Xbox One controllers have multiple interfaces which all have the
same class, subclass, and protocol. One of the these interfaces
has only a single endpoint. When Xpad attempts to bind to this
interface, it causes an oops when trying initialize the output URB
by trying to access the second endpoint's descriptor.
This situation was avoided for known Xbox One devices by checking
the XTYPE constant associated with the VID and PID tuple. However,
this breaks when new or previously unknown Xbox One controllers
are attached to the system.
This change addresses the problem by deriving the XTYPE for Xbox
One controllers based on the interface protocol before checking
the interface number.
Fixes: 1a48ff81b3 ("Input: xpad - add support for Xbox One controllers")
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Xbox One controllers that shipped with or were upgraded to the 2015
firmware discard the current rumble packets we send. This patch changes
the Xbox One rumble packet to a form that both the newer and older
firmware will accept.
It is based on changes made to support newer Xbox One controllers in
the SteamOS brewmaster-4.1 kernel branch.
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
added the according id and incresed XPAD_PKT_LEN to 64 as the elite
controller sends at least 33 byte messages [1].
Verified to be working by [2].
[1]: https://franticrain.github.io/sniffs/XboxOneSniff.html
[2]: https://github.com/paroj/xpad/issues/23
Signed-off-by: Pierre-Loup A. Griffais <eduke32@plagman.net>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
After initially connecting a wired Xbox 360 controller or sending it
a command to change LEDs, a status/response packet is interpreted as
controller input. This causes the state of buttons represented in
byte 2 of the controller data packet to be incorrect until the next
valid input packet. Wireless Xbox 360 controllers are not affected.
Writing a new value to the LED device while holding the Start button
and running jstest is sufficient to reproduce this bug. An event will
come through with the Start button released.
Xboxdrv also won't attempt to read controller input from a packet
where byte 0 is non-zero. It also checks that byte 1 is 0x14, but
that value differs between wired and wireless controllers and this
code is shared by both. I think just checking byte 0 is enough to
eliminate unwanted packets.
The following are some examples of 3-byte status packets I saw:
01 03 02
02 03 00
03 03 03
08 03 00
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds the VID/PID combination for the Xbox One version of the Mad
Catz FightStick TE 2.
The functionality that this provides is about on par with what the
Windows drivers for the stick manage to deliver.
What works:
- Digital stick
- 6 main buttons
- Xbox button
- The two buttons on the back
- The locking buttons (preventing accidental Xbox button press)
What doesn't work:
- Two of the main buttons (don't work on Windows either)
- The "Haptic" button setting does not have an effect (not sure if it
works on Windows)
I added the MAP_TRIGGERS_TO_BUTTONS option but in my (limited) testing
there was no practical difference with or without. The FightStick does
not have triggers though so adding it makes sense.
Signed-off-by: Silvan Jegen <s.jegen@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are two definitions of xpad_identify_controller(), one is used
when CONFIG_JOYSTICK_XPAD_LEDS is set, but the other one is empty
and never used, and we get a gcc warning about it:
drivers/input/joystick/xpad.c:1210:13: warning: 'xpad_identify_controller' defined but not used [-Wunused-function]
This removes the second definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: cae705baa4 ("Input: xpad - re-send LED command on present event")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Apparently the Covert Forces ID is not Covert Forces pad exclusive, but
rather denotes a new firmware version that can be found on all new
controllers and can be also updated on old hardware using Windows 10.
see: https://github.com/paroj/xpad/issues/19
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When lighting up the segment identifying wireless controller, Instead of
sending command directly to the controller, let's do it via LED API (usinf
led_set_brightness) so that LED object state is in sync with controller
state and we'll light up the correct segment on resume as well.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The irq_out urb is dead after suspend/ resume on my x360 wr pad. (also
reproduced by Zachary Lund [0]) Work around this by implementing
suspend, resume, and reset_resume callbacks and properly shutting down
URBs on suspend and restarting them on resume.
[0]: https://github.com/paroj/xpad/issues/6
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There's apparently a serial number woven into both input and output
packets; neglecting to specify a valid serial number causes the controller
to ignore the rumble packets.
The scale of the rumble was also apparently halved in the packets.
The initialization packet had to be changed to allow force feedback to
work.
see https://github.com/paroj/xpad/issues/7 for details.
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Track the status of the irq_out URB to prevent submission iof new requests
while current one is active. Failure to do so results in the "URB submitted
while active" warning/stack trace.
Store pending brightness and FF effect in the driver structure and replace
it with the latest requests until the device is ready to process next
request. Alternate serving LED vs FF requests to make sure one does not
starve another. See [1] for discussion. Inspired by patch of Sarah Bessmer
[2].
[1]: http://www.spinics.net/lists/linux-input/msg40708.html
[2]: http://www.spinics.net/lists/linux-input/msg31450.html
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Handle the "a new device is present" message properly by dynamically
creating the input device at this point in time. This means we now do not
"preallocate" all 4 devices when a single wireless base station is seen.
This requires a workqueue as we are in interrupt context when we learn
about this.
Also properly disconnect any devices that we are told are removed.
Signed-off-by: "Pierre-Loup A. Griffais" <pgriffais@valvesoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When powering up a wireless xbox 360 controller, some wrong joystick
events are generated. It is annoying because, for example, it makes
unwanted moves in Steam big picture mode's menu.
When my controller is powering up, this packet is received by the
driver:
00000000: 00 0f 00 f0 00 cc ff cf 8b e0 86 6a 68 f0 00 20 ...........jh..
00000010: 13 e3 20 1d 30 03 40 01 50 01 ff ff .. .0.@.P...
According to xboxdrv userspace driver source code, this packet is only
dumping a serial id and should not be interpreted as joystick events.
This issue can be easily seen with jstest:
$ jstest --event /dev/input/js0
This patch only adds a way to filter out this "serial" packet and as a
result it removes the spurous events.
Signed-off-by: Clement Calmels <clement.calmels@free.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Do not call xpad_identify_controller at init with wireless devices: it
conflicts with the already sent presence packet and will be called by
xpad360w_process_packet as needed anyway.
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When we initialize the driver/device, we really don't know how many
controllers are connected. So send a "query presence" command to the
base-station. (Command discovered by Zachary Lund)
Presence packet taken from:
https://github.com/computerquip/xpad5
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To allow us to later create / destroy the input device from the urb
callback, we need to initialize/ deinitialize the input device from a
separate function. So pull that logic out now to make later patches
more "obvious" as to what they do.
Signed-off-by: "Pierre-Loup A. Griffais" <pgriffais@valvesoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
as discussed here[0], x360w is the only pad that maps dpad_to_button.
This is bad for downstream developers as they have to differ between
x360 and x360w which is not intuitive.
This patch implements the suggested solution of exposing the dpad both
as axes and as buttons. This retains backward compatibility with software
already dealing with the difference while makes new software work as
expected across x360/ x360w pads.
[0] http://www.spinics.net/lists/linux-input/msg34421.html
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Move submission logic to a single point at the end of the function.
This makes it easy to add locking/ queuing code later on.
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This code was probably wrong ever since and is redundant with
xpad_send_led_command. Both try to send a similar command to the xbox360
controller. However xpad_send_led_command correctly uses the pad_nr instead
of bInterfaceNumber to select the led and re-uses the irq_out URB instead
of creating a new one.
Note that this change only affects the two supported wireless controllers.
Tested using the xbox360 wireless controller (PC).
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The pad_nr corresponds to the lit up LED on the controller. Therefore there
should be no gaps when enumerating. Currently a LED is only re-assigned
after a controller is re-connected 4 times.
This patch uses ida to track connected pads - this way we can re-assign
freed up pad number immediately.
Consider the following case:
1. pad A is connected and gets pad_nr = 0
2. pad B is connected and gets pad_nr = 1
3. pad A is disconnected
4. pad A is connected again
using ida_simple_get() controller A now correctly gets pad_nr = 0 again.
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rename led_no -> pad_nr: the number stored there is not the LED number - it
gets translated later on to a LED number in xpad_identify_controller;
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The "Razer Atrox Arcade Stick" features 10 buttons, and two of them (LT/RT)
don't work properly. Change its definition in xpad_device[] (mapping
field) to fix.
Signed-off-by: Dario Scarpa <dario.scarpa@duskzone.it>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is identical to the Xbox One controller but has a different product ID.
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The controller only receives commands when its present. So for the
correct LED to be lit the LED command has to be sent on the present
event.
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Based on Patch by Pierre-Loup A. Griffais <pgriffais@valvesoftware.com>:
Add the logic to set the LEDs on XBox Wireless controllers. Command
sequence found by sniffing the Windows data stream when plugging the
device in.
Updated based on comments on linux-input:
unify codepaths in xpad_send_led_command for wired/ wireless controller.
Also document command values for clarification.
All values tested on Xbox 360 Wireless Controller.
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds rumble support for Xbox One controller by sending continuous
rumble command. Trigger button rumbling is not yet implemented.
Signed-off-by: Ming-ting Yao Wei <mwei@lxde.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's initialize atomic_t variables keeping track of number of various
devices created so far with -1 in order to avoid extra subtraction
operation.
Signed-off-by: Aniroop Mathur <aniroop.mathur@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The xpad wireless endpoint is not a bulk endpoint on my devices, but
rather an interrupt one, so the USB core complains when it is submitted.
I'm guessing that the author really did mean that this should be an
interrupt urb, but as there are a zillion different xpad devices out
there, let's cover out bases and handle both bulk and interrupt
endpoints just as easily.
Signed-off-by: "Pierre-Loup A. Griffais" <pgriffais@valvesoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add Thrustmaster as Xbox 360 controller vendor. This is required for
example to make the GP XID (044f:b326) gamepad work.
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add the USB ID for the Xbox 360 Thrustmaster Ferrari 458 Racing Wheel.
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The userspace xboxdrv driver knows some more device ids than the kernel.
This patch adds the missing xbox gamepads from [1] to xpad.c
[1] https://github.com/Grumbel/xboxdrv/blob/master/src/xpad_device.cpp
Signed-off-by: Benjamin Valentin <benpicco@zedat.fu-berlin.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The xpad driver recognizes Razer Sabertooth controllers as generic xbox
controller, while it is really a 360 controller. This patch adds pid/vid
mappings for the controller so that it is correctly recognized.
Signed-off-by: Frank Razenberg <frank@zzattack.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Xbox One controllers require an initialization message to start sending
data, so xpad_init_output becomes a required function. The Xbox One
controller does not have LEDs like the Xbox 360 controller, so that
functionality is not implemented. The format of messages controlling rumble
is currently undocumented, so rumble support is not yet implemented.
Note that Xbox One controller advertises three interfaces with the same
interface class, subclass and protocol, so we have to also match against
interface number.
Signed-off-by: Ted Mielczarek <ted@mielczarek.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This enables the rumble force feedback on the F710 unit since
it is no longer treated as XTYPE_UNKNOWN type.
Signed-off-by: Petr Sebor <petr@scssoft.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When using Razer Onza controller the dpad doesn't work in many games
because D-PAD was mapped to buttons (useful for dance pads) and not to
HAT0X/Y axis.
ers who really want to have it mapped to buttons can restore previous
behavior by using 'dpad_to_buttons' module option.
Signed-off-by: Thomaz de Oliveira dos Reis <thor27@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Added MAP_TRIGGERS_TO_BUTTONS for Mad Catz Street Fighter IV FightPad
device. This controller model was already supported by the xpad
driver, but none of the buttons work correctly without this change.
Tested on kernel version 3.9.5.
Signed-off-by: Shawn Joseph <jms.576@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds VID/PID combinations for MadCatz, PDP and PowerA (new).
Removed Pelican 'TSZ' Wired Xbox 360 Controller since it's clashing with Edge
wireless Controller and I failed to confirm the PID.
Signed-off-by: "Guillermo A. Amaral B." <g@maral.me>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixed a few minor coding style issues in xpad driver.
Signed-off-by: "Guillermo A. Amaral B." <g@maral.me>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
I couldn't find the vendor ID in any of the online databases, but this
mat has a Pump It Up logo on the top side of the controller compartment,
and a disclaimer stating that Andamiro will not be liable on the bottom.
Signed-off-by: Yuri Khan <yurivkhan@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The device should be handled by xpad driver instead of generic HID driver.
Signed-off-by: Yuri Khan <yurivkhan@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: "Magnus Hörlin" <magnus@alefors.se>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: "Magnus Hörlin" <magnus@alefors.se>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cameron Gutman