOyOYOJ+Ze2x33WydGcGsvX8a
QPoAoJVAcekmL5MVbcMTTvc8QL1AebAm
=4aEp
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-3.15-20140401' of git://gitorious.org/linux-can/linux-can
linux-can-fixes-for-3.15-20140401
Marc Kleine-Budde says:
====================
this is a pull request of 16 patches for the 3.15 release cycle.
Bjorn Van Tilt contributes a patch which fixes a memory leak in usb_8dev's
usb_8dev_start_xmit()s error path. A patch by Robert Schwebel fixes a typo in
the can documentation. The remaining patches all target the c_can driver. Two
of them are by me; they add a missing netif_napi_del() and return value
checking. Thomas Gleixner contributes 12 patches, which address several
shortcomings in the driver like hardware initialisation, concurrency, message
ordering and poor performance.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2b3d7b758c687("qlcnic: Add VXLAN Rx offload support") uses
vxlan_get_rx_port() which caused build failure when VXLAN=m.
This patch fixes the build failure by adding dependency on VXLAN
in Kconfig of qlcnic module and use vxlan_get_rx_port() and support
code accordingly.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes a build error reported by Fengguang, that is
triggered when CONFIG_NETWORK_PHY_TIMESTAMPING is not set:
ERROR: "ptp_classify_raw" [drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe.ko] undefined!
The fix is to introduce its own file for the PTP BPF classifier,
so that PTP_1588_CLOCK and/or NETWORK_PHY_TIMESTAMPING can select
it independently from each other. IXP4xx driver on ARM needs to
select it as well since it does not seem to select PTP_1588_CLOCK
or similar that would pull it in automatically.
This also allows for hiding all of the internals of the BPF PTP
program inside that file, and only exporting relevant API bits
to drivers.
This patch also adds a kdoc documentation of ptp_classify_raw()
API to make it clear that it can return PTP_CLASS_* defines. Also,
the BPF program has been translated into bpf_asm code, so that it
can be more easily read and altered (extensively documented in [1]).
In the kernel tree under tools/net/ we have bpf_asm and bpf_dbg
tools, so the commented program can simply be translated via
`./bpf_asm -c prog` where prog is a file that contains the
commented code. This makes it easily readable/verifiable and when
there's a need to change something, jump offsets etc do not need
to be replaced manually which can be very error prone. Instead,
a newly translated version via bpf_asm can simply replace the old
code. I have checked opcode diffs before/after and it's the very
same filter.
[1] Documentation/networking/filter.txt
Fixes: 164d8c6665 ("net: ptp: do not reimplement PTP/BPF classifier")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jiri Benc <jbenc@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "core_ops" variable isn't referenced outside this file and Sparse
complains about it:
drivers/net/ethernet/samsung/sxgbe/sxgbe_core.c:239:29: warning:
symbol 'core_ops' was not declared. Should it be static?
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bitwise '|' was intended here instead of logical '||'.
Fixes: 1edb9ca69e ('net: sxgbe: add basic framework for Samsung 10Gb ethernet driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"err" is always zero at this point so we always unregister and free the
mdio_bus before returning success. This seems like left over code and
I have deleted it.
Fixes: 1edb9ca69e ('net: sxgbe: add basic framework for Samsung 10Gb ethernet driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the "separate_tx_channels=1" module parameter, the TX queues are
initially numbered starting from the first TX-only channel number (after all the
RX-only channels). efx_set_channels() renumbers the queues so that they are
indexed from zero.
On EF10, the TX queues need to be relabelled in this way before calling the
dimension_resources NIC type operation, otherwise the TX queue PIO buffers can be
linked to the wrong VIs when using "separate_tx_channels=1".
Added comments to explain UC/WC mappings for PIO buffers
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When netback discovers frontend is sending malformed packet it will
disables the interface which serves that frontend.
However disabling a network interface involving taking a mutex which
cannot be done in softirq context, so we need to defer this process to
kthread context.
This patch does the following:
1. introduce a flag to indicate the interface is disabled.
2. check that flag in TX path, don't do any work if it's true.
3. check that flag in RX path, turn off that interface if it's true.
The reason to disable it in RX path is because RX uses kthread. After
this change the behavior of netback is still consistent -- it won't do
any TX work for a rogue frontend, and the interface will be eventually
turned off.
Also change a "continue" to "break" after xenvif_fatal_tx_err, as it
doesn't make sense to continue processing packets if frontend is rogue.
This is a fix for XSA-90.
Reported-by: Török Edwin <edwin@etorok.net>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that vxlan_get_rx_port() is present in the kernel build in a manner
consistent with mlx4, else mlx4 can be made built-in where vxlan a module and
the phase of the build linking fails. Add CONFIG_MLX4_EN_VXLAN for that.
Also, #ifdef the advertizement and implementation of the mlx4 vxlan ndo
calls and related code under this config directive.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a CONFIG_BE2NET_VXLAN define to control be2net's build
dependency on the VXLAN driver.
Without this fix, the kernel build fails when VxLAN driver is
selected to be built as a module while be2net is built-in.
fixes: c9c47142 ("be2net: csum, tso and rss steering offload support for VxLAN")
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point to toggle the RX led for every packet. Especially if
we have a full FIFO we want to avoid everything we can.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The function loads the message object from the hardware to get the
payload length. The previous patch stores that information in an
array, so we can avoid the hardware access.
Remove the hardware access and move the led toggle outside of the
spinlocked region. Toggle the led only once when at least one packet
has been received.
Binary size shrinks along with the code
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We can avoid the HW access in TX cleanup path for retrieving the DLC
of the sent package if we store the DLC in a private array.
Ideally this should be handled in the can_echo_skb functions, but I
leave that exercise to the CAN folks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
commit 4ce78a838c (can: c_can: Speed up rx_poll function) hyped a
performance improvement by reducing the access to the interrupt
pending register from a dual 16 bit to a single 16 bit access. Wow!
Thereby it crippled the driver to cast the 16 msg objects in stone,
which is completly braindead as contemporary hardware has up to 128
message objects. Supporting larger object buffers is a major surgery,
but it'd be definitely worth it especially as the driver does not
support HW message filtering ....
The logic of the "FIFO" implementation is to split the FIFO in half.
For the lower half we read the buffers and clear the interrupt pending
bit, but keep the newdat bit set, so the HW will queue above those
buffers.
When we read out the last low buffer then we reenable all the low half
buffers by clearing the newdat bit.
The upper half buffers clear the newdat and the interrupt pending bit
right away as we know that the lower half bits are clear and give us a
headstart against the hardware.
Now the implementation is:
transfer_message_object()
read_object_and_put_into_skb();
if (obj < END_OF_LOW_BUF)
clear_intpending(obj)
else if (obj > END_OF_LOW_BUF)
clear_intpending_and_newdat(obj)
else if (obj == END_OF_LOW_BUF)
clear_newdat_of_all_low_objects()
The hardware allows to avoid most of the mess simply because we can
tell the transfer_message_object() function to clear bits right away.
So we can be clever and do:
if (obj <= END_OF_LOW_BUF)
ctrl = TRANSFER_MSG | CLEAR_INTPND;
else
ctrl = TRANSFER_MSG | CLEAR_INTPND | CLEAR_NEWDAT;
transfer_message_object(ctrl)
read_object_and_put_into_skb();
if (obj == END_OF_LOW_BUF)
clear_newdat_of_all_low_objects()
So we save a complete control operation on all message objects except
the one which is the end of the low buffer. That's a few micro seconds
per object.
I'm not adding a boasting profile to that, simply because it's self
explaining.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[mkl: adjusted subject and commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If every other line contains line breaks, that's a clear sign for
indentation level madness. Split out the inner loop and move the code
to a separate function. gcc creates slightly worse code for that, but
we'll fix that in the next step.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[mkl: adjusted subject]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The network core does not serialize the access to the hardware. The
xmit related code lets the following happen:
CPU0 CPU1
interrupt()
do_poll()
c_can_do_tx()
Fiddle with HW and xmit()
internal data Fiddle with HW and
internal data
due the complete lack of serialization.
Add proper locking.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The rx_poll code has the following gem:
if (msg_ctrl_save & IF_MCONT_EOB)
return num_rx_pkts;
The EOB bit is the indicator for the hardware that this is the last
configured FIFO object. But this object can contain valid data, if we
manage to free up objects before the overrun case hits.
Now if the code exits due to the EOB bit set, then this buffer is
stale and the interrupt bit and NewDat bit of the buffer are still
set. Results in a nice interrupt storm unless we come into an overrun
situation where the MSGLST bit gets set.
ksoftirqd/0-3 [000] ..s. 79.124101: c_can_poll: rx_poll: val: 00008001 pend 00008001
ksoftirqd/0-3 [000] ..s. 79.124176: c_can_poll: rx_poll: val: 00008000 pend 00008000
ksoftirqd/0-3 [000] ..s. 79.124187: c_can_poll: rx_poll: val: 00008002 pend 00008002
ksoftirqd/0-3 [000] ..s. 79.124256: c_can_poll: rx_poll: val: 00008000 pend 00008000
ksoftirqd/0-3 [000] ..s. 79.124267: c_can_poll: rx_poll: val: 00008000 pend 00008000
The amazing thing is that the check of the MSGLST (aka overrun bit)
used to be after the check of the EOB bit. That was "fixed" in commit
5d0f801a2c(can: c_can: Fix RX message handling, handle lost message
before EOB). But the author of this "fix" did not even understand that
the EOB check is broken as well.
Again a simple solution: Remove
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[mkl: adjusted subject and commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The lost message handling is broken in several ways.
1) Clearing the message lost flag is done by writing 0 to the
message control register of the object.
#define IF_MCONT_CLR_MSGLST (0 << 14)
That clears the object buffer configuration in the worst case,
which results in a loss of the EOB flag. That leaves the FIFO chain
without a limit and causes a complete lockup of the HW
2) In case that the error skb allocation fails, the code happily
claims that it handed down a packet. Just an accounting bug, but ....
3) The code adds a lot of pointless overhead to that error case, where
we need to get stuff done as fast as possible to avoid more packet
loss.
- printk an annoying error message
- reread the object buffer for nothing
Fix is simple again:
- Use the already known MSGCTRL content and only clear the MSGLST bit
- Fix the buffer accounting by adding a proper return code
- Remove the pointless operations
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The buffer handling of c_can has been broken forever. That leads to
message reordering:
ksoftirqd/0-3 [000] ..s. 79.123776: c_can_poll: rx_poll: val: 00007fff
ksoftirqd/0-3 [000] ..s. 79.124101: c_can_poll: rx_poll: val: 00008001
What happens is:
CPU HW
queue new packet into obj 16 (0-15 are busy)
read obj 1-15
return because pending is 0
set pending obj 16 -> pending reg 8000
queue new packet into obj 1
set pending obj 1 -> pending reg 8001
So the current algorithmus reads the newest message first, which
violates the ordering rules of CAN.
Add proper handling of that situation by analyzing the contents of the
pending register for gaps.
This does NOT fix the message object corruption which can lead to
interrupt storms. Thats addressed in the next patches.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[mkl: adjusted subject]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The hardware has two message control interfaces, but the code only uses the
first one. So on SMP the following can be observed:
CPU0 CPU1
rx_poll()
write IF1 xmit()
write IF1
write IF1
That results in corrupted message object configurations. The TX/RX is not
globally serialized it's only serialized on a core.
Simple solution: Let RX use IF1 and TX use IF2 and all is good.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The function is broken in several ways:
- The function does not wait for the init to complete.
That can take quite some microseconds.
- No protection against being called for two chips at the same
time. SMP is such a new thing, right?
Clear the start and the init done bit unconditionally and wait for both bits to
be clear.
In the enable path set the init bit and wait for the init done bit.
Add proper locking.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
According to the documentation the CPU must wait for CONTROL_INIT to
be cleared before writing to the baudrate registers.
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fixed a memory leak when an error occurred in the transmit function. In the
error handling the urb wasn't freed before returning. There was also a call to
the usb_unanchor_urb() function but the urb wasn't anchored.
Signed-off-by: Bjorn Van Tilt <bjorn.vantilt@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Resolve some rcu warnings produced when LER actions take place.
This appears to be due to not holding the rtnl lock when calling
ixgbe_down, so hold the lock. Also avoid disabling the device
when it is already disabled. This check is necessary because the
callback can be called more than once in some cases.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Resolve some rcu warnings produced when LER actions take place.
This appears to be due to not holding the rtnl lock when calling
ixgbe_down, so hold the lock. Also avoid disabling the device
when it is already disabled. This check is necessary because the
callback can be called more than once in some cases.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use pci_iounmap instead of iounmap when the virtual mapping was done
with pci_iomap. A simplified version of the semantic patch that finds this
issue is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression addr;
@@
addr = pci_iomap(...)
@rr@
expression r.addr;
@@
* iounmap(addr)
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Casting a pointer to a pointer of the same type is pointless,
so remove these unnecessary casts.
Done via coccinelle script:
$ cat typecast_2.cocci
@@
type T;
T *foo;
@@
- (T *)foo
+ foo
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Using addressof then casting to the original type is pointless,
so remove these unnecessary casts.
Done via coccinelle script:
$ cat typecast.cocci
@@
type T;
T foo;
@@
- (T *)&foo
+ &foo
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The commit 6494294f27 ("i40e/i40evf: Use
dma_set_mask_and_coherent") uses dma_set_mask_and_coherent() to
replace dma_set_coherent_mask() for the benefit of return error.
The conversion brings some confusion in error checking as whether
against DMA_BIT_MASK(64) or DMA_BIT_MASK(32). For one, if error is
zero, the check will be against DMA_BIT_MASK(64) twice. Fix this
error checking by binding the check to the pertinent one.
Cc: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The commit c7d05ca89f ("i40e: driver ethtool core") introduced the
new function i40e_add_del_fdir_sctpv4() with the kernel doc
description a little bit off. The trivial error was copied over to a
different file by the commit 17a73f6b14 ("i40e: Flow Director
sideband accounting") most recently. Fix the kernel doc with the
correct description for clarity.
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change the ixgbe_read_reg function name to ixgbevf_read_reg to
avoid a namespace clash with the ixgbe driver. This will allow
ixgbe to take its register read function out-of-line to reduce
memory footprint.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The commit c97506ab0e ("ixgbe: Add check for FW veto bit")
introduced the new function ixgbe_check_reset_blocked() with a minor
issue in declaration. Fix the declaration by changing the type
specifier to bool as the definition returns a boolean value.
Additionally all ixgbe_check_reset_blocked() callers are expected to
return a boolean value.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe has a single set of TX time stamping resources per NIC.
Use a simple bit lock to avoid race conditions and leaking skbs
when multiple TX rings try to claim time stamping.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
skb_tx_timestamp() does not report software time stamp
if SKBTX_IN_PROGRESS is set. According to timestamping.txt
software time stamps are a fallback and should not be
generated if hardware time stamp is provided.
Move call to skb_tx_timestamp() after setting
SKBTX_IN_PROGRESS.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ptp_tx_skb is always set before work is scheduled,
work is cancelled before ptp_tx_skb is set to NULL.
PTP work cannot ever see ptp_tx_skb set to NULL.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit da1e2046e5, the flow for enabling/disabling an Si errata
workaround (e1000_lv_jumbo_workaround_ich8lan) was changed to fix a problem
with iAMT connections dropping on interface down with jumbo frames set.
Part of this change was to move the function call disabling the workaround
to e1000e_down() from the e1000_setup_rctl() function. The mechanic for
disabling of this workaround involves writing several MAC and PHY registers
back to hardware defaults.
After this commit, when the driver is loaded with the cable out, the PHY
registers are not programmed with the correct default values. This causes
the device to be capable of transmitting packets, but is unable to recieve
them until this workaround is called.
The flow of e1000e's open code relies upon calling the above workaround to
expicitly program these registers either with jumbo frame appropriate settings
or h/w defaults on 82579 and newer hardware.
Fix this issue by adding logic to e1000_setup_rctl() that not only calls
e1000_lv_jumbo_workaround_ich8lan() when jumbo frames are set, to enable the
workaround, but also calls this function to explicitly disable the workaround
in the case that jumbo frames are not set.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull workqueue changes from Tejun Heo:
"PREPARE_[DELAYED_]WORK() were used to change the work function of work
items without fully reinitializing it; however, this makes workqueue
consider the work item as a different one from before and allows the
work item to start executing before the previous instance is finished
which can lead to extremely subtle issues which are painful to debug.
The interface has never been popular. This pull request contains
patches to remove existing usages and kill the interface. As one of
the changes was routed during the last devel cycle and another
depended on a pending change in nvme, for-3.15 contains a couple merge
commits.
In addition, interfaces which were deprecated quite a while ago -
__cancel_delayed_work() and WQ_NON_REENTRANT - are removed too"
* 'for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: remove deprecated WQ_NON_REENTRANT
workqueue: Spelling s/instensive/intensive/
workqueue: remove PREPARE_[DELAYED_]WORK()
staging/fwserial: don't use PREPARE_WORK
afs: don't use PREPARE_WORK
nvme: don't use PREPARE_WORK
usb: don't use PREPARE_DELAYED_WORK
floppy: don't use PREPARE_[DELAYED_]WORK
ps3-vuart: don't use PREPARE_WORK
wireless/rt2x00: don't use PREPARE_WORK in rt2800usb.c
workqueue: Remove deprecated __cancel_delayed_work()
Conflicts:
drivers/net/xen-netback/netback.c
A bug fix overlapped with changing how the netback SKB control
block is implemented.
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless-next 2014-03-31
Please accept this one last round of general wireless updates for
the 3.15 merge window!
For the Bluetooth bits, Gustavo says:
"Here follow another set of patches to 3.15. This is mostly a bug fix
pull request with the exception of one commit from Marcel which adds
tracking to the current configured LE scan type parameter."
Beyond that, notable bits include some final refactoring of rtl8180
and the addition of the rtl8187se driver, fixes for a number of
problems identified by Dan Carpenter and his static analysis tools,
and a handful of other bits here and there.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While transmit over a at86rf231 device and unloading the module I got:
[ 29.643073] WARNING: CPU: 0 PID: 3 at kernel/workqueue.c:1335 __queue_work+0xb4/0x224()
[ 29.651457] Modules linked in: at86rf230(-) autofs4
[ 29.656612] CPU: 0 PID: 3 Comm: ksoftirqd/0 Tainted: G W 3.14.0-rc6-01602-g902659e-dirty #294
[ 29.666490] [<c00124f0>] (unwind_backtrace) from [<c0010ad0>] (show_stack+0x10/0x14)
[ 29.674628] [<c0010ad0>] (show_stack) from [<c0032c80>] (warn_slowpath_common+0x60/0x80)
[ 29.683116] [<c0032c80>] (warn_slowpath_common) from [<c0032d30>] (warn_slowpath_null+0x18/0x20)
[ 29.692329] [<c0032d30>] (warn_slowpath_null) from [<c0045b08>] (__queue_work+0xb4/0x224)
[ 29.700906] [<c0045b08>] (__queue_work) from [<c0045cc8>] (queue_work_on+0x50/0x78)
[ 29.708944] [<c0045cc8>] (queue_work_on) from [<c05669cc>] (mac802154_tx+0x1e4/0x240)
[ 29.717164] [<c05669cc>] (mac802154_tx) from [<c0471814>] (dev_hard_start_xmit+0x2f0/0x43c)
[ 29.725926] [<c0471814>] (dev_hard_start_xmit) from [<c04878d0>] (sch_direct_xmit+0x64/0x2a0)
[ 29.734867] [<c04878d0>] (sch_direct_xmit) from [<c0487c38>] (__qdisc_run+0x12c/0x18c)
[ 29.743169] [<c0487c38>] (__qdisc_run) from [<c046e1b0>] (net_tx_action+0xe0/0x178)
[ 29.751205] [<c046e1b0>] (net_tx_action) from [<c0036690>] (__do_softirq+0x100/0x264)
[ 29.759420] [<c0036690>] (__do_softirq) from [<c0036818>] (run_ksoftirqd+0x24/0x4c)
[ 29.767453] [<c0036818>] (run_ksoftirqd) from [<c005232c>] (smpboot_thread_fn+0x128/0x13c)
[ 29.776121] [<c005232c>] (smpboot_thread_fn) from [<c004c3fc>] (kthread+0xd0/0xe4)
[ 29.784061] [<c004c3fc>] (kthread) from [<c000da88>] (ret_from_fork+0x14/0x2c)
[ 29.791628] ---[ end trace 3406ff24bd973834 ]---
The problem is there are still interrupts after deregister ieee802154
device. This patch mask all interrupts in the at86rf2xx chips before
deregister the device.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Though we made sure to acquire a valid MAC for
the netdevice we never actually programmed it
into the hardware.
So if the bootloader did not set the MAC,
network operation would only work if userspace
explicitly asked to transfer the MAC to hardware.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device provides QMI and ethernet functionality via a standard CDC
ethernet descriptor. But when driven by cdc_ether, the QMI
functionality is unavailable because only cdc_ether can claim the USB
interface. Thus blacklist the device in cdc_ether and add its IDs to
qmi_wwan, which enables both QMI and ethernet simultaneously.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If allocation of io_dmabuf fails, rtl8187_probe() calls usb_put_dev(udev)
while usb_get_dev(udev) is not called yet. As a result refcnt is decremented
incorrectly and usb_dev can be used after memory deallocation.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In rtl8180/rtl8185/rtl8187se the register space is represented
using packed structure type. Register are thus accessed using a
pointer of this type.
All registers are packed toghether, and only small gaps are present.
However Rtl8187se has also some "sparse" registers, very far from
the "main register block".
It could be possible to access them by simply declare huge reserved
blocks inside the register struct (and this causes NO memory waste).
However, for various reasons, access to those "far" registers is
done with special dedicated macros, without declaring them in the
register struct.
This is done in an intricate manner, that makes code less readable
and caused static analisys tool to produce warnings.
This patch keeps the "macro" mechanism, but it changes its
implementation in a simplier and more straightforward way.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a missing set of curly braces here so the debug output says
"Probe confirm received" unintentionally.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ANAPARAM3 register, defined in the rtl818x common register
struct, is accessed as 16bit by rtl8187se and as 8bit by rtl8187b.
Since I have no documentation about this, I can only stick to
the reference code and to what is known to work.
This issue has been addressed by a patch from Larry Finger
that introduces an "union", in the register struct.
In my last patch-set I applied it on the register struct, but
I forget to update rtl8187 driver too.
This patch does it.
Suggested-by: Larry Finger <Larry.Finger@lwfinger.net> [ Original patch ]
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some HP notebooks using this rtl8188ee hardware module can't get
AP scan results with pin-based interrupts mode, enabling MSI interrupts
mode could fix it.
As RealTek's testing results, RTL8188EE works well with both MSI mode
and pin-based mode fallback.
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add MSI interrupts mode support, enable it when submodules' msi_support
flag is true, also could fallback to pin-based interrupts mode if MSI
interrupts mode fails.
RealTek's policy(on modules which work well with MSI interrupts mode) is:
> If the platform supports both MSI and pin-based, use MSI.
> If the platform supports MSI only, use MSI.
> If the platform supports pin-based only, use pin-based.
Also as RealTek's testing results, RTL8188EE and RTL8723BE work well
with both MSI mode and pin-based mode fallback.
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It has been observed that system hangs during suspend, if host
sleep activation fails due to a missing interrupt from firmware.
Use timeout variant, so that the thread will be woken up when
timer expires.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a thread is interrupted by signal, all
wait_event_interruptible calls after queueing commands return
an error. Numbers of commands in pending queue are increased
in this case. Sometimes all commands nodes in pool are filled.
We will cancel pending commands when signal is received.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When scan request is received, scan commands are prepared and
queued into scan pending queue. There is a corner case when
command nodes are full. So we stop queueing further scan
commands and return an error. This patch makes sure that
currently queued commands in scan pending queue are also freed
in this case.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For the ppp driver, there are currently two open-coded BPF filters in use,
that is, pass_filter and active_filter. Migrate both to make proper use
of sk_unattached_filter_{create,destroy} API so that the actual BPF code
is decoupled from direct access, and filters can be jited as a side-effect
by the internal filter compiler.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linux-ppp@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
There are currently pch_gbe, cpts, and ixp4xx_eth drivers that open-code
and reimplement a BPF classifier for the PTP protocol. Since all of them
effectively do the very same thing and load the very same PTP/BPF filter,
we can just consolidate that code by introducing ptp_classify_raw() in
the time-stamping core framework which can be used in drivers.
As drivers get initialized after bootstrapping the core networking
subsystem, they can make use of ptp_insns wrapped through
ptp_classify_raw(), which allows to simplify and remove PTP classifier
setup code in drivers.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BUG_ON to catch ring overflow in xenvif_rx_action() makes the assumption
that meta_slots_used == ring slots used. This is not necessarily the case
for GSO packets, because the non-prefix GSO protocol consumes one more ring
slot than meta-slot for the 'extra_info'. This patch changes the test to
actually check ring slots.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
The worse-case estimate for skb ring slot usage in xenvif_rx_action()
fails to take fragment page_offset into account. The page_offset does,
however, affect the number of times the fragmentation code calls
start_new_rx_buffer() (i.e. consume another slot) and the worse-case
should assume that will always return true. This patch adds the page_offset
into the DIV_ROUND_UP for each frag.
Unfortunately some frontends aggressively limit the number of requests
they post into the shared ring so to avoid an estimate that is 'too'
pessimal it is capped at MAX_SKB_FRAGS.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a test in start_new_rx_buffer() that checks whether
a copy operation is less than MAX_BUFFER_OFFSET in length, since
MAX_BUFFER_OFFSET is defined to be PAGE_SIZE and the only caller of
start_new_rx_buffer() already limits copy operations to PAGE_SIZE or less.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Reported-By: Sander Eikelenboom <linux@eikelenboom.it>
Tested-By: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/marvell/mvneta.c
The mvneta.c conflict is a case of overlapping changes,
a conversion to devm_ioremap_resource() vs. a conversion
to netdev_alloc_pcpu_stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
The at8031 can work on polling mode and interrupt mode.
Add ack_interrupt and config intr funcs to enable
interrupt mode for it.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gfp parameter was added in:
commit 47be03a28c
Author: Amerigo Wang <amwang@redhat.com>
Date: Fri Aug 10 01:24:37 2012 +0000
netpoll: use GFP_ATOMIC in slave_enable_netpoll() and __netpoll_setup()
slave_enable_netpoll() and __netpoll_setup() may be called
with read_lock() held, so should use GFP_ATOMIC to allocate
memory. Eric suggested to pass gfp flags to __netpoll_setup().
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reason for the gfp parameter was removed in:
commit c4cdef9b71
Author: dingtianhong <dingtianhong@huawei.com>
Date: Tue Jul 23 15:25:27 2013 +0800
bonding: don't call slave_xxx_netpoll under spinlocks
The slave_xxx_netpoll will call synchronize_rcu_bh(),
so the function may schedule and sleep, it should't be
called under spinlocks.
bond_netpoll_setup() and bond_netpoll_cleanup() are always
protected by rtnl lock, it is no need to take the read lock,
as the slave list couldn't be changed outside rtnl lock.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing else that calls __netpoll_setup or ndo_netpoll_setup
requires a gfp paramter, so remove the gfp parameter from both
of these functions making the code clearer.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Nithin Nayak Sujir <nsujir@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Chris Snook <chris.snook@gmail.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Chris Snook <chris.snook@gmail.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta driver currently uses of_iomap(), which has two drawbacks:
it doesn't request the resource, and it isn't devm-style so some error
handling is needed.
This commit switches to use devm_ioremap_resource() instead, which
automatically requests the resource (so the I/O registers region shows
up properly in /proc/iomem), and also is devm-style, which allows to
get rid of some error handling to unmap the I/O registers region.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For completeness, turn off vlan rx acceleration in vlan_features so
that it doesn't show up on q-in-q setups.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not include vlan acceleration features in vlan_features as that
precludes correct Q-in-Q operation.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qlge driver turns off NETIF_F_HW_CTAG_FILTER, but forgets to
turn off HW_CTAG_TX and HW_CTAG_RX on vlan devices. With the
current settings, q-in-q will only generate a single vlan header.
Remember to mask off CTAG_TX and CTAG_RX features in vlan_features.
CC: Shahed Shaikh <shahed.shaikh@qlogic.com>
CC: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
CC: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As in xmit path we merely update statistics and free the skb, we
can mark the device with LLTX feature, so that upper layers can
avoid taking the single txq lock on xmit. While at it, also add
missing NETIF_F_SG.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add implementation for the add/del vxlan port ndo calls, using the
CONFIG_DEV firmware command.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the CONFIG_DEV firmware command which we will use to
configure the UDP port assumed by the firmware for the VXLAN offloads.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VF issues a firmware command which is disallowed for them, the PF
rerturns -EPERM from that command wrapper. Move to use one such wrapper
instance, instead of repeating the same code on such commands.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2dc33bbc4 "bnx2x: Remove the sriov VFOP mechanism" introduced a possible
memory leak on the error flow during multicast filters configuration.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pm_rumtime work queue is causing the device to be suspended during
initialisation, thus the initialisation may not be able to access registers
properly. As the code is called from a work queue, it is possible that this
is not seen from certain configurations/builds due to the asynchronos
nature of the code.
Another issue has also been found where the network device registration
calls back into the driver thus causing further pm_runtime calls that
also caused issues with the MDIO bus code. This has now been checked
and is the only place the MDIO can be called without the device open.
Use pm_runtime_get_sync() and pm_runtime_put() to ensure that the
pm system does not suspend it during the probe() call and remove the
now unnecessary pm_runtime_resume() call. Also add a call in the error
path to call pm_runtime_disable().
This fixes the external abort that can cause /sbin/init or other such
init processed to die.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like the STi and sunxi series SOCs, Altera's SOCFPGA also needs a glue layer
on top of the Synopsys gmac IP.
This patch adds the platform driver for the glue layer which configures the IP
before the generic STMMAC driver takes over.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to e1000e, igb, i40e and i40evf
Anjali provides i40e fix to remove the ATR filter on RST as well as FIN
packets. Cleans up add_del_fdir() because it was used and implemented
only for the add, so change the name and drop a parameter. Adds the
ability to drop a flow if we wanted to and adds a flow director
message level to be used for flow director specific messages.
Mitch fixes an issue on i40evf where the Tx watchdog handler was causing
an oops when sending an admin queue message to request a reset because
the admin queue functions use spinlocks.
Greg provides a change to i40e to make the alloc and free queue vector
calls orthogonal.
Shannon fixes i40e to verify the eeprom checksum and firmware CRC status
bits, and shutdown the driver if they fail. This change stops the
processing of traffic, but does not kill the PF netdev so that the
NVMUpdate process still has a chance at fixing the image. Also provides
a fix to make sure the VSI has a netdev before trying to use it in
the debugfs netdev_ops commands.
Jakub Kicinski provides patches for e1000e and igb to fix a number issues
found in the PTP code.
v2:
- drop patch 11 "i40e: Add a fallback debug flow for the driver" from the
series based on feedback from David Miller
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes following:
drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c:1828 sxgbe_hw_init()
error: potential null dereference 'priv->hw'. (kmalloc returns null)
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes followings:
sparse warnings: (new ones prefixed by >>)
>> drivers/net/ethernet/samsung/sxgbe/sxgbe_platform.c:197:5:
sparse: symbol 'sxgbe_platform_freeze' was not declared. Should it be static?
>> drivers/net/ethernet/samsung/sxgbe/sxgbe_platform.c:204:5:
sparse: symbol 'sxgbe_platform_restore' was not declared. Should it be static?
>> drivers/net/ethernet/samsung/sxgbe/sxgbe_platform.c:228:24:
sparse: symbol 'sxgbe_platform_driver' was not declared. Should it be static?
>> drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c:1795:6:
sparse: symbol 'sxgbe_get_ops' was not declared. Should it be static?
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch mainly implements the add/del_vxlan_port() methods by invoking
the needed FW cmds for supporting VxLAN offloads for Skyhawk-R.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the FW cmds needed for VxLAN offloads
on Skyhawk-R:
1) The VxLAN UDP port needs to be configured via the port-desc of
SET_PROFILE_CONFIG_v1 cmd.
This patch re-factors the be_set_profile_config() code (used so far
only for setting VF QoS) to be used to set any type of descriptor.
2) The MANAGE_IFACE_FILTERS cmds is needed to convert a normal interface
into a tunnel interface. This allows for RSS to work even on the inner
TCP/UDP headers of VxLAN traffic.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
igb has a single set of TX time stamping resources per NIC.
Use a simple bit lock to avoid race conditions and leaking skbs
when multiple TX rings try to claim time stamping.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
skb_tx_timestamp() does not report software time stamp
if SKBTX_IN_PROGRESS is set. According to timestamping.txt
software time stamps are a fallback and should not be
generated if hardware time stamp is provided.
Move call to skb_tx_timestamp() after setting
SKBTX_IN_PROGRESS.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
tx_hwtstamp_skb is always set before work is scheduled,
work is cancelled before tx_hwtstamp_skb is set to NULL.
PTP work cannot ever see tx_hwtstamp_skb set to NULL.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hardware may fail to report time stamp e.g.:
- when hardware time stamping is not enabled
- when time stamp is requested shortly after ifup
Timeout time stamp reading work to prevent it from
scheduling itself indefinitely. Report timeout events
via system log and device stats.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need to print this info unless at FD message level.
Change-ID: I329efdd8e754a0ea0669ec04d12e03db02e6b76e
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To use for Flow Director specific messages.
Change-ID: I69e39a410aa2661f8fd1ed6af0126fa4c335cb77
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure the VSI has a netdev before trying to use it
in the debugfs netdev_ops commands.
Change-ID: I2d744fc0c32b3226534ce2cde171d9675c5440a6
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There were two spaces between return and the value, we only need one.
Change-ID: Iaa42c33f50d8d149cdf1a4c9c1902295bfd991c4
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With this change we can drop a flow if we wanted to.
Change-ID: I222b1ae960e61a31965bafe3159a95099e70c7d2
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Function add_del_fdir was used and implemented only for add. So change the name
and drop a parameter.
Change-ID: Icf2c6c3bbd4fd00cf8d9613a3f6d8c08e0f8e288
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver needs to verify the eeprom checksum and firmware crc status bits,
and shutdown the driver if they fail. This code stops the processing of traffic,
but doesn't kill the PF netdev so that the NVMUpdate process should still have a
chance at fixing the image. The eeprom is checked on driver load and after an
EMP reset, the latter of which should be generated after an NVMUpdate.
Change-ID: I34deef21d2e16bf5a43c603cf8af27e6a29dc9d2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It's annoying to search for a matching alloc and free set of function calls
when they don't use the same framework for the name of the functions. Fix
that up in the case of alloc and free of vsi queue vectors.
i40e_vsi_free_q*
i40e_vsi_alloc_q*
Change-ID: I510eb863a0fbe405312bebea55c2846c76285e6d
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Tx watchdog handler runs in interrupt context, so it would cause an
oops when sending an admin queue message to request a reset, because the
admin queue functions use spinlocks.
Instead, set a flag and let the reset task handle sending the request.
Change-ID: I65879470b72963d9c308edfb8f45ac4fbba2c14f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We currently delete ATR filter on FIN alone, delete on RST as well.
Change-ID: Ie7cae5d1046b9d1d4a0d6ef5bdbf41224c3dade6
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
bfin_mdiobus_reset() does nothing useful and is optional for the MDIO
bus code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
r6040_mdiobus_reset() does nothing useful and is optional for the MDIO
bus code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ftgmac100_mdiobus_reset() does nothing useful and is optional for the
MDIO bus code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sun4i_mdio_reset() does nothing useful and is optional for the MDIO bus
code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xemaclite_mdio_reset() does nothing useful and is optional for the MDIO
bus code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
orion_mdio_reset() does nothing useful and is optional for the MDIO bus
code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fs_enet_fec_mii_reset() does nothing useful and is optional for the MDIO
bus code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_enet_mdio_reset() does nothing useful and is optional for the MDIO
bus code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethoc_mdio_reset() does nothing useful and is optional for the MDIO bus
code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dnet_mdio_reset() does nothing useful and is optional for the MDIO bus
code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macb_mdio_reset() does nothing useful and is optional for the MDIO bus
code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_mdio_reset() does nothing useful and is optional for the MDIO bus
code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
greth_mdio_reset() does nothing useful and this function is optional for
the MDIO bus code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the UniMAC block is configured to forward the CRC as part of the
Ethernet frame (priv->crc_fwd_en, set by default), enabling the hardware
RX checksum block unveiled that the dma_rxchk_bit was never set in the
per-packet status bits (dma_flag in bcmgenet_desc_rx). This would make
the chksum_ok variable to be never set to 1, and the networking stack
would have to compute the packet checksums, which takes a substantial
amount of time.
In order for the RXCHK block to properly compute the packet checksum in
hardware, we also need to set the RBUF_SKIP_FCS bit accordingly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The second parameter of __mlx4_init_one() is used to identify whether the
pci_dev is a PF or VF. Currently, when it is invoked in mlx4_pci_slot_reset()
this information is missed.
This patch match the pci_dev with mlx4_pci_table and passes the
pci_device_id.driver_data to __mlx4_init_one() in mlx4_pci_slot_reset().
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use del_timer_sync to ensure that the timer is stopped on all CPUs before
the driver exists.
This change was suggested by Thomas Gleixner
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
declarer name module_exit;
identifier ex;
@@
module_exit(ex);
@@
identifier r.ex;
@@
ex(...) {
<...
- del_timer
+ del_timer_sync
(...)
...>
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a race which happens by freeing an object on the stack.
Quoting Julius:
> The issue is
> that it calls usbnet_terminate_urbs() before that, which temporarily
> installs a waitqueue in dev->wait in order to be able to wait on the
> tasklet to run and finish up some queues. The waiting itself looks
> okay, but the access to 'dev->wait' is totally unprotected and can
> race arbitrarily. I think in this case usbnet_bh() managed to succeed
> it's dev->wait check just before usbnet_terminate_urbs() sets it back
> to NULL. The latter then finishes and the waitqueue_t structure on its
> stack gets overwritten by other functions halfway through the
> wake_up() call in usbnet_bh().
The fix is to just not allocate the data structure on the stack.
As dev->wait is abused as a flag it also takes a runtime PM change
to fix this bug.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Reported-by: Grant Grundler <grundler@google.com>
Tested-by: Grant Grundler <grundler@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 370d4a26 "bnx2x: Create workqueue for IOV related tasks" breaks bnx2x
compilation when CONFIG_BNX2X_SRIOV is not set - "multiple definition of
`bnx2x_schedule_iov_task'".
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
update description in Kconfig to state rtl8180 driver
now supports also rtl8187se cards
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Finally make rtl8187se works (hopefylly).
This patch adds PCI ID for rtl8187, updates copyright notes and
updates MODULE_DESCRIPTION.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add case to detect the rtl8187se card and its RF frontend.
In this case set also accordingly mac80211 queue number.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a new function to configure AC parameters for TX queues
on rtl8187se cards, and hook it onto mac80211 in order to enable
WMM support.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MSR register for rtl8187se must always have ENEDCA flag set.
Write it accordingly when updated on BSS change.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds ERP configuration support for rtl8187se to the
existing ERP configuration function.
It needs a different register offset and it must not apply
rtl8185 workaround.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jon Mason