The NCSI channel has been configured to provide service if its link
monitor timer is enabled, regardless of its state (inactive or active).
So the timeout event on the link monitor indicates the out-of-service
on that channel, for which a failover is needed.
This sets NCSI_DEV_RESHUFFLE flag to enforce failover on link monitor
timeout, regardless the channel's original state (inactive or active).
Also, the link is put into "down" state to give the failing channel
lowest priority when selecting for the active channel. The state of
failing channel should be set to active in order for deinitialization
and failover to be done.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there are no NCSI channels probed, HWA (Hardware Arbitration)
mode is enabled. It's not correct because HWA depends on the fact:
NCSI channels exist and all of them support HWA mode. This disables
HWA when no channels are probed.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ncsi_channel_monitor() misses stopping the channel monitor in several
places that it should, causing a WARN_ON_ONCE() to trigger when the
monitor is re-started later, eg:
[ 459.040000] WARNING: CPU: 0 PID: 1093 at net/ncsi/ncsi-manage.c:269 ncsi_start_channel_monitor+0x7c/0x90
[ 459.040000] CPU: 0 PID: 1093 Comm: kworker/0:3 Not tainted 4.10.17-gaca2fdd #140
[ 459.040000] Hardware name: ASpeed SoC
[ 459.040000] Workqueue: events ncsi_dev_work
[ 459.040000] [<80010094>] (unwind_backtrace) from [<8000d950>] (show_stack+0x20/0x24)
[ 459.040000] [<8000d950>] (show_stack) from [<801dbf70>] (dump_stack+0x20/0x28)
[ 459.040000] [<801dbf70>] (dump_stack) from [<80018d7c>] (__warn+0xe0/0x108)
[ 459.040000] [<80018d7c>] (__warn) from [<80018e70>] (warn_slowpath_null+0x30/0x38)
[ 459.040000] [<80018e70>] (warn_slowpath_null) from [<803f6a08>] (ncsi_start_channel_monitor+0x7c/0x90)
[ 459.040000] [<803f6a08>] (ncsi_start_channel_monitor) from [<803f7664>] (ncsi_configure_channel+0xdc/0x5fc)
[ 459.040000] [<803f7664>] (ncsi_configure_channel) from [<803f8160>] (ncsi_dev_work+0xac/0x474)
[ 459.040000] [<803f8160>] (ncsi_dev_work) from [<8002d244>] (process_one_work+0x1e0/0x450)
[ 459.040000] [<8002d244>] (process_one_work) from [<8002d510>] (worker_thread+0x5c/0x570)
[ 459.040000] [<8002d510>] (worker_thread) from [<80033614>] (kthread+0x124/0x164)
[ 459.040000] [<80033614>] (kthread) from [<8000a5e8>] (ret_from_fork+0x14/0x2c)
This also updates the monitor instead of just returning if
ncsi_xmit_cmd() fails to send the get-link-status command so that the
monitor properly times out.
Fixes: e6f44ed6d0 "net/ncsi: Package and channel management"
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the value of the HNCDSC AEN packet.
Fixes: 7a82ecf4cf "net/ncsi: NCSI AEN packet handler"
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzkaller got crashes in packet_getsockopt() processing
PACKET_ROLLOVER_STATS command while another thread was managing
to change po->rollover
Using RCU will fix this bug. We might later add proper RCU annotations
for sparse sake.
In v2: I replaced kfree(rollover) in fanout_add() to kfree_rcu()
variant, as spotted by John.
Fixes: a9b6391814 ("packet: rollover statistics")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: John Sperbeck <jsperbeck@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ARM fixes from Russell King:
"Three fixes this time around:
- ensure sparse realises that we're building for a 32-bit arch on
64-bit hosts.
- use the correct instruction for semihosting on v7m (nommu) CPUs.
- reserve address 0 to prevent the first page of memory being used on
nommu systems"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8704/1: semihosting: use proper instruction on v7m processors
ARM: 8701/1: fix sparse flags for build on 64bit machines
ARM: 8700/1: nommu: always reserve address 0 away
Here is another set of bugfixes for ARM SoCs, mostly harmless:
- A boot regression fix on ux500
- PCIe interrupts on NXP i.MX7 and on Marvell Armada 7K/8K were
wired up wrong, in different ways
- Armada XP support for large memory never worked
- The socfpga reset controller now builds on 64-bit
- minor device tree corrections on gemini, mvebu, r-pi 3,
rockchip and at91
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=M8dW
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here is another set of bugfixes for ARM SoCs, mostly harmless:
- a boot regression fix on ux500
- PCIe interrupts on NXP i.MX7 and on Marvell Armada 7K/8K were wired
up wrong, in different ways
- Armada XP support for large memory never worked
- the socfpga reset controller now builds on 64-bit
- minor device tree corrections on gemini, mvebu, r-pi 3, rockchip
and at91"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: ux500: Fix regression while init PM domains
ARM: dts: fix PCLK name on Gemini and MOXA ART
arm64: dts: rockchip: fix typo in iommu nodes
arm64: dts: rockchip: correct vqmmc voltage for rk3399 platforms
ARM: dts: imx7d: Invert legacy PCI irq mapping
bus: mbus: fix window size calculation for 4GB windows
ARM: dts: at91: sama5d2: add ADC hw trigger edge type
ARM: dts: at91: sama5d2_xplained: enable ADTRG pin
ARM: dts: at91: at91-sama5d27_som1: fix PHY ID
ARM: dts: bcm283x: Fix console path on RPi3
reset: socfpga: fix for 64-bit compilation
ARM: dts: Fix I2C repeated start issue on Armada-38x
arm64: dts: marvell: fix interrupt-map property for Armada CP110 PCIe controller
arm64: dts: salvator-common: add 12V regulator to backlight
ARM: dts: sun6i: Fix endpoint IDs in second display pipeline
arm64: allwinner: a64: pine64: Use dcdc1 regulator for mmc0
Two fixes, one for the A31 DRM binding, and one for a missing regulator on
the pine MMC controller.
-----BEGIN PGP SIGNATURE-----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=Cvge
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Pull "Allwinner fixes for 4.14" from Maxime Ripard:
Two fixes, one for the A31 DRM binding, and one for a missing regulator on
the pine MMC controller.
* tag 'sunxi-fixes-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun6i: Fix endpoint IDs in second display pipeline
arm64: allwinner: a64: pine64: Use dcdc1 regulator for mmc0
As pointed out by Linus and David, the earlier waitid() fix resulted in
a (currently harmless) unbalanced user_access_end() call. This fixes it
to just directly return EFAULT on access_ok() failure.
Fixes: 96ca579a1e ("waitid(): Add missing access_ok() checks")
Acked-by: David Daney <david.daney@cavium.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
John Fastabend says:
====================
sockmap fixes for net
The following implements a set of fixes for sockmap and changes the
API slightly in a few places to reduce preempt_disable/enable scope.
We do this here in net because it requires an API change and this
avoids getting stuck with legacy API going forward.
The short description:
Access to skb mark is removed, it is problematic when we add
features in the future because mark is a union and used by the
TCP/socket code internally. We don't want to expose this to the
BPF programs or let programs change the values.
The other change is caching metadata in the skb itself between
when the BPF program returns a redirect code and the core code
implements the redirect. This avoids having per cpu metadata.
Finally, tighten restriction on using sockmap to CAP_NET_ADMIN and
only SOCK_STREAM sockets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Devmap is used with XDP which requires CAP_NET_ADMIN so lets also
make CAP_NET_ADMIN required to use the map.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restrict sockmap to CAP_NET_ADMIN.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb->mark field is a union with reserved_tailroom which is used
in the TCP code paths from stream memory allocation. Allowing SK_SKB
programs to set this field creates a conflict with future code
optimizations, such as "gifting" the skb to the egress path instead
of creating a new skb and doing a memcpy.
Because we do not have a released version of SK_SKB yet lets just
remove it for now. A more appropriate scratch pad to use at the
socket layer is dev_scratch, but lets add that in future kernels
when needed.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
SK_SKB BPF programs are run from the socket/tcp context but early in
the stack before much of the TCP metadata is needed in tcp_skb_cb. So
we can use some unused fields to place BPF metadata needed for SK_SKB
programs when implementing the redirect function.
This allows us to drop the preempt disable logic. It does however
require an API change so sk_redirect_map() has been updated to
additionally provide ctx_ptr to skb. Note, we do however continue to
disable/enable preemption around actual BPF program running to account
for map updates.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only TCP sockets have been tested and at the moment the state change
callback only handles TCP sockets. This adds a check to ensure that
sockets actually being added are TCP sockets.
For net-next we can consider UDP support.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now sctp processes icmp redirect packet in sctp_icmp_redirect where
it calls sctp_transport_dst_check in which tp->dst can be released.
The problem is before calling sctp_transport_dst_check, it doesn't
check sock_owned_by_user, which means tp->dst could be freed while
a process is accessing it with owning the socket.
An use-after-free issue could be triggered by this.
This patch is to fix it by checking sock_owned_by_user before calling
sctp_transport_dst_check in sctp_icmp_redirect, so that it would not
release tp->dst if users still hold sock lock.
Besides, the same issue fixed in commit 45caeaa5ac ("dccp/tcp: fix
routing redirect race") on sctp also needs this check.
Fixes: 55be7a9c60 ("ipv4: Add redirect support to all protocol icmp error handlers")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJZ6bO8AAoJELDendYovxMvzJgH/3QHVFMmmZnEpqpet6Om/h3Z
YuhrLTuXRL/dz6IA9u0PXOL83k3qnQKzmy4OZJL/BuT+ZGXZAJge0nLhC+sHc5CR
SrWFSee0Ut1qM1Khenfi2rn4M3F/Hc3m9lLU5KsewEflJ+MMw86RSKAPD3Xc6w0u
Kq6ejczfBvFNz1KErCO+IRc5A25ouNJZDNVwrMrJ5QXXJ2rPGFS+3TIilwu51kfQ
ux/s3frm2bNxFabkOtAZzxkYMYj9RRTDewBZocGhPmih0WWkquVbhwuxl9mf2nd0
AeFWbvMnZcq86Ra9zhtLQg1Gu7SSI/0vq7JnZtIsZw8b5YThG3V9s14fkWhJrgE=
=xWgh
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.14c-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fix from Juergen Gross:
"A fix for the Xen pv network drivers (frontend and backend) avoiding
the network connection to become unusable due to an illegal MTU"
* tag 'for-linus-4.14c-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen-netfront, xen-netback: Use correct minimum MTU values
-----BEGIN PGP SIGNATURE-----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=wFHG
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-for-v4.14-rc6' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Standard fixes pull for rc6: one regression fix for amdgpu, a bunch of
nouveau fixes that I'd missed a pull req for from Ben last week, some
exynos regression fixes, and a few fixes for i915"
* tag 'drm-fixes-for-v4.14-rc6' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau/fbcon: fix oops without fbdev emulation
Revert "drm/amdgpu: discard commands of killed processes"
drm/i915: Use a mask when applying WaProgramL3SqcReg1Default
drm/i915: Report -EFAULT before pwrite fast path into shmemfs
drm/i915/cnl: Fix PLL initialization for HDMI.
drm/i915/cnl: Fix PLL mapping.
drm/i915: Use bdw_ddi_translations_fdi for Broadwell
drm/i915: Fix eviction when the GGTT is idle but full
drm/i915/gvt: Fix GPU hang after reusing vGPU instance across different guest OS
drm/exynos: Clear drvdata after component unbind
drm/exynos: Fix potential NULL pointer dereference in suspend/resume paths
drm/nouveau/kms/nv50: fix oops during DP IRQ handling on non-MST boards
drm/nouveau/bsp/g92: disable by default
drm/nouveau/mmu: flush tlbs before deleting page tables
Pull i2c fixes from Wolfram Sang:
"A couple of bugfixes for I2C drivers.
Because the changes for the piix4 driver are larger than usual, the
patches have been in linux-next for more than a week with no reports
coming in. The rest is usual stuff"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: omap: Fix error handling for clk_get()
i2c: piix4: Disable completely the IMC during SMBUS_BLOCK_DATA
i2c: piix4: Fix SMBus port selection for AMD Family 17h chips
i2c: imx: fix misleading bus recovery debug message
i2c: imx: use IRQF_SHARED mode to request IRQ
i2c: ismt: Separate I2C block read from SMBus block read
Pull key handling fixes from James Morris:
"This includes a fix for the capabilities code from Colin King, and a
set of further fixes for the keys subsystem. From David:
- Fix a bunch of places where kernel drivers may access revoked
user-type keys and don't do it correctly.
- Fix some ecryptfs bits.
- Fix big_key to require CONFIG_CRYPTO.
- Fix a couple of bugs in the asymmetric key type.
- Fix a race between updating and finding negative keys.
- Prevent add_key() from updating uninstantiated keys.
- Make loading of key flags and expiry time atomic when not holding
locks"
* 'fixes-v4.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
commoncap: move assignment of fs_ns to avoid null pointer dereference
pkcs7: Prevent NULL pointer dereference, since sinfo is not always set.
KEYS: load key flags and expiry time atomically in proc_keys_show()
KEYS: Load key expiry time atomically in keyring_search_iterator()
KEYS: load key flags and expiry time atomically in key_validate()
KEYS: don't let add_key() update an uninstantiated key
KEYS: Fix race between updating and finding a negative key
KEYS: checking the input id parameters before finding asymmetric key
KEYS: Fix the wrong index when checking the existence of second id
security/keys: BIG_KEY requires CONFIG_CRYPTO
ecryptfs: fix dereference of NULL user_key_payload
fscrypt: fix dereference of NULL user_key_payload
lib/digsig: fix dereference of NULL user_key_payload
FS-Cache: fix dereference of NULL user_key_payload
KEYS: encrypted: fix dereference of NULL user_key_payload
The patch edf10919 [dmaengine: altera: fix spinlock usage] missed to
change 2 occurrences of spin_unlock_bh() to spin_unlock_irqrestore().
This patch fixes this by moving to the IRQ-safe call in the error
paths as well.
Fixes: edf10919 (dmaengine: altera: fix spinlock usage)
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Sylvain Lesne <lesne@alse-fr.com>
[add fixes tag and fix typo in log]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This reverts a problematic commit modifying the turbostat
utility that went in during the 4.13 cycle (Len Brown).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=i876
-----END PGP SIGNATURE-----
Merge tag 'pm-4.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"This reverts a problematic commit modifying the turbostat utility that
went in during the 4.13 cycle (Len Brown)"
* tag 'pm-4.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "tools/power turbostat: stop migrating, unless '-m'"
Because many of RCU's files have not been included into docbook, a
number of errors have accumulated. This commit fixes them.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 764f80798b ("doc: Add RCU files to docbook-generation files")
added :external: options for RCU source files in the file
Documentation/core-api/kernel-api.rst. However, this now means nothing,
so this commit removes them.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Akira Yokosawa <akiyks@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This introduces a "register private expedited" membarrier command which
allows eventual removal of important memory barrier constraints on the
scheduler fast-paths. It changes how the "private expedited" membarrier
command (new to 4.14) is used from user-space.
This new command allows processes to register their intent to use the
private expedited command. This affects how the expedited private
command introduced in 4.14-rc is meant to be used, and should be merged
before 4.14 final.
Processes are now required to register before using
MEMBARRIER_CMD_PRIVATE_EXPEDITED, otherwise that command returns EPERM.
This fixes a problem that arose when designing requested extensions to
sys_membarrier() to allow JITs to efficiently flush old code from
instruction caches. Several potential algorithms are much less painful
if the user register intent to use this functionality early on, for
example, before the process spawns the second thread. Registering at
this time removes the need to interrupt each and every thread in that
process at the first expedited sys_membarrier() system call.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Before trying to use CDC union descriptor, try to validate whether that it
is sane by checking that intf->altsetting->extra is big enough and that
descriptor bLength is not too big and not too small.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Introduce a device table used for blacklisting devices. We currently
blacklist the motion sensor subdevice of THQ Udraw and Sony ds3/ds4.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
[dtor: siwtched to blacklist built on input_device_id and using
input_match_device_id()]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's allow matching input devices on their property bits, both in-kernel
and when generating module aliases.
Tested-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Factor out and export input_match_device_id() so that modules may use it.
It will be needed by joydev to blacklist accelerometers in composite
devices.
Tested-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Goodix panel triggers an interrupt on touch events. However, its
registers will contain the valid values a short time after the
interrupt, and not when it's raised. At that moment, the 'buffer status'
bit is set.
Previously, if the 'buffer status' bit was not set when the registers
were read, the data was discarded and no input event was emitted,
causing "finger down" or "finger up" events to be missed sometimes.
This went unnoticed until v4.9, as the DesignWare I2C driver commonly
used with this driver had enough latency for that bug to never trigger
until commit 2702ea7dbe ("i2c: designware: wait for disable/enable only
if necessary").
Now, in the IRQ handler we will poll (with a timeout) the 'buffer status'
bit and process the data of the panel as soon as this bit gets set.
Note that the Goodix panel will send a few spurious interrupts after the
'finger up' event, in which the 'buffer status' bit will never be set.
Cc: Bastien Nocera <hadess@hadess.net>
Cc: russianneuromancer@ya.ru
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
[hdegoede@redhat.com: Change poll loop to use jiffies,
add comment about typical poll time]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[dtor: rearranged control flow a bit to avoid explicit goto and double
check]
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that we have a platform_device_id table and multiple supported ids
we should be using MODULE_DEVICE_TABLE instead of MODULE_ALIAS.
This fixes a regression on Bay and Cherry Trail devices, where the power
button is now enumerated as an "axp221-pek" and it was impossible to
wakeup these devices from suspend since the module did not load.
Fixes: c3cc94470b ("Input: axp20x-pek - add support for AXP221 PEK")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently, enabling keypad interrupts is one of the first operations
done on the keypad, even before the interrupt is requested, so there is
a small time window where the keypad can fire interrupts but the driver
is not yet ready to handle them. It's fine for level interrupts because
they will be handled anyway, but not so much for edge ones.
This commit modifies and moves the function in charge of configuring the
keypad. Enabling interrupts is now the last thing done on the keypad,
and after the interrupt has been requested by the driver.
Writing to the config register was also used to determine if the device
was indeed present on the bus or not, this has been replaced by reading
the lock/event count register to keep the same functionality.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull parisc fixes from Helge Deller:
"Three small important fixes for the parisc architecture:
- Export __cmpxchg_u64() symbol on 32bit kernel too. This unbreaks
building the kernel with ixgbe kernel module. From Guenter Roeck.
- Fix 64-bit atomic cmpxchg kernel helper function for 32-bit kernel
in LWS code for userspace. This unbreaks e.g. the 64-bit variant of
the glibc function __sync_fetch_and_add() with a 32-bit parisc
kernel. From John David Anglin, tagged for backport to v3.13+.
- Detect nonsynchronous CPU-internal cr16 cycle counters more
reliable. This avoids stalled CPU warnings by the kernel soft
lockup detector. From me, tagged for backport to v4.13+"
* 'parisc-4.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix detection of nonsynchronous cr16 cycle counters
parisc: Export __cmpxchg_u64 unconditionally
parisc: Fix double-word compare and exchange in LWS code on 32-bit kernels
We've got slightly more fixes than wished, but heading to a good
shape. Most of changes are about HD-audio fixes, one for a buggy code
that went into 4.13, and another for avoiding a crash due to buggy
BIOS.
Apart from HD-audio, a sequencer core change that is only for UP
config (which must be pretty rare nowadays), and a USB-audio quirk as
usual.
-----BEGIN PGP SIGNATURE-----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=YGib
-----END PGP SIGNATURE-----
Merge tag 'sound-4.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"We've got slightly more fixes than wished, but heading to a good
shape. Most of changes are about HD-audio fixes, one for a buggy code
that went into 4.13, and another for avoiding a crash due to buggy
BIOS.
Apart from HD-audio, a sequencer core change that is only for UP
config (which must be pretty rare nowadays), and a USB-audio quirk as
usual"
* tag 'sound-4.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix incorrect TLV callback check introduced during set_fs() removal
ALSA: hda: Remove superfluous '-' added by printk conversion
ALSA: hda: Abort capability probe at invalid register read
ALSA: seq: Enable 'use' locking in all configurations
ALSA: usb-audio: Add native DSD support for Pro-Ject Pre Box S2 Digital
Add 12V regulator to backlight allowing the power supply
for the backlight to be found.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zIL3
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Pull "Renesas ARM Based SoC Fixes for v4.14" from Simon Horman:
Add 12V regulator to backlight allowing the power supply
for the backlight to be found.
* tag 'renesas-fixes-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: salvator-common: add 12V regulator to backlight
The commit afece3ab9a ("PM / Domains: Add time accounting to various
genpd states") causes a boot regression for ux500.
The problem occurs when the ux500 machine code calls pm_genpd_init(), which
since the above change triggers a call to ktime_get(). More precisely,
because ux500 initializes PM domains in the init_IRQ() phase of the boot,
timekeeping has not yet been initialized.
Fix the problem by moving the initialization of the PM domains to after
timekeeping has been initialized.
Fixes: afece3ab9a ("PM / Domains: Add time accounting to various genpd..")
Cc: Thara Gopinath <thara.gopinath@linaro.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These platforms provide a clock to their watchdog, in each
case this is the peripheral clock (PCLK), so explicitly
name the clock in the device tree.
Take this opportunity to add the "faraday,ftwdt010"
compatible as fallback to the watchdog IP blocks.
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix SoCFPGA reset controller for 64-bit systems. This patch removes the
assumption that BITS_PER_LONG is 32, which is not the case on Stratix10.
-----BEGIN PGP SIGNATURE-----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=VEC4
-----END PGP SIGNATURE-----
Merge tag 'reset-fixes-for-4.14-2' of git://git.pengutronix.de/git/pza/linux into fixes
Pull "Reset controller fixes for v4.14" from Philipp Zabel:
Fix SoCFPGA reset controller for 64-bit systems. This patch removes the
assumption that BITS_PER_LONG is 32, which is not the case on Stratix10.
* tag 'reset-fixes-for-4.14-2' of git://git.pengutronix.de/git/pza/linux:
reset: socfpga: fix for 64-bit compilation
exceed 3.0V, so they got fixed to not be at 3.3V
And Arnd found a typo in the recently added iommu nodes.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlnmSIIQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgeaQB/9JDBD545VzXqsNixEnJOcT+X8sUZpu6OmT
j3v5kJDPOXLfSP/Ci9S10ldix/JUBZoT2fRJCK5QAzo+NnjYWrC5qPAwGVU90TqY
KxFZu4f1763AU2ZLw9nGJlFeVHrjhpFdYfe9GpPPLmndjM32cRdGCRI5zDaSB7s8
popUs6qNGvI5Q770x4/xTfEqDlfdQhmYyNfWumji7ACfLTHYZnpyq0SN/o4qp/rg
UJaPx/7PGzHIDSrEKRE3i+waG3d7Ix4th9jkmrYFAK2nIiySlZg9WIKWEOqqt+sf
H8W3ygdlaYZlzIPJhY2r6/W1rQoJSLxxKColLrV32hDkjPfcFon5
=YPhS
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rockchip-dts64fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Pull "Rockchip dts64 Fixes for 4.14 part 2" from Heiko Stübner:
The vqmmc voltages on rk3399 pose a risk for the chip if they
exceed 3.0V, so they got fixed to not be at 3.3V
And Arnd found a typo in the recently added iommu nodes.
* tag 'v4.14-rockchip-dts64fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: fix typo in iommu nodes
arm64: dts: rockchip: correct vqmmc voltage for rk3399 platforms
- Fix the legacy PCI interrupt numbers for i.MX7. The numbers were
wrongly coded in an inverted order than what Reference Manual tells.
It causes problem for PCI devices using legacy interrupt.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ5F/UAAoJEFBXWFqHsHzOQCwH/3SfH9+Akv0M0noDacXyzD+2
MvQGppmagSl8TNeeP0kYc7wk2TeuYc24LJyEAR5xhDwkxL5LGLbXtMr5LqxJszcB
smQqS9MHpyuIboepw3xBcDBi+vOy9fmrLv7WUnM3yEXWh6gR6VYYU0D4jK/xYmUo
urH0j8etj5sao02s7D3O0iSEvaxIxtjOHB6i9fCcHNtJXo7iw2lv0XhyQhE73IX2
LFkRCdtj8EBb+gjPQrXMUE0gn67mvxuzwOOVunEGwl/13cI3WQoRh7pugTB7NBNQ
fVyBW/8TLOqkKjPinqbnyMVdS1rwel+pfC2Q8jVnjfGNjrmnCxWbcR4R8YqQJsw=
=+4ri
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Pull "i.MX fixes for 4.14" from Shawn Guo:
- Fix the legacy PCI interrupt numbers for i.MX7. The numbers were
wrongly coded in an inverted order than what Reference Manual tells.
It causes problem for PCI devices using legacy interrupt.
* tag 'imx-fixes-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx7d: Invert legacy PCI irq mapping
Two device tree related fixes:
- One on Armada 38x using a other compatible string for I2C in order
to cover an errata.
- One for Armada 7K/8K fixing a typo on interrupt-map property for
PCIe leading to fail PME and AER root port service initialization
And the last one for the mbus fixing the window size calculation when
it exceed 32bits
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWeDbriMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71RAJAJ9TyT+GrMdf
HsM7V74bSWYAUlWZ0ACcCWjIdnbVlinP+iuVS462du4HpU0=
=2AQR
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.14-2' of git://git.infradead.org/linux-mvebu into fixes
Pull "mvebu fixes for 4.14 (part 2)" from Gregory CLEMENT
Two device tree related fixes:
- One on Armada 38x using a other compatible string for I2C in order
to cover an errata.
- One for Armada 7K/8K fixing a typo on interrupt-map property for
PCIe leading to fail PME and AER root port service initialization
And the last one for the mbus fixing the window size calculation when
it exceed 32bits
* tag 'mvebu-fixes-4.14-2' of git://git.infradead.org/linux-mvebu:
bus: mbus: fix window size calculation for 4GB windows
ARM: dts: Fix I2C repeated start issue on Armada-38x
arm64: dts: marvell: fix interrupt-map property for Armada CP110 PCIe controller
- one DT phy address fix for the new sama5d27 som1 ek
- two DT ADC patches that were forgotten while moving to
hardware triggers for sama5d2 (iio changes already applied)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ24QUAAoJEAf03oE53VmQHGAIAJcmiYj0qsO8ModMQjFSBR6Q
YW/7r8TAvJDgABWdu1RcpBFhGuZepYEBNToDtYAP/fLWJ14s0PqpJFM0JKZWUh4Q
SsX6zKuUcER09QyvFRmRRtF6HlyL/X84Rkf6wUfNvdaUOEUNF4qotG/6281ZlHxF
+RdKQkvx6Tv9oZAKyk9dwiYj6YtmGhZ4JQNoj+4yCqQ+ImLVlbfkLGMSPIzE1/KO
3+crrYTFl+hFcy+66hFgMz7RvbH0k+6djBkg2PDV1aD2EklStP6V98Wpxwm+fYhz
ka2Up5w+aDlp5Snif7+pH6oP0A1FvveTlv3t1wp3q9B2iqF7Ps4A+9J1L7p0n/4=
=W4R5
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Fixes: second batch for 4.14:
- one DT phy address fix for the new sama5d27 som1 ek
- two DT ADC patches that were forgotten while moving to
hardware triggers for sama5d2 (iio changes already applied)
* tag 'at91-fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: dts: at91: sama5d2: add ADC hw trigger edge type
ARM: dts: at91: sama5d2_xplained: enable ADTRG pin
ARM: dts: at91: at91-sama5d27_som1: fix PHY ID
please pull the following:
- Loic fixes the console path on the Raspberry Pi 3 which was not correctly set
and would cause all sorts of confusion between the Bluetooth controller and the
kernel console
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJZ2AFxAAoJEIfQlpxEBwcEFcsP/375LxHvuaw3Uo6HlrJ77+sF
RM1E6DfDPkcfk9MQ+U3UUKWBk66HU76epVIX+8H/ERxB0Y7gShhHG7wX54YzsA5Z
Wh/KiHC0HUGAhZWguOK88JSj9cO90k35tSp+JHktVbtI6lf2r14ZQeMgcnulFuHM
rAbBmC+ap2ACOtGKg/Glj3205yqhllxUEBU3pu5kDZaRWTGqifJaa4DyKGGDx7KS
YDqAYs3EB6i753CDwoztxtQj1gEVrFSmLEcbdrUnAPGFTv2IDy2faxjpfAdus6q4
NMzSa0A4MRsEM/FaxYyF64y0SQyqeEFZ7Znj8bU7mEJrE0cpjPEXrRRqwCyceIv3
4FjEIkd2x8b+drIm6yXaMAQuMSuIsWwO2RUGJnF8JG8XXMuUDL5bZpnn2RrsTmcb
RjcOddgPgQusLJnRB86SkHWts8Bu/a8Q+gQQgfZsVXtpqZvyjEw3GPWnPoQEKmCI
ZvDbIP7VQe+niCGMBu9jez+sNjOkvUz0SyWnPg/Va0lofKifp4ZZxlX9SwRFOQAy
ii3b5O+WYCVNnWgGOBkSOHbqb6nnrpwgQk2CsdRuB86c/yzhv3/dpr+cXPSX0h+q
4c5fNxfcJThgSL86lm/L/SZ1Fuc+MFbYaKcLJLMY1JZ7kxUcaKMqrRUojh9/AoiU
89ksb1UE2vTclL8q1nyY
=GeQi
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.14/devicetree-fixes' of http://github.com/Broadcom/stblinux into fixes
Pull "Broadcom devicetree fixes for 4.14" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoC Device Tree fixes for 4.14,
please pull the following:
- Loic fixes the console path on the Raspberry Pi 3 which was not correctly set
and would cause all sorts of confusion between the Bluetooth controller and the
kernel console
* tag 'arm-soc/for-4.14/devicetree-fixes' of http://github.com/Broadcom/stblinux:
ARM: dts: bcm283x: Fix console path on RPi3
Now when peeling off an association to the sock in another netns, all
transports in this assoc are not to be rehashed and keep use the old
key in hashtable.
As a transport uses sk->net as the hash key to insert into hashtable,
it would miss removing these transports from hashtable due to the new
netns when closing the sock and all transports are being freeed, then
later an use-after-free issue could be caused when looking up an asoc
and dereferencing those transports.
This is a very old issue since very beginning, ChunYu found it with
syzkaller fuzz testing with this series:
socket$inet6_sctp()
bind$inet6()
sendto$inet6()
unshare(0x40000000)
getsockopt$inet_sctp6_SCTP_GET_ASSOC_ID_LIST()
getsockopt$inet_sctp6_SCTP_SOCKOPT_PEELOFF()
This patch is to block this call when peeling one assoc off from one
netns to another one, so that the netns of all transport would not
go out-sync with the key in hashtable.
Note that this patch didn't fix it by rehashing transports, as it's
difficult to handle the situation when the tuple is already in use
in the new netns. Besides, no one would like to peel off one assoc
to another netns, considering ipaddrs, ifaces, etc. are usually
different.
Reported-by: ChunYu Wang <chunwang@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
bpf: Fix for BPF devmap percpu allocation splat
The set fixes a splat in devmap percpu allocation when we alloc
the flush bitmap. Patch 1 is a prerequisite for the fix in patch 2,
patch 1 is rather small, so if this could be routed via -net, for
example, with Tejun's Ack that would be good. Patch 3 gets rid of
remaining PCPU_MIN_UNIT_SIZE checks, which are percpu allocator
internals and should not be used.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
PCPU_MIN_UNIT_SIZE is an implementation detail of the percpu
allocator. Given we support __GFP_NOWARN now, lets just let
the allocation request fail naturally instead. The two call
sites from BPF mistakenly assumed __GFP_NOWARN would work, so
no changes needed to their actual __alloc_percpu_gfp() calls
which use the flag already.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported that syzkaller was able to trigger a splat on
devmap percpu allocation due to illegal/unsupported allocation
request size passed to __alloc_percpu():
[ 70.094249] illegal size (32776) or align (8) for percpu allocation
[ 70.094256] ------------[ cut here ]------------
[ 70.094259] WARNING: CPU: 3 PID: 3451 at mm/percpu.c:1365 pcpu_alloc+0x96/0x630
[...]
[ 70.094325] Call Trace:
[ 70.094328] __alloc_percpu_gfp+0x12/0x20
[ 70.094330] dev_map_alloc+0x134/0x1e0
[ 70.094331] SyS_bpf+0x9bc/0x1610
[ 70.094333] ? selinux_task_setrlimit+0x5a/0x60
[ 70.094334] ? security_task_setrlimit+0x43/0x60
[ 70.094336] entry_SYSCALL_64_fastpath+0x1a/0xa5
This was due to too large max_entries for the map such that we
surpassed the upper limit of PCPU_MIN_UNIT_SIZE. It's fine to
fail naturally here, so switch to __alloc_percpu_gfp() and pass
__GFP_NOWARN instead.
Fixes: 11393cc9b9 ("xdp: Add batching support to redirect map")
Reported-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Shankara Pailoor <sp3485@columbia.edu>
Reported-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an option for pcpu_alloc() to support __GFP_NOWARN flag.
Currently, we always throw a warning when size or alignment
is unsupported (and also dump stack on failed allocation
requests). The warning itself is harmless since we return
NULL anyway for any failed request, which callers are
required to handle anyway. However, it becomes harmful when
panic_on_warn is set.
The rationale for the WARN() in pcpu_alloc() is that it can
be tracked when larger than supported allocation requests are
made such that allocations limits can be tweaked if warranted.
This makes sense for in-kernel users, however, there are users
of pcpu allocator where allocation size is derived from user
space requests, e.g. when creating BPF maps. In these cases,
the requests should fail gracefully without throwing a splat.
The current work-around was to check allocation size against
the upper limit of PCPU_MIN_UNIT_SIZE from call-sites for
bailing out prior to a call to pcpu_alloc() in order to
avoid throwing the WARN(). This is bad in multiple ways since
PCPU_MIN_UNIT_SIZE is an implementation detail, and having
the checks on call-sites only complicates the code for no
good reason. Thus, lets fix it generically by supporting the
__GFP_NOWARN flag that users can then use with calling the
__alloc_percpu_gfp() helper instead.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Tejun Heo <tj@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gavin Shan