When Qav mode is enabled, queue 0 should be kept on Stream Reservation
mode. From the i210 datasheet, section 8.12.19:
"Note: Queue0 QueueMode must be set to 1b when TransmitMode is set to
Qav." ("QueueMode 1b" represents the Stream Reservation mode)
The solution is to give queue 0 the all the credits it might need, so
it has priority over queue 1.
A situation where this can happen is when cbs is "installed" only on
queue 1, leaving queue 0 alone. For example:
$ tc qdisc replace dev enp2s0 handle 100: parent root mqprio num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 0
$ tc qdisc replace dev enp2s0 parent 100:2 cbs locredit -1470 \
hicredit 30 sendslope -980000 idleslope 20000 offload 1
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current error handling for failed resource setup for xdp_ring
data is a break out of the loop and returning 0 indicated everything
was OK, when in fact it is not. Fix this by exiting via the
error exit label err_setup_tx that will clean up the resources
correctly and return and error status.
Detected by CoverityScan, CID#1466879 ("Logically dead code")
Fixes: 21092e9ce8 ("ixgbevf: Add support for XDP_TX action")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for adaptive TX moderation. This greatly reduces TX interrupt
rate and increases bandwidth, mostly for TCP bandwidth over ARM
architecture (below). There is a slight single stream TCP with very large
message sizes degradation (x86). In this case if there's any moderation on
transmitted packets the bandwidth would reduce due to hitting TCP output limit.
Since this is a synthetic case, this is still worth doing.
Performance improvement (ConnectX-4Lx 40GbE, ARM)
TCP 64B bandwidth with 1-50 streams increased 6-35%.
TCP 64B bandwidth with 100-500 streams increased 20-70%.
Performance improvement (ConnectX-5 100GbE, x86)
Bandwidth: increased up to 40% (1024B with 10s of streams).
Interrupt rate: reduced up to 50% (1024B with 1000s of streams).
Performance degradation (ConnectX-5 100GbE, x86)
Bandwidth: up to 10% decrease single stream TCP (1MB message size from
51Gb/s to 47Gb/s).
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparation for introducing adaptive TX to net DIM.
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same fix in Commit dbe173079a ("bridge: fix netconsole
setup over bridge") is also needed for team driver.
While at it, remove the unnecessary parameter *team from
team_port_enable_netpoll().
v1->v2:
- fix it in a better way, as does bridge.
Fixes: 0fb52a27a0 ("team: cleanup netpoll clode")
Reported-by: João Avelino Bellomo Filho <jbellomo@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SFP eeprom indicates the transceiver signals (Rx LOS, Tx Fault, etc.)
that it supports. Update the driver to include checking the eeprom data
when deciding whether to use a transceiver signal.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update xgbe-phy-v2.c to make use of the auto-negotiation (AN) phy hooks
to improve the ability to successfully complete Clause 73 AN when running
at 10gbps. Hardware can sometimes have issues with CDR lock when the
AN DME page exchange is being performed.
The AN and KR training hooks are used as follows:
- The pre AN hook is used to disable CDR tracking in the PHY so that the
DME page exchange can be successfully and consistently completed.
- The post KR training hook is used to re-enable the CDR tracking so that
KR training can successfully complete.
- The post AN hook is used to check for an unsuccessful AN which will
increase a CDR tracking enablement delay (up to a maximum value).
Add two debugfs entries to allow control over use of the CDR tracking
workaround. The debugfs entries allow the CDR tracking workaround to
be disabled and determine whether to re-enable CDR tracking before or
after link training has been initiated.
Also, with these changes the receiver reset cycle that is performed during
the link status check can be performed less often.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hooks to the driver auto-negotiation (AN) flow to allow the different
phy implementations to perform any steps necessary to improve AN.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must validate sockaddr_len, otherwise userspace can pass fewer data
than we expect and we end up accessing invalid data.
Fixes: 224cf5ad14 ("ppp: Move the PPP drivers")
Reported-by: syzbot+4f03bdf92fdf9ef5ddab@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
If WOL event happened once, the LED[2] interrupt pin will not be
cleared unless we read the CSISR register. If interrupts are in use,
the normal interrupt handling will clear the WOL event. Let's clear the
WOL event before enabling it if !phy_interrupt_is_valid().
Signed-off-by: Jingju Hou <Jingju.Hou@synaptics.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuration information is added to the debug data collection, in
addition to register dump.
Added qed_dbg_nvm_image() that receives an image type, allocates a
buffer and reads the image. The images are saved in the buffers and the
dump size is updated.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since nvm images attributes are cached during driver load, acquiring ptt
is not needed when calling qed_mcp_get_nvm_image().
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all the core version detection to a common place ("hwif.c") and
implement a table which can be used to lookup the correct callbacks for
each IP version.
This simplifies the initialization flow of each IP version and eases
future implementation of new IP versions.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no benefit in using netif_info et al before the net_device has
been registered. We get messages like
r8169 0000:03:00.0 (unnamed net_device) (uninitialized): [message]
Therefore use dev_info/dev_err instead.
As a side effect we don't need parameter dev for function
rtl8169_get_mac_version() any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After Commit 8a8efa22f5 ("bonding: sync netpoll code with bridge"), it
would set slave_dev npinfo in slave_enable_netpoll when enslaving a dev
if bond->dev->npinfo was set.
However now slave_dev npinfo is set with bond->dev->npinfo before calling
slave_enable_netpoll. With slave_dev npinfo set, __netpoll_setup called
in slave_enable_netpoll will not call slave dev's .ndo_netpoll_setup().
It causes that the lower dev of this slave dev can't set its npinfo.
One way to reproduce it:
# modprobe bonding
# brctl addbr br0
# brctl addif br0 eth1
# ifconfig bond0 192.168.122.1/24 up
# ifenslave bond0 eth2
# systemctl restart netconsole
# ifenslave bond0 br0
# ifconfig eth2 down
# systemctl restart netconsole
The netpoll won't really work.
This patch is to remove that slave_dev npinfo setting in bond_enslave().
Fixes: 8a8efa22f5 ("bonding: sync netpoll code with bridge")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 6870de435b ("bpf: make virtio compatible w/
bpf_xdp_adjust_tail") i didn't account for vi->hdr_len during new
packet's length calculation after bpf_prog_run in receive_mergeable.
because of this all packets, if they were passed to the kernel,
were truncated by 12 bytes.
Fixes:6870de435b90 ("bpf: make virtio compatible w/ bpf_xdp_adjust_tail")
Reported-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Nikita V. Shirokov <tehnerd@tehnerd.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Avoid using value stored in the login response buffer when
cleaning TX and RX buffer pools since these could be inconsistent
depending on the device state. Instead use the field in the driver's
private data that tracks the number of active pools.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conversion of rndis friendly name to utf8 uses a standard
kernel routine which is optional in config. Therefore build
would fail for some configurations. Resolve by selecting needed
library.
Fixes: 0fe554a46a ("hv_netvsc: propogate Hyper-V friendly name into interface alias")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPDMA_TX_PRIORITY_MAP in real is vlan pcp field priority mapping
register and basically replaces vlan pcp field for tagged packets.
So, set it to be 1:1 mapping. Otherwise, it will cause unexpected
change of egress vlan tagged packets, like prio 2 -> prio 5.
Fixes: e05107e6b7 ("net: ethernet: ti: cpsw: add multi queue support")
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-04-21
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Initial work on BPF Type Format (BTF) is added, which is a meta
data format which describes the data types of BPF programs / maps.
BTF has its roots from CTF (Compact C-Type format) with a number
of changes to it. First use case is to provide a generic pretty
print capability for BPF maps inspection, later work will also
add BTF to bpftool. pahole support to convert dwarf to BTF will
be upstreamed as well (https://github.com/iamkafai/pahole/tree/btf),
from Martin.
2) Add a new xdp_bpf_adjust_tail() BPF helper for XDP that allows
for changing the data_end pointer. Only shrinking is currently
supported which helps for crafting ICMP control messages. Minor
changes in drivers have been added where needed so they recalc
the packet's length also when data_end was adjusted, from Nikita.
3) Improve bpftool to make it easier to feed hex bytes via cmdline
for map operations, from Quentin.
4) Add support for various missing BPF prog types and attach types
that have been added to kernel recently but neither to bpftool
nor libbpf yet. Doc and bash completion updates have been added
as well for bpftool, from Andrey.
5) Proper fix for avoiding to leak info stored in frame data on page
reuse for the two bpf_xdp_adjust_{head,meta} helpers by disallowing
to move the pointers into struct xdp_frame area, from Jesper.
6) Follow-up compile fix from BTF in order to include stdbool.h in
libbpf, from Björn.
7) Few fixes in BPF sample code, that is, a typo on the netdevice
in a comment and fixup proper dump of XDP action code in the
tracepoint exception, from Wang and Jesper.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the tun driver, in absence of an eBPF steering program,
always compute the rxhash in its rx path, even when such value
is later unused due to additional checks (
This changeset moves the all the related checks just before the
__skb_get_hash_symmetric(), so that the latter is no more computed
when unneeded.
Also replace an unneeded RCU section with rcu_access_pointer().
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to dump lan78xx family registers using ethtool, add
support at lan78xx driver level.
Signed-off-by: Raghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for DT property "microchip,led-modes", a vector of zero
to four cells (u32s) in the range 0-15, each of which sets the mode
for one of the LEDs. Some possible values are:
0=link/activity 1=link1000/activity
2=link100/activity 3=link10/activity
4=link100/1000/activity 5=link10/1000/activity
6=link10/100/activity 14=off 15=on
These values are given symbolic constants in a dt-bindings header.
Also use the presence of the DT property to indicate that the
LEDs should be enabled - necessary in the event that no valid OTP
or EEPROM is available.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a standard mechanism for locating and using a MAC address from
the Device Tree. Use this facility in the lan78xx driver to support
applications without programmed EEPROM or OTP. At the same time,
regularise the handling of the different address sources.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cpumask_local_spread to provide interrupt affinity hints
for each queue. This will spread interrupts across NUMA local
CPUs first, extending to remote nodes if needed.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There may be a need for VF driver to request PF to explicitly update its
bulletin with a MAC address.
e.g. When user assigns a MAC address to VF while VF is still down,
and PF's bulletin board contains different MAC address, in this case,
when VF's interface is brought up, it gets loaded with MAC address from
bulletin board which is not desirable.
To handle this corner case, we need a new TLV to request PF to update
its bulletin board with suggested MAC.
This request will be honored only for trusted VFs.
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per existing behavior, when PF sets a MAC address for a VF
(also called as forced MAC), VF is not allowed to change its
MAC address afterwards.
This puts the limitation on few use cases such as bonding of VFs,
where bonding driver asks VF to change its MAC address.
This patch uses a VF trust mode to allow VF to change its MAC address
in spite PF has set a forced MAC for that VF.
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, on a new link creation or when 'remote' address parameter
is updated, an MTU is not changed and always equals 1500. When a lower
device has a larger MTU, it might not be efficient, e.g. for UDP, and
requires the manual MTU adjustments to match the MTU of the lower
device.
This patch tries to automate this process, finds a lower device using
the 'remote' address parameter, then uses its MTU to tune GENEVE's MTU:
* on a new link creation
* when 'remote' parameter is changed
Also with this patch, the MTU from a user, on a new link creation, is
passed to geneve_change_mtu() where it is verified, and MTU adjustments
with a lower device is skipped in that case. Prior that change, it was
possible to set the invalid MTU values on a new link creation.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
geneve_change_mtu() will be used not only as ndo_change_mtu() callback,
but also to verify a user specified MTU on a new link creation in the
next patch.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ETH_HLEN instead and introduce two new macros: GENEVE_IPV4_HLEN
and GENEVE_IPV6_HLEN that include Ethernet header length, corresponded
IP header length and GENEVE_BASE_HLEN.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Account for operational state when determining port linkup state,
as per Documentation/networking/operstates.txt.
Signed-off-by: George Wilkie <gwilkie@vyatta.att-mail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added the ndo to gather VF statistics through the PF.
Collect VF statistics via mailbox from VF.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for specifying system controller that configures
phy-mode setting.
According to the DT property "phy-mode", it's necessary to configure the
controller, which is used to choose the settings of the MAC suitable,
for example, mdio pin connections, internal clocks, and so on.
Supported phy-modes are SoC-dependent. The driver allows phy-mode to set
"internal" if the SoC has a built-in PHY, and {"mii", "rmii", "rgmii"}
if the SoC supports each mode. So we have to check whether the phy-mode
is valid or not.
This adds the following features for each SoC:
- check whether the SoC supports the specified phy-mode
- configure the controller accroding to phy-mode
The DT property accepts one argument to distinguish them for multiple MAC
instances.
ethernet@65000000 {
...
socionext,syscon-phy-mode = <&soc_glue 0>;
};
ethernet@65200000 {
...
socionext,syscon-phy-mode = <&soc_glue 1>;
};
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the link is becoming up for Pro4 SoC, the kernel is stalled
due to some missing clocks and resets.
The AVE block for Pro4 is connected to the GIO bus in the SoC.
Without its clock/reset, the access to the AVE register makes the
system stall.
In the same way, another MAC clock for Giga-bit Connection and
the PHY clock are also required for Pro4 to activate the Giga-bit feature
and to recognize the PHY.
To satisfy these requirements, this patch adds support for multiple clocks
and resets, and adds the clock-names and reset-names to the binding because
we need to distinguish clock/reset for the AVE main block and the others.
Also, make the resets a required property. Currently, "reset is
optional" relies on that the bootloader or firmware has deasserted
the reset before booting the kernel. Drivers should work without
such expectation.
Fixes: 4c270b55a5 ("net: ethernet: socionext: add AVE ethernet driver")
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdiobus_register will search for any mdiobus board info registered for
the bus being registered. If found, it will probe devices on the bus.
That device, if for example it is an ethernet switch, may then try to
register an mdio bus. Thus we need to allow recursive calls to
mdiobus_register.
Holding the mdio_board_lock will cause a deadlock during this
recursion. Release the lock and use list_for_each_entry_safe.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some firmware images, the length of BNX_DIR_TYPE_PKG_LOG nvram type
could be greater than the fixed buffer length of 4096 bytes allocated by
the driver. This was causing HWRM_NVM_READ to copy more data to the buffer
than the allocated size, causing general protection fault.
Fix the issue by allocating the exact buffer length returned by
HWRM_NVM_FIND_DIR_ENTRY, instead of 4096. Move the kzalloc() call
into the bnxt_get_pkgver() function.
Fixes: 3ebf6f0a09 ("bnxt_en: Add installed-package firmware version reporting via Ethtool GDRVINFO")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
offloads is a buffer in virtio format, should use
the __virtio64 tag.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Programming vids (adding or removing them) still passes
guest-endian values in the DMA buffer. That's wrong
if guest is big-endian and when virtio 1 is enabled.
Note: this is on top of a previous patch:
virtio_net: split out ctrl buffer
Fixes: 9465a7a6f ("virtio_net: enable v1.0 support")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending control commands, virtio net sets up several buffers for
DMA. The buffers are all part of the net device which means it's
actually allocated by kvmalloc so it's in theory (on extreme memory
pressure) possible to get a vmalloc'ed buffer which on some platforms
means we can't DMA there.
Fix up by moving the DMA buffers into a separate structure.
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When longer interface names are used, the action names exposed in
/proc/interrupts and /proc/irq/* maybe truncated. For example, when
using the predictable name algorithm in systemd on a HiSilicon D05,
I see:
ubuntu@d05-3:~$ grep enahisic2i0-tx /proc/interrupts | sed 's/.* //'
enahisic2i0-tx0
enahisic2i0-tx1
[...]
enahisic2i0-tx8
enahisic2i0-tx9
enahisic2i0-tx1
enahisic2i0-tx1
enahisic2i0-tx1
enahisic2i0-tx1
enahisic2i0-tx1
enahisic2i0-tx1
Increase the max ring name length to allow for an interface name
of IFNAMSIZE. After this change, I now see:
$ grep enahisic2i0-tx /proc/interrupts | sed 's/.* //'
enahisic2i0-tx0
enahisic2i0-tx1
enahisic2i0-tx2
[...]
enahisic2i0-tx8
enahisic2i0-tx9
enahisic2i0-tx10
enahisic2i0-tx11
enahisic2i0-tx12
enahisic2i0-tx13
enahisic2i0-tx14
enahisic2i0-tx15
Signed-off-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add platform device driver to populate the ax88796 platform data from
information provided by the XSurf100 zorro device driver. The ax88796
module will be loaded through this module's probe function.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The net device struct pointer is stored as platform device drvdata on
module probe - clear the drvdata entry on probe fail there, as well as
when unloading the module.
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the Amiga X-Surf100, the network card interrupt is shared with many
other interrupt sources, so requires the IRQF_SHARED flag to register.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able to tell the ax88796 driver whether it is sensible to enter
the 8390 interrupt handler, an "is this interrupt caused by the 88796"
callback has been added to the ax_plat_data structure (with NULL being
compatible to the previous behaviour).
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add platform specific hooks for block transfer reads/writes of packet
buffer data, superseding the default provided ax_block_input/output.
Currently used for m68k Amiga XSurf100.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This complements the fix in 82533ad9a1 ("net: ethernet: ax88796:
don't call free_irq without request_irq first") that removed the
free_irq call in the error path of probe, to also not call free_irq
when remove is called to revert the effects of probe.
Fixes: 82533ad9a1 (net: ethernet: ax88796: don't call free_irq without request_irq first)
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call ax_mii_init in ax_open(), and unregister/remove mdiobus resources
in ax_close().
This is needed to be able to unload the module, as the module is busy
while the MII bus is attached.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
To read the MAC address from the (virtual) SAprom, the remote DMA
unit needs to be set up like for every other process access to card-local
memory.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Asix Electronics PHY found on the X-Surf 100 Amiga Zorro network
card by Individual Computers is buggy, and needs the reset bit toggled
as workaround to make a PHY soft reset succeed.
Add workaround driver just for this special case.
Suggested in xsurf100 patch series review by Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The platform data header file is now unused. Remove it, but add
an extra include which it brought in.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIOs are described in device tree using a list, without names.
Add defines to indicate what each index in the list means. These
defines should also be used by platform devices passing GPIOs via a
GPIO lookup table.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same parsing code can be used for both OF and platform devices, if
the platform device uses a gpiod_lookup_table. Parse these properties
directly into the bitbang structure, rather than use an intermediate
platform data structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving the allocation of this structure to the probe function is a
step towards making it the core data structure of the driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies the code, removing the need to handle active low
flags, etc.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
No current devices use IRQs in platform data, so remove support for
it. The MDIO core will also initialise the new bus such that all
addresses are polled, so remove the unneeded re-initialisation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not needed any more by devices using platform data, so remove
it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not needed any more by devices using platform data, so remove
it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio-gpio driver was the only user of the interface reset option.
Since it no longer uses it, remove it from the bit banging code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The platform data can contain a function to call to reset
the bit banging interface. It is not used, so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the prefix for fib6_info struct elements from rt6i_ to fib6_.
rt6i_pcpu and rt6i_exception_bucket are left as is given that they
point to rt6_info entries.
Rename only; not functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3_get_hdr_len() is used to calculate the header length which in
turn is used to calculate the gso_size for skb. When rxvlan offload is
disabled, vlan tag is present in the header and the function references
ip header from sizeof(ethhdr) and leads to incorrect pointer reference.
This patch fixes this issue by taking sizeof(vlan_ethhdr) into account
if vlan tag is present and correctly references the ip hdr.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Acked-by: Louis Luo <llouis@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables arm64 platform support for the HINIC driver.
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ACS Feature is currently enabled for GMAC >= 4 but the llc_snap status
is never checked in descriptor rx_status callback. This will cause
stmmac to always strip packets even that ACS feature is already
stripping them.
Lets be safe and disable the ACS feature for GMAC >= 4 and always strip
the packets for this GMAC version.
Fixes: 477286b53f ("stmmac: add GMAC4 core support")
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPv2 TX/RX descriptors uses 40bits DMA addresses, but 41 bits masks were
used (GENMASK_ULL(40, 0)).
This commit fixes that by using the correct mask.
Fixes: e7c5359f2e ("net: mvpp2: introduce PPv2.2 HW descriptors and adapt accessors")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the last rmnet device attached to a real device is removed, the
real device is unregistered from rmnet. As a result, the real device
lookup fails resulting in a warning when the fill_info handler is
called as part of the rmnet device unregistration.
Fix this by returning the rmnet flags as 0 when no real device is
present.
WARNING: CPU: 0 PID: 1779 at net/core/rtnetlink.c:3254
rtmsg_ifinfo_build_skb+0xca/0x10d
Modules linked in:
CPU: 0 PID: 1779 Comm: ip Not tainted 4.16.0-11872-g7ce2367 #1
Stack:
7fe655f0 60371ea3 00000000 00000000
60282bc6 6006b116 7fe65600 60371ee8
7fe65660 6003a68c 00000000 900000000
Call Trace:
[<6006b116>] ? printk+0x0/0x94
[<6001f375>] show_stack+0xfe/0x158
[<60371ea3>] ? dump_stack_print_info+0xe8/0xf1
[<60282bc6>] ? rtmsg_ifinfo_build_skb+0xca/0x10d
[<6006b116>] ? printk+0x0/0x94
[<60371ee8>] dump_stack+0x2a/0x2c
[<6003a68c>] __warn+0x10e/0x13e
[<6003a82c>] warn_slowpath_null+0x48/0x4f
[<60282bc6>] rtmsg_ifinfo_build_skb+0xca/0x10d
[<60282c4d>] rtmsg_ifinfo_event.part.37+0x1e/0x43
[<60282c2f>] ? rtmsg_ifinfo_event.part.37+0x0/0x43
[<60282d03>] rtmsg_ifinfo+0x24/0x28
[<60264e86>] dev_close_many+0xba/0x119
[<60282cdf>] ? rtmsg_ifinfo+0x0/0x28
[<6027c225>] ? rtnl_is_locked+0x0/0x1c
[<6026ca67>] rollback_registered_many+0x1ae/0x4ae
[<600314be>] ? unblock_signals+0x0/0xae
[<6026cdc0>] ? unregister_netdevice_queue+0x19/0xec
[<6026ceec>] unregister_netdevice_many+0x21/0xa1
[<6027c765>] rtnl_delete_link+0x3e/0x4e
[<60280ecb>] rtnl_dellink+0x262/0x29c
[<6027c241>] ? rtnl_get_link+0x0/0x3e
[<6027f867>] rtnetlink_rcv_msg+0x235/0x274
Fixes: be81a85f5f ("net: qualcomm: rmnet: Implement fill_info")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the NetVSP v6 and 6.1 message structures, and includes
these versions into NetVSC/NetVSP version negotiation process.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implement the 'Device Naming' feature of the Hyper-V
network device API. In Hyper-V on the host through the GUI or PowerShell
it is possible to enable the device naming feature which causes
the host to make available to the guest the name of the device.
This shows up in the RNDIS protocol as the friendly name.
The name has no particular meaning and is limited to 256 characters.
The value can only be set via PowerShell on the host, but could
be scripted for mass deployments. The default value is the
string 'Network Adapter' and since that is the same for all devices
and useless, the driver ignores it.
In Windows, the value goes into a registry key for use in SNMP
ifAlias. For Linux, this patch puts the value in the network
device alias property; where it is visible in ip tools and SNMP.
The host provided ifAlias is just a suggestion, and can be
overridden by later ip commands.
Also requires exporting dev_set_alias in netdev core.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the chip configuration entries only RTL8169 (ver <= 06)
supports tx checksumming for jumbo packets.
By the way: constant JUMBO_1K is a little misleading because it refers
to the standard packet size and not to a jumbo packet size.
By implementing this rule we can get rid of configuring tx checksumming
support per chip type.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The region to be used is always the first of type IORESOURCE_MEM.
We can implement this rule directly w/o having to specify which
region is the first one per configuration entry.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
txd_version is used in rtl_init_one() only, so we can drop member
txd_version from struct rtl8169_private.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain entries in array mac_info[] are redundant, so remove them:
0x7cf, 0x2c200000 (VER 33): matched by entry 0x7c8, 0x2c000000
0x7cf, 0x28300000 (VER 26): matched by entry 0x7c8, 0x28000000
0x7cf, 0x3cb00000 (VER 24): matched by entry 0x7c8, 0x3c800000
0x7cf, 0x3c400000 (VER 22): matched by entry 0x7c8, 0x3c000000
0x7cf, 0x38500000 (VER 17): matched by entry 0x7c8, 0x38000000
0x7cf, 0x44900000 (VER 39): matched by entry 0x7c8, 0x44800000
0x7cf, 0x40b00000 (VER 30): matched by entry 0x7c8, 0x40800000
0x7cf, 0x40a00000 (VER 30): matched by entry 0x7c8, 0x40800000
0x7cf, 0x34a00000 (VER 09): matched by entry 0x7c8, 0x34800000
0x7cf, 0x24a00000 (VER 09): matched by entry 0x7c8, 0x24800000
In addition don't mask out bits 30 and 29 when printing the XID.
Most likely this is a relict from the times when the driver covered
RTL8169 chip version only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For security reasons since commit ad67b74d24 "printk: hash addresses
printed with %p" %p doesn't display the full address any longer.
We could switch to %px, but I think the pointer address doesn't
provide a real benefit, so remove printing the hashed address.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can get rid of member opts1_mask and in addition save a few cpu
cycles in the hot path of rtl_rx().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code can be a little simplified by switching the interrupt handler
argument type to struct rtl8169_private *.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The counter handling functions don't deal with the net_device, so code
can be simplified by changing the argument type to
struct rtl8169_private *.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code can be simplified by changing the argument type of hw_start
callbacks from struct net_device * to struct rtl8169_private *.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is very simple and used only once, so we can inline
the two statements.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_buf_sz is constant, so we don't have to pass it as parameter and
in general can replace it with a constant.
When working on this I noticed that also before in
rtl_set_rx_max_size() a value of 0x4000 is set, what is not in line
with the chip spec. According to the spec only bits 0..13 are used
and we set an effective value of zero therefore.
However, the driver still seems to work and due to potential side
effects I'm reluctant to make a change.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8169_rx_fill() is called only once and directly before the call
array tp->Rx_databuff[] is filled with zero's. Therefore we don't
need this check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function doesn't use the net_device, therefore change the
parameter to type struct rtl8169_private * to simplify the code.
In addition we don't need the calculations in the memset
statements, we can use the size of the arrays directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev->dev.parent has the same value as tp_to_dev(tp)
(set by SET_NETDEV_DEV() in rtl_init_one()) and we know it can't be NULL.
This allows us to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_schedule() is called from hard irq context, so we can switch to
napi_schedule_irqoff() and avoid some overhead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can use generic constant NAPI_POLL_WAIT instead of defining an own
constant for the same value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not a giant leap for mankind, but let's avoid the open-coded memcpy
and use standard helper skb_copy_to_linear_data instead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 6f0333b8fd "r8169: use 50% less ram for RX ring" member
align isn't used any longer, so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Member features of struct rtl8169_private isn't used any longer since
commit 6c6aa15fde "r8169: improve interrupt handling", so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for promiscuous mode in k2g's network
driver. When upper layer instructs to transition from
non-promiscuous mode to promiscuous mode or vice versa
K2G network driver needs to configure ALE accordingly
so that in case of non-promiscuous mode, ALE will not flood
all unicast packets to host port, while in promiscuous
mode, it will pass all received unicast packets to
host port.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an API to support setting rx mode in
netcp modules. If a netcp module needs to be notified
when upper layer transitions from one rx mode to
another and react accordingly, such a module will implement
the new API set_rx_mode added in this patch. Currently
rx modes supported are PROMISCUOUS and NON_PROMISCUOUS
modes.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netcp driver shouldn't proceed until the knav qmss and dma
devices are ready. So return -EPROBE_DEFER if these devices are not
ready.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the probe sequence is not guaranteed contrary to the assumption
of the commit 2d8e276a9030, same has to be reverted.
commit 2d8e276a9030 ("net: netcp: remove dead code from the driver")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy used for K2G allows for internal delays to be added optionally
to the clock circuitry based on board desing. To add this support,
enhance the driver to use of_get_phy_mode() to read the phy-mode from
the phy device and pass the same to phy through of_phy_connect().
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stats block in 2u cpsw hardware is similar to the one on nu
and hence handle it in a similar way by using a macro that includes
2u hardware as well.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently support only vlan priority zero. So map the
vlan priorities to zero flow in hardware.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce rgmii link status to handle link state events for 2u
cpsw hardware on K2G.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2u cpsw hardware on K2G uses rgmii link to interface with Phy. So add
support for this interface in the code so that driver can be re-used
for 2u hardware.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to add support for 2u cpsw hardware found on
K2G SoC, make sgmii configuration conditional. This is required
since 2u uses RGMII interface instead of SGMII and to allow for driver
re-use.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vinicius Costa Gomes