The ADV748x has twelve 256-byte maps that can be accessed via the main
I2C ports. Each map has it own I2C address and acts as a standard slave
device on the I2C bus.
Allow a device tree node to override the default addresses so that
address conflicts with other devices on the same bus may be resolved at
the board description level.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV748x has 12 pages mapped onto I2C addresses.
In the existing implementation only 11 are mapped correctly in the page
enumerations, which causes an off-by-one fault on pages above the
infoframe definition due to a missing 'CBUS' page.
This causes the address for the CEC, SDP, TXA, and TXB to be incorrectly
programmed during the iterations in adv748x_initialise_clients().
Until now this has gone un-noticed due to the fact that following the
creation of the clients - the device is reset and the addresses are
reprogrammed in manually by the call to "adv748x_write_regs(state,
adv748x_set_slave_address);"
As part of moving to dynamic i2c address allocations repair this by
providing the missing CBUS page definition.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV748x has identical map configurations for each register map. The
duplication of each map can be simplified using a helper macro such that
each map is represented on a single line.
Define ADV748X_REGMAP_CONF for this purpose use it to create the tables.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The error handling for the adv748x_identify_chip() call erroneously
jumps to the err_cleanup_clients label before the clients have been
established.
Correct this by jumping to the next (and correct) label in the cleanup
code: err_cleanup_dt.
Fixes: 3e89586a64 ("media: i2c: adv748x: add adv748x driver")
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As of_node_full_name() now returns only the basename, the endpoint
information printed became useless:
adv748x 4-0070: Endpoint endpoint on port 7
adv748x 4-0070: Endpoint endpoint on port 8
adv748x 4-0070: Endpoint endpoint on port 10
adv748x 4-0070: Endpoint endpoint on port 11
Restore the old behavior by using "%pOF" instead:
adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@7/endpoint on port 7
adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@8/endpoint on port 8
adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@10/endpoint on port 10
adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@11/endpoint on port 11
Fixes: a7e4cfb0a7 ("of/fdt: only store the device node basename in full_name")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, and the driver is only exporting the OF ID
table entries as module aliases.
So if the driver is built as module, autoload won't work since udev/kmod
won't be able to match the registered OF device with its driver module.
Before this patch:
$ modinfo drivers/media/i2c/adv748x/adv748x.ko | grep alias
alias: of:N*T*Cadi,adv7482C*
alias: of:N*T*Cadi,adv7482
alias: of:N*T*Cadi,adv7481C*
alias: of:N*T*Cadi,adv7481
After this patch:
modinfo drivers/media/i2c/adv748x/adv748x.ko | grep alias
alias: of:N*T*Cadi,adv7482C*
alias: of:N*T*Cadi,adv7482
alias: of:N*T*Cadi,adv7481C*
alias: of:N*T*Cadi,adv7481
alias: i2c:adv7482
alias: i2c:adv7481
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Provide support for the ADV7481 and ADV7482.
The driver is modelled with 4 subdevices to allow simultaneous streaming
from the AFE (Analog front end) and HDMI inputs though two CSI TX
entities.
The HDMI entity is linked to the TXA CSI bus, whilst the AFE is linked
to the TXB CSI bus.
The driver is based on a prototype by Koji Matsuoka in the Renesas BSP,
and an earlier rework by Niklas Söderlund.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Kieran Bingham