While trying to suspend the mmc host there could still be
ongoing requests that we need to wait for. At the same time
a device driver must respond to a suspend request rather quickly.
Instead of potentially wait "forever" by claiming the host we now
"try" to claim the host instead. If it fails, -EBUSY is returned.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Table 6-2: CCCR bit Definitions, address 00h. Part E1 SDIO Simplified
Specification Version 3.00, Feb. 25, 2011.
This patch has been tested with Marvell WLAN device SD8797.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Here is Essential conditions to indicate Version 3.00 Card
(SD_SPEC=2 and SD_SPEC3=1) :
(1) The card shall support CMD6
(2) The card shall support CMD8
(3) The card shall support CMD42
(4) User area capacity shall be up to 2GB (SDSC) or 32GB (SDHC)
User area capacity shall be more than or equal to 32GB and
up to 2TB (SDXC)
(5) Speed Class shall be supported (SDHC or SDXC)
So even if SD card doesn't support any of the newly defined
UHS-I bus speed mode, it can advertise itself as SD3.0 cards
as long as it supports all the essential conditions of
SD3.0 cards. Given this, these type of cards should atleast
run in High Speed mode @50MHZ if it supports HS.
But current initialization sequence for SD3.0 cards is
such that these non-UHS-I SD3.0 cards runs in Default
Speed mode @25MHz.
This patch makes sure that these non-UHS-I SD3.0 cards run
in High Speed Mode @50MHz.
Tested this patch with SanDisk Extreme SDHC 8GB Class 10 card.
Reported-by: "Hiremath, Vaibhav" <hvaibhav@ti.com>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
HPI command is defined in eMMC4.41.
This feature is important for eMMC4.5 devices.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds cache feature of eMMC4.5 Spec.
If device supports cache capability, host can utilize some specific
operations.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch will apply the generic CMD6 timeout to switch command
for power class.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC v4.5 supports the DISCARD feature (CMD38). It's different from
trim and there's no check bit. Currently it's only supported at v4.5.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the v4.5, there's no secure erase & trim support.
Instead it supports the sanitize feature.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for the power off notify feature, available in
eMMC 4.5 devices. If the host has support for this feature, then the
mmc core will notify the device by setting the POWER_OFF_NOTIFICATION
byte in the extended csd register with a value of 1 (POWER_ON).
For suspend mode short timeout is used, whereas for the normal poweroff
long timeout is used.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
All the files using printk function for displaying kernel messages
in the mmc driver have been replaced with corresponding macro.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
EXT_CSD[248] includes the default maximum timeout for CMD6.
This field is added at eMMC4.5 Spec. And it can be used for default
timeout except for some operations which don't define the timeout
(i.e. background operation, sanitize, flush cache) in eMMC4.5 Spec.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_request_done() is sometimes called from interrupt or other atomic
context. Mostly all mmc_request_done() does is complete(), however it
contains code to retry on error, which uses ->request(). As the error
path is certainly not performance critical, this may be moved to the
waiting function mmc_wait_for_req_done().
This allows ->request() to use runtime PM get_sync() and guarantee it
is never in an atomic context.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit "mmc: add module param to set fault injection attributes" adds
a module_param to this file. But it is relying on the old implicit
"module.h is everywhere" behaviour, and without the explicit include
of moduleparam.h, the pending module.h split up produces this error:
core/debugfs.c:28:35: error: expected ')' before numeric constant
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
It allows gerneral purpose partitions in MMC Device. And I try to simply
make mmc_blk_alloc_parts using mmc_part structure suggested by Andrei
Warkentin. After patching, we see general purpose partitions like this:
> cat /proc/partitions
179 0 847872 mmcblk0
179 192 4096 mmcblk0gp3
179 160 4096 mmcblk0gp2
179 128 4096 mmcblk0gp1
179 96 1052672 mmcblk0gp0
179 64 1024 mmcblk0boot1
179 32 1024 mmcblk0boot0
Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Andrei Warkentin <awarkentin@vmware.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
f39b2dd9d ("mmc: core: Bus width testing needs to handle suspend/resume")
added code to only compare read-only ext_csd fields in bus width testing
code, yet it's comparing some fields that are never set.
The affected fields are ext_csd.raw_erased_mem_count and
ext_csd.raw_partition_support.
Signed-off-by: Andrei Warkentin <andrey.warkentin@gmail.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds the power class selection feature available for mmc
versions 4.0 and above. During the enumeration stage before switching
to the lower data bus, check if the power class is supported for the
current bus width. If the power class is available then switch to the
power class and use the higher data bus. If power class is not supported
then switch to the lower data bus in a worst case.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Replace setup("fail_mmc_request") and faulty "ifdef KERNEL" with
a simple module_param(). The module param mmc_core.fail_request
may be used to set the fault injection attributes during boot time
or module load time.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This is a minor fix. It makes mmc_ios_show print proper string when the
host's timing is one of the newly added UHS-I modes.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For cards that support hardware reset (just eMMC), try a reset and
retry before returning an I/O error. However this is not done for
ECC errors and is never done twice for the same operation type
(READ, WRITE, DISCARD, SECURE DISCARD) until that type of operation
again succeeds.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
eMMC's may have a hardware reset line. This patch provides a
host controller operation to implement hardware reset and
a function to reset and reinitialize the card. Also, for MMC,
the reset is always performed before initialization.
The host must set the new host capability MMC_CAP_HW_RESET
to enable hardware reset.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The err condition in post_req() is set to undo a call made to pre_req()
that hasn't been started yet. The err condition is not set if an MMC
request returns an error.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Earlier all cards where initiated with bus mode set as OPENDRAIN, and then
later switched to PUSHPULL. According to the MMC/SD/SDIO specifications
only MMC cards use OPENDRAIN during init. For both SD and SDIO the bus
mode shall be PUSHPULL before attempting to init the card.
The consequence of having incorrect bus mode can lead to not being able
to detect the card. Therefore the default behavior have now been changed
to PUSHPULL in mmc_power_up, and will only be temporarily switched when
trying to attach or init a MMC card.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Ulf HANSSON <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Adds a quirk which can be turned on for SDIO devices that do not support
512 byte requests in byte mode during CMD53. These requests will always
be sent in block mode instead.
This patch also enables this quirk for ST-Ericsson CW1200 WLAN device.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Ulf HANSSON <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
During a rescan operation mmc_attach(sd|mmc|sdio) functions are
called. The error handling in these function can trigger a detach
of the bus, which also meant a power off. This is not notified by
the rescan operation which then continues to the next attach function.
If a power off has been done, the framework must never send any
new commands to the host driver, without first doing a new power up.
This will most likely trigger any host driver to hang.
Moving power off out of detach and instead handle power off
separately when it is actually needed, solves the issue.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Put MMC to sleep if it supports SLEEP/AWAKE (CMD5) in the mmc suspend
so that Vcc (NAND core) can be cut to minimize power consumption.
eMMC put into SLEEP can respond to CMD0 or H/W reset or CMD5.
Current implemention on resume from suspend relies on CMD0 in
mmc_init_card to get out of SLEEP mode.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Venkatraman S <svenkatr@ti.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Stress-testing the runtime power management of libertas_sdio
through a rmmod/insmod loop revealed that it is quite easy to
cause an ETIMEDOUT failure in mmc_sdio_power_restore() leading to:
libertas_sdio: probe of mmc1:0001:1 failed with error -16
Experimentation shows that a very short delay (100us) is needed in
the power down path before the card can be successfully booted again.
We know that this setup is lacking poweroff clamps on the card's power
lines, but as only a short delay is needed, apply this unconditionally.
Also bump up to 1ms sleep for extra legroom.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix the sparse warning output "warning: Using plain integer as NULL pointer"
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Now that we have improved the runtime power management powerup/powerdown
code, we believe that MMC_CAP_POWER_OFF_CARD is no longer necessary:
runtime PM should now work everywhere.
The only hard evidence for introducing MMC_CAP_POWER_OFF_CARD was the
Marvell sd8686 wifi chip, which was believed to require external gpio
manipulation which wasn't supported by some boards.
After further investigation it was realized (and confirmed by Marvell
folks) that sd8686 requirements can be fulfilled by changing the reset
sequence itself, even if no external gpio is manipulated.
For further information, see the following thread:
http://www.mail-archive.com/linux-mmc@vger.kernel.org/msg04289.html
Enable this trivially for a release or two. If no problems are reported,
we will follow up with a more extensive patch to remove this flag
altogether. If problems are reported, we can look at whitelist/blacklist
possibilities as before.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This adds support to inject data errors after a completed host transfer.
The mmc core will return error even though the host transfer is successful.
This simple fault injection proved to be very useful to test the
non-blocking error handling in the mmc_blk_issue_rw_rq().
Random faults can also test how the host driver handles pre_req()
and post_req() in case of errors.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_sd_init_uhs_card function sets the driver type, current limit
and bus speed mode on card as well as on host controller side.
Currently bus speed mode is set by sending CMD6 to card and
immediately setting the timing mode in host controller. But
then before initiating tuning sequence, it also tries to set
current limit by sending CMD6 to card which results in data
timeout errors in controller if bus speed mode is SDR50/SDR104 mode.
So basically bus speed mode should be set only after current limit
is set in the card and immediately after setting the bus speed mode,
tuning sequence should be initiated.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The default multithread workqueue can cause the same work to be executed
concurrently on a different CPUs. This isn't really suitable for clock
gating as it might already gated the clock and gating it twice results both
host->clk_old and host->ios.clock to be set to 0.
To prevent this from happening we use system_nrt_wq instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Chris Ball <cjb@laptop.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We have seen at least two different races when clock gating kicks in in a
middle of ios structure update.
First one happens when ios->clock is changed outside of aggressive clock
gating framework, for example via mmc_set_clock(). The race might happen
when we run following code:
mmc_set_ios():
...
if (ios->clock > 0)
mmc_set_ungated(host);
Now if gating kicks in right after the condition check we end up setting
host->clk_gated to false even though we have just gated the clock. Next
time a request is started we try to ungate and restore the clock in
mmc_host_clk_hold(). However since we have host->clk_gated set to false the
original clock is not restored.
This eventually will cause the host controller to hang since its clock is
disabled while we are trying to issue a request. For example on Intel
Medfield platform we see:
[ 13.818610] mmc2: Timeout waiting for hardware interrupt.
[ 13.818698] sdhci: =========== REGISTER DUMP (mmc2)===========
[ 13.818753] sdhci: Sys addr: 0x00000000 | Version: 0x00008901
[ 13.818804] sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000
[ 13.818853] sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
[ 13.818903] sdhci: Present: 0x1fff0000 | Host ctl: 0x00000001
[ 13.818951] sdhci: Power: 0x0000000d | Blk gap: 0x00000000
[ 13.819000] sdhci: Wake-up: 0x00000000 | Clock: 0x00000000
[ 13.819049] sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
[ 13.819098] sdhci: Int enab: 0x00ff00c3 | Sig enab: 0x00ff00c3
[ 13.819147] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
[ 13.819196] sdhci: Caps: 0x6bee32b2 | Caps_1: 0x00000000
[ 13.819245] sdhci: Cmd: 0x00000000 | Max curr: 0x00000000
[ 13.819292] sdhci: Host ctl2: 0x00000000
[ 13.819331] sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000
[ 13.819377] sdhci: ===========================================
[ 13.919605] mmc2: Reset 0x2 never completed.
and it never recovers.
Second race might happen while running mmc_power_off():
static void mmc_power_off(struct mmc_host *host)
{
host->ios.clock = 0;
host->ios.vdd = 0;
[ clock gating kicks in here ]
/*
* Reset ocr mask to be the highest possible voltage supported for
* this mmc host. This value will be used at next power up.
*/
host->ocr = 1 << (fls(host->ocr_avail) - 1);
if (!mmc_host_is_spi(host)) {
host->ios.bus_mode = MMC_BUSMODE_OPENDRAIN;
host->ios.chip_select = MMC_CS_DONTCARE;
}
host->ios.power_mode = MMC_POWER_OFF;
host->ios.bus_width = MMC_BUS_WIDTH_1;
host->ios.timing = MMC_TIMING_LEGACY;
mmc_set_ios(host);
}
If the clock gating worker kicks in while we are only partially updated the
ios structure the host controller gets incomplete ios and might not work as
supposed. Again on Intel Medfield platform we get:
[ 4.185349] kernel BUG at drivers/mmc/host/sdhci.c:1155!
[ 4.185422] invalid opcode: 0000 [#1] PREEMPT SMP
[ 4.185509] Modules linked in:
[ 4.185565]
[ 4.185608] Pid: 4, comm: kworker/0:0 Not tainted 3.0.0+ #240 Intel Corporation Medfield/iCDKA
[ 4.185742] EIP: 0060:[<c136364e>] EFLAGS: 00010083 CPU: 0
[ 4.185827] EIP is at sdhci_set_power+0x3e/0xd0
[ 4.185891] EAX: f5ff98e0 EBX: f5ff98e0 ECX: 00000000 EDX: 00000001
[ 4.185970] ESI: f5ff977c EDI: f5ff9904 EBP: f644fe98 ESP: f644fe94
[ 4.186049] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[ 4.186125] Process kworker/0:0 (pid: 4, ti=f644e000 task=f644c0e0 task.ti=f644e000)
[ 4.186219] Stack:
[ 4.186257] f5ff98e0 f644feb0 c1365173 00000282 f5ff9460 f5ff96e0 f5ff96e0 f644feec
[ 4.186418] c1355bd8 f644c0e0 c1499c3d f5ff96e0 f644fed4 00000006 f5ff96e0 00000286
[ 4.186579] f644fedc c107922b f644feec 00000286 f5ff9460 f5ff9700 f644ff10 c135839e
[ 4.186739] Call Trace:
[ 4.186802] [<c1365173>] sdhci_set_ios+0x1c3/0x340
[ 4.186883] [<c1355bd8>] mmc_gate_clock+0x68/0x120
[ 4.186963] [<c1499c3d>] ? _raw_spin_unlock_irqrestore+0x4d/0x60
[ 4.187052] [<c107922b>] ? trace_hardirqs_on+0xb/0x10
[ 4.187134] [<c135839e>] mmc_host_clk_gate_delayed+0xbe/0x130
[ 4.187219] [<c105ec09>] ? process_one_work+0xf9/0x5b0
[ 4.187300] [<c135841d>] mmc_host_clk_gate_work+0xd/0x10
[ 4.187379] [<c105ec82>] process_one_work+0x172/0x5b0
[ 4.187457] [<c105ec09>] ? process_one_work+0xf9/0x5b0
[ 4.187538] [<c1358410>] ? mmc_host_clk_gate_delayed+0x130/0x130
[ 4.187625] [<c105f3c8>] worker_thread+0x118/0x330
[ 4.187700] [<c1496cee>] ? preempt_schedule+0x2e/0x50
[ 4.187779] [<c105f2b0>] ? rescuer_thread+0x1f0/0x1f0
[ 4.187857] [<c1062cf4>] kthread+0x74/0x80
[ 4.187931] [<c1062c80>] ? __init_kthread_worker+0x60/0x60
[ 4.188015] [<c149acfa>] kernel_thread_helper+0x6/0xd
[ 4.188079] Code: 81 fa 00 00 04 00 0f 84 a7 00 00 00 7f 21 81 fa 80 00 00 00 0f 84 92 00 00 00 81 fa 00 00 0
[ 4.188780] EIP: [<c136364e>] sdhci_set_power+0x3e/0xd0 SS:ESP 0068:f644fe94
[ 4.188898] ---[ end trace a7b23eecc71777e4 ]---
This BUG() comes from the fact that ios.power_mode was still in previous
value (MMC_POWER_ON) and ios.vdd was set to zero.
We prevent these by inhibiting the clock gating while we update the ios
structure.
Both problems can be reproduced by simply running the device in a reboot
loop.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Chris Ball <cjb@laptop.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
As per suggestion by Linus Walleij:
> If you think the names of the functions are confusing then
> you may rename them, say like this:
>
> mmc_host_clk_ungate() -> mmc_host_clk_hold()
> mmc_host_clk_gate() -> mmc_host_clk_release()
>
> Which would make the usecases more clear
(This is CC'd to stable@ because the next two patches, which fix
observable races, depend on it.)
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
It is not necessary to share the same notifier.h.
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: David Miller <davem@davemloft.net>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At http://www.mail-archive.com/linux-mmc@vger.kernel.org/msg08371.html
(thread: "mmc: sdio: reset card during power_restore") we found and
fixed a bug where mmc's runtime power management functions were not being
called. We have now also made improvements to the SDIO powerup routine
which could possibly mask this kind of issue in future.
Add debug messages to the runtime PM hooks so that it is easy to verify
if and when runtime PM is happening.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the case where a driver returns -ENOSYS from its suspend handler
to indicate that the device should be powered down over suspend, the
remove routine of the driver was not being called, leading to lots of
confusion during resume.
The problem is that runtime PM is disabled during this process,
and when we reach mmc_sdio_remove, calling the runtime PM functions here
(validly) return errors, and this was causing us to skip the remove
function.
Fix this by ignoring the error value of pm_runtime_get_sync(), which
can return valid errors. This also matches the behaviour of
pci_device_remove().
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Non default Drive Strength cannot be set automatically. It is a function
of the board design and only if there is a specific platform handler can
it be set. The platform handler needs to take into account the board
design. Pass to the platform code the necessary information.
For example: The card and host controller may indicate they support HIGH
and LOW drive strength. There is no way to know what should be chosen
without specific board knowledge. Setting HIGH may lead to reflections
and setting LOW may not suffice. There is no mechanism (like ethernet
duplex or speed pulses) to determine what should be done automatically.
If no platform handler is defined -- use the default value.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Previously there has only been one function mmc_wait_for_req()
to start and wait for a request. This patch adds:
* mmc_start_req() - starts a request wihtout waiting
If there is on ongoing request wait for completion
of that request and start the new one and return.
Does not wait for the new command to complete.
This patch also adds new function members in struct mmc_host_ops
only called from core.c:
* pre_req - asks the host driver to prepare for the next job
* post_req - asks the host driver to clean up after a completed job
The intention is to use pre_req() and post_req() to do cache maintenance
while a request is active. pre_req() can be called while a request is
active to minimize latency to start next job. post_req() can be used after
the next job is started to clean up the request. This will minimize the
host driver request end latency. post_req() is typically used before
ending the block request and handing over the buffer to the block layer.
Add a host-private member in mmc_data to be used by pre_req to mark the
data. The host driver will then check this mark to see if the data is
prepared or not.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some host controllers will not operate without a hardware
timeout that is limited in value. However large discards
require large timeouts, so there needs to be a way to
specify the maximum discard size.
A host controller driver may now specify the maximum discard
timeout possible so that max_discard_sectors can be calculated.
However, for eMMC when the High Capacity Erase Group Size
is not in use, the timeout calculation depends on clock
rate which may change. For that case Preferred Erase Size
is used instead.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
On reading the ext_csd for the first time (in 1 bit mode), save the
ext_csd information needed for bus width compare.
On every pass we make re-reading the ext_csd, compare the data
against the saved ext_csd data.
This fixes a regression introduced in 3.0-rc1 by 08ee80cc39
("mmc: core: eMMC bus width may not work on all platforms"), which
incorrectly assumed we would be re-reading the ext_csd at resume-
time.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The erase timeout calculation may depend on clock rate
which is zero if the clock is gated, so use
mmc_host_clk_rate() which allows for that case.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_sdio_power_restore() skips some steps that are performed in other
power-related codepaths which are necessary to fully reset the card.
Without this, runtime PM fails for SD8686 SDIO wifi on OLPC XO-1.5.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
After commit e1866b3 "PM / Runtime: Rework runtime PM handling
during driver removal" was introduced, the driver core stopped
incrementing the runtime PM usage counter of the device during
the invocation of the ->remove() callback.
This indirectly broke SDIO's runtime PM path during driver removal,
because no one calls _put_sync() anymore after ->remove() completes.
This means that the power of runtime-PM-managed SDIO cards is kept
high after their driver is removed (even if it was powered down
beforehand).
Fix that by directly calling _put_sync() when the last usage
counter is downref'ed by the SDIO bus.
Reported-and-tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (75 commits)
mmc: core: eMMC bus width may not work on all platforms
mmc: sdhci: Auto-CMD23 fixes.
mmc: sdhci: Auto-CMD23 support.
mmc: core: Block CMD23 support for UHS104/SDXC cards.
mmc: sdhci: Implement MMC_CAP_CMD23 for SDHCI.
mmc: core: Use CMD23 for multiblock transfers when we can.
mmc: quirks: Add/remove quirks conditional support.
mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver
mmc: sdhci-pxa: Add quirks for DMA/ADMA to match h/w
mmc: core: duplicated trial with same freq in mmc_rescan_try_freq()
mmc: core: add support for eMMC Dual Data Rate
mmc: core: eMMC signal voltage does not use CMD11
mmc: sdhci-pxa: add platform code for UHS signaling
mmc: sdhci: add hooks for setting UHS in platform specific code
mmc: core: clear MMC_PM_KEEP_POWER flag on resume
mmc: dw_mmc: fixed wrong regulator_enable in suspend/resume
mmc: sdhi: allow powering down controller with no card inserted
mmc: tmio: runtime suspend the controller, where possible
mmc: sdhi: support up to 3 interrupt sources
mmc: sdhi: print physical base address and clock rate
...
CMD19 -- The offical way to validate bus widths from the JEDEC spec
does not work on all platforms. Some platforms that use PCI/PCIe
to connect their SD controllers are known to fail.
If the quirk MMC_BUS_WIDTH_TEST is not defined we try to figure out
the bus width by reading the ext_csd at different bus widths and
compare this against the ext_csd read in 1 bit mode. If no ext_csd
is available we default to 1 bit operations.
Code has been tested on mmp2 against 8 bit eMMC and Transcend 2GB
card that is known to not work in 4 bit mode. The physical pins
on the card are not present to support 4 bit operation.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SD cards operating at UHS104 or better support SET_BLOCK_COUNT.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_rescan_try_freq() tries to init two times with the last frequency.
For example, if host->f_min is 400KHz, we see the message below:
mmc1: mmc_rescan_try_freq: trying to init card at 400000 Hz
mmc1: mmc_rescan_try_freq: trying to init card at 400000 Hz
Andy Ross says that he didn't try this code on a board with an f_min
that exactly matches one of the table entries, which explains why the
bug wasn't detected.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Andy Ross <andy.ross@windriver.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
eMMC voltage change not required for 1.8V. 3.3V and 1.8V vcc
are capable of doing DDR. vccq of 1.8v is not required.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
eMMC chips do not use CMD11 when changing voltage. Add extra
argument to call to indicate if CMD11 needs to be sent.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since the MMC_PM_KEEP_POWER flag should be set on each suspend,
it should also cleared on each resume.
Upon resuming, we have to know if power was kept
(for re-initialization, etc.), so clear it just after resuming.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If there is only 1 function interrupt registered it is possible to
improve performance by directly calling the irq handler and avoiding
the overhead of reading the CCCR registers.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to the Host Controller spec v3.00, setting Preset Value Enable
in the Host Control2 register lets SDCLK Frequency Select, Clock Generator
Select and Driver Strength Select to be set automatically by the Host
Controller based on the UHS-I mode set. This patch enables this feature.
Since Preset Value Enable makes sense only for UHS-I cards, we enable this
feature after successfull UHS-I initialization. We also reset Preset Value
Enable next time before initialization.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host Controller needs tuning during initialization to operate SDR50
and SDR104 UHS-I cards. Whether SDR50 mode actually needs tuning is
indicated by bit 45 of the Host Controller Capabilities register.
A new command CMD19 has been defined in the Physical Layer spec
v3.01 to request the card to send tuning pattern.
We enable Buffer Read Ready interrupt at the very begining of tuning
procedure, because that is the only interrupt generated by the Host
Controller during tuning. We program the block size to 64 in the
Block Size register. We make sure that DMA Enable and Multi Block
Select in the Transfer Mode register are set to 0 before actually
sending CMD19. The tuning block is sent by the card to the Host
Controller using DAT lines, so we set Data Present Select (bit 5) in
the Command register. The Host Controller is responsible for doing
the verfication of tuning block sent by the card at the hardware
level. After sending CMD19, we wait for Buffer Read Ready interrupt.
In case we don't receive an interrupt after the specified timeout
value, we fall back on fixed sampling clock by setting Execute
Tuning (bit 6) and Sampling Clock Select (bit 7) of Host Control2
register to 0. Before exiting the tuning procedure, we disable Buffer
Read Ready interrupt and re-enable other interrupts.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since only UHS-I cards respond with S18A set in response to ACMD41,
we set the card as ultra-high-speed after successfull initialization.
We need to decide whether a card is SDXC based on the C_SIZE field
of CSDv2.0 register. According to Physical Layer spec v3.01, the
minimum value of C_SIZE for SDXC card is 00FFFFh.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
We decide on the current limit to be set for the card based on the
Capability of Host Controller to provide current at 1.8V signalling,
and the maximum current limit of the card as indicated by CMD6
mode 0. We then set the current limit for the card using CMD6 mode 1.
As per the Physical Layer Spec v3.01, the current limit switch is
only applicable for SDR50, SDR104, and DDR50 bus speed modes. For
other UHS-I modes, we set the default current limit of 200mA.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for setting UHS-I bus speed mode during UHS-I
initialization procedure. Since both the host and card can support
more than one bus speed, we select the highest speed based on both of
their capabilities. First we set the bus speed mode for the card using
CMD6 mode 1, and then we program the host controller to support the
required speed mode. We also set High Speed Enable in case one of the
UHS-I modes is selected. We take care to reset SD clock before setting
UHS mode in the Host Control2 register, and then re-enable it as per
the Host Controller spec v3.00. We then set the clock frequency for
the UHS-I mode selected.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for setting driver strength during UHS-I
initialization procedure. Since UHS-I cards set S18A (bit 24) in
response to ACMD41, we use this as a base for UHS-I initialization.
We modify the parameter list of mmc_sd_get_cid() so that we can
save the ROCR from ACMD41 to check whether bit 24 is set.
We decide whether the Host Controller supports A, C, or D driver
type depending on the Capabilities register. Driver type B is
suported by default. We then set the appropriate driver type for
the card using CMD6 mode 1. As per Host Controller spec v3.00, we
set driver type for the host only if Preset Value Enable in the
Host Control2 register is not set. SDHCI_HOST_CONTROL has been
renamed to SDHCI_HOST_CONTROL1 to conform to the spec.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SD cards which conform to Physical Layer Spec v3.01 can support
additional Bus Speed Modes, Driver Strength, and Current Limit
other than the default values. We use CMD6 mode 0 to read these
additional card functions. The values read here will be used
during UHS-I initialization steps.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host Controller v3.00 adds another Capabilities register. Apart
from other things, this new register indicates whether the Host
Controller supports SDR50, SDR104, and DDR50 UHS-I modes. The spec
doesn't mention about explicit support for SDR12 and SDR25 UHS-I
modes, so the Host Controller v3.00 should support them by default.
Also if the controller supports SDR104 mode, it will also support
SDR50 mode as well. So depending on the host support, we set the
corresponding MMC_CAP_* flags. One more new register. Host Control2
is added in v3.00, which is used during Signal Voltage Switch
procedure described below.
Since as per v3.00 spec, UHS-I supported hosts should set S18R
to 1, we set S18R (bit 24) of OCR before sending ACMD41. We also
need to set XPC (bit 28) of OCR in case the host can supply >150mA.
This support is indicated by the Maximum Current Capabilities
register of the Host Controller.
If the response of ACMD41 has both CCS and S18A set, we start the
signal voltage switch procedure, which if successfull, will switch
the card from 3.3V signalling to 1.8V signalling. Signal voltage
switch procedure adds support for a new command CMD11 in the
Physical Layer Spec v3.01. As part of this procedure, we need to
set 1.8V Signalling Enable (bit 3) of Host Control2 register, which
if remains set after 5ms, means the switch to 1.8V signalling is
successfull. Otherwise, we clear bit 24 of OCR and retry the
initialization sequence. When we remove the card, and insert the
same or another card, we need to make sure that we start with 3.3V
signalling voltage. So we call mmc_set_signal_voltage() with
MMC_SIGNAL_VOLTAGE_330 set so that we are back to 3.3V signalling
voltage before we actually start initializing the card.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allows appropriately-privileged applications to send CMD (normal) and ACMD
(application-specific; preceded with CMD55) commands to cards/devices on
the mmc bus. This is primarily useful for enabling the security
functionality built in to every SD card.
It can also be used as a generic passthrough (e.g. to enable virtual
machines to control mmc bus devices directly). However, this use case has
not been tested rigorously. Generic passthrough testing was only conducted
for a few non-security opcodes to prove the feasibility of the passthrough.
Since any opcode can be sent using this passthrough, it is very possible to
render the card/device unusable. Applications that use this ioctl must
have CAP_SYS_RAWIO.
Security commands tested on TI PCIxx12 (SDHCI), Sigma Designs SMP8652 SoC,
TI OMAP3621/OMAP3630 SoC, Samsung S5PC110 SoC, Qualcomm MSM7200A SoC.
Signed-off-by: John Calixto <john.calixto@modsystems.com>
Reviewed-by: Andrei Warkentin <andreiw@motorola.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Converts from:
struct mmc_request mrq;
memset(&mrq, 0, sizeof(struct mmc_request));
to:
struct mmc_request mrq = {0};
because it's shorter, as performant, and easier to work out whether
initialization has happened.
Signed-off-by: Chris Ball <cjb@laptop.org>
Converts from:
struct mmc_data data;
memset(&data, 0, sizeof(struct mmc_data));
to:
struct mmc_data data = {0};
because it's shorter, as performant, and easier to work out whether
initialization has happened.
Signed-off-by: Chris Ball <cjb@laptop.org>
Converts from:
struct mmc_command cmd;
memset(&cmd, 0, sizeof(struct mmc_command));
to:
struct mmc_command cmd = {0};
because it's shorter, as performant, and easier to work out whether
initialization has happened.
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_cmd_app did not zero out mmc_command on stack.
Reported-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allows device MMC boot partitions to be accessed. MMC partitions are
treated effectively as separate block devices on the same MMC card.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
CMD6 is an R1B-type command, where DAT is used as busy. Depending
on register written using CMD6, timeout value can be different
as per spec.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Renames erase_timeout to cmd_timeout_ms inside struct mmc_command.
First step to making host honor timeouts for non-data-transfer
commands. Cleans up erase timeout code.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The current mechanism is SDIO-only. This allows us to create
function-specific quirks, without creating messy Kconfig dependencies,
or polluting core/ with function-specific code.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
led_trigger_register_simple() allocates memory which must not be leaked
in the error-path of mmc_add_host. Move it past the only error-check in
the function.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The wl12xx device supports disconnecting the pull-up resistor on
CD/DAT[3] (pin 1) of the card.
Tell SDIO core to disconnect that resistor during card init,
since we don't need it at that point (and anyway all
hosts shall provide pull-up resistors on all data lines DAT[3:0]
as described in section 6 of the SD physical specification).
As a result, this may save some power, but it's also generally healthy
since it prevents both ends from pulling up that pin, which
results in undesirable asymmetric physical bus.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
006ebd5d introduced sdio_disable_cd(), which disconnects the pull-up
resistor on CD/DAT[3] (pin 1) of the card.
Make it possible to start using sdio_disable_cd() by introducing
MMC_QUIRK_DISABLE_CD.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Tell SDIO core to ignore the standard SDIO function interface
codes indicated by the wl1271. This is required because the
wl1271 erroneously indicates its first function as a standard
Bluetooth SDIO interface, and that drives btsdio mad.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Introduce MMC_QUIRK_NONSTD_FUNC_IF to ignore the "SDIO Standard Function
interface code" as indicated by the card's FBR, and instead treat all
functions as non-standard interfaces.
This is required to prevent standard drivers from facing
errors when trying to communicate with SDIO cards that erroneously
indicate standard function interface codes.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
6b5eda36 followed SDIO spec part E1 section 8, which states that
in case SDIO interrupts are being used to wake up a suspended host,
then it is required to switch to 1-bit mode before stopping the clock.
Before switching to 1-bit mode (or back to 4-bit mode on resume),
make sure that SDIO interrupts are really being used to wake the host.
This is helpful for devices which have an external irq line (e.g.
wl1271), and do not use SDIO interrupts to wake up the host.
In this case, switching to 1-bit mode (and back to 4-bit mode on resume)
is not necessary.
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_card_is_powered_resumed is a mouthful; instead, simply use
mmc_card_keep_power, which also better explains the purpose of
the macro.
Employ mmc_card_keep_power() where possible.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allows reliable writes to be used for MMC writes. Reliable writes are used
to service write REQ_FUA/REQ_META requests. Handles both the legacy and
the enhanced reliable write support in MMC cards.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
uBoot sometimes leaves eMMC pointing to the private boot partition.
Ensure we always start looking at the user partition.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Bruce Clemens <bpclemens@marvell.com>
Signed-off-by: Mark F. Brown <markb@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently there is a race in the MMC core between a card-detect
rescan work and the clock-gating work, scheduled from a command
completion. Fix it by removing the dedicated clock-gating mutex
and using the MMC standard locking mechanism instead.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fixes a cosmetic bug that affects printk() for SD-combo cards.
Reported-by: Prashanth Bhat <prashanth.bhat@manipal.net>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch is based on the commit "af51715079e7fb6b290e1881d63d815dc4de5011":
* Bugfix to that mmc_send_cxd_data() code: dma-to-stack is
unsafe/nonportable, so kmalloc a bounce buffer instead.
The driver may invalidate the mmc_card->csd when host driver uses dma.
So this subroutine also needs a kmalloc buffer.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
At power off, reset OCR mask to be the highest possible voltage
supported for the current mmc host.
This solves the re-initialization during the power up sequence.
The voltage may have been decreased due to the card accepts a lower
voltage than the voltage used during the initialization sequence.
We need to reset the voltage to by the host highest possible value
since according to specification the initialization must always be
done at high voltage.
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When using mmc_try_claim_host the corresponding release
function is mmc_do_release_host, which then also must
be exported.
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Reviewed-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
During redetection of a SDIO card, a request for a new card RCA
was submitted to the card, but was then overwritten by the old RCA.
This caused the card to be deselected instead of selected when using
the incorrect RCA. This bug's been present since the "oldcard"
handling was introduced in 2.6.32.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Reviewed-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Pawel Wieczorkiewicz <pawel.wieczorkiewicz@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some TOSHIBA MMC cards only support sector addressing even though the
size is < 2GB. According to JEDEC Spec JESD84-A441-1 the ocr register
(bits 30, 29) determine byte/sector mode. Use them.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sdio_reset sends a CMD52 to reset the sdio card. This is highly
recommended for sdio cards being reinitialized. Since we do not
know if the card is being reinitialized we just send the command.
SD/eMMC cards are supposed to ignore the CMD before the CMD0.
Document why we are doing this.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
So we know the implementation and prototypes agree with each other.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This sdio card supports having its sdio clock shutdown.
It is also not using the SDIO IRQ, but rather uses a side gpio irq.
Signed-off-by: Pierre Tardy <tardyp@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some sdio card are not following sdio standard, and do not work
when the sdio bus's clock is gated.
To keep functionnality for all legacy driver, we turn this quirk on
for every sdio card.
Drivers needs to disable the quirk manually when someone verifies that
their supported card works with clock gating.
Signed-off-by: Pierre Tardy <tardyp@gmail.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some cards have quirks valid for every platforms using current
platform quirk hooks leads to a lot of code and debug duplication.
So we inspire a bit from what exists in PCI subsystem and do our own
per vendorid/deviceid quirk. We still drop the complexity of the pci
quirk system (with special section tables, and so on).
That can be added later if needed.
Signed-off-by: Pierre Tardy <pierre.tardy@intel.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since mmc clock gating can also be used as a power gating
tip, it's better to put the led blinking after having
ungated the clock.
Signed-off-by: Pierre Tardy <pierre.tardy@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enhanced area feature is a new feature defined in eMMC4.4 standard. This
user data area provides higher performance/reliability, at the expense
of using twice the effective media space due to the area using SLC.
The MMC driver now reads out the enhanced area offset and size and adds
them to the device attributes in sysfs. Enabling the enhanced area can
only be done once, and should be done in manufacturing. To use this
feature, bit ERASE_GRP_DEF should also be set.
Documentation/ABI/testing/sysfs-devices-mmc describes the two new
attributes.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
30201e7f3 ("mmc: skip detection of nonremovable cards on rescan")
allowed skipping detection of nonremovable cards on mmc_rescan().
The intention was to only skip detection of hardwired cards that
cannot be removed, so make sure this is indeed the case by directly
checking for (lack of) MMC_CAP_NONREMOVABLE, instead of using
mmc_card_is_removable(), which is overloaded with
CONFIG_MMC_UNSAFE_RESUME semantics.
The user-visible symptom of the bug this patch fixes is that no
"mmc: card XXXX removed" message appears in dmesg when a card is
removed and CONFIG_MMC_UNSAFE_RESUME=y.
Reported-and-tested-by: Dmitry Shmidt <dimitrysh@google.com>
Reported-and-tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This fixes a bug introduced by 807e8e4067 ("mmc: Fix sd/sdio/mmc
initialization frequency retries") that prevented SDIO drivers from
performing SDIO commands in their probe routines -- the above patch
called mmc_claim_host() before sdio_add_func(), which causes a deadlock
if an external SDIO driver calls sdio_claim_host().
Fix tested on an OLPC XO-1.75 with libertas on SDIO.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Reviewed-and-Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The card is not always clocked and the clock frequency zero is perfectly
legal, thus this code in mmc_set_data_timeout() may cause a division by
zero. It will be triggered more often if you're using software clock
gating but can be triggered under other conditions too.
Reported-by: Pierre Tardy <tardyp@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This way, the probe function may register debugfs files if it wants to.
This fixes a bug with mmc_test where mmc_test_register_file_test() is
called before the card's debugfs dir exists, and so it fails.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Rewrite and clean up mmc_rescan() to properly retry frequencies lower
than 400kHz. Failures can happen both in sd_send_* calls and
mmc_attach_*. Break out "mmc_rescan_try_freq" from the frequency
selection loop. Symmetrize claim/release logic in mmc_attach_* API,
and move the sd_send_* calls there to make mmc_rescan easier to read.
Signed-off-by: Andy Ross <andy.ross@windriver.com>
Reviewed-and-Tested-by: Hein Tibosch <hein_tibosch@yahoo.es>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
With the bus-width test patch, mmc_set_bus_width*() isn't called properly
when the driver doesn't set MMC_CAP_BUS_WIDTH and no DDR mode.
This patch fixes the regression by moving the call up before the cap test.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since we make sure the clock is enabled in the mmc_host_clk_exit()
function we should expect a reference counter of 1, not 0.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some old MMC devices fail with the 4/8 bits the driver tries to use
exclusively. This patch adds a test for the given bus setup and falls
back to the lower bit mode (until 1-bit mode) when the test fails.
[Major rework and refactoring by tiwai]
[Quirk addition and many fixes by prakity]
Signed-off-by: Aries Lee <arieslee@jmicron.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In case of failure, mmc_attach_sdio() will power off the SD bus.
Power it up and reinitialize before trying SD memory detection.
Reported-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Upon system resume, SDIO core must reinitialize cards that were
powered off during suspend.
If the card had its power kept during suspend (and thus it is
'powered-resumed'), SDIO core performs only a limited reinitializing,
mainly needed to make sure that the card wasn't removed/replaced.
If a __nonremovable__ card is powered-resumed, we can safely skip the
reinitializing phase.
Note: 9b966aa (mmc: sdio: fully reconfigure oldcard on resume) removed
the bus width reconfiguration since mmc_sdio_init_card already does it.
It is brought back now in case mmc_sdio_init_card is skipped.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Initial SDIO runtime PM implementation took a conservative approach
of powering up cards (and fully reinitializing them) on system suspend,
just before the suspend handlers of the relevant drivers were executed.
To avoid redundant power and reinitialization cycles, this patch removes
this behavior: if a card is already powered off when system suspend kicks
in, it is left at that state.
If a card is active when a system sleep starts, everything is
straightforward and works exactly like before. But if the card was
already suspended before the sleep began, then when the MMC core powers
it back up on resume, its run-time PM status has to be updated to reflect
the actual post-system sleep status.
The technique to do that is borrowed from the I2C runtime PM
implementation (for more info see Documentation/power/runtime_pm.txt).
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_rescan() checks whether registered cards are still present before
skipping them, by calling the bus-specific ->detect() handler.
With buses that support runtime PM, the card may be powered off at
this point, so they need to be powered on and fully reinitialized before
->detect() executes.
This whole process is redundant with nonremovable cards; in those cases,
we can safely skip calling ->detect() and implicitly assume its success.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
JMicron 388 SD/MMC combo controller supports the 1.8V low-voltage for
SD, but MMC doesn't work with the low-voltage, resulting in an error
at probing.
This patch adds the support for multiple voltage mask per device type,
so that SD works with 1.8V while MMC forces 3.3V. Here new ocr_avail_*
fields for each device are introduced, so that the actual OCR mask is
switched dynamically.
Also, the restriction of low-voltage in core/sd.c is removed when the
bit is allowed explicitly via ocr_avail_sd mask.
This patch was rewritten from scratch based on Aries' original code.
Signed-off-by: Aries Lee <arieslee@jmicron.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch modifies the MMC core code to optionally call the set_ios()
operation on the driver with the clock frequency set to 0 (gate) after
a grace period of at least 8 MCLK cycles, then restore it (ungate)
before any new request. This gives the driver the option to shut down
the MCI clock to the MMC/SD card when the clock frequency is 0, i.e.
the core has stated that the MCI clock does not need to be generated.
It is inspired by existing clock gating code found in the OMAP and
Atmel drivers and brings this up to the host abstraction. Gating is
performed before and after any MMC request.
This patchset implements this for the MMCI/PL180 MMC/SD host controller,
but it should be simple to switch OMAP/Atmel over to using this instead.
mmc_set_{gated,ungated}() add variable protection to the state holders
for the clock gating code. This is particularly important when ordinary
.set_ios() calls would race with the .set_ios() call resulting from a
delayed gate operation.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
Workqueue creation API has been updated and flush_scheduled_work() is
deprecated and scheduled to be removed.
* core/core.c: Use alloc_ordered_workqueue() instead of
create_singlethread_workqueue(). This removes an unnecessary
rescuer.
* host/omap.c: Create, use and flush mmc_omap_wq instead of the
system_wq.
* Flush host->mmc_carddetect_work directly on removal instead of using
flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Chris Ball <cjb@laptop.org>
Cc: linux-mmc@vger.kernel.org
In the error-path where PM notifies PM_POST_RESTORE, the rescan-blockage
should be cleared as well. Otherwise it'll be never re-probed.
Also, as a bonus, this fixes a bug in S4 with user-mode suspend in the
current code, as it sends PM_POST_RESTORE instead of
PM_POST_HIBERNATION wrongly.
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some board/card/host configurations are not capable of powering off the
card after boot.
To support such configurations, and to allow smoother transition to
runtime PM behavior, MMC_CAP_POWER_OFF_CARD is added, so hosts need to
explicitly indicate whether it's OK to power off their cards after boot.
SDIO core will enable runtime PM for a card only if that cap is set.
As a result, the card will be powered down after boot, and will only
be powered up again when a driver is loaded (and then it's up to the
driver to decide whether power will be kept or not).
This will prevent sdio_bus_probe() failures with setups that do not
support powering off the card.
Reported-and-tested-by: Daniel Drake <dsd@laptop.org>
Reported-and-tested-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Power off the card in mmc_sdio_detect __before__ a potential error
handler, which completely removes the card, executes, and only if the
card was successfully powered on beforehand.
While we're at it, use the _sync variant of the runtime PM put API, in
order to ensure that the card is left powered off in case an error
occurred, and the card is going to be removed.
Reproduced and tested on the OLPC XO-1.5.
Reported-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC hosts that poll for card detection by defining the MMC_CAP_NEEDS_POLL
flag have a race on rmmod, where the delayed work is cancelled without
waiting for completed polling. To prevent this a _sync version of the work
cancellation has to be used.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We should not call mmc_card_set_ddr_mode() if we are in single data
mode. This sets DDR and causes the kernel log to say the card is DDR
when it is not.
Explicitly set ddr to 0 rather then rely on MMC_SDR_MODE being 0 when
doing the checks.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For debugging power management features it is convenient to have the
possibility of changing the MMC host controller clock at runtime. This
patch adds a 'clock' file for this under the MMC host root of debugfs.
Usage is as follows:
# cat /sys/kernel/debug/mmc0/clock
52000000
# echo "1000000000" > /sys/kernel/debug/mmc0/clock
# cat /sys/kernel/debug/mmc0/clock
52000000
# echo "48000000" > /sys/kernel/debug/mmc0/clock
# cat /sys/kernel/debug/mmc0/clock
48000000
The middle example shows limits being applied by the host driver.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
[cjb: modify changelog language]
Signed-off-by: Chris Ball <cjb@laptop.org>
Bring SDIO devices back to full power before their suspend
handler is invoked.
Doing so ensures that SDIO suspend/resume semantics are
maintained (drivers still get to decide whether their
card should be removed or kept during system suspend,
and at what power state), and that SDIO suspend/resume
execution paths are unchanged.
This is achieved by resuming a runtime-suspended SDIO device
in its ->prepare() PM callback (similary to the PCI subsystem).
Since the PM core always increments the run-time usage
counter before calling the ->prepare() callback and decrements
it after calling the ->complete() callback, it is guaranteed
that when the system will come out of suspend, our device's
power state will reflect its runtime PM usage counter.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
To prevent an erroneous removal of the card, make sure
the device is powered when it is mmc_sdio_detect()ed.
This is required since mmc_sdio_detect may be invoked
while the device is runtime suspended (e.g., MMC core
is rescanning when system comes out of suspend).
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enable runtime PM for SDIO functions.
SDIO functions are initialized with a disabled runtime PM state,
and are set active (and their usage count is incremented)
only before potential drivers are probed.
SDIO function drivers that support runtime PM should call
pm_runtime_put_noidle() in their probe routine, and
pm_runtime_get_noresume() in their remove routine (very
similarly to PCI drivers).
In case a matching driver does not support runtime PM, power will
always be kept high (since the usage count is positive).
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enable runtime PM for new SDIO cards.
As soon as the card will be added to the device tree, runtime PM core
will release its power, since it doesn't have any users yet.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Assign the generic runtime PM handlers for SDIO.
These handlers invoke the relevant SDIO function drivers'
handlers, if exist, otherwise they just return success
(so SDIO drivers don't have to define any runtime PM handlers
unless they need to).
Runtime PM is still disabled by default, so this patch alone
has no immediate effect.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add MMC runtime PM handlers, which call mmc_power_save_host
and mmc_power_restore_host in response to runtime_suspend and
runtime_resume events.
Runtime PM is still disabled by default, so this patch alone
has no immediate effect.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a power_restore handler to the SDIO bus ops,
in order to support waking up SDIO cards that
were powered off by runtime pm.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allow power save/restore and their relevant mmc_bus_ops handlers
exit with a return value.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
On resume, let mmc_sdio_init_card go all the way, instead
of skipping the reconfiguration of the card's speed and width.
This is needed to ensure cards wake up with their clock
reconfigured (otherwise it's kept low).
This patch also removes the explicit bus width reconfiguration
on resume, since now this is part of mmc_sdio_init_card.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
One flaw with DDR support is that MMC core does not inform the driver
which DDR mode it has selected. This patch expands the ios->ddr flag
to do that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The DDR support patch needs the following fixes:
- The block driver does not need to know about DDR, any more
than it needs to know about bus width.
- Not only the card must be switched to DDR mode. The host
controller must also be configured, which is done through
the 'set_ios()' function.
- Do not set the DDR mode state until after the switch command
is successful.
- Setting block length is not supported in DDR mode. Make that
a core function and change the other place it is used (mmc_test)
also.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add support for Dual Data Rate MMC cards as defined in the 4.4
specification.
Signed-off-by: Hanumath Prasad <hanumath.prasad@stericsson.com>
Cc: linux-mmc@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Tested-by Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
After discovering a problem in regulator reference counting I took Mark
Brown's advice to move the reference count into the MMC core by making the
regulator status a member of struct mmc_host.
I took this opportunity to also implement NULL versions of
the regulator functions so as to rid the driver code from
some ugly #ifdef CONFIG_REGULATOR clauses.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Sundar Iyer <sundar.iyer@stericsson.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Cliff Brake <cbrake@bec-systems.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_rescan() includes a pr_info which prints 4 lines each second for
hosts configured with MMC_CAP_NEEDS_POLL. This patch enables the message
only if CONFIG_MMC_DEBUG is selected. Tested on i.MX51's sdhci-esdhc.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Hein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the latest releases of the mmc driver, the freq during initialization
is set to a fixed 400 Khz. This was reportedly too fast for several
users. As there doesn't seem to be an ideal frequency
which-works-for-all, Pierre suggested to let the driver try several
frequencies.
This patch implements that idea. It will try mmc-initialization using
several frequencies from an array 400, 300, 200 and 100.
In case SDIO is broken, it'll still try to detect SDMEM, also at different
freqs.
Signed-off-by: Hein Tibosch <hein_tibosch@yahoo.es>
Cc: Pierre Ossman <pierre@ossman.eu>
Reviewed-by: Chris Ball <cjb@laptop.org>
Tested-by: Chris Ball <cjb@laptop.org>
Cc: Ben Nizette <bn@niasdigital.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are two checks that need to be made when determining whether a
card is removable. A host controller may set MMC_CAP_NONREMOVABLE if the
controller does not support removing cards (e.g. eMMC), in which case
the card is physically non-removable. Also the 'mmc_assume_removable'
module parameter can be configured at module load time, in which case
the card may be logically non-removable.
A helper function keeps the logic in one place so that code always
checks both conditions.
Because this new function is likely to be called from modules we now
need to export the mmc_assume_removable symbol.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The EXTRA_CFLAGS assignment in mmc/Makefile was not accomplishing
anything because this flag only has effect on sources at the same level
as the makefile (i.e., per directory). Since card/, core/, and host/
rely on MMC_DEBUG, the subdir-ccflags-y variant seems to be the
appropriate choice.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Global symbols should use their subsystem name in a prefixed fashion.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Conversion from struct device to struct mmc_card is used more than in one
place. Due to this it's better to have public macro for such thing.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We have deprecated the distinction between hardware and physical
segments in the block layer. Consolidate the two limits into one in
drivers/mmc/.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
Fix SDIO suspend/resume regression introduced by 4c2ef25fe0 "mmc: fix
all hangs related to mmc/sd card insert/removal during suspend/resume":
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
pm_op(): platform_pm_suspend+0x0/0x5c returns -38
PM: Device pxa2xx-mci.0 failed to suspend: error -38
PM: Some devices failed to suspend
4c2ef25fe0 moved the card removal/insertion mechanism out of MMC's
suspend/resume path and into pm notifiers (mmc_pm_notify), and that
broke SDIO's expectation that mmc_suspend_host() will remove the card,
and squash the error, in case -ENOSYS is returned from the bus suspend
handler (mmc_sdio_suspend() in this case).
mmc_sdio_suspend() is using this whenever at least one of the card's SDIO
function drivers does not have suspend/resume handlers - in that case
it is agreed to force removal of the entire card.
This patch fixes this regression by trivially bringing back that part of
mmc_suspend_host(), which was removed by 4c2ef25fe0.
Reported-and-tested-by: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: <stable@kernel.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
The introduction of support for SD combo cards breaks the initialization
of all CSR SDIO chips. The GO_IDLE (CMD0) in mmc_sd_get_cid() causes CSR
chips to be reset (this is non-standard behavior).
When initializing an SDIO card check for a combo card by using the memory
present bit in the R4 response to IO_SEND_OP_COND (CMD5). This avoids the
call to mmc_sd_get_cid() on an SDIO-only card.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Acked-by: Michal Mirolaw <mirq-linux@rere.qmqm.pl>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a build breakage introduced by commit 4c2ef25fe0 ("mmc: fix
all hangs related to mmc/sd card insert/removal during suspend/resume")
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-mmc@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are some chips (like TI WL12xx series) that can be interfaced over
SDIO but don't support the SDIO specification, meaning that they are
missing CIA (Common I/O Area) with all it's registers. Current Linux SDIO
implementation relies on those registers to identify and configure the
card, so non-standard cards can not function and cause lots of warnings
from the core when it reads invalid data from non-existent registers.
After this patch, init_card() host callback can now set new quirk
MMC_QUIRK_NONSTD_SDIO, which means that SDIO core should not try to access
any standard SDIO registers and rely on init_card() to fill all SDIO
structures instead. As those cards are usually embedded chips, all the
required information can be obtained from machine board files by the host
driver when it's called through init_card() callback.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Kalle Valo <kvalo@adurom.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A non-zero value of SEC_COUNT does not indicate that the card is sector
addressed. According to the MMC specification, cards with a density
greater than 2GiB are sector addressed.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Hanumath Prasad <hanumath.prasad@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If you don't use CONFIG_MMC_UNSAFE_RESUME, as soon as you attempt to
suspend, the card will be removed, therefore this patch doesn't change the
behavior of this option.
However the removal will be done by pm notifier, which runs while
userspace is still not frozen and thus can freely use del_gendisk, without
the risk of deadlock which would happen otherwise.
Card detect workqueue is now disabled while userspace is frozen, Therefore
if you do use CONFIG_MMC_UNSAFE_RESUME, and remove the card during
suspend, the removal will be detected as soon as userspace is unfrozen,
again at the moment it is safe to call del_gendisk.
Tested with and without CONFIG_MMC_UNSAFE_RESUME with suspend and hibernate.
[akpm@linux-foundation.org: clean up function prototype]
[akpm@linux-foundation.org: fix CONFIG_PM-n linkage, small cleanups]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This series adds support for SD combo cards to MMC/SD driver stack.
SD combo consists of SD memory and SDIO parts in one package. Since the
parts have a separate SD command sets, after initialization, they can be
treated as independent cards on one bus.
Changes are divided into two patches. First is just moving initialization
code around so that SD memory part init can be called from SDIO init.
Second patch is a proper change enabling SD memory along SDIO. I tried to
move as much no-op changes to the first patch so that it's easier to
follow the required changes to initialization flow for SDIO cards.
This is based on Simplified SDIO spec v.2.00. The init sequence is
slightly modified to follow current SD memory init implementation.
Command sequences, assuming SD memory and SDIO indeed ignore unknown
commands, are the same as before for both parts.
This patch:
Prepare for SD-combo (IO+mem) support by splitting SD memory
card init and related functions.
Signed-off-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The eMMC spec 4.4 and 4.3 + additional feature chips has CSD structure
version 3 and version 3 have to check the CSD_STRUCTURE byte in the
EXT_CSD register.
Also fix EXT_CSD revision message.
[akpm@linux-foundation.org: fix comment, per Chris Ball]
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SDIO specification allows RAW (Read after Write) operation using
IO_RW_DIRECT command (CMD52) by setting the RAW bit. This operation is
similar to ordinary read/write commands, except that both write and read
are performed using single command/response pair. The Linux SDIO layer
already supports this internaly, only external function is missing for
drivers to make use, which is added by this patch.
This type of command is required to implement proper power save mode
support in wl1251 wifi driver.
Android has similar patch for G1 in it's tree for the same reason:
http://android.git.kernel.org/?p=kernel/common.git;a=commitdiff;h=74a47786f6ecbe6c1cf9fb15efe6a968451deb52
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Cc: Dmitry Shmidt <dimitrysh@google.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Even though many mmc host drivers pass a pm_message_t argument to
mmc_suspend_host() that argument isn't used the by MMC core. As host
drivers are converted to dev_pm_ops they'll have to construct
pm_message_t's (as they won't be passed by the PM subsystem any more) just
to appease the mmc suspend interface.
We might as well just delete the unused paramter.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>ZZ
Acked-by: Sascha Sommer <saschasommer@freenet.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The clearing of mrq via a memset at the top of the for loop in
mmc_wait_for_app_cmd() is not required as mrq is not used and there is
another clearing of mrq just below. We remove the first memset since if
the initial tests in the for loop fail the memset is not required.
Signed-off-by: Mark Asselstine <asselsm@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MX3 SoCs have a silicon bug which corrupts CRC calculation of
multi-block transfers when connected SDIO peripheral doesn't drive the
BUSY line as required by the specs.
One way to prevent this is to only allow 1-bit transfers.
Another way is playing tricks with the DMA engine, but this isn't
mainline yet. So for now, we live with the performance drawback of 1-bit
transfers until a nicer solution is found.
This patch introduces a new host controller callback 'init_card' which
is for now only called from mmc_sdio_init_card().
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Volker Ernst <volker.ernst@txtr.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Michał Mirosław <mirqus@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
In the extended CSD register the CARD_TYPE is an 8-bit value of which the
upper 6 bits were reserved in JEDEC specifications prior to version 4.4.
In version 4.4 two of the reserved bits were designated for identifying
support for the newly added High-Speed Dual Data Rate. Unfortunately the
mmc_read_ext_csd() function required that the reserved bits be zero
instead of ignoring them as it should.
This patch makes mmc_read_ext_csd() ignore the CARD_TYPE bits that are
reserved or not yet supported. It also stops the function jumping to the
end as though an error occurred, when it is only warns that the CARD_TYPE
bits (that it does interpret) are invalid.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SDIO Simplified Specification V2.00 states that it is strongly recommended
that the host executes either a power reset or issues a CMD52 (I/O Reset)
to re-initialize an I/O only card or the I/O portion of a combo card.
Additionally, the CMD52 must be issued first because it cannot be issued
after a CMD0.
With this patch the Nintendo Wii SDIO-based WLAN card is detected after a
system reset, without requiring a complete system powercycle.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
And bring them back to 4-bit mode during resume.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some SDIO cards may suspend while keeping function interrupts active
especially in the powered suspend case. Upon resume we need to kick the
SDIO interrupt thread to check for pending interrupts and to restart card
IRQ detection at the host controller level.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Seen on a Marvell 8686 SDIO card and Via VX855 controller: we must avoid
sending CMD3/5/7 on a resume where power has been maintained, because the
8686 will refuse to respond to them and the MMC stack will give up on the
card.
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series provides the core changes needed to allow SDIO cards to
remain powered and active while the host system is suspended, and let them
wake up the host system when needed. This is used to implement
wake-on-lan with SDIO wireless cards at the moment. Patches to add that
support to the libertas driver will be posted separately.
This patch:
Some SDIO cards have the ability to keep on running autonomously when the
host system is suspended, and wake it up when needed. This however
requires that the host controller preserve power to the card, and
configure itself appropriately for wake-up.
There is however 4 layers of abstractions involved: the host controller
driver, the MMC core code, the SDIO card management code, and the actual
SDIO function driver. To make things simple and manageable, host drivers
must advertise their PM capabilities with a feature bitmask, then function
drivers can query and set those features from their suspend method. Then
each layer in the suspend call chain is expected to act upon those bits
accordingly.
[akpm@linux-foundation.org: fix typo in comment]
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some SDIO cards expect byte transfers not to exceed the configured block
transfer size. Add a quirk to that effect.
Patches to make use of this quirk will be sent separately.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Drake noticed a crash in the error path of mmc_attach_sdio(). This
bug is discussed at http://dev.laptop.org/ticket/9707.
BUG: unable to handle kernel paging request at 6b6b6c57
IP: [<b066d6e2>] sdio_remove_func+0x9/0x27
Call Trace:
[<b066cfb4>] ? mmc_sdio_remove+0x34/0x65
[<b066d1fc>] ? mmc_attach_sdio+0x217/0x240
[<b066a22f>] ? mmc_rescan+0x1a2/0x20f
[<b042e9a0>] ? worker_thread+0x156/0x1e
We need to accurately track how many SDIO functions have been initialised
(and keep card->sdio_funcs in sync) so that we don't try to remove more
functions than we initialised if we hit the error path in
mmc_attach_sdio().
Without this patch if we hit the error path in mmc_attach_sdio() we run
the risk of deferencing invalid memory in sdio_remove_func(), leading to a
crash.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Cc: Daniel Drake <dsd@laptop.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sdio_remove_func() needs to be more careful about reference counting. It
can be called in error paths where sdio_add_func() has never been called
e.g. mmc_attach_sdio error path --> mmc_sdio_remove --> sdio_remove_func
Signed-off-by: Daniel Drake <dsd@laptop.org>
Reviewed-by: Matt Fleming <matt@console-pimps.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some people run general-purpose distribution kernels on netbooks with
a card that is physically non-removable or logically non-removable
(e.g. used for /home) and cannot be cleanly unmounted during suspend.
Add a module parameter to set whether cards are assumed removable or
non-removable, with the default set by CONFIG_MMC_UNSAFE_RESUME.
In general, it is not possible to tell whether a card present in an MMC
slot after resume is the same that was there before suspend. So there are
two possible behaviours, each of which will cause data loss in some cases:
CONFIG_MMC_UNSAFE_RESUME=n (default): Cards are assumed to be removed
during suspend. Any filesystem on them must be unmounted before suspend;
otherwise, buffered writes will be lost.
CONFIG_MMC_UNSAFE_RESUME=y: Cards are assumed to remain present during
suspend. They must not be swapped during suspend; otherwise, buffered
writes will be flushed to the wrong card.
Currently the choice is made at compile time and this allows that to be
overridden at module load time.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Wouter van Heyst <larstiq@larstiq.dyndns.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rework the current CIS tuple parsing code, reusing the existing
infrastructure and providing an easy way to add new CISTPL_FUNCE parsers
by TPLFE_TYPE.
Valid known CIS tuples are now silently queued for the SDIO function
driver when not parsed/processed (-EILSEQ) by the SDIO core. Unknown CIS
tuples (-ENOENT) are queued too for the SDIO function driver without
aborting the initialization, but emit a warning in the kernel log.
CISTPL_FUNCE tuples can be "whitelisted" now by adding a matching entry to
the cis_tpl_funce_list table.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Pierre Ossman <pierre@ossman.eu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PC Card 8.0 specification (vol. 4, section 3.2.10) says the
TPLLV1_INFO field of the CISTPL_VERS_1 tuple must contain 4 strings. Some
cards don't have all 4 so just parse as many as we can.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Tested-by: Jonathan Cameron <jic23@cam.ac.uk>
Tested-by: Bing Zhao <bzhao@marvell.com>
Cc: Roel Kluin <roel.kluin@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some manufacturers provide vendor information in non-vendor specific CIS
tuples. For example, Broadcom uses an Extended Function tuple to provide
the MAC address on some of their network cards, as in the case of the
Nintendo Wii WLAN daughter card.
This patch allows passing whitelisted FUNCE tuples unknown to the SDIO
core to a matching SDIO driver instead of rejecting them and failing.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Especially with the PM framework, those are quite handy to have in driver
code too.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Especially for SDIO drivers which may have special conditions/errors to
report, it is a good thing to relay the returned error code back to upper
layers.
This also allows for the rationalization of the resume path where code to
"remove" a no-longer-existing or replaced card was duplicated into the
MMC, SD and SDIO bus drivers.
In the SDIO case, if a function suspend method returns an error, then all
previously suspended functions are resumed and the error returned. An
exception is made for -ENOSYS which the core interprets as "we don't
support suspend so just kick the card out for suspend and return success".
When resuming SDIO cards, the core code only validates the manufacturer
and product IDs to make sure the same kind of card is still present before
invoking functions resume methods. It's the function driver's
responsibility to perform further tests to confirm that the actual same
card is present (same MAC address, etc.) and return an error otherwise.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, all SDIO cards are virtually removed upon a suspend, and
completely reprobed upon a resume. This adds the suspend and resume
methods to the SDIO bus driver so to be able to dispatch those events to
the actual SDIO function drivers for real suspend/resume instead.
All active functions on a card must have a driver with both a suspend and
a resume method though. Failing that, we fall back to the current
behavior of simply "removing" the card when suspending.
When resuming, we make sure the same card is still inserted by comparing
the vendor and product IDs. If there is a mismatch, or if there is simply
no card anymore in the slot, then the previous card is "removed" and the
new card is detected. This is further enhanced with the next patch.
[akpm@linux-foundation.org: fix warnings]
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some time ago, I have send a patch to the mmc_spi subsystem changing the
error codes. This was after a discussion with Pierre about using EINVAL
only for non-recoverable errors. This patch was accepted as
http://git.kernel.org/linus/fdd858db7113ca64132de390188d7ca00701013d
Unfortunately, several weeks later, I realized that this patch has opened
a little can of worms because there are SD cards on the market which
a) claim that they support the switch command
AND
b) refuse to execute this command if operating in SPI mode.
So, such a card would get unusuable in an embedded linux system in SPI
mode, because the init sequence terminates with an error.
This patch adds the missing error codes to the caller of the switch
command and restores the old behaviour to fail gracefully if these
commands can not execute.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org> [2.6.31.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Normally writes to SDIO function 0 outside the vendor specific CCCR
registers are prohibited.
To support embedded devices that require writes to SDIO function 0 outside
this range (e.g. TI WL127x embedded sdio wifi device),
MMC_QUIRK_LENIENT_FN0 is introduced.
A card quirks field is added to `struct mmc_card' to support non-standard
devices (e.g. embedded sdio devices).
[akpm@linux-foundation.org: code in C, not cpp!]
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support to disconnect the pull-up resistor on CD/DAT[3] (pin 1)
of the card. This may be desired on certain setups of boards,
controllers and embedded sdio devices which do not need the card's
pull-up. As a result, card detection is disabled and power is saved.
[akpm@linux-foundation.org: simplify sdio_disable_cd() a bit]
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Philip Langdale <philipl@overt.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to the standard, the SWITCH command should be followed by a
SEND_STATUS command to check for errors.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the new MMC command SLEEP_AWAKE.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Power can be saved by powering off cards that are not in use. This is
similar to suspend / resume except it is under the control of the driver,
and does not require any power management support. It can only be used
when the driver can monitor whether the card is removed, otherwise it is
unsafe. This is possible because, unlike suspend, the driver still
receives card detect and / or cover switch interrupts.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
eMMC's are not removable, so unsafe resume is OK always.
To permit this a new host capability MMC_CAP_NONREMOVABLE has been added
and suspend / resume updated accordingly.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This change allows the MMC host to be claimed in situations where the host
may or may not have already been claimed. Also 'mmc_try_claim_host()' is
now exported.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MMC hosts that support power saving can use the 'enable' and 'disable'
methods to exit and enter power saving states. An explanation of their
use is provided in the comments added to include/linux/mmc/host.h.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is needed for 1.8V embedded SDIO devices and supporting host controllers
(e.g. TI 127x and ZOOM2 boards)
Signed-off-by: Ohad Ben-Cohen <ohad@bencohen.org>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Philip Langdale <philipl@overt.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When mmc_power_up is called during unsafe resume, host->ocr should be used
instead of host->ocr_avail.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Philip Langdale <philipl@overt.org>
Acked-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let attribute group vectors be declared "const". We'd
like to let most attribute metadata live in read-only
sections... this is a start.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some controllers allow a much lower frequency than 400kHz.
Keep the minimum frequency within sensible limits.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With this patch, mmc_rescan can detect the removal of an mmc card and
the insertion of (possibly another) card in the same run. This means
that a card change can be detected without having to call
mmc_detect_change multiple times.
This change generalises the core such that it can be easily used by
hosts which provide a mechanism to detect only the presence of a card
reader cover, which has to be taken off in order to insert a card. Other
hosts ("card detect" or "MMC_CAP_NEEDS_POLL") each receive an event when
a card is removed and when a card is inserted, so it is sufficient for
them if mmc_rescan handles only one event at a time. "Cover detect"
hosts, however, only receive events about the cover status. This means
that between 2 subsequent events, both a card removal and a card
insertion can occur. In this case, the pre-patch version of mmc_rescan
would only detect the removal of the previous card but not the insertion
of the new card.
Signed-off-by: Jorg Schummer <ext-jorg.2.schummer@nokia.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The TI controller on Toshiba Tecra M5 needs more time to power up or
the cards will init incorrectly or not at all.
Signed-off-by: José M. Fernández <josemariafg@gmail.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Some cards are not able to calculate a valid CRC16 value
for CID and CSD reads (CRC for 512 byte data blocks is OK).
By moving the CRC enable after the read of CID and CSD, these
cards can be used. This patch was tested with a faulty 8 GByte
takeMS Class 6 SDHC card. This patch was suggested by
Pierre Ossman.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (42 commits)
atmel-mci: fix sdc_reg typo
tmio_mmc: add maintainer
mmc: Add OpenFirmware bindings for SDHCI driver
sdhci: Add quirk for forcing maximum block size to 2048 bytes
sdhci: Add quirk for controllers that need IRQ re-init after reset
sdhci: Add quirk for controllers that need small delays for PIO
sdhci: Add set_clock callback and a quirk for nonstandard clocks
sdhci: Add get_{max,timeout}_clock callbacks
sdhci: Add support for hosts reporting inverted write-protect state
sdhci: Add support for card-detection polling
sdhci: Enable only relevant (DMA/PIO) interrupts during transfers
sdhci: Split card-detection IRQs management from sdhci_init()
sdhci: Add support for bus-specific IO memory accessors
mmc_spi: adjust for delayed data token response
omap_hsmmc: Wait for SDBP
omap_hsmmc: Fix MMC3 dma
omap_hsmmc: Disable SDBP at suspend
omap_hsmmc: Do not prefix slot name
omap_hsmmc: Allow cover switch to cause rescan
omap_hsmmc: Add 8-bit bus width mode support
...
Glue between MMC and regulator stacks ... verified with
some OMAP3 boards using adjustable and configured-as-fixed
regulators on several MMC controllers.
These calls are intended to be used by MMC host adapters
using at least one regulator per host. Examples include
slots with regulators supporting multiple voltages and
ones using multiple voltage rails (e.g. DAT4..DAT7 using a
separate supply, or a split rail chip like certain SDIO
WLAN or eMMC solutions).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some SD cards have very high timeouts in SPI mode.
So adjust the timeouts from theory to practice.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
During mmc unsafe resume, choose the right voltage for the card after
powerup.
Although this has not seen to cause trouble, it's the wrong behaviour.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Extended CSD is a MMC card register. As increasingly interesting
fields are being added to Extended CSD, it is helpful to see its
value. Note that SD cards do not have an Extended CSD
register, so it is MMC only.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Currently we are using an explicit udev rule to trigger loading of the
mmc-block module when an MMC or SD card is detected:
SUBSYSTEM=="mmc", RUN+="/sbin/modprobe -Qba mmc-block"
It makes much more sense for the mmc bus driver and the mmc-block module to
share MODALIAS information so that they are linked automatically.
There is no real information of use in the MMC system at the current time.
All devices inserted require us to load the mmc-block device. Until such
time as useful parameters exist simply reflect the module linkage via
the module alias below:
mmc:block
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The delayed work item mmc_host.detect is now cancelled before flushing
the work queue. This takes care of cases when delayed_work was scheduled
for mmc_host.detect, but not yet placed in the work queue.
Signed-off-by: Jorg Schummer <ext-jorg.2.schummer@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Commit 0d3e0460f3
"MMC: CSD and CID timeout values" inadvertently broke
the timeout for the MMC command SEND_EXT_CSD.
This patch puts it back again.
Depending on the characteristics of the controller,
this bug may prevent the use of MMC cards.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Get rid of a silent failure mode when the MMC/SD host doesn't
support the voltages needed to operate a given card, by
adding a warning. A 3.3V host and a 3.0V card, for example,
no longer need to mysteriously just not work at all.
This isn't the best diagnostic; ideally it would also tell
what voltage the card and host support (and not just by
dumping the bitmasks).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This function sets the OCR mask bits according to provided voltage
ranges. Will be used by the mmc_spi OpenFirmware bindings.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
It seems that some cards are slightly out of spec and occasionally
will not be able to complete a write in the alloted 250 ms [1].
Incease the timeout slightly to allow even these cards to function
properly.
[1] http://lkml.org/lkml/2008/9/23/390
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The MMC spec states that the timeout for accessing the CSD and CID
registers is 64 clock cycles.
Signed-off-by: Matthew Fleming <matthew.fleming@imgtec.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Make sure we can be woken from the forced sleep that is done on errors.
Removing a card often results in -ENOMEDIUM or -EILSEQ so we previously
locked up the removal process for a second.
We could completely exit on -ENOMEDIUM, but it might be a transient
glitch so treat it like any other error.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
For each card successfully added to the bus, create a subdirectory under
the host's debugfs root with information about the card.
At the moment, only a single file is added to the card directory for
all cards: "state". It reflects the "state" field in struct mmc_card,
indicating whether the card is present, readonly, etc.
For MMC and SD cards (not SDIO), another file is added: "status".
Reading this file will ask the card about its current status and
return it. This can be useful if the card just refuses to respond to
any commands, which might indicate that the card state is not what the
MMC core thinks it is (due to a missing stop command, for example.)
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
When CONFIG_DEBUG_FS is set, create a few files under /sys/kernel/debug
containing information about an mmc host's internal state. Currently,
just a single file is created, "ios", which contains information about
the current operating parameters for the bus (clock speed, bus width,
etc.)
Host drivers can add additional files and directories under the host's
root directory by passing the debugfs_root field in struct mmc_host as
the 'parent' parameter to debugfs_create_*.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Unfold nested macros it creates not readable code and
sparse warnings
sdio_io.c:190:9: warning: symbol '_min1' shadows an earlier one
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This adds reading and using of enable_timeout from the CIS
Signed-off-by: Benzi Zbit <benzi.zbit@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch fixes sdio_io sparse errors.
This fix changes signature of API functions,
changing
unsigned char -> u8
unsigned short -> u16
unsigned long -> u32 - this was probably a bug in 64 bit platforms
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Make sure that the maximum size for a byte mode transfer is identical
in all places. Also tweak the transfer helper so that a single byte
mode transfer is preferred over (possibly multiple) block mode
request(s).
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
There are a lot of crappy controllers out there that cannot handle
all the request sizes that the MMC/SD/SDIO specifications require.
In case the card driver can pad the data to overcome the problems,
this commit adds a helper that calculates how much that padding
should be.
A corresponding helper is also added for SDIO, but it can also deal
with all the complexities of splitting up a large transfer efficiently.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Make the variable name in the comments match the actual name
of the variable.
Signed-off-by: Deepak Saxena <dsaxena@laptop.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Now get_ro() callback must return 0/1 values for its logical states, and
negative errno values in case of error. If particular host instance doesn't
support RO/WP switch, it should return -ENOSYS.
This patch changes some hosts in two ways:
1. Now functions should be smart to not return negative values in
"RO asserted" case (particularly gpio_ calls could return negative
values for the outermost GPIOs).
Also, board code usually passes get_ro() callbacks that directly return
gpioreg & bit result, so at91_mci, imxmmc, pxamci and mmc_spi's get_ro()
handlers need take special care when returning platform's values to the
mmc core.
2. In case of host instance didn't implement get_ro() callback, it should
really return -ENOSYS and let the mmc core decide what to do about it
(mmc core thinks the same way as the hosts, so it isn't functional
change).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some hosts (and boards that use mmc_spi) do not use interrupts on the CD
line, so they can't trigger mmc_detect_change. We want to poll the card
and see if there was a change. 1 second poll interval seems resonable.
This patch also implements .get_cd() host operation, that could be used
by the hosts that are able to report card-detect status without need to
talk MMC.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Every file should include the headers containing the externs for its
global functions.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds proper prototypes for mmc_attach_*() in
drivers/mmc/core/core.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch makes the needlessly global __mmc_release_bus() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Reorganise code so that mmc_hostname() works directly after allocation.
That way host drivers can use that name for resource allocations and
messages during probing.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Suppressing uevents turned out to be a bad idea as it screws up the
order of events, making user space very confused. Change the system to
use sysfs groups instead.
This is a regression that, for some odd reason, has gone unnoticed for
some time. It confuses hal so that the block devices (which have the
mmc device as a parent) are not registered. End result being that
desktop magic when cards are inserted won't work.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not architecture specific code should not #include <asm/scatterlist.h>.
This patch therefore either replaces them with
#include <linux/scatterlist.h> or simply removes them if they were
unused.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
MMC over SPI sends the CID and CSD registers as data, not responses,
which means that the host driver won't do the necessary byte flipping
for us.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The exception path associated with an invalid ext_csd_struct returns
without freeing ext_csd.
Coverity CID 1909.
Signed-off-by: Florin Malita
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (75 commits)
PM: merge device power-management source files
sysfs: add copyrights
kobject: update the copyrights
kset: add some kerneldoc to help describe what these strange things are
Driver core: rename ktype_edd and ktype_efivar
Driver core: rename ktype_driver
Driver core: rename ktype_device
Driver core: rename ktype_class
driver core: remove subsystem_init()
sysfs: move sysfs file poll implementation to sysfs_open_dirent
sysfs: implement sysfs_open_dirent
sysfs: move sysfs_dirent->s_children into sysfs_dirent->s_dir
sysfs: make sysfs_root a regular directory dirent
sysfs: open code sysfs_attach_dentry()
sysfs: make s_elem an anonymous union
sysfs: make bin attr open get active reference of parent too
sysfs: kill unnecessary NULL pointer check in sysfs_release()
sysfs: kill unnecessary sysfs_get() in open paths
sysfs: reposition sysfs_dirent->s_mode.
sysfs: kill sysfs_update_file()
...
This changes the uevent buffer functions to use a struct instead of a
long list of parameters. It does no longer require the caller to do the
proper buffer termination and size accounting, which is currently wrong
in some places. It fixes a known bug where parts of the uevent
environment are overwritten because of wrong index calculations.
Many thanks to Mathieu Desnoyers for finding bugs and improving the
error handling.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We register a simple trigger so make sure we use the corresponding
unregister function.
(Also means we get a dummy function when triggers aren't compiled in)
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Currently we print a message about some bad states wrt function IRQ
handlers but return 0 from process_sdio_pending_irqs() nevertheless.
This can lead to an infinite loop as nothing might have cleared the
condition for the pending card interrupt from the host controller by
the time host->ops->enable_sdio_irq(host, 1) is called.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
If func is actually null we won't get much from sdio_func_id(func).
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The interrupt polling frequency is a compromise between power usage and
interrupt latency. Unfortunately, it affects throughput rather severely
for devices which require an interrupt for every chunk of data.
By making the polling frequency adaptive, we get better throughput with
those devices without sacficing too much power. Polling will quickly
increase when there is an actual interrupt, and slowly fall back to the
idle frequency when the interrupts stop coming.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add a led trigger for each host controller that indicates if there
is a request active on the controller.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Teach the MMC/SD/SDIO core about using SPI mode.
- Use mmc_host_is_spi() so enumeration works through SPI signaling
and protocols, not just the native versions.
- Provide the SPI response type flags with each request issued,
including requests from the new lock/unlock code.
- Understand that cmd->resp[0] and mmc_get_status() results for SPI
return different values than for "native" MMC/SD protocol; this
affects resetting, checking card lock status, and some others.
- Understand that some commands act a bit differently ... notably:
* OP_COND command doesn't return the OCR
* APP_CMD status doesn't have an R1_APP_CMD analogue
Those changes required some new and updated primitives:
- Provide utilities to access two SPI-only requests, and one
request that wasn't previously needed:
* mmc_spi_read_ocr() ... SPI only
* mmc_spi_set_crc() ... SPI only (override by module parm)
* mmc_send_cid() ... for use without broadcast mode
- Updated internal routines:
* Previous mmc_send_csd() modified into mmc_send_cxd_native();
it uses native "R2" responses, which include 16 bytes of data.
* Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data()
helper for command-and-data access
* Bugfix to that mmc_send_cxd_data() code: dma-to-stack is
unsafe/nonportable, so kmalloc a bounce buffer instead.
- Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper
- Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use
those helper routines based on whether they're native or SPI
The newest categories of cards supported by the MMC stack aren't expected
to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO.
All those cards support SPI mode, so eventually they should work too.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Increase delay for power up in order to support some slower boards.
Also add some comments about why the delays are there.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add sdio_f0_readb() and sdio_f0_writeb() functions to reading and
writing function 0 registers. Writes outside the vendor specific CCCR
registers (0xF0 - 0xFF) are not permitted.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Replace all cases of BUG_ON with WARN_ON where there is a chance
(with varying degrees of slim) that the kernel can continue without
incidence.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Ulf Hansson