Pull input fixes from Dmitry Torokhov.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: vmmouse - remove port reservation
Input: elantech - add more IC body types to the list
Input: wacom_w8001 - ignore invalid pen data packets
Input: wacom_w8001 - w8001_MAX_LENGTH should be 13
Input: xpad - fix oops when attaching an unknown Xbox One gamepad
MAINTAINERS: add Pali Rohár as reviewer of ALPS PS/2 touchpad driver
Input: add HDMI CEC specific keycodes
Input: add BUS_CEC type
Input: xpad - fix rumble on Xbox One controllers with 2015 firmware
The VMWare EFI BIOS will expose port 0x5658 as an ACPI resource. This
causes the port to be reserved by the APCI module as the system comes up,
making it unavailable to be reserved again by other drivers, thus
preserving this VMWare port for special use in a VMWare guest.
This port is designed to be shared among multiple VMWare services, such as
the VMMOUSE. Because of this, VMMOUSE should not try to reserve this port
on its own.
The VMWare non-EFI BIOS does not do this to preserve compatibility with
existing/legacy VMs. It is known that there is small chance a VM may be
configured such that these ports get reserved by other non-VMWare devices,
and if this ever happens, the result is undefined.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Cc: <stable@vger.kernel.org> # 4.1-
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchpad in HP Pavilion 14-ab057ca reports it's version as 12 and
according to Elan both 11 and 12 are valid IC types and should be
identified as hw_version 4.
Reported-by: Patrick Lessard <Patrick.Lessard@cogeco.com>
Tested-by: Patrick Lessard <Patrick.Lessard@cogeco.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ThinkPad X60 Tablet PC (pen only device) sometime posts
packets that are larger than W8001_PKTLEN_TPCPEN.
Reported-by: Chris J Arges <christopherarges@gmail.com>
Tested-by: Chris J Arges <christopherarges@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Somehow the patch that added two-finger touch support forgot to update
W8001_MAX_LENGTH from 11 to 13.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Xbox One controllers have multiple interfaces which all have the
same class, subclass, and protocol. One of the these interfaces
has only a single endpoint. When Xpad attempts to bind to this
interface, it causes an oops when trying initialize the output URB
by trying to access the second endpoint's descriptor.
This situation was avoided for known Xbox One devices by checking
the XTYPE constant associated with the VID and PID tuple. However,
this breaks when new or previously unknown Xbox One controllers
are attached to the system.
This change addresses the problem by deriving the XTYPE for Xbox
One controllers based on the interface protocol before checking
the interface number.
Fixes: 1a48ff81b3 ("Input: xpad - add support for Xbox One controllers")
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Xbox One controllers that shipped with or were upgraded to the 2015
firmware discard the current rumble packets we send. This patch changes
the Xbox One rumble packet to a form that both the newer and older
firmware will accept.
It is based on changes made to support newer Xbox One controllers in
the SteamOS brewmaster-4.1 kernel branch.
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull more input subsystem updates from Dmitry Torokhov:
"Just a few more driver fixes; new drivers will be coming in the next
merge window"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: pwm-beeper - fix - scheduling while atomic
Input: xpad - xbox one elite controller support
Input: xpad - add more third-party controllers
Input: xpad - prevent spurious input from wired Xbox 360 controllers
Input: xpad - move pending clear to the correct location
Input: uinput - handle compat ioctl for UI_SET_PHYS
Pwm config may sleep so defer it using a worker.
On a Freescale i.MX53 based board we ran into "BUG: scheduling while
atomic" because input_inject_event locks interrupts, but
imx_pwm_config_v2 sleeps.
Tested on Freescale i.MX53 SoC with 4.6.0.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
added the according id and incresed XPAD_PKT_LEN to 64 as the elite
controller sends at least 33 byte messages [1].
Verified to be working by [2].
[1]: https://franticrain.github.io/sniffs/XboxOneSniff.html
[2]: https://github.com/paroj/xpad/issues/23
Signed-off-by: Pierre-Loup A. Griffais <eduke32@plagman.net>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
After initially connecting a wired Xbox 360 controller or sending it
a command to change LEDs, a status/response packet is interpreted as
controller input. This causes the state of buttons represented in
byte 2 of the controller data packet to be incorrect until the next
valid input packet. Wireless Xbox 360 controllers are not affected.
Writing a new value to the LED device while holding the Start button
and running jstest is sufficient to reproduce this bug. An event will
come through with the Start button released.
Xboxdrv also won't attempt to read controller input from a packet
where byte 0 is non-zero. It also checks that byte 1 is 0x14, but
that value differs between wired and wireless controllers and this
code is shared by both. I think just checking byte 0 is enough to
eliminate unwanted packets.
The following are some examples of 3-byte status packets I saw:
01 03 02
02 03 00
03 03 03
08 03 00
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull thermal management updates from Zhang Rui:
- Introduce generic ADC thermal driver, based on OF thermal (Laxman
Dewangan)
- Introduce new thermal driver for Tango chips (Marc Gonzalez)
- Rockchip driver support for RK3399, RK3366, and some fixes (Caesar
Wang, Elaine Zhang and Shawn Lin)
- Add CPU power cooling model to Mediatek thermal driver (Dawei Chien)
- Wider usage of dev_thermal_zone_of_sensor_register (Eduardo Valentin)
- TI thermal driver gained a new maintainer (Keerthy).
- Enabled powerclamp driver by checking CPU feature and package cstate
counter instead of CPU whitelist (Jacob Pan)
- Various fixes on thermal governor, OF thermal, Tegra, and RCAR
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (50 commits)
thermal: tango: initialize TEMPSI_CFG
thermal: rockchip: use the usleep_range instead of udelay
thermal: rockchip: add the notes for better reading
thermal: rockchip: Support RK3366 SoCs in the thermal driver
thermal: rockchip: handle the power sequence for tsadc controller
thermal: rockchip: update the tsadc table for rk3399
thermal: rockchip: fixes the code_to_temp for tsadc driver
thermal: rockchip: disable thermal->clk in err case
thermal: tegra: add Tegra132 specific SOC_THERM driver
thermal: fix ptr_ret.cocci warnings
thermal: mediatek: Add cpu dynamic power cooling model.
thermal: generic-adc: Add ADC based thermal sensor driver
thermal: generic-adc: Add DT binding for ADC based thermal sensor
thermal: tegra: fix static checker warning
thermal: tegra: mark PM functions __maybe_unused
thermal: add temperature sensor support for tango SoC
thermal: hisilicon: fix IRQ imbalance enabling
thermal: hisilicon: support to use any sensor
thermal: rcar: Remove binding docs for r8a7794
thermal: tegra: add PM support
...
This set of changes introduces an atomic API to the PWM subsystem. This
is influenced by the DRM atomic API that was introduced a while back,
though it is obviously a lot simpler. The fundamental idea remains the
same, though: drivers provide a single callback to implement the atomic
configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware. Many
use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are postponed
to v4.8.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sxT9
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes introduces an atomic API to the PWM subsystem.
This is influenced by the DRM atomic API that was introduced a while
back, though it is obviously a lot simpler. The fundamental idea
remains the same, though: drivers provide a single callback to
implement the atomic configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware.
Many use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are
postponed to v4.8"
* tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (30 commits)
pwm: Add information about polarity, duty cycle and period to debugfs
pwm: Switch to the atomic API
pwm: Update documentation
pwm: Add core infrastructure to allow atomic updates
pwm: Add hardware readout infrastructure
pwm: Move the enabled/disabled info into pwm_state
pwm: Introduce the pwm_state concept
pwm: Keep PWM state in sync with hardware state
ARM: Explicitly apply PWM config extracted from pwm_args
drm: i915: Explicitly apply PWM config extracted from pwm_args
input: misc: pwm-beeper: Explicitly apply PWM config extracted from pwm_args
input: misc: max8997: Explicitly apply PWM config extracted from pwm_args
backlight: lm3630a: explicitly apply PWM config extracted from pwm_args
backlight: lp855x: Explicitly apply PWM config extracted from pwm_args
backlight: lp8788: Explicitly apply PWM config extracted from pwm_args
backlight: pwm_bl: Use pwm_get_args() where appropriate
fbdev: ssd1307fb: Use pwm_get_args() where appropriate
regulator: pwm: Use pwm_get_args() where appropriate
leds: pwm: Use pwm_get_args() where appropriate
input: misc: max77693: Use pwm_get_args() where appropriate
...
When running a 32-bit userspace on a 64-bit kernel, the UI_SET_PHYS
ioctl needs to be treated with special care, as it has the pointer
size encoded in the command.
Signed-off-by: Ricky Liang <jcliang@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages. This
means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than
(as we did before) try to emulate it by switching the line
to an input to get high impedance. This is also documented
throughly in Documentation/gpio/driver.txt for those of you
who did not understand one word of what I just wrote.
- Start to do away with the unnecessarily complex and
unitelligible ARCH_REQUIRE_GPIOLIB and
ARCH_WANT_OPTIONAL_GPIOLIB, another evolutional artifact from
the time when the GPIO subsystem was unmaintained. Archs can
now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs
ACKed the changes immediately so these are included in this
pull request.
- Advancing the use of the data pointer inside the GPIO device
for storing driver data by switching the PowerPC, Super-H
Unicore and a few other subarches or subsystem drivers in
ALSA SoC, Input, serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the
GPIO lines, so that each GPIO descriptor knows - if this
callback is implemented - whether the line is input or
output. This also reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names,
from the device tree. (Platform data has been supported for
a while.) I bet we will get a similar mechanism for ACPI
one of those days. This makes is possible to get sensible
producer names for e.g. GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and
now also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain
and in some cases open source.
- Implement the .get_direction() callback for a few more drivers
like PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized
those who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where
they belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z4d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel cycle v4.7:
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages.
This means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than (as we
did before) try to emulate it by switching the line to an input to
get high impedance.
This is also documented throughly in Documentation/gpio/driver.txt
for those of you who did not understand one word of what I just
wrote.
- Start to do away with the unnecessarily complex and unitelligible
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another
evolutional artifact from the time when the GPIO subsystem was
unmaintained.
Archs can now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs ACKed
the changes immediately so these are included in this pull request.
- Advancing the use of the data pointer inside the GPIO device for
storing driver data by switching the PowerPC, Super-H Unicore and
a few other subarches or subsystem drivers in ALSA SoC, Input,
serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the GPIO
lines, so that each GPIO descriptor knows - if this callback is
implemented - whether the line is input or output. This also
reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names, from
the device tree. (Platform data has been supported for a while).
I bet we will get a similar mechanism for ACPI one of those days.
This makes is possible to get sensible producer names for e.g.
GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and now
also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain and in some
cases open source.
- Implement the .get_direction() callback for a few more drivers like
PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized those
who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where they
belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less"
* tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits)
MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
gpio: zevio: make it explicitly non-modular
gpio: timberdale: make it explicitly non-modular
gpio: stmpe: make it explicitly non-modular
gpio: sodaville: make it explicitly non-modular
pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms
gpio: dt-bindings: add wd,mbl-gpio bindings
gpio: of: make it possible to name GPIO lines
gpio: make gpiod_to_irq() return negative for NO_IRQ
gpio: xgene: implement .get_direction()
gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
gpio: tegra: Implement gpio_get_direction callback
gpio: set up initial state from .get_direction()
gpio: rename gpio-generic.c into gpio-mmio.c
gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
gpio: dwapb: add gpio-signaled acpi event support
gpio: dwapb: convert device node to fwnode
gpio: dwapb: remove name from dwapb_port_property
gpio/qoriq: select IRQ_DOMAIN
...
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Jens Thiele <karme@karme.de>
Cc: linux-input@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Call pwm_apply_args() just after requesting the PWM device so that the
polarity and period are initialized according to the information
provided in pwm_args.
This is an intermediate state, and pwm_apply_args() should be dropped as
soon as the atomic PWM infrastructure is in place and the driver makes
use of it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Call pwm_apply_args() just after requesting the PWM device so that the
polarity and period are initialized according to the information
provided in pwm_args.
This is an intermediate state, and pwm_apply_args() should be dropped as
soon as the atomic PWM infrastructure is in place and the driver makes
use of it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The PWM framework has clarified the concept of reference PWM config (the
platform dependent config retrieved from the DT or the PWM lookup table)
and real PWM state.
Use pwm_get_args() when the PWM user wants to retrieve this reference
config and not the current state.
This is part of the rework allowing the PWM framework to support
hardware readout and expose real PWM state even when the PWM has just
been requested (before the user calls pwm_config/enable/disable()).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Pull x86 asm updates from Ingo Molnar:
"The main changes in this cycle were:
- MSR access API fixes and enhancements (Andy Lutomirski)
- early exception handling improvements (Andy Lutomirski)
- user-space FS/GS prctl usage fixes and improvements (Andy
Lutomirski)
- Remove the cpu_has_*() APIs and replace them with equivalents
(Borislav Petkov)
- task switch micro-optimization (Brian Gerst)
- 32-bit entry code simplification (Denys Vlasenko)
- enhance PAT handling in enumated CPUs (Toshi Kani)
... and lots of other cleanups/fixlets"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
x86/arch_prctl/64: Restore accidentally removed put_cpu() in ARCH_SET_GS
x86/entry/32: Remove asmlinkage_protect()
x86/entry/32: Remove GET_THREAD_INFO() from entry code
x86/entry, sched/x86: Don't save/restore EFLAGS on task switch
x86/asm/entry/32: Simplify pushes of zeroed pt_regs->REGs
selftests/x86/ldt_gdt: Test set_thread_area() deletion of an active segment
x86/tls: Synchronize segment registers in set_thread_area()
x86/asm/64: Rename thread_struct's fs and gs to fsbase and gsbase
x86/arch_prctl/64: Remove FSBASE/GSBASE < 4G optimization
x86/segments/64: When load_gs_index fails, clear the base
x86/segments/64: When loadsegment(fs, ...) fails, clear the base
x86/asm: Make asm/alternative.h safe from assembly
x86/asm: Stop depending on ptrace.h in alternative.h
x86/entry: Rename is_{ia32,x32}_task() to in_{ia32,x32}_syscall()
x86/asm: Make sure verify_cpu() has a good stack
x86/extable: Add a comment about early exception handlers
x86/msr: Set the return value to zero when native_rdmsr_safe() fails
x86/paravirt: Make "unsafe" MSR accesses unsafe even if PARAVIRT=y
x86/paravirt: Add paravirt_{read,write}_msr()
x86/msr: Carry on after a non-"safe" MSR access fails
...
commit e7ec014a47 ("Input: twl6040-vibra - update for device tree support")
made the separate vibra DT node to a subnode of the twl6040.
It now calls of_find_node_by_name() to locate the "vibra" subnode.
This function has a side effect to call of_node_put on() for the twl6040
parent node passed in as a parameter. This causes trouble later on.
Solution: we must call of_node_get() before of_find_node_by_name()
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
fix checkpatch.pl warning about 'Prefer 'unsigned int' to bare use of
'unsigned''
Signed-off-by: Clifton Barnes <clifton.a.barnes@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
NULL pointer derefence happens when booting with DTB because the
platform data for haptic device is not set in supplied data from parent
MFD device.
The MFD device creates only platform data (from Device Tree) for itself,
not for haptic child.
Unable to handle kernel NULL pointer dereference at virtual address 0000009c
pgd = c0004000
[0000009c] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
(max8997_haptic_probe) from [<c03f9cec>] (platform_drv_probe+0x4c/0xb0)
(platform_drv_probe) from [<c03f8440>] (driver_probe_device+0x214/0x2c0)
(driver_probe_device) from [<c03f8598>] (__driver_attach+0xac/0xb0)
(__driver_attach) from [<c03f67ac>] (bus_for_each_dev+0x68/0x9c)
(bus_for_each_dev) from [<c03f7a38>] (bus_add_driver+0x1a0/0x218)
(bus_add_driver) from [<c03f8db0>] (driver_register+0x78/0xf8)
(driver_register) from [<c0101774>] (do_one_initcall+0x90/0x1d8)
(do_one_initcall) from [<c0a00dbc>] (kernel_init_freeable+0x15c/0x1fc)
(kernel_init_freeable) from [<c06bb5b4>] (kernel_init+0x8/0x114)
(kernel_init) from [<c0107938>] (ret_from_fork+0x14/0x3c)
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: <stable@vger.kernel.org>
Fixes: 104594b01c ("Input: add driver support for MAX8997-haptic")
[k.kozlowski: Write commit message, add CC-stable]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As pointed out by Richard, the changes to the comment got missed off
the absolute mode patch somehow.
Signed-off-by: Chris Diamand <chris@diamand.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Complete() will be run with interrupt enabled, so change to
spin_lock_irqsave().
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The CM109 driver reported key press events of volume up / down and
record / playback mute buttons, but no release events. Report those events
properly by handling volume and mute keys seperately. For the record and
playback mute buttons, only presses are registered by the CM109, therefore
simulate press-n-release. This fixes the volume control buttons of various
USB headsets.
Signed-off-by: Florian Euchner <florian.euchner@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since memory for a private data is allocated by kzalloc() there is no
need to fill it with zeroes immediately after the allocation.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The bitwise shift operator has lower priority than plus operator. So the
values on macros should be enclosed in parentheses.
For example, "(1 << 4 + 1)" means "(1 << (4 + 1))", but it is not expected
by the macros.
And also fix other two coding style problems reported by
scripts/checkpatch.pl.
Signed-off-by: Rui Teng <rui.teng@linux.vnet.ibm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fix spelling typos in printk from various part
of the codes.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If using IRQF_TRIGGER_FALLING, then there is a race here: if the reset
completes before we enable the IRQ, then CHG is already low and touch
will be broken.
This has been seen on Chromebook Pixel 2.
A workaround is to reconfig T18 COMMSCONFIG to enable the RETRIGEN bit
using mxt-app:
mxt-app -W -T18 44
mxt-app --backup
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A wrong decoding of the touch coordinate message causes a wrong touch
ID. Touch ID for dual touch must be 0 or 1.
According to the actual Neonode nine byte touch coordinate coding,
the state is transported in the lower nibble and the touch ID in
the higher nibble of payload byte five.
Signed-off-by: Knut Wohlrab <Knut.Wohlrab@de.bosch.com>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The mutex does not seem to be needed. twl4030-vibra doesn't
use one either.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
commit c6f39257c9 ("mfd: twl6040: Use regmap for register cache")
did remove the private cache for the vibra control registers and replaced
access within twl6040_get_vibralr_status() by calls to regmap. This is OK,
as long as twl6040_get_vibralr_status() uses already cached values or is
not called from interrupt context. But we call this in vibra_play() for
checking that the vibrator is not configured for audio mode.
The result is a "BUG: scheduling while atomic" if the first use of the
twl6040 is a vibra effect, because the first fetch is by reading the
twl6040 registers through (blocking) i2c and not from the cache.
As soon as the regmap has cached the status, further calls are fine.
The solution is to move the condition to the work() function which
runs in context that can block.
The original code returns -EBUSY, but the return value of ->play()
functions is ignored anyways. Hence, we do not loose functionality
by not returning an error but just reporting the issue to INFO loglevel.
Tested-on: Pyra (omap5) prototype
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For devm-managed input devices we should not modify input device's parent,
otherwise automatic release of resources will not work properly.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For devm-managed input devices we should not modify input device's parent,
otherwise automatic release of resources will not work properly.
Tested-by: "H. Nikolaus Schaller" <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Returning ret is wrong. And checking for an error as well. User space
may call multiple times until the work is really scheduled.
twl4030-vibra.c also ignores the return value.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
commit 21fb9f0d5e ("Input: twl6040-vibra - use system workqueue")
says that it switches to use the system workqueue but it did neither
- remove the workqueue struct variable
- replace code to really use the system workqueue
Instead it calls queue_work() on uninitialized info->workqueue.
The result is a NULL pointer dereference in vibra_play().
Solution: use schedule_work
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The trigger delay algorithm that converts from microseconds to
the register value looks incorrect. According to most of the PMIC
documentation, the equation is
delay (Seconds) = (1 / 1024) * 2 ^ (x + 4)
except for one case where the documentation looks to have a
formatting issue and the equation looks like
delay (Seconds) = (1 / 1024) * 2 x + 4
Most likely this driver was written with the improper
documentation to begin with. According to the downstream sources
the valid delays are from 2 seconds to 1/64 second, and the
latter equation just doesn't make sense for that. Let's fix the
algorithm and the range check to match the documentation and the
downstream sources.
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 92d57a73e4 ("input: Add support for Qualcomm PMIC8XXX power key")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We shouldn't assign the parent device of the input_dev to be the
parent MFD device, because this will be used for devres which causes
input_unregister_device to run after the haptics device has been
removed, since it is itself a child of the MFD device. The default
of using the haptics device itself as the parent is correct.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Linus Torvalds