This reverts commit 894116bd0e.
I applied the wrong version of this patch, correct
version coming up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently grabbed this report:
https://bugzilla.redhat.com/show_bug.cgi?id=1005567
Of an issue in which the bonding driver, with an attached vlan encountered the
following errors when bond0 was taken down and back up:
dummy1: promiscuity touches roof, set promiscuity failed. promiscuity feature of
device might be broken.
The error occurs because, during __bond_release_one, if we release our last
slave, we take on a random mac address and issue a NETDEV_CHANGEADDR
notification. With an attached vlan, the vlan may see that the vlan and bond
mac address were in sync, but no longer are. This triggers a call to dev_uc_add
and dev_set_rx_mode, which enables IFF_PROMISC on the bond device. Then, when
we complete __bond_release_one, we use the current state of the bond flags to
determine if we should decrement the promiscuity of the releasing slave. But
since the bond changed promiscuity state during the release operation, we
incorrectly decrement the slave promisc count when it wasn't in promiscuous mode
to begin with, causing the above error
Fix is pretty simple, just cache the bonding flags at the start of the function
and use those when determining the need to set promiscuity.
This is also needed for the ALLMULTI flag
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Mark Wu <wudxw@linux.vnet.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
Reported-by: Mark Wu <wudxw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TCP Small Queues was added, we used a sysctl to limit amount of
packets queues on Qdisc/device queues for a given TCP flow.
Problem is this limit is either too big for low rates, or too small
for high rates.
Now TCP stack has rate estimation in sk->sk_pacing_rate, and TSO
auto sizing, it can better control number of packets in Qdisc/device
queues.
New limit is two packets or at least 1 to 2 ms worth of packets.
Low rates flows benefit from this patch by having even smaller
number of packets in queues, allowing for faster recovery,
better RTT estimations.
High rates flows benefit from this patch by allowing more than 2 packets
in flight as we had reports this was a limiting factor to reach line
rate. [ In particular if TX completion is delayed because of coalescing
parameters ]
Example for a single flow on 10Gbp link controlled by FQ/pacing
14 packets in flight instead of 2
$ tc -s -d qd
qdisc fq 8001: dev eth0 root refcnt 32 limit 10000p flow_limit 100p
buckets 1024 quantum 3028 initial_quantum 15140
Sent 1168459366606 bytes 771822841 pkt (dropped 0, overlimits 0
requeues 6822476)
rate 9346Mbit 771713pps backlog 953820b 14p requeues 6822476
2047 flow, 2046 inactive, 1 throttled, delay 15673 ns
2372 gc, 0 highprio, 0 retrans, 9739249 throttled, 0 flows_plimit
Note that sk_pacing_rate is currently set to twice the actual rate, but
this might be refined in the future when a flow is in congestion
avoidance.
Additional change : skb->destructor should be set to tcp_wfree().
A future patch (for linux 3.13+) might remove tcp_limit_output_bytes
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass-all-multicast is controlled by bit 3 in RX control, not bit 2
(pass undersized frames).
Reported-by: Joseph Chang <joseph_chang@davicom.com.tw>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fq_reset() should drops all packets in queue, including
throttled flows.
This patch moves code from fq_destroy() to fq_reset()
to do the cleaning.
fq_change() must stop calling fq_dequeue() if all remaining
packets are from throttled flows.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 8ed781668d ("flow_keys: include thoff into flow_keys for
later usage"), we missed that existing code was using nhoff as a
temporary variable that could not always contain transport header
offset.
This is not a problem for TCP/UDP because port offset (@poff)
is 0 for these protocols.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the frontend state changes netback now specifies its desired state to
a new function, set_backend_state(), which transitions through any
necessary intermediate states.
This fixes an issue observed with some old Windows frontend drivers where
they failed to transition through the Closing state and netback would not
behave correctly.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the scenario where an IPv6 router is advertising a fixed
preferred_lft of 1800 seconds, while the valid_lft begins at 3600
seconds and counts down in realtime.
A client should reset its preferred_lft to 1800 every time the RA is
received, but a bug is causing Linux to ignore the update.
The core problem is here:
if (prefered_lft != ifp->prefered_lft) {
Note that ifp->prefered_lft is an offset, so it doesn't decrease over
time. Thus, the comparison is always (1800 != 1800), which fails to
trigger an update.
The most direct solution would be to compute a "stored_prefered_lft",
and use that value in the comparison. But I think that trying to filter
out unnecessary updates here is a premature optimization. In order for
the filter to apply, both of these would need to hold:
- The advertised valid_lft and preferred_lft are both declining in
real time.
- No clock skew exists between the router & client.
So in this patch, I've set "update_lft = 1" unconditionally, which
allows the surrounding code to be greatly simplified.
Signed-off-by: Paul Marks <pmarks@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While sending packet skb_cow_head() can change skb header which
invalidates inner_iph pointer to skb header. Following patch
avoid using it. Found by code inspection.
This bug was introduced by commit 0e6fbc5b6c (ip_tunnels: extend
iptunnel_xmit()).
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cinterion PLXX LTE devices have a 0x0060 product ID, not 0x12d1.
The blacklisting in the serial/option driver does actually use the correct PID,
as per commit 8ff10bdb14 ('USB: Blacklisted
Cinterion's PLxx WWAN Interface').
CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
Signed-off-by: Aleksander Morgado <aleksander@lanedo.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Christian Schmiedl <christian.schmiedl@gemalto.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently IEEE 1588 timer reference clock source is determined through
hard-coded value in gianfar_ptp driver. This patch allows to select ptp
clock source by means of device tree file node.
For instance:
fsl,cksel = <0>;
for using external (TSEC_TMR_CLK input) high precision timer
reference clock.
Other acceptable values:
<1> : eTSEC system clock
<2> : eTSEC1 transmit clock
<3> : RTC clock input
When this attribute isn't used, eTSEC system clock will serve as
IEEE 1588 timer reference clock.
Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of RCU api makes vxlan code easier to understand. It also
fixes bug due to missing ACCESS_ONCE() on sk_user_data dereference.
In rare case without ACCESS_ONCE() compiler might omit vs on
sk_user_data dereference.
Compiler can use vs as alias for sk->sk_user_data, resulting in
multiple sk_user_data dereference in rcu read context which
could change.
CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A host might need net_secret[] and never open a single socket.
Problem added in commit aebda156a5
("net: defer net_secret[] initialization")
Based on prior patch from Hannes Frederic Sowa.
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@strressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is currently serialization network namespaces exiting and
network devices exiting as the final part of netdev_run_todo does not
happen under the rtnl_lock. This is compounded by the fact that the
only list of devices unregistering in netdev_run_todo is local to the
netdev_run_todo.
This lack of serialization in extreme cases results in network devices
unregistering in netdev_run_todo after the loopback device of their
network namespace has been freed (making dst_ifdown unsafe), and after
the their network namespace has exited (making the NETDEV_UNREGISTER,
and NETDEV_UNREGISTER_FINAL callbacks unsafe).
Add the missing serialization by a per network namespace count of how
many network devices are unregistering and having a wait queue that is
woken up whenever the count is decreased. The count and wait queue
allow default_device_exit_batch to wait until all of the unregistration
activity for a network namespace has finished before proceeding to
unregister the loopback device and then allowing the network namespace
to exit.
Only a single global wait queue is used because there is a single global
lock, and there is a single waiter, per network namespace wait queues
would be a waste of resources.
The per network namespace count of unregistering devices gives a
progress guarantee because the number of network devices unregistering
in an exiting network namespace must ultimately drop to zero (assuming
network device unregistration completes).
The basic logic remains the same as in v1. This patch is now half
comment and half rtnl_lock_unregistering an expanded version of
wait_event performs no extra work in the common case where no network
devices are unregistering when we get to default_device_exit_batch.
Reported-by: Francesco Ruggeri <fruggeri@aristanetworks.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a router is doing DNAT for 6to4/6rd packets the latest
anti-spoofing commit 218774dc ("ipv6: add anti-spoofing checks for
6to4 and 6rd") will drop them because the IPv6 address embedded does
not match the IPv4 destination. This patch will allow them to pass by
testing if we have an address that matches on 6to4/6rd interface. I
have been hit by this problem using Fedora and IPV6TO4_IPV4ADDR.
Also, log the dropped packets (with rate limit).
Signed-off-by: Catalin(ux) M. BOIE <catab@embedromix.ro>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 638c5115a7949(USBNET: support DMA SG) introduces DMA SG
if the usb host controller is capable of building packet from
discontinuous buffers, but missed handling padding packet when
building DMA SG.
This patch attachs the pre-allocated padding packet at the
end of the sg list, so padding packet can be sent to device
if drivers require that.
Reported-by: David Laight <David.Laight@aculab.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Commit 7e2cf4feba
("qlcnic: change driver hardware interface mechanism")
has overwritten
commit b43e5ee76a
("qlcnic: Register device in FAILED state")
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN priority is not being displayed for a VF currently when user executes
"ip link show" command. This patch fixes it.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thix fix allows the VLAN priority to be configured for a VF interface
via the "ip link set DEVICE vf NUM" path.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the VF interfaces have privilege to add VLANs.
Allow VLANs to be configured on these interfaces.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In BE3-R, when UMC is enabled, the number of VLANs that can be added
to the interface is reduced to 15.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the interface runs out of the allocated entries in VLAN table,
we program the interface in VLAN promiscuous mode.
Use OPCODE_COMMON_NTWK_RX_FILTER to set VLAN Promiscuous mode
instead of OPCODE_COMMON_NTWK_VLAN_CONFIG.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Size of be_nic_res_desc structure is incorrect. Fix it.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx on SH-R can lockup if the packet size is less than 32 bytes.
Pad such packets to a safer 36-byte size.
Patch uses the Lancer-R workaround - which checks for packet <= 32-bytes
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Regarding the Bluetooth bits, Gustavo says:
"First Bluetooth fixes to 3.12, it includes:
* 3 patches to add device id for 3 new hardwares.
* 2 patches from Johan to fix the rfkill behaviour during setup stage
* a small clean up in the rfcomm TTY code that fixes a potential racy
condition (by Gianluca Anzolin)
* 2 fixes to proper set encryption key size and security level in the
peripheral role of Bluetooth LE devices. (by Andre Guedes)
* a fix for dealing devices where pairing is not necessary, we were keeping
the Bluetooth ACL connection alive for too much time. (by Syam Sidhardhan)"
Also, I fixed-up an curly-brace indentation problem in the Bluetooth
code while merging. On top of that...
Alexey Khoroshilov brings a p54usb fix to avoid a resource leak when
request_firmware_nowait fails.
Amitkumar Karwar fixes a firmware hang caused by too much header data
being appended for USB devices using the mwifiex driver.
Arend van Spriel provides three fixes: a brcmfmac fix to relocate some
driver code outside of an .init section; a scheduling while atomic
fix for bcma; and, another scheduling while atomic fix for brcmsmac.
Bing Zhao offers a pair of mwifiex fixes: a code change to avoid
firmware timeouts on USB; and a fix for a NULL pointer dereference.
Christian Lamparter adds a device ID to p54usb.
Felix Fietkau implements a quartet of small ath9k fixes, including
a locking fix, a list management fix, a fix to properly mark a stale
buffer, and an aggregate buffering fix.
Larry Finger champions a data alignment fix to make rtlwifi work
better with ARM builds.
Solomon Peachy reverts an earlier interrupt handling fix for cw1200
and replaces it with a new threaded oneshot irq handler implementation.
Sujith Manoharan fixes an ath9k regression by reverting an earlier
patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to igb and i40e.
Todd provides a fix for 82580 devices in igb, where the ethtool
loopback test was missing 82580 copper devices.
Jesse provides five fixes/cleanups to i40e based on feedback from
Joe Perches and the community.
v2: fixed up patch 5 in the series based on feedback from Joe Perches
and David Miller
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
coccicheck shows:
drivers/net/ethernet/intel/i40e/i40e_adminq.c:704:2-8: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_adminq.c:763:1-7: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_adminq.c:810:2-8: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_common.c:510:2-8: Replace memcpy
with struct assignment
Fix each of them with a *a = *b;
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As mentioned by Joe Perches, clean up return values in some functions
making sure to have consistent return types, not mixing types.
A couple of Joe's comments suggested returning void, but since
the functions in question are ndo defined, the return values are fixed.
So make a comment in the header that notes this is a function called by
net_device_ops.
v2: fix post increment bug in return
CC: Joe Perches <joe@perches.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When calling admin queue functions the driver should use aq_ret
variable to help make clear that the return value is not a regular
return variable.
This allows for clean up of the return types that were previously
converted to int.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As mentioned by Joe Perches clean up a loop flow.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joe Perches <joe@perches.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As mentioned by Joe Perches, we should be using
foo = alloc(...)
if (!foo)
return -ENOMEM;
return 0;
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joe Perches <joe@perches.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add back 82580 loopback tests to ethtool.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Outgoing packets sent by via-rhine have their VLAN PCP field off by one
(when hardware acceleration is enabled). The TX descriptor expects only VID
and PCP (without a CFI/DEI bit).
Peter Boström noticed and reported the bug.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Cc: Peter Boström <peter.bostrom@netrounds.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses platform_driver_probe() to obtain platform data
if any. However, that function is placed in the .init section so
it must be called upon driver module initialization.
The problem was reported by Fenguang Wu resulting in a kernel
oops because the .init section was already freed.
[ 48.966342] Switched to clocksource tsc
[ 48.970002] kernel tried to execute NX-protected page - exploit attempt? (uid: 0)
[ 48.970851] BUG: unable to handle kernel paging request at ffffffff82196446
[ 48.970957] IP: [<ffffffff82196446>] classes_init+0x26/0x26
[ 48.970957] PGD 1e76067 PUD 1e77063 PMD f388063 PTE 8000000002196163
[ 48.970957] Oops: 0011 [#1]
[ 48.970957] CPU: 0 PID: 17 Comm: kworker/0:1 Not tainted 3.11.0-rc7-00444-gc52dd7f #23
[ 48.970957] Workqueue: events brcmf_driver_init
[ 48.970957] task: ffff8800001d2000 ti: ffff8800001d4000 task.ti: ffff8800001d4000
[ 48.970957] RIP: 0010:[<ffffffff82196446>] [<ffffffff82196446>] classes_init+0x26/0x26
[ 48.970957] RSP: 0000:ffff8800001d5d40 EFLAGS: 00000286
[ 48.970957] RAX: 0000000000000001 RBX: ffffffff820c5620 RCX: 0000000000000000
[ 48.970957] RDX: 0000000000000001 RSI: ffffffff816f7380 RDI: ffffffff820c56c0
[ 48.970957] RBP: ffff8800001d5d50 R08: ffff8800001d2508 R09: 0000000000000002
[ 48.970957] R10: 0000000000000000 R11: 0001f7ce298c5620 R12: ffff8800001c76b0
[ 48.970957] R13: ffffffff81e91d40 R14: 0000000000000000 R15: ffff88000e0ce300
[ 48.970957] FS: 0000000000000000(0000) GS:ffffffff81e84000(0000) knlGS:0000000000000000
[ 48.970957] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 48.970957] CR2: ffffffff82196446 CR3: 0000000001e75000 CR4: 00000000000006b0
[ 48.970957] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 48.970957] DR3: 0000000000000000 DR6: 0000000000000000 DR7: 0000000000000000
[ 48.970957] Stack:
[ 48.970957] ffffffff816f7df8 ffffffff820c5620 ffff8800001d5d60 ffffffff816eeec9
[ 48.970957] ffff8800001d5de0 ffffffff81073dc5 ffffffff81073d68 ffff8800001d5db8
[ 48.970957] 0000000000000086 ffffffff820c5620 ffffffff824f7fd0 0000000000000000
[ 48.970957] Call Trace:
[ 48.970957] [<ffffffff816f7df8>] ? brcmf_sdio_init+0x18/0x70
[ 48.970957] [<ffffffff816eeec9>] brcmf_driver_init+0x9/0x10
[ 48.970957] [<ffffffff81073dc5>] process_one_work+0x1d5/0x480
[ 48.970957] [<ffffffff81073d68>] ? process_one_work+0x178/0x480
[ 48.970957] [<ffffffff81074188>] worker_thread+0x118/0x3a0
[ 48.970957] [<ffffffff81074070>] ? process_one_work+0x480/0x480
[ 48.970957] [<ffffffff8107aa17>] kthread+0xe7/0xf0
[ 48.970957] [<ffffffff810829f7>] ? finish_task_switch.constprop.57+0x37/0xd0
[ 48.970957] [<ffffffff8107a930>] ? __kthread_parkme+0x80/0x80
[ 48.970957] [<ffffffff81a6923a>] ret_from_fork+0x7a/0xb0
[ 48.970957] [<ffffffff8107a930>] ? __kthread_parkme+0x80/0x80
[ 48.970957] Code: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
cc cc cc cc cc cc <cc> cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
[ 48.970957] RIP [<ffffffff82196446>] classes_init+0x26/0x26
[ 48.970957] RSP <ffff8800001d5d40>
[ 48.970957] CR2: ffffffff82196446
[ 48.970957] ---[ end trace 62980817cd525f14 ]---
Cc: <stable@vger.kernel.org> # 3.10.x, 3.11.x
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bug 60815 - Interface hangs in mwifiex_usb
https://bugzilla.kernel.org/show_bug.cgi?id=60815
[ 2.883807] BUG: unable to handle kernel NULL pointer dereference
at 0000000000000048
[ 2.883813] IP: [<ffffffff815a65e0>] pfifo_fast_enqueue+0x90/0x90
[ 2.883834] CPU: 1 PID: 3220 Comm: kworker/u8:90 Not tainted
3.11.1-monotone-l0 #6
[ 2.883834] Hardware name: Microsoft Corporation Surface with
Windows 8 Pro/Surface with Windows 8 Pro,
BIOS 1.03.0450 03/29/2013
On Surface Pro, suspend to ram gives a NULL pointer dereference in
pfifo_fast_enqueue(). The stack trace reveals that the offending
call is clearing carrier in mwifiex_usb suspend handler.
Since commit 1499d9f "mwifiex: don't drop carrier flag over suspend"
has removed the carrier flag handling over suspend/resume in SDIO
and PCIe drivers, I'm removing it in USB driver too. This also fixes
the bug for Surface Pro.
Cc: <stable@vger.kernel.org> # 3.5+
Tested-by: Dmitry Khromov <icechrome@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bug 60815 - Interface hangs in mwifiex_usb
https://bugzilla.kernel.org/show_bug.cgi?id=60815
We have 4 bytes of interface header for packets delivered to SDIO
and PCIe, but not for USB interface.
In Tx AMSDU case, currently 4 bytes of garbage data is unnecessarily
appended for USB packets. This sometimes leads to a firmware hang,
because it may not interpret the data packet correctly.
Problem is fixed by removing this redundant headroom for USB.
Cc: <stable@vger.kernel.org> # 3.5+
Tested-by: Dmitry Khromov <icechrome@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added USB ID for Corega WLUSB2GTST USB adapter.
Cc: <stable@vger.kernel.org>
Reported-by: Joerg Kalisch <the_force@gmx.de>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This supercedes the older patch ("cw1200: Don't perform SPI transfers in
interrupt context") that badly attempted to fix this problem.
This is a far simpler solution, which has the added benefit of
actually working.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit aec8e88c94.
This solution turned out to cause interrupt delivery problems, and
rather than trying to fix this approach, it has been scrapped in favor
of an alternative (and far simpler) implementation.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For pcie8897, the hs_cfg cancel command (0xe5) times out when host
comes out of suspend. This is caused by an incompleted host sleep
handshake between driver and firmware.
Like SDIO interface, PCIe also needs to go through firmware power
save events to complete the handshake for host sleep configuration.
Only USB interface doesn't require power save events for hs_cfg.
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The private array at the end of the rtl_priv struct is not aligned.
On ARM architecture, this causes an alignment trap and is fixed by aligning
that array with __align(sizeof(void *)). That should properly align that
space according to the requirements of all architectures.
Reported-by: Jason Andrews <jasona@cadence.com>
Tested-by: Jason Andrews <jasona@cadence.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prevents race conditions when un-aggregated frames are pending in the
driver.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If request_firmware_nowait() fails in p54u_load_firmware(),
p54u_load_firmware_cb is not called and no one decrements usb_dev refcnt.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When .release_buffered_frames was implemented, only A-MPDU packets were
buffered internally. Now that this has changed, the BUF_AMPDU flag needs
to be checked before calling ath_tx_addto_baw
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Optimize LNA check" tried
to use the "rs_firstaggr" flag to optimize the LNA
combining algorithm when processing subframes in
an A-MPDU. This doesn't appear to work well in practice,
so revert it and use the old method of relying on
"rs_moreaggr".
Cc: stable@vger.kernel.org # 3.11
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
David S. Miller