- spec->hp_detect has to be overridden in HDA_FIXUP_ACT_PARSE, not in
PRE_PARSE.
- Remove err == 0 check but return directly -EINVAL from
stac92xx_parse_auto_config()
- Set spec->default_polarity for 92HD71bxx
- Some code shuffles
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A new flag to skip the auto-mute handling in the generic parser, just
like suppress_auto_mic flag. It has to be set before calling
snd_hda_gen_parse_auto_config().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* test/hda-gen-parser:
ALSA: hda - Make sure fill_all_dac_nids is called for digital only codecs
ALSA: hda - force different capture controls if amp caps differ
ALSA: hda - do not add non-existing Mic boost controls
ALSA: hda - initialize channel counts correctly
ALSA: hda - fix wrong adc_idx in generic parser
ALSA: hda - Check array bounds in get_input_path
ALSA: hda - Add prefer_hp_amp flag to hda_gen_spec
ALSA: hda - fix OOPS in hda_mark_cmd_cache_dirty
ALSA: hda - Check pincap while parsing the configuration
Otherwise no PCM will be built for codecs without analog I/O.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Otherwise setting the capture volume for amps will be weird and
inconsistent (it will try to set values outside the range of the
second amp based on capabilities of the first amp).
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the input node does not have any volume capable input amp,
don't add such a control.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Even a single DAC can output two channels, so the channel count
is twice the number of DACs.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We use knew->index for adc_idx when we create "Capture Volume" and
"Capture Switch", so use the same to retrieve adc_idx.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With HDSP_TOGGLE_SETTING in place, these functions are no longer
required. Removing them makes the code DRY and considerably shorter.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDSP_TOGGLE_SETTING and its corresponding functions allow to change
settings in the control register. Instead of using the specialised
functions, use the generic code to make the code DRY.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver contains multiple similar functions that change only a single
bit in the control register, only the bit position varies.
This patch implements a generic function to toggle a certain bit
position that will be used to replace the old code.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current iobox detection code reportedly fails for various users, so
simply do what the Win32 driver does instead.
Patch originally by Karl Grill <kgrill@chello.at> and then modified to
comply with kernel coding guidelines + current HEAD.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new flag to indicate whether HP amp is turned on as default for
speaker or line-outs, and enable this for ALC260 codec, as many
machines with this codec require the HP amp even for speakers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When "alsactl restore" is performed on HDMI codecs, it tries to
restore the channel map value since the channel map controls are
writable. But hdmi_chmap_ctl_put() returns -EBADFD when no PCM stream
is assigned yet, and this results in an error message from alsactl.
Although the error is harmless, it's certainly ugly and can be
regarded as a regression.
As a workaround, this patch changes the return code in such a case to
be zero for making others happy. (A slight excuse is: when the chmap
is changed through the proper alsa-lib API, the PCM status is checked
there anyway, so we don't have to be too strict in the kernel side.)
Cc: <stable@vger.kernel.org> [v3.7+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of checking the codec SSID in find_mute_led_cfg() for HP Mini
110, set the proper spec->default_polairty in the fixup table.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCI vendor ID check in find_mute_led_cfg() is now superfluous
because the function is called in the fixup table entries of HP
machines.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Finally all codecs in patch_sigmatel.c have been converted to use the
standard fixup helpers. This change also includes trivial cleanups
like the call of common setup for GPIO LED or the removal of unused
function.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This one is rather a simple conversion. The fixups for Dell machines
are implemented by fixup functions in the end.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This time, the only intrusive changes are for HP machines.
As the mute LED fixup and the bass speaker switch are required only
for HP machines, we can move these checks into the fixup entries; the
former is applied generically to all HP machines while the latter for
only certain models.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sometimes (or rather often) BIOS sets the pin default configurations
obviously wrongly. Looking through these failures, one common pattern
is to enable some dead pins that are usually marked as speaker pins.
In such a case, we can skip them if the pins don't have the output
capability.
In this patch, add a check for the valid pin cap bit for each parsed
pin, and filter out when it's invalid.
The fix was originally suggested by Raymond Yau.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This conversion is a bit tricky. Since STAC927x may take two
different volume-knob initialization values depending on the model, a
new flag, spec->volknob_init, is introduced to indicate whether it's
the standard volume-knob initialization or not.
Also, Dell BIOS model is now directly mapped onto the fixup table
instead of parsing in the function. This resulted in a new model ref,
STAC_927X_DELL_BIOS_SPDIF, which is a chained entry.
Also, for reducing the fixups, virtual entries like
STAC_927X_DELL_DMIC and STAC_D965_VERBS are introduced.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rather straightforward conversion, except for ones for Intel Mac.
As Intel Mac have only unique codec SSIDs, we need to remap the fixup
again for the codec SSID and call the new fixup there.
Also, we can reduce model enums like STAC_MACMINI, which are model
aliases for backward compatibility, since they can be pointed directly
via hda_model_fixup table.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add names of the clock sources for the M-Audio Fast Track
C400.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Attain constant real-world latency by skipping 16 data packets.
The number of packets to be skipped was found by trial and error.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Taking another look at the C400 descriptors, I see now that there is
a clock selector (0x80) for this device.
Right now, the clock source points to the internal clock (0x81), which
is also valid. When the external clock source (0x82) is selected in the
mixer, and the rates mismatch (if it's free-running it is fixed to
48KHz), xruns will occur.
Set the clock ID to the clock selector unit (0x81), which then
allows the validation code to function correctly.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A patch in the 3.2 kernel caused regression with hotplugging the
M-Audio Fast track pro, or sound after suspend. I don't have the
device so I haven't done a full analysis, but it seems userspace
(both udev and pulseaudio) got confused when a card was created,
immediately destroyed, and then created again.
However, at least one person in the bug report (martin djfun)
reports that this patch resolves the issue for him. It also leaves
a message in the log:
"snd-usb-audio: probe of 1-1.1:1.1 failed with error -5" which is
a bit misleading. It is better than non-working audio, but maybe
there's a more elegant solution?
BugLink: https://bugs.launchpad.net/bugs/1095315
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Yet another step forward. As all features for VIA codecs have been
implemented in the generic driver, we can move on to migrate the VIA
codec parser, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the support for the generic auto-parser to AD codec
driver. For AD1988, the old code is replaced simply with the new
generic parser. For other codecs, new model "auto" is added and
directed to use the generic parser.
No fixup codes have been implemented yet as of now. Eventually we'd
replace each static quirk with the generic parser + fixup.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just shuffle the codes and add ifdefs for testing to drop the static
quirk codes from patch_conexant.c.
By commenting out ENABLE_CXT_STATIC_QUIRKS define at the beginning of
the file, you can disable the whole static codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This time, the target is Cirrus codec. Its parser is a subset of
generic parser, so we can migrate fully with it now.
The only tricky part is the handling of SPDIF automute.
Cirrus driver sets the SPDIF out plug over the headphone. As a
workaround, set spec->gen.master_mute for toggling the headphone (and
other) mute.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CA0110 codec is a fairly straightforward hardware implementation,
and we can use the generic parser almost as is.
Just set spec->multi_cap_vol flag to follow the current behavior.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the old parser code for C-Media auto-parser with the latest
generic parser. For compatibility reason, the static bindings are
still left, but they could be cleaned up in future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The pincfgs, init_verbs and hints set by sysfs or patch might be
changed dynamically on the fly, thus we need to protect it.
Add a simple protection via a mutex.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As David Henningsson recently suggested, some HP laptops use an unused
mic pin for controlling a mute LED, and this information is provided
via DMI string "HP_Mute_LED_X_Y" string. This patch adds the generic
support for such cases, as we've already done in patch_sigmatel.c.
This is applied generically to all devices with ID 0x103c.
But as we don't know whether the device 103c:1586 really contains
HP_Mute_LED_X_Y DMI string, still keep the static setup for this
device using the mic2 pin 0x19.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some fixups such as setting the flags influencing on the parser
behavior should be applied before actually parsing the tree.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Try to recover from the regression: set the HP amp for the speaker and
add the hp jack mode enum as default.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the enum controls for changing the headphone amp bits of output
jacks, such as "Headphone Jack Mode". This feature isn't enabled as
default, so far, unless spec->add_out_jack_modes flag is set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a multi-io jack is switched to another direction, call the
automute and autoswitch update functions, as this jack won't be used
as the headphone or the mic jack that may turn off others.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new fixup type, HDA_FIXUP_PINCTLS, for overriding the pinctl
values of the given pins. It takes the same array of struct pintbl
like HDA_FIXUP_PINS, but each entry contains the pinctl value instead
of the pin default config value.
This patch also replaces the corresponding codes in patch_realtek.c.
Without this change, the direct call of verbs may be overridden again
by the later call of pinctl restoration by the driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now the whole codebase has been changed from the earlier kernels, it
makes little sense to keep these aliases. Simply replace with the
official names.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a jack is retasked as a different direction (e.g. a mic jack is
used as a CLFE output), such a jack shouldn't be counted as the target
for the automatic jack switching. Skip the automute or the autoswitch
when the current pinctl direction is different from what we suppose.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new pin target accessors for managing the current pinctl
values in the generic parser. The pinctl values of all active pins
are once determined at the initialization phase, and stored via
snd_hda_codec_set_pin_target(). This will be referred again in the
codec init or resume phase to set the actual pinctl.
This value is kept while the auto-mute. When a line-out or a speaker
pin is muted by auto-mute, the driver simply disables the pin, but it
doesn't touch the cached pinctl target value. Upon unmute, this value
is used to restore the original pinctl in return.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check more strictly about the validity of pinctl values in
snd_hda_set_pin_ctl() and correct the wrong bits automatically.
Also provide the helper function to correct pinctl bits to codec
drivers.
This automatically fixes the invalid pinctl writes that are found in
a few Realtek fixups for NID 0x0f amp like ASUS A6Rp.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We already have the list of whole pin widgets and there is an unused
space in the list; let's use it for caching the current pinctl value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a DAC is reassigned from surrounds to front or ADCs are reduced
due to incomplete imux, we clear the path indices but the path
instances remain as is. Since the paths might be still referred
through the whole path list parsing (e.g. is_active_nid()), we should
clear these path instances as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since some codecs can choose the aamix as a capture source, we should
support it as well. When spec->add_stereo_mix_input flag is set, the
parser checks the availability of aamix as the input source, and adds
the paths automatically when possible.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the current parser code, the input_paths[] may become inconsistent
when some of detected ADCs are dropped due to incomplete inputs, since
the driver rearranges only adc_nids[] but doesn't touch input_paths[].
This patch fixes the issue, and also it optimizes the reachability
checks by simply referring to the parsed input_paths[] instead of
calling is_reachable() again for each connection.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of handling special cases in the caller side, give a proper
name string "Headphone Mic" from hda_get_autocfg_input_label() when
the headhpone jack pin is specified as an input.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The capture paths shouldn't contain the analog loopback mixer.
Pass a proper argument to exclude the aamix NID.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new flag spec->suppress_mic_auto_switch for codecs that don't
support unsol events properly like VT1708.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the default config value shows the connection AC_JACK_PORT_BOTH,
it's better to handle it as a speaker pin. This makes the behavior
consistent in snd_hda_get_pin_label() and snd_hda_parse_pin_defcfg().
There are only few old machines showing this attribute, and all of
them are actually fixed speaker pins, as far as I know.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit modifies the definition of snd_hda_parse_nid_path()
slightly, now with_aa_mix argument is changed to anchor_nid, so that
it can handle any NID generically as an anchor point to include or
exclude.
The with_aa_mix field in struct nid_path is removed again by this
change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The multi-io channels can vary not only from 1 to 6 but also may vary
from 6 to 8 or such. At the same time, there are more speaker pins
available than the primary output pins. So, we need three variables
to check: the minimum channel counts for primary outputs, the current
channel counts for primary outputs, and the minimum channel counts for
all outputs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of looking through paths with the dac -> pin connection at
each time, just pass the already parsed path index to
assign_out_path_ctls(). This simplifies the code a bit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The path indices must be reset at each evaluation of DAC assignment.
Otherwise the badness value will be wrongly calculated and mixers may
be inconsistently assigned.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Let is_jack_detectable() return true when the jack polling is enabled
for the codec. VT1708 uses the polling explicitly so we need to allow
it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new hook which is called at each PCM playback ops.
It can be used to control the codec-specific power-saving feature in
each codec driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The bind-volume workaround was introduced for simplifying the mixer
abstraction in the case where one or more pins of multiple outputs
lack of individual volume controls. This was essentially the case
like Acer Aspire 5935, which has 5.1 speakers and 5.1 (multi-io)
jacks although there are 5 DACs, so some of them must share a DAC.
However, the recent code rewrite changed the DAC assignment policy to
share with the same channel instead of binding to the front, thus
binding the volumes for all channels makes little sense now, rather
it's confusing. So in this patch, the ugly workaround is finally
dropped and simply create the volume control corresponding to the
parsed path position.
For dual headphones or 2.1 speakers with a shared volume control, it's
anyway bound to the same DAC if needed, so this change shouldn't bring
any practical difference.
And, as a good bonus, we can cut off the whole code handling the bind
volume elements.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When 5.1 or more multiple speakers with found but not enough DACs are
available, it's better to bind such pins to the DACs of the primary
outputs with the same channels rather than binding to the first DAC
(i.e. the front channel). For the cases with two speaker pins, it's
rather regarded as front + bass combination, thus it's more practical
to still bind to the front, though.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... like "Speaker Surround Playback Switch".
This fix had been already applied to patch_conexant.c but was
forgotten in other places, then migrated to hda_generic.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For codecs that have individual routes going through a loopback mixer
(like VIA codecs), we need to provide an explicit switch to choose
whether the output goes through mixer or directly from DAC.
This patch adds the check for such paths and creates "Loopback Mixing"
enum control when available.
It won't influence on codecs like Realtek or others where the loopback
mixer is connected independently from the primary output routes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The output paths including aamix should be parsed only for the first
output. The surround paths including aamix must be wrong, since it
would mix all streams, i.e. all channels would be mixed into a single
and multiplexed again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Call the path activation for the digital input pin properly, not only
setting the pin control. Also add spec->digin_path for keeping the
path index.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of search for the path with the certain route at each time,
keep the path index for each output and loopback, and just use it when
referred.
In this implementation, the path index number begins with one, not
zero (although I've been writing in C over decades). It's just to
make the check for uninitialized values easier.
So far, the input paths aren't handled with indices yet, but still
picked up via snd_hda_get_nid_path() at each time.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When speakers are chosen as the the primary output during evaluation,
we did some tricks to assign the possible multi-io jacks with a
certain offset value to multi_out dacs. This was a workaround for the
case with multiple speakers like Acer Aspire. But this is quite ugly
at the same time and the resultant code is hard to understand. More
badly, it works wrongly for 2.1 speakers like Apple iMac91.
In this patch, instead of fiddling with the offset to multi_out dacs,
simply add a certain badness number if headphone(s) + multi-ios are
possible. This simplify the code a bit, and it's more robust.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the requested path has been already added, return the existing path
instance instead of adding a duplicated instance.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the paths are created in map_singles(), we don't have to
re-create new paths in try_assign_dacs(). Just evaluate the badness
and skip to the next item.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set path->active flag at the path creation time and let the paths
initialized according to the current path->active state in
set_output_and_unmute(). This allows to modify the active flag of
some output paths dynamically, e.g. switching the front output route
with or without aamix like patch_via.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
activate_amp() in the generic parser checks whether the given NID is
included in any active paths and skips it if found. This was a
workaround for avoiding disabling the widgets in the active paths when
one path is disabled, thus it shouldn't be applied to the case for
path activation. Due to this wrong check, some analog loopback paths
haven't been initialized correctly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Manage the connection list cache using linked lists instead of
snd_array, and revive snd_hda_get_conn_list() again, so that we don't
have to keep the expanded values locally.
This will reduce the stack usage by recursive call of
snd_hda_get_conn_index() or parse_nid_path() of the generic parser.
The list management doesn't include any mutex protection, thus the
caller needs to take care of race appropriately.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Yet another broken hardware workaround: there are hardware indicating
the inverted jack detection bit result.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the new flag, codec->inv_eapd, indicating that the EAPD
implementation is inverted.
There are always broken hardware in the world.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similar like the implementation in patch_analog.c and patch_via.c,
the generic parser can provide the independent HP PCM stream now.
It's enabled when spec->indep_hp is set by the caller while parsing.
Currently no dynamic PCM switching as in patch_via.c is implemented
yet. The control returns -EBUSY when the value is changed during PCM
operations.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai