Move bootloaders reads/writes into separate functions. Instead of switching
client->addr, define new field bootloader_addr in mxt_data. Implement
lookup calculation for bootloader addresses.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The configuration is stored in NVRAM on the maXTouch chip. When the device
is reset it reports a CRC of the stored configuration values. Therefore it
isn't necessary to send the configuration on each probe - we can check the
CRC matches and avoid a timeconsuming backup/reset cycle.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The delay before the chip can be accessed after reset varies between
different chips in maXTouch family. Waiting for an interrupt and a T6
status message with the RESET bit set is a better behaviour.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rather than msleep for MXT_RESET_TIME and MXT_FWRESET_TIME during the
transition to bootloader mode and the transition back from app, wait for
the CHG assert to indicate that the transition is done.
This change replaces the msleep with a wait for completion that the
mxt_interrupt handler signals.
Also add CHG poll after last firmware frame - some bootloader versions will
assert the interrupt line after the final frame, in testing this meant that
the driver attempts to read the info block too early whilst the chip is
still resetting.
This improves firmware update time as we no longer wait longer than
necessary for each reset.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver should not immediately read bootloader status when in
Application Update Mode. The CHG line will assert when the device has made
a state transition and is ready to report a new status via i2c.
This change adds a wait for completion in mxt_check_bootloader, and changes
the mxt_interrupt handler to signal the completion.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
These two object table entry fields are reported 1 less than their value.
When used, however, we always want the actual size and instances.
To keep the object size and instances 1-byte fields, and thus preserve
the object-table struct's 6-byte packed alignment, add some convenient
accessor functions that do the +1 every time these fields are accessed.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* The mapping of the GPIO numbers into the T19 status byte varies between
different maXTouch chips. Some have up to 7 GPIOs. Allowing a keycode array
of up to 8 items is simpler and more generic. So replace #define with
configurable number of keys which also allows the removal of is_tp.
* Rename platform data parameters to include "t19" to prevent confusion with
T15 key array.
* Probe aborts early on when pdata is NULL, so no need to check.
* Move "int i" to beginning of function (mixed declarations and code)
* Use API calls rather than __set_bit()
* Remove unused dev variable.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is not necessary to download these values to the maXTouch chip on every
probe, since they are stored in NVRAM. It makes life difficult when tuning
the device to keep them in sync with the config array/file, and requires a
new kernel build for minor tweaks.
These parameters only represent a tiny subset of the available
configuration options, tracking all of these options in platform data would
be a endless task. In addition, different versions of maXTouch chips may
have these values in different places or may not even have them at all.
Having these values also makes life more complex for device tree and other
platforms where having to define a static configuration isn't helpful.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Improve the suspend and resume handlers to allow the device
to wakeup the system from suspend.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Get rid of the attb_read_val() platform hook. Instead, read the ATTB gpio
directly from the driver.
Fail if valid ATTB gpio is not provided by patform data.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Introduce helper functions to configure power and interrupt registers.
Default to IDLE mode on probe as device supports auto wakeup to ACVIE mode
on detecting finger touch.
Configure interrupt mode and polarity on start up. Power down on device
closure or module removal.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use devm_() and friends for allocating memory, input device
and IRQ.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In case allocation via usb_alloc_coherent() fails in ims_pcu_buffers_alloc(),
the function jumps to the exit path without initializing local variable
'error' that is used as return value. Detected by Coverity - CID 1016531.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds support for the 0x4004, 0x5000, and 0x5002 sensors found
on what should be the Motion R12, Fujitsu Q704, and Fujitsu T904. These
tablets use a new report ID (3) for their touch packets and a slightly
different HID descriptor format, but are otherwise largely identical in
protocol to the "MTTPC" tablets.
Note:
* The R12 uses its 0x4004 sensor for touch input only. A pen interface
is not present in its HID descriptor, though its possible a 0x4004
may be used for pen input by other tablet PCs in the future.
* The 0x5002 sensor appears to use a new report ID (8) for its pen
packets. The other sensors continue to use the traditional report
ID (2).
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A few cases of incorrectly using 'le16_to_cpup' instead of
'get_unaligned_le16' have been noticed and fixed.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTbTZoAAoJEHm+PkMAQRiGLssH/3Rv6e9rAkEw9Ey0ymwGsCvf
6DEAcSgaWEyYWEU+DmkEQ3hbiOyESHFOsWE4zA2F5WY0w2Xsr+wDCS+14WCN6NHT
6sxSYGj1hd+ni6GhlGxfRpUXtY59h7TKHaaHYKPIOsO4OWXVeD53trpq416kvqal
zWkFOWeiEyeJnNKv0z0+5QWTeFDjTd1YawWcK/8kFez1Y4BXBECTgKoJaEcvowfU
j7oQ0BJxtLlxFgCB84bZTUbGuyn1x9FiS7Z2w9JcqSkTLMabFjsbA15eZIV66N4s
boaxlRvyvelR09eiiYYqOLxUmeEi1wRqtAM3yln1Y5/MX+DAmf5/sylqKtC5eLg=
=ezkr
-----END PGP SIGNATURE-----
Merge tag 'v3.15-rc5' into next
Merge with Linux 3.15-rc5 to sync up Wacom and other changes.
If the debounce time is 0 our usage of ilog2() later on in this driver will
cause undefined behavior. If CONFIG_OF=n this fact is evident to the
compiler, and it emits a call to ____ilog2_NaN() which doesn't exist. Fix
this by setting a sane default for debounce and failing to probe if
debounce is 0 in the DT.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Win8 version of the Panasonic CF-H2 includes a new Wacom device.
The pen interface appears to use the same protocol as before, but the
touch interface has been tweaked to send Win8-compatible reports.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The sun4i resisitive touchscreen controller also comes with a built-in
temperature sensor. This commit adds support for it.
This commit also introduces a new "ts-attached" device-tree property,
when this is not set, the input part of the driver won't register. This way
the internal temperature sensor can be used to measure the SoC temperature
independent of there actually being a touchscreen attached to the controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Note the sun4i-ts controller is capable of detecting a second touch, but
when a second touch is present then the accuracy becomes so bad the
reported touch location is not useable.
The original android driver contains some complicated heuristics using the
aprox. distance between the 2 touches to see if the user is making a pinch
open / close movement, and then reports emulated multi-touch events around
the last touch coordinate (as the dual-touch coordinates are worthless).
These kinds of heuristics are just asking for trouble (and don't belong in
the kernel). So this driver offers straight forward, reliable single touch
functionality only.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Managed resources are becoming more and more popular in drivers. Let's
implement managed polled input devices, to complement managed regular input
devices.
Similarly to managed regular input devices only one new call
devm_input_allocate_polled_device() is added and the rest of APIs is
modified to work with both managed and non-managed devices.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Polled device's attributes controlling polling rate and whether polling is
enabled are attached to input device. We should have device core
instantiate them for us, so that they are created by the time new device
notification is sent to userspace, instead of doing it ourselves
afterwards.
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Replace existing gpio resource handling in the driver with managed
resources, this ensures more consistent error values and simplifies error
paths.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch simplifies GPIO handling in the driver by using GPIO functions
based on descriptors. As a result this driver now can be used for boards
without DT support.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Simplify the driver by using managed resources for memory allocation of
internal structure, input device allocation and irq request.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Change some dev_dbg() invocations to dev_err() ones, because they
are supposed to output error messages.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This makes the error handling much more simpler than open-coding everything
and in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Using devm_regulator_bulk_get() and devm_input_allocate_device() can make
the code cleaner and smaller as we do not need to manually free resources
the error and remove paths.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
While searching for users of spi_async() I found a reference in the ad7877
driver to using it to initiate data transfer from the interrupt handler.
However there is no code for this, instead the interrupt handler is a
threaded handler and uses spi_sync() instead.
Remove the bitrotted comment, though in actual fact the use case mentioned
is a great use for spi_async() since it would cut down on latency handling
the interrupt by saving us a context switch before we start SPI.
This was previously implemented, it was removed in commit b534422b2d
(Input: ad7877 - switch to using threaded IRQ) for code complexity reasons.
It may be better to revert that commit instead.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We put this workaround in 2008 and the offending userspace has been fixed
up long time ago; the link in the message is no longer valid either, so it
is time to retire it.
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds ST Keyscan driver to use the keypad hw a subset of ST
boards provide. Specific board setup will be put in the given dt.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
While searching for users of spi_async() I got a false positive in the
ads7846 driver, fix that.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Implement device tree probing for the tc3589x keypad driver.
This is modeled on the STMPE keypad driver and tested on the
Ux500 TVK1281618 UIB.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The w90p910_ts touchscreen driver is heavily architecture dependent,
so there is no point in letting it be built on other architectures
than it was written for.
All other W90P910/W90X900 drivers already have that dependency, so it
makes things more consistent and configuration easier.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Recent ARM boards have the KMI devices share one interrupt line rather
than having dedicated IRQs. Update the driver to take that into account.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The number of columns of pxa27x-keypad used by various boards is not fixed.
When building keymap with call to:
matrix_keypad_build_keymap(keymap_data, NULL,
pdata->matrix_key_rows,
pdata->matrix_key_cols,
keypad->keycodes, input_dev);
it will internally calculate needed row shift and use it to fill the
keymap. Therefore when calculating the "scancode" we should no longer use
constant row shift but also calculate it from number of columns.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Building this driver on ARM/at91 always gives us this error message:
drivers/input/touchscreen/atmel-wm97xx.c:63:2: error: #error Unknown CPU, this driver only supports AT32AP700X CPUs.
Clearly this configuration is not meant to work, so let's just prevent
it in Kconfig. If we ever want to use it on another platform, we should
also pass proper resources for GPIO, IRQ and memory, which are hardcoded
to AT32AP700X at the moment.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ps2 mouse and keyboard drivers use the "serio" framework that they
correctly select in Kconfig, and that in turn depends on the i8042 driver,
which is also allowed to be disabled for architectures that don't have an
i8042.
However, Kconfig also allows i8042 to be built as a module while
the serio framework is built-in, which causes this link error:
drivers/built-in.o: In function `ps2_begin_command':
:(.text+0x26b6cc): undefined reference to `i8042_check_port_owner'
:(.text+0x26b6d4): undefined reference to `i8042_lock_chip'
drivers/built-in.o: In function `ps2_end_command':
:(.text+0x26b734): undefined reference to `i8042_check_port_owner'
:(.text+0x26b73c): undefined reference to `i8042_unlock_chip'
On x86, a specific 'select SERIO_I8042' takes care of it, but
not on the other architecture that potentially have a i8042.
This patch changes the Kconfig logic to ensure that whenever
there is an i8042, it does get used for the serio driver, avoiding
the link error above.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem fixes from Dmitry Torokhov:
"Just a few fixups to various drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - fix touchpad initialization on Gigabyte U2442
Input: tca8418 - fix loading this driver as a module from a device tree
Input: bma150 - extend chip detection for bma180
Input: atkbd - fix keyboard not working on some LG laptops
Input: synaptics - add min/max quirk for ThinkPad Edge E431
The atmel_tsadcc driver is not used anymore, it has been replaced by at91_adc so
remove it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The hw_version 3 Elantech touchpad on the Gigabyte U2442 does not accept
0x0b as initialization value for r10, this stand-alone version of the
driver: http://planet76.com/drivers/elantech/psmouse-elantech-v6.tar.bz2
Uses 0x03 which does work, so this means not setting bit 3 of r10 which
sets: "Enable Real H/W Resolution In Absolute mode"
Which will result in half the x and y resolution we get with that bit set,
so simply not setting it everywhere is not a solution. We've been unable to
find a way to identify touchpads where setting the bit will fail, so this
patch uses a dmi based blacklist for this.
https://bugzilla.kernel.org/show_bug.cgi?id=61151
Cc: stable@vger.kernel.org
Reported-by: Philipp Wolfer <ph.wolfer@gmail.com>
Tested-by: Philipp Wolfer <ph.wolfer@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Loading the tca8418 driver as a module on a device tree based system needs
a MODULE_ALIAS because the driver name does not match the automatic
name generation rules of a 'compatible' entry on i2c bus.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver has been used while on the OpenPhoenux GTA04 with a BMA180.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
After issuing ATKBD_CMD_RESET_DIS, keyboard on some LG laptops stops
working. The workaround is to stop issuing ATKBD_CMD_RESET_DIS commands.
In order to keep changes in atkbd driver to the minimum we check DMI
signature and only skip ATKBD_CMD_RESET_DIS if we are running on LG
LW25-B7HV or P1-J273B.
Cc: stable@vger.kernel.org
Signed-off-by: Sheng-Liang Song <ssl@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"The main change is that we now publish "firmware ID" for the serio
devices to help userspace figure out the kind of touchpads it is
dealing with: i8042 will export PS/2 port's PNP IDs as firmware IDs.
You will also get more quirks for Synaptics touchpads in various
Lenovo laptops, a change to elantech driver to recognize even more
models, and fixups to wacom and couple other drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - add support for newer elantech touchpads
Input: soc_button_array - fix a crash during rmmod
Input: synaptics - add min/max quirk for ThinkPad T431s, L440, L540, S1 Yoga and X1
Input: synaptics - report INPUT_PROP_TOPBUTTONPAD property
Input: Add INPUT_PROP_TOPBUTTONPAD device property
Input: i8042 - add firmware_id support
Input: serio - add firmware_id sysfs attribute
Input: wacom - handle 1024 pressure levels in wacom_tpc_pen
Input: wacom - references to 'wacom->data' should use 'unsigned char*'
Input: wacom - override 'pressure_max' with value from HID_USAGE_PRESSURE
Input: wacom - use full 32-bit HID Usage value in switch statement
Input: wacom - missed the last bit of expresskey for DTU-1031
Input: ads7846 - fix device usage within attribute show
Input: da9055_onkey - remove use of regmap_irq_get_virq()
Newer elantech touchpads are not recognized by the current driver, since it
fails to detect their firmware version number. This prevents more advanced
touchpad features from being usable such as two-finger scrolling. This
patch allows newer touchpads to be detected and be fully functional. Tested
on Sony Vaio SVF13N17PXB.
Signed-off-by: Jordan Rife <jrife0@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When the system has zero or one button available, trying to rmmod
soc_button_array will cause crash. Fix this by properly handling -ENODEV
in probe().
Signed-off-by: Lejun Zhu <lejun.zhu@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We expect that all the Haswell series will need such quirks, sigh.
The T431s seems to be T430 hardware in a T440s case, using the T440s touchpad,
with the same min/max issue.
The X1 Carbon 3rd generation name says 2nd while it is a 3rd generation.
The X1 and T431s share a PnPID with the T540p, but the reported ranges are
closer to those of the T440s.
HdG: Squashed 5 quirk patches into one. T431s + L440 + L540 are written by me,
S1 Yoga and X1 are written by Benjamin Tissoires.
Hdg: Standardized S1 Yoga and X1 values, Yoga uses the same touchpad as the
X240, X1 uses the same touchpad as the T440.
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Check PNP ID of the PS/2 AUX port and report INPUT_PROP_TOPBUTTONPAD
property for for touchpads with top button areas.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fill in the new serio firmware_id sysfs attribute for pnp instantiated
8042 serio ports.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
serio devices exposed via platform firmware interfaces such as ACPI may
provide additional identifying information of use to userspace.
We don't associate the serio devices with the firmware device (we don't
set it as parent), so there's no way for userspace to make use of this
information.
We cannot change the parent for serio devices instantiated though a
firmware interface as that would break suspend / resume ordering.
Therefore this patch adds a new firmware_id sysfs attribute so that
userspace can get a string from there with any additional identifying
information the firmware interface may provide.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some tablet PC sensors (e.g. the 0xEC found in the Thinkpad Yoga) report
more than 256 pressure levels and will experience wraparound unless the
full range is read.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Aaron Skomra <Aaron.Skomra@wacom.com>
Reviewed-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
'wacom->data' contains raw binary data and can lead to unexpected behavior
if a byte under examination happens to have its MSB set.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Aaron Skomra <Aaron.Skomra@wacom.com>
Reviewed-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The 0xEC sensor is used in multiple tablet PCs and curiously has versions
that report 256 levels of pressure (Samsung Slate 7) as well as versions
that report 1024 levels (Lenovo Thinkpad Yoga). To allow both versions to
work properly, we allow the value of HID_USAGE_PRESSURE reported to
override pressure_max.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Aaron Skomra <Aaron.Skomra@wacom.com>
Reviewed-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A HID Usage is a 32-bit value: an upper 16-bit "page" and a lower 16-bit
ID. While the two halves are normally reported seperately, only the
combination uniquely idenfifes a particular HID Usage.
The existing code performs the comparison in two steps, first performing a
switch on the ID and then verifying the page within each case. While this
works fine, it is very akward to handle two Usages that share a single ID,
such as HID_USAGE_PRESSURE and HID_USAGE_X because the case statement can
only have a single identifier.
To work around this, we now check the full 32-bit HID Usage directly rather
than first checking the ID and then the page. This allows the switch
statement to have distinct cases for e.g. HID_USAGE_PRESSURE and
HID_USAGE_X.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Aaron Skomra <Aaron.Skomra@wacom.com>
Reviewed-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
With commit e585c40ba (Input: ads7846 - convert to
hwmon_device_register_with_groups()) the device passed to the attribute's
show function isn't the spi device as before.
So fixup the passed device to ads7846_read12_ser.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Using platform_get_irq_byname() to retrieve the IRQ number returns the
VIRQ number rather than the local IRQ number for the device. Passing that
value then into regmap_irq_get_virq() causes a failure because the
function is expecting the local IRQ number (e.g. 0, 1, 2, 3, etc).
This patch removes use of regmap_irq_get_virq() to prevent this failure
from happening.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The legacy HAVE_PWM Kconfig symbol is finally being retired. Thanks a
lot to Sascha Hauer for doing that.
Three new drivers are added: Freescale FTM, Cirrus Logic CLPS711X and
Intel Low Power Subsystem.
An assortment of fixes and cleanups rounds things off for this release
cycle.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=pbF+
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm changes from Thierry Reding:
"The legacy HAVE_PWM Kconfig symbol is finally being retired. Thanks a
lot to Sascha Hauer for doing that.
Three new drivers are added: Freescale FTM, Cirrus Logic CLPS711X and
Intel Low Power Subsystem.
An assortment of fixes and cleanups rounds things off for this release
cycle"
* tag 'pwm/for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: pxa: Constify OF match table
pwm: pxa: Fix typo "pwm" -> "PWM"
Revert "pwm: pxa: Use of_match_ptr()"
pwm: add support for Intel Low Power Subsystem PWM
pwm: Add CLPS711X PWM support
pwm: atmel: correct CDTY calculation
pwm: atmel: Fix polarity handling
Documentation: Add device tree bindings for Freescale FTM PWM.
pwm: Add Freescale FTM PWM driver support
pwm: pxa: Use of_match_ptr()
pwm: samsung: Use SIMPLE_DEV_PM_OPS macro
pwm: renesas-tpu: Add dependency on HAS_IOMEM
pwm: Remove obsolete HAVE_PWM Kconfig symbol
These cleanup patches are mainly move stuff around and should all
be harmless. They are mainly split out so that other branches can
be based on top to avoid conflicts.
Notable changes are:
* We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
longer used. (Uwe Kleine-König)
* The Qualcomm MSM platform is split out into legacy mach-msm and
new-style mach-qcom, to allow easier maintainance of the new
hardware support without regressions. (Kumar Gala)
* A rework of some of the Kconfig logic to simplify multiplatform
support (Rob Herring)
* Samsung Exynos gets closer to supporting multiplatform (Sachin
Kamat and others)
* mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
* at91 gains some common clock framework support (Alexandre Belloni,
Jean-Jacques Hiblot and other French people).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GcBb
-----END PGP SIGNATURE-----
Merge tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"These cleanup patches are mainly move stuff around and should all be
harmless. They are mainly split out so that other branches can be
based on top to avoid conflicts.
Notable changes are:
- We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
longer used (Uwe Kleine-König)
- The Qualcomm MSM platform is split out into legacy mach-msm and
new-style mach-qcom, to allow easier maintainance of the new
hardware support without regressions (Kumar Gala)
- A rework of some of the Kconfig logic to simplify multiplatform
support (Rob Herring)
- Samsung Exynos gets closer to supporting multiplatform (Sachin
Kamat and others)
- mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
- at91 gains some common clock framework support (Alexandre Belloni,
Jean-Jacques Hiblot and other French people)"
* tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (89 commits)
ARM: hisi: select HAVE_ARM_SCU only for SMP
ARM: efm32: allow uncompress debug output
ARM: prima2: build reset code standalone
ARM: at91: add PWM clock
ARM: at91: move sam9261 SoC to common clk
ARM: at91: prepare common clk transition for sam9261 SoC
ARM: at91: updated the at91_dt_defconfig with support for the ADS7846
ARM: at91: dt: sam9261: Device Tree support for the at91sam9261ek
ARM: at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs
ARM: at91: dt: Add at91sam9261 dt SoC support
ARM: at91: switch sam9rl to common clock framework
ARM: at91/dt: define main clk frequency of at91sam9rlek
ARM: at91/dt: define at91sam9rl clocks
ARM: at91: prepare common clk transition for sam9rl SoCs
ARM: at91: prepare sam9 dt boards transition to common clk
ARM: at91: dt: sam9rl: Device Tree for the at91sam9rlek
ARM: at91/defconfig: Add the sam9rl to the list of DT-enabled SOCs
ARM: at91: Add at91sam9rl DT SoC support
ARM: at91: prepare at91sam9rl DT transition
ARM: at91/defconfig: refresh at91sam9260_9g20_defconfig
...
Pull input updates from Dmitry Torokhov:
"The first round of updates for the input subsystem.
Just new drivers and existing driver fixes, no core changes except for
the new uinput IOCTL to allow userspace to fetch sysfs name of the
input device that was created"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (43 commits)
Input: edt-ft5x06 - add a missing condition
Input: appletouch - fix jumps when additional fingers are detected
Input: appletouch - implement sensor data smoothing
Input: add driver for SOC button array
Input: pm8xxx-vibrator - add DT match table
Input: pmic8xxx-pwrkey - migrate to DT
Input: pmic8xxx-keypad - migrate to DT
Input: pmic8xxx-keypad - migrate to regmap APIs
Input: pmic8xxx-keypad - migrate to devm_* APIs
Input: pmic8xxx-keypad - fix build by removing gpio configuration
Input: add new driver for ARM CLPS711X keypad
Input: edt-ft5x06 - add support for M09 firmware version
Input: edt-ft5x06 - ignore touchdown events
Input: edt-ft5x06 - adjust delays to conform datasheet
Input: edt-ft5x06 - add DT support
Input: edt-ft5x06 - several cleanups; no functional change
Input: appletouch - dial back fuzz setting
Input: remove obsolete tnetv107x drivers
Input: sirfsoc-onkey - set the capability of reporting KEY_POWER
Input: da9052_onkey - use correct register bit for key status
...
The if condition was accidentally deleted here so we return every time
instead of returning on error.
Fixes: fd335ab04b ('Input: edt-ft5x06 - add support for M09 firmware version')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-By: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- Device PM QoS support for latency tolerance constraints on systems with
hardware interfaces allowing such constraints to be specified. That is
necessary to prevent hardware-driven power management from becoming
overly aggressive on some systems and to prevent power management
features leading to excessive latencies from being used in some cases.
- Consolidation of the handling of ACPI hotplug notifications for device
objects. This causes all device hotplug notifications to go through
the root notify handler (that was executed for all of them anyway
before) that propagates them to individual subsystems, if necessary,
by executing callbacks provided by those subsystems (those callbacks
are associated with struct acpi_device objects during device
enumeration). As a result, the code in question becomes both smaller
in size and more straightforward and all of those changes should not
affect users.
- ACPICA update, including fixes related to the handling of _PRT in cases
when it is broken and the addition of "Windows 2013" to the list of
supported "features" for _OSI (which is necessary to support systems
that work incorrectly or don't even boot without it). Changes from
Bob Moore and Lv Zheng.
- Consolidation of ACPI _OST handling from Jiang Liu.
- ACPI battery and AC fixes allowing unusual system configurations to
be handled by that code from Alexander Mezin.
- New device IDs for the ACPI LPSS driver from Chiau Ee Chew.
- ACPI fan and thermal optimizations related to system suspend and resume
from Aaron Lu.
- Cleanups related to ACPI video from Jean Delvare.
- Assorted ACPI fixes and cleanups from Al Stone, Hanjun Guo, Lan Tianyu,
Paul Bolle, Tomasz Nowicki.
- Intel RAPL (Running Average Power Limits) driver cleanups from Jacob Pan.
- intel_pstate fixes and cleanups from Dirk Brandewie.
- cpufreq fixes related to system suspend/resume handling from Viresh Kumar.
- cpufreq core fixes and cleanups from Viresh Kumar, Stratos Karafotis,
Saravana Kannan, Rashika Kheria, Joe Perches.
- cpufreq drivers updates from Viresh Kumar, Zhuoyu Zhang, Rob Herring.
- cpuidle fixes related to the menu governor from Tuukka Tikkanen.
- cpuidle fix related to coupled CPUs handling from Paul Burton.
- Asynchronous execution of all device suspend and resume callbacks,
except for ->prepare and ->complete, during system suspend and resume
from Chuansheng Liu.
- Delayed resuming of runtime-suspended devices during system suspend for
the PCI bus type and ACPI PM domain.
- New set of PM helper routines to allow device runtime PM callbacks to
be used during system suspend and resume more easily from Ulf Hansson.
- Assorted fixes and cleanups in the PM core from Geert Uytterhoeven,
Prabhakar Lad, Philipp Zabel, Rashika Kheria, Sebastian Capella.
- devfreq fix from Saravana Kannan.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=ywR6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"The majority of this material spent some time in linux-next, some of
it even several weeks. There are a few relatively fresh commits in
it, but they are mostly fixes and simple cleanups.
ACPI took the lead this time, both in terms of the number of commits
and the number of modified lines of code, cpufreq follows and there
are a few changes in the PM core and in cpuidle too.
A new feature that already got some LWN.net's attention is the device
PM QoS extension allowing latency tolerance requirements to be
propagated from leaf devices to their ancestors with hardware
interfaces for specifying latency tolerance. That should help systems
with hardware-driven power management to avoid going too far with it
in cases when there are latency tolerance constraints.
There also are some significant changes in the ACPI core related to
the way in which hotplug notifications are handled. They affect PCI
hotplug (ACPIPHP) and the ACPI dock station code too. The bottom line
is that all those notification now go through the root notify handler
and are propagated to the interested subsystems by means of callbacks
instead of having to install a notify handler for each device object
that we can potentially get hotplug notifications for.
In addition to that ACPICA will now advertise "Windows 2013"
compatibility for _OSI, because some systems out there don't work
correctly if that is not done (some of them don't even boot).
On the system suspend side of things, all of the device suspend and
resume callbacks, except for ->prepare() and ->complete(), are now
going to be executed asynchronously as that turns out to speed up
system suspend and resume on some platforms quite significantly and we
have a few more optimizations in that area.
Apart from that, there are some new device IDs and fixes and cleanups
all over. In particular, the system suspend and resume handling by
cpufreq should be improved and the cpuidle menu governor should be a
bit more robust now.
Specifics:
- Device PM QoS support for latency tolerance constraints on systems
with hardware interfaces allowing such constraints to be specified.
That is necessary to prevent hardware-driven power management from
becoming overly aggressive on some systems and to prevent power
management features leading to excessive latencies from being used
in some cases.
- Consolidation of the handling of ACPI hotplug notifications for
device objects. This causes all device hotplug notifications to go
through the root notify handler (that was executed for all of them
anyway before) that propagates them to individual subsystems, if
necessary, by executing callbacks provided by those subsystems
(those callbacks are associated with struct acpi_device objects
during device enumeration). As a result, the code in question
becomes both smaller in size and more straightforward and all of
those changes should not affect users.
- ACPICA update, including fixes related to the handling of _PRT in
cases when it is broken and the addition of "Windows 2013" to the
list of supported "features" for _OSI (which is necessary to
support systems that work incorrectly or don't even boot without
it). Changes from Bob Moore and Lv Zheng.
- Consolidation of ACPI _OST handling from Jiang Liu.
- ACPI battery and AC fixes allowing unusual system configurations to
be handled by that code from Alexander Mezin.
- New device IDs for the ACPI LPSS driver from Chiau Ee Chew.
- ACPI fan and thermal optimizations related to system suspend and
resume from Aaron Lu.
- Cleanups related to ACPI video from Jean Delvare.
- Assorted ACPI fixes and cleanups from Al Stone, Hanjun Guo, Lan
Tianyu, Paul Bolle, Tomasz Nowicki.
- Intel RAPL (Running Average Power Limits) driver cleanups from
Jacob Pan.
- intel_pstate fixes and cleanups from Dirk Brandewie.
- cpufreq fixes related to system suspend/resume handling from Viresh
Kumar.
- cpufreq core fixes and cleanups from Viresh Kumar, Stratos
Karafotis, Saravana Kannan, Rashika Kheria, Joe Perches.
- cpufreq drivers updates from Viresh Kumar, Zhuoyu Zhang, Rob
Herring.
- cpuidle fixes related to the menu governor from Tuukka Tikkanen.
- cpuidle fix related to coupled CPUs handling from Paul Burton.
- Asynchronous execution of all device suspend and resume callbacks,
except for ->prepare and ->complete, during system suspend and
resume from Chuansheng Liu.
- Delayed resuming of runtime-suspended devices during system suspend
for the PCI bus type and ACPI PM domain.
- New set of PM helper routines to allow device runtime PM callbacks
to be used during system suspend and resume more easily from Ulf
Hansson.
- Assorted fixes and cleanups in the PM core from Geert Uytterhoeven,
Prabhakar Lad, Philipp Zabel, Rashika Kheria, Sebastian Capella.
- devfreq fix from Saravana Kannan"
* tag 'pm+acpi-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (162 commits)
PM / devfreq: Rewrite devfreq_update_status() to fix multiple bugs
PM / sleep: Correct whitespace errors in <linux/pm.h>
intel_pstate: Set core to min P state during core offline
cpufreq: Add stop CPU callback to cpufreq_driver interface
cpufreq: Remove unnecessary braces
cpufreq: Fix checkpatch errors and warnings
cpufreq: powerpc: add cpufreq transition latency for FSL e500mc SoCs
MAINTAINERS: Reorder maintainer addresses for PM and ACPI
PM / Runtime: Update runtime_idle() documentation for return value meaning
video / output: Drop display output class support
fujitsu-laptop: Drop unneeded include
acer-wmi: Stop selecting VIDEO_OUTPUT_CONTROL
ACPI / gpu / drm: Stop selecting VIDEO_OUTPUT_CONTROL
ACPI / video: fix ACPI_VIDEO dependencies
cpufreq: remove unused notifier: CPUFREQ_{SUSPENDCHANGE|RESUMECHANGE}
cpufreq: Do not allow ->setpolicy drivers to provide ->target
cpufreq: arm_big_little: set 'physical_cluster' for each CPU
cpufreq: arm_big_little: make vexpress driver depend on bL core driver
ACPI / button: Add ACPI Button event via netlink routine
ACPI: Remove duplicate definitions of PREFIX
...
Addresses issues related to when a second finger enters or leaves the
field, causing the cursor to jump or the page to scroll unexpectedly; now,
we discard any movement change that happens at the exact moment we detect a
change in the number of fingers touching the trackpad. This doesn't
completely resolve the issue but does greatly mitigate it.
Signed-off-by: Clinton Sprain <clintonsprain@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use smoothed version of sensor array data to calculate movement and add
weight to prior values when calculating average. This gives more granular
and more predictable movement.
Signed-off-by: Clinton Sprain <clintonsprain@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds support for the GPIO buttons on some Intel Bay Trail
tablets originally running Windows 8. The ACPI description of these
buttons follows "Windows ACPI Design Guide for SoC Platforms".
Signed-off-by: Lejun Zhu <lejun.zhu@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"Some more updates for the input subsystem.
You will get a fix for race in mousedev that has been causing quite a
few oopses lately and a small fixup for force feedback support in
evdev"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: mousedev - fix race when creating mixed device
Input: don't modify the id of ioctl-provided ff effect on upload failure
The driver is only supported on DT enabled platforms. Convert the
driver to DT so that it can probe properly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver is only supported on DT enabled platforms. Convert the
driver to DT so that it can probe properly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver is only supported on DT enabled platforms. Convert the
driver to DT so that it can probe properly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the regmap APIs for this driver instead of custom pm8xxx
APIs. This breaks this driver's dependency on the pm8xxx APIs and
allows us to easily port it to other bus protocols in the future.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Simplify the error paths and reduce the lines of code in this
driver by using the devm_* APIs.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The gpio configuration in this driver doesn't work because the
gpio.h include doesn't exist. Remove the configuration as it
isn't strictly necessary, allowing us to actually compile this
driver. If it's needed in the future, it should be done via a
pinctrl driver.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds a new driver for keypad for Cirrus Logic CLPS711X CPUs.
Target CPU contain keyboard interface which can scan 8 column lines,
so we can read row GPIOs to read status and determine asserted state.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We should not be using static variable mousedev_mix in methods that can be
called before that singleton gets assigned. While at it let's add open and
close methods to mousedev structure so that we do not need to test if we
are dealing with multiplexor or normal device and simply call appropriate
method directly.
This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=71551
Reported-by: GiulioDP <depasquale.giulio@gmail.com>
Tested-by: GiulioDP <depasquale.giulio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If a new (id == -1) ff effect was uploaded from userspace,
ff-core.c::input_ff_upload() will have assigned a positive number to the
new effect id. Currently, evdev.c::evdev_do_ioctl() will save this new id
to userspace, regardless of whether the upload succeeded or not.
On upload failure, this can be confusing because the dev->ff->effects[]
array will not contain an element at the index of that new effect id.
This patch fixes this by leaving the id unchanged after upload fails.
Note: Unfortunately applications should still expect changed effect id for
quite some time.
This has been discussed on:
http://www.mail-archive.com/linux-input@vger.kernel.org/msg08513.html
("ff-core effect id handling in case of a failed effect upload")
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Elias Vanderstuyft <elias.vds@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem fixes from Dmitry Torokhov:
"Updates to Synaptics touchpad to better cope with devices in Lenovo
laptops, and a couple more fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - add manual min/max quirk for ThinkPad X240
Input: synaptics - add manual min/max quirk
Input: cypress_ps2 - don't report as a button pads
Input: da9052_onkey - use correct register bit for key status
Input: adp5588-keys - get value from data out when dir is out
There is a new firmware version for the EDT-FT5x06 chip.
Add support for detecting the firmware version and handle the
differences appropriately.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The FT5x06 datasheet specifies a minimum reset width of 5ms and a
delay between deassertion of reset and start of reporting of 300ms.
Adjust the delays to conform to the datasheet.
With the original delays I sometimes experienced communication
timeouts when initializing the controller.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This extends Benjamin Tissoires manual min/max quirk table with support for
the ThinkPad X240.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The new Lenovo Haswell series (-40's) contains a new Synaptics touchpad.
However, these new Synaptics devices report bad axis ranges.
Under Windows, it is not a problem because the Windows driver uses RMI4
over SMBus to talk to the device. Under Linux, we are using the PS/2
fallback interface and it occurs the reported ranges are wrong.
Of course, it would be too easy to have only one range for the whole
series, each touchpad seems to be calibrated in a different way.
We can not use SMBus to get the actual range because I suspect the firmware
will switch into the SMBus mode and stop talking through PS/2 (this is the
case for hybrid HID over I2C / PS/2 Synaptics touchpads).
So as a temporary solution (until RMI4 land into upstream), start a new
list of quirks with the min/max manually set.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
CC: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's dial back the default fuzz setting for most devices using this
driver, based on values from user feedback from forums and bug reports.
Signed-off-by: Clinton Sprain <clintonsprain@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The tnetv107x platform is getting removed, so the touchscreen
and keypad drivers for this platform will no longer be needed
either.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: linux-input@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
commit a1a7521064 moved to report EV_KEY event(KEY_POWER) instead of
reporting EV_PWR event(KEY_SUSPEND), but it didn't enable the capability, so
the KEY_POWER will not be reported to userspace by input core. this patch fixes
the issue.
Signed-off-by: Xianglong Du <Xianglong.Du@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The cypress PS/2 trackpad models supported by the cypress_ps2 driver
emulate BTN_RIGHT events in firmware based on the finger position, as part
of this no motion events are sent when the finger is in the button area.
The INPUT_PROP_BUTTONPAD property is there to indicate to userspace that
BTN_RIGHT events should be emulated in userspace, which is not necessary
in this case.
When INPUT_PROP_BUTTONPAD is advertised userspace will wait for a motion
event before propagating the button event higher up the stack, as it needs
current abs x + y data for its BTN_RIGHT emulation. Since in the
cypress_ps2 pads don't report motion events in the button area, this means
that clicks in the button area end up being ignored, so
INPUT_PROP_BUTTONPAD actually causes problems for these touchpads, and
removing it fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=76341
Reported-by: Adam Williamson <awilliam@redhat.com>
Tested-by: Adam Williamson <awilliam@redhat.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The wrong register bit of the DA9052/3 PMIC registers was
used to determine the status on the ONKEY.
Also a failure in reading the status register will no longer
result in the work queue being rescheduled as that would result
in a (potentially) endless retry.
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Acked-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Kconfig symbol X86_32 was introduced in October 2005, it's about time
to use it. This clears the last occurrence of the legacy
"X86 && !X86_64" construct :-)
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
I don't think the OLPC AP-SP driver is generally useful without OLPC
support. So make it depend on OLPC, unless build testing is enabled.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure that no callback is running before we teardown the module.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTCqL6AAoJEHm+PkMAQRiGljYIAICQIZsXmMc/pUC3hHgTr2KK
BBQXjnoE7tDN/QkZQzSj/+VqP1/Ndo7lQlXThXuooNhemjpmFCd8AIRhXi164NPE
NoAZ0efWu1kE3iAJKyHN11zVlv4NS0bsTlNAgPN0EwjDBTTk5thfiZBqNz56cWrZ
MqH8tKpUTuAPciXeyB6WI34pKMkzB+Urfoweum7euk8WyDw7kthpncwEt+fzBAKm
20+N2JVoHN7h2xuR4mx8rDXPbXlwPCH5K/8NapytbP7xWBJ3UaOjbbcKHbydrfkI
1eOlajXafFrjN/XTXDySqQg9lT6DoszOE0fhAZyrdPPqvbQOU64WdBcYyOg8ObI=
=KxaP
-----END PGP SIGNATURE-----
Merge tag 'v3.14-rc4' into next
Merge with Linux 3.14-rc4 to bring devm_request_any_context_irq().
The snd_soc_dapm_xxxx_pin all require the dapm_mutex to be held when
they are called as they edit the dirty list, however very few of the
callers do so.
This patch adds unlocked versions of all the functions replacing the
existing implementations with one that holds the lock internally. We
also fix up the places where the lock was actually held on the caller
side.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
snd_soc_dapm_sync takes the dapm_mutex internally, but we currently take
it externally as well. This patch fixes this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
This patch fix spelling typo in Documentation/DocBook.
It is because .html and .xml files are generated by make htmldocs,
I have to fix a typo within the source files.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=g6PN
-----END PGP SIGNATURE-----
Merge tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux into next/cleanup
This cleanup series gets rid of <mach/timex.h> for platforms not using
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
* tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux:
ARM: ixp4xx: fix timer latch calculation
ARM: drop <mach/timex.h> for !ARCH_MULTIPLATFORM, too
ARM: rpc: stop using <mach/timex.h>
ARM: ixp4xx: stop using <mach/timex.h>
input: ixp4xx-beeper: don't use symbols from <mach/timex.h>
ARM: at91: don't use <mach/timex.h>
ARM: ep93xx: stop using mach/timex.h
ARM: mmp: stop using mach/timex.h
ARM: netx: stop using mach/timex.h
ARM: sa1100: stop using mach/timex.h
clocksource: sirf/marco+prima2: drop usage of CLOCK_TICK_RATE
rtc: pxa: drop unused #define TIMER_FREQ
rtc: at91sam9: include <mach/hardware.h> explicitly
ARM/serial: at91: switch atmel serial to use gpiolib
Signed-off-by: Olof Johansson <olof@lixom.net>
No need to return a 'fake' return value on platform_get_irq() failure.
Just return the error code itself instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The wrong register bit of the DA9052/3 PMIC registers was
used to determine the status on the ONKEY.
Also a failure in reading the status register will no longer
result in the work queue being rescheduled as that would result
in a (potentially) endless retry.
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Acked-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change adds a delayed_work to detect the release of onkey since HW will
not generate interrupt for it.
At the same time, we move the KEY event to POWER instead of SUSPEND, which
will be suitable for both Android and Linux. Userspace PowerManager Daemon
will decide to suspend or shutdown based on how long we have touched onkey.
Signed-off-by: Xianglong Du <Xianglong.Du@csr.com>
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As discussed here: http://ez.analog.com/message/35852, the 5587 revC and
5588 revB spec sheets contain a mistake in the GPIO_DAT_STATx register
description.
According to R.Shnell at ADI, as well as my own observations, it should
read: "GPIO data status (shows GPIO state when read for inputs)".
This commit changes the get value function accordingly.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In resume entry, use dev_get_drvdata() instead of to_platform_device(dev) +
platform_get_drvdata(pdev).
Signed-off-by: Xianglong Du <Xianglong.Du@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This function lost namespace, this patch fixes it.
Signed-off-by: Xianglong Du <Xianglong.Du@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since the IRQ handler always returns IRQ_HANDLED it means this irq is not
a shared IRQ at all. Or at least, the SW is not self-consistent now.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We can control whetehr device generates interrupts or not so let's
implement open and close methods of input device so that we do not do any
processing until there are users.
Tested-by: Xianglong Du <Xianglong.Du@csr.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
New version of the PCU firmware supports two new commands:
- IMS_PCU_CMD_OFN_SET_CONFIG which allows to write data to the
registers of one finger navigation(OFN) chip present on the device
- IMS_PCU_CMD_OFN_GET_CONFIG which allows to read data form the
registers of said chip.
This commit adds two helper functions to use those commands and sysfs
attributes to use them. It also exposes some OFN configuration
parameters via sysfs.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We first create backlight and then input devices so we should destroy them
in opposite order when handling errors.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
uinput is used in the xorg-integration-tests suite and in the wayland
test suite. These automated tests suites create many virtual input
devices and then hook something to read these newly created devices.
Currently, uinput does not provide the created input device, which means
that we rely on an heuristic to guess which input node was created.
The problem is that is heuristic is subjected to races between different
uinput devices or even with physical devices. Having a way to retrieve
the sysfs path allows us to find without any doubts the event node.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rework dev_pm_qos_add_ancestor_request() so that device PM QoS type
is passed to it as the third argument and make it support the
DEV_PM_QOS_LATENCY_TOLERANCE device PM QoS type (in addition to
DEV_PM_QOS_RESUME_LATENCY).
That will allow the drivers of devices without latency tolerance
hardware support to use their ancestors having it as proxies for
their latency tolerance requirements.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Before we had the PWM framework we used to have a barebone PWM api. The
HAVE_PWM Kconfig symbol used to be selected by the PWM drivers to specify
the PWM API is present in the kernel. Since the last legacy driver is gone
the HAVE_PWM symbol can go aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-pwm@vger.kernel.orig
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The current implementation prevents us to add variable-length ioctl.
Use a bunch of gotos instead of break to allow us to do so.
No functional changes.
Signed-off-by: Benjamin Tisssoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This makes the zforce driver usable on devicetree-based platforms too.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bqreaders.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Devicetree support will be creating its own platfprm data structure that
is not attached to the device. Let's use the internal pointer to the
pdata instead of re-fetching it with dev_get_platdata().
Signed-off-by: Heiko Stuebner <heiko.stuebner@bqreaders.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A frame is a u8 array with the following structure:
[PAYLOAD_HEADER, PAYLOAD_LENGTH, ...PAYLOAD_BODY...]
PAYLOAD_BODY can be at most 255 bytes long, as it's size is represented
by PAYLOAD_LENGTH. Therefore we can reduce the stack memory allocated to
payload_buffer[] roughly by half, from 512 to 257 bytes.
Signed-off-by: Luis Ortega <luiorpe1@upv.es>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de> - bq Cervantes (imx6sl)
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The function zforce_read_packet() reads 2 values (bytes) of payload
header, validates them and then proceeds to read the payload body.
The function stores all these in a u8 buffer.
The PAYLOAD_LENGTH check seems to be trying to detect an overflow error.
However, since we are just reading a u8 value from the buffer, these
checks are unnecessary and we should simply compare against zero.
Signed-off-by: Luis Ortega <luiorpe1@upv.es>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de> - bq Cervantes (imx6sl)
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixed lines exceeding 80 characters long wherever possible,
as per the coding style.
Signed-off-by: Luis Ortega <luiorpe1@upv.es>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is usb_get_dev() in gtco_probe(), but there is no usb_put_dev()
anywhere in the driver.
As pointed out by Dmitry Torokhov:
The lifetime of gtco structure is already directly tied to lifetime of
usb_dev: when destroying usb_dev driver core will call remove() function
of currently bound driver (in our case gtco) which will destroy gtco
memory. Taking additional reference is not needed here.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds Fujitsu-Siemens AMILO Pro 8210 support to wistron_btns driver.
Functions are very similar to already supported AMILO Pro 3505, but 8210
has WIFI led.
Such functionality is needed to enable WiFi under Linux on 8210 when it
cold boots with hardware rfkill enabled, without booting another operating
system or running custom utility that calls appropriate BIOS function.
Signed-off-by: Jakub Bogusz <qboosh@pld-linux.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem updates from Dmitry Torokhov:
"Just a swath of driver fixes and cleanups, no new drivers this time
(although ALPS now supports one of the newer protocols, more to come)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
Input: wacom - add support for DTU-1031
Input: wacom - fix wacom->shared guards for dual input devices
Input: edt_ft5x06 - use devm_* functions where appropriate
Input: hyperv-keyboard - pass through 0xE1 prefix
Input: logips2pp - fix spelling s/reciver/receiver/
Input: delete non-required instances of include <linux/init.h>
Input: twl4030-keypad - convert to using managed resources
Input: twl6040-vibra - remove unneeded check for CONFIG_OF
Input: twl4030-keypad - add device tree support
Input: twl6040-vibra - add missing of_node_put
Input: twl4030-vibra - add missing of_node_put
Input: i8042 - cleanup SERIO_I8042 dependencies
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on x86
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on unicore32
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on sparc
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO for SH_CAYMAN
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on powerpc
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on mips
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on IA64
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on ARM/Footbridge
...
- ACPI core changes to make it create a struct acpi_device object for every
device represented in the ACPI tables during all namespace scans regardless
of the current status of that device. In accordance with this, ACPI hotplug
operations will not delete those objects, unless the underlying ACPI tables
go away.
- On top of the above, new sysfs attribute for ACPI device objects allowing
user space to check device status by triggering the execution of _STA for
its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating the
PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the code
"glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for the
DBG2 and PCCT tables to ACPICA, fixes some bugs and improves debug
facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization earlier.
That should allow us to use ACPI during the timekeeping initialization
and possibly to simplify the EFI initialization too. From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over from
Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in drivers
that uses _DSM to execute it via the new helper. From Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun Guo,
Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava, Rashika Kheria,
Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support, from
Dirk Brandewie and intel_pstate documentation from Ramkumar Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John Tobias,
Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC disabled
during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente Kurusa,
Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a cpupower
tool cleanup from One Thousand Gnomes.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=dRf6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"As far as the number of commits goes, the top spot belongs to ACPI
this time with cpufreq in the second position and a handful of PM
core, PNP and cpuidle updates. They are fixes and cleanups mostly, as
usual, with a couple of new features in the mix.
The most visible change is probably that we will create struct
acpi_device objects (visible in sysfs) for all devices represented in
the ACPI tables regardless of their status and there will be a new
sysfs attribute under those objects allowing user space to check that
status via _STA.
Consequently, ACPI device eject or generally hot-removal will not
delete those objects, unless the table containing the corresponding
namespace nodes is unloaded, which is extremely rare. Also ACPI
container hotplug will be handled quite a bit differently and cpufreq
will support CPU boost ("turbo") generically and not only in the
acpi-cpufreq driver.
Specifics:
- ACPI core changes to make it create a struct acpi_device object for
every device represented in the ACPI tables during all namespace
scans regardless of the current status of that device. In
accordance with this, ACPI hotplug operations will not delete those
objects, unless the underlying ACPI tables go away.
- On top of the above, new sysfs attribute for ACPI device objects
allowing user space to check device status by triggering the
execution of _STA for its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating
the PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the
code "glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for
the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves
debug facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization
earlier. That should allow us to use ACPI during the timekeeping
initialization and possibly to simplify the EFI initialization too.
From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over
from Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in
drivers that uses _DSM to execute it via the new helper. From
Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun
Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava,
Rashika Kheria, Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support,
from Dirk Brandewie and intel_pstate documentation from Ramkumar
Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz
Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark
Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John
Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh
Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC
disabled during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf
Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente
Kurusa, Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a
cpupower tool cleanup from One Thousand Gnomes"
* tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
platform: introduce OF style 'modalias' support for platform bus
PM / tools: new tool for suspend/resume performance optimization
ACPI: fix module autoloading for ACPI enumerated devices
ACPI: add module autoloading support for ACPI enumerated devices
ACPI: fix create_modalias() return value handling
...
This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep it
strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared with Mike
Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for multiplatform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3CcT
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep
it strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared
with Mike Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for
multiplatform"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
...
Pull ARM updates from Russell King:
"In this set, we have:
- Refactoring of some of the old StrongARM-1100 GPIO code to make
things simpler by Dmitry Eremin-Solenikov
- Read-only and non-executable support for modules on ARM from Laura
Abbot
- Removal of unnecessary set_drvdata() calls in AMBA code
- Some non-executable support for kernel lowmem mappings at the 1MB
section granularity, and dumping of kernel page tables via debugfs
- Some improvements for the timer/clock code on Footbridge platforms,
and cleanup some of the LED code there
- Fix fls/ffs() signatures to match x86 to prevent build warnings,
particularly where these are used with min/max() macros
- Avoid using the bootmem allocator on ARM (patches from Santosh
Shilimkar)
- Various asid/unaligned access updates from Will Deacon"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (51 commits)
ARM: SMP implementations are not supposed to return from smp_ops.cpu_die()
ARM: ignore memory below PHYS_OFFSET
Fix select-induced Kconfig warning for ZBOOT_ROM
ARM: fix ffs/fls implementations to match x86
ARM: 7935/1: sa1100: collie: add gpio-keys configuration
ARM: 7932/1: bcm: Add DEBUG_LL console support
ARM: 7929/1: Remove duplicate SCHED_HRTICK config option
ARM: 7928/1: kconfig: select HAVE_EFFICIENT_UNALIGNED_ACCESS for CPUv6+ && MMU
ARM: 7927/1: dcache: select DCACHE_WORD_ACCESS for big-endian CPUs
ARM: 7926/1: mm: flesh out and fix the comments in the ASID allocator
ARM: 7925/1: mm: keep track of last ASID allocation to improve bitmap searching
ARM: 7924/1: mm: don't bother with reserved ttbr0 when running with LPAE
ARM: PCI: add legacy IDE IRQ implementation
ARM: footbridge: cleanup LEDs code
ARM: pgd allocation: retry on failure
ARM: footbridge: add one-shot mode for DC21285 timer
ARM: footbridge: add sched_clock implementation
ARM: 7922/1: l2x0: add Marvell Tauros3 support
ARM: 7877/1: use built-in byte swap function
ARM: 7921/1: mcpm: remove redundant dsb instructions prior to sev
...
- FIFO event channels. Key advantages: support for over 100,000 events (2^17),
16 different event priorities, improved fairness in event latency through
the use of FIFOs.
- Xen PVH support. "It’s a fully PV kernel mode, running with paravirtualized
disk and network, paravirtualized interrupts and timers, no emulated devices
of any kind (and thus no qemu), no BIOS or legacy boot — but instead of
requiring PV MMU, it uses the HVM hardware extensions to virtualize the
pagetables, as well as system calls and other privileged operations."
(from "The Paravirtualization Spectrum, Part 2: From poles to a spectrum")
Bug-fixes:
- Fixes in balloon driver (refactor and make it work under ARM)
- Allow xenfb to be used in HVM guests.
- Allow xen_platform_pci=0 to work properly.
- Refactors in event channels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJS4BmLAAoJEFjIrFwIi8fJ4SAH/iNGESowgMhfW64vRA8pBWq+
NRJpUjYjjwmbxpwoNl6NPwn15cIXFyc3sMtvvrDD3taRDyko2RFuT+NTjpO05xPh
d/cRpRXpXERHoiFgPf/WTp7ONBDhvPtHG0+BzJKwgqEIOUYXdbhD+gEjaVlFJScS
CAY68OLmk7XYMSZBNzPfKNbSCyhVgZF7wpaimK9lxZBKsFRCDIq6jIyrAsC8epIL
6V/V4l2S6lk/uUeGB6ULphYeINjI2kkpbSfCd1vyenLfWpVscc2o8uWEYFcZMAxy
V4HpsoseuqrfdDqgPfud3VgogdISvbkCvDfW85rzfDP4MWxei2mVHFtJ/gSBV+g=
=ToNG
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.14-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen updates from Konrad Rzeszutek Wilk:
"Two major features that Xen community is excited about:
The first is event channel scalability by David Vrabel - we switch
over from an two-level per-cpu bitmap of events (IRQs) - to an FIFO
queue with priorities. This lets us be able to handle more events,
have lower latency, and better scalability. Good stuff.
The other is PVH by Mukesh Rathor. In short, PV is a mode where the
kernel lets the hypervisor program page-tables, segments, etc. With
EPT/NPT capabilities in current processors, the overhead of doing this
in an HVM (Hardware Virtual Machine) container is much lower than the
hypervisor doing it for us.
In short we let a PV guest run without doing page-table, segment,
syscall, etc updates through the hypervisor - instead it is all done
within the guest container. It is a "hybrid" PV - hence the 'PVH'
name - a PV guest within an HVM container.
The major benefits are less code to deal with - for example we only
use one function from the the pv_mmu_ops (which has 39 function
calls); faster performance for syscall (no context switches into the
hypervisor); less traps on various operations; etc.
It is still being baked - the ABI is not yet set in stone. But it is
pretty awesome and we are excited about it.
Lastly, there are some changes to ARM code - you should get a simple
conflict which has been resolved in #linux-next.
In short, this pull has awesome features.
Features:
- FIFO event channels. Key advantages: support for over 100,000
events (2^17), 16 different event priorities, improved fairness in
event latency through the use of FIFOs.
- Xen PVH support. "It’s a fully PV kernel mode, running with
paravirtualized disk and network, paravirtualized interrupts and
timers, no emulated devices of any kind (and thus no qemu), no BIOS
or legacy boot — but instead of requiring PV MMU, it uses the HVM
hardware extensions to virtualize the pagetables, as well as system
calls and other privileged operations." (from "The
Paravirtualization Spectrum, Part 2: From poles to a spectrum")
Bug-fixes:
- Fixes in balloon driver (refactor and make it work under ARM)
- Allow xenfb to be used in HVM guests.
- Allow xen_platform_pci=0 to work properly.
- Refactors in event channels"
* tag 'stable/for-linus-3.14-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (52 commits)
xen/pvh: Set X86_CR0_WP and others in CR0 (v2)
MAINTAINERS: add git repository for Xen
xen/pvh: Use 'depend' instead of 'select'.
xen: delete new instances of __cpuinit usage
xen/fb: allow xenfb initialization for hvm guests
xen/evtchn_fifo: fix error return code in evtchn_fifo_setup()
xen-platform: fix error return code in platform_pci_init()
xen/pvh: remove duplicated include from enlighten.c
xen/pvh: Fix compile issues with xen_pvh_domain()
xen: Use dev_is_pci() to check whether it is pci device
xen/grant-table: Force to use v1 of grants.
xen/pvh: Support ParaVirtualized Hardware extensions (v3).
xen/pvh: Piggyback on PVHVM XenBus.
xen/pvh: Piggyback on PVHVM for grant driver (v4)
xen/grant: Implement an grant frame array struct (v3).
xen/grant-table: Refactor gnttab_init
xen/grants: Remove gnttab_max_grant_frames dependency on gnttab_init.
xen/pvh: Piggyback on PVHVM for event channels (v2)
xen/pvh: Update E820 to work with PVH (v2)
xen/pvh: Secondary VCPU bringup (non-bootup CPUs)
...
New drivers
- Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and Battery Charger
- TI/National Semiconductor LP3943 I2C GPIO Expander and PWM Generator
Existing driver adaptions
- Expansion of Wolfson Arizona DSP and High-Pass filter controls
- TI TWL6040 default Regmap support and Regcache addition/bypass
- Some nice Smatch catch fixes
- Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
- ChromeOS EC timing (delay) adaptions and added dependency on OF
- Many constifications of 'struct {mfd_cell,regmap_irq,et. al}'
- Watchdog support added for NVIDIA AS3722
- Convert functions to static in TI AM335x
- Realigned previously defeated functionality in TI AM335x
- IIO ADC-TSC concurrency dead-lock/timeout resolution
- Addition of Power Management and Clock support for Samsung core
- DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
- Greater use of irqdomain functionality in ST-E AB8500
- Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
- Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
- Device Tree documentation added for TI/Nat Semi LP3943
- Version detection and voltage tables for TI TPS6586x PMIC devices
- Simplification of Freescale MC13XXX (de-)initialisation routines
- Clean-up and simplification of the Realtek parent driver
- Added support for RTL8402 Realtek PCI-Express card reader
- Resource leak fix for Maxim 77686
- Possible suspend BUG() fix in OMAP USB TLL
- Support for new Wolfson WM5110 Revision (D)
- Testing of automatic assignment of of_node in mfd_add_device()
- Reversion of the above when it started to cause issues
- Remove legacy Platform Data from;
TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
- Clean-ups; tabbing issues, function name changes, 'drvdata = NULL' removal,
unused uninitialised warning mitigation, error message clarity,
removal of redundant/duplicate checks, licensing (GPL -> GPL2),
coding consistency, duplicate function declaration, ret checks,
commit corrections, redundant of_match_ptr() helper removal,
spelling, #if-deffery removal and header guards name changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=PuTE
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd
Pull MFD changes from Lee Jones:
"New drivers
- Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and
Battery Charger
- TI/National Semiconductor LP3943 I2C GPIO Expander and PWM
Generator
Existing driver adaptions
- Expansion of Wolfson Arizona DSP and High-Pass filter controls
- TI TWL6040 default Regmap support and Regcache addition/bypass
- Some nice Smatch catch fixes
- Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
- ChromeOS EC timing (delay) adaptions and added dependency on OF
- Many constifications of 'struct {mfd_cell,regmap_irq,et.al}'
- Watchdog support added for NVIDIA AS3722
- Convert functions to static in TI AM335x
- Realigned previously defeated functionality in TI AM335x
- IIO ADC-TSC concurrency dead-lock/timeout resolution
- Addition of Power Management and Clock support for Samsung core
- DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
- Greater use of irqdomain functionality in ST-E AB8500
- Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
- Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
- Device Tree documentation added for TI/Nat Semi LP3943
- Version detection and voltage tables for TI TPS6586x PMIC devices
- Simplification of Freescale MC13XXX (de-)initialisation routines
- Clean-up and simplification of the Realtek parent driver
- Added support for RTL8402 Realtek PCI-Express card reader
- Resource leak fix for Maxim 77686
- Possible suspend BUG() fix in OMAP USB TLL
- Support for new Wolfson WM5110 Revision (D)
- Testing of automatic assignment of of_node in mfd_add_device()
- Reversion of the above when it started to cause issues
- Remove legacy Platform Data from;
TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
- Clean-ups; tabbing issues, function name changes, 'drvdata = NULL'
removal, unused uninitialised warning mitigation, error
message clarity, removal of redundant/duplicate checks,
licensing (GPL -> GPL2), coding consistency, duplicate
function declaration, ret checks, commit corrections,
redundant of_match_ptr() helper removal, spelling,
#if-deffery removal and header guards name changes"
* tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd: (78 commits)
mfd: wm5110: Add register patch for rev D chip
mfd: omap-usb-tll: Don't hold lock during pm_runtime_get/put_sync()
gpio: lp3943: Remove redundant of_match_ptr helper
mfd: sta2x11-mfd: Use named constants for pci_power_t values
Documentation: mfd: Fix LDO index in s2mps11.txt
mfd: Cleanup mfd-mcp-sa11x0.h header
mfd: max8997: Use "IS_ENABLED(CONFIG_OF)" for DT code.
mfd: twl6030: Fix endianness problem in IRQ handler
mfd: sec-core: Add cells for S5M8767-clocks
mfd: max14577: Remove redundant of_match_ptr helper
mfd: twl6040: Fix sparse non static symbol warning
mfd: Revert "mfd: Always assign of_node in mfd_add_device()"
mfd: rtsx: Fix sparse non static symbol warning
mfd: max77693: Set proper maximum register for MUIC regmap
mfd: max77686: Fix regmap resource leak on driver remove
mfd: Represent correct filenames in file headers
mfd: rtsx: Add support for card reader rtl8402
mfd: rtsx: Add set pull control macro and simplify rtl8411
mfd: max8997: Enforce mfd_add_devices() return value check
mfd: mc13xxx: Simplify probe() & remove()
...
Symbol MFD_MC13783 always selected by MFD_MC13XXX, so no need
to keep additional symbol.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
features->quirks can have multiple bits set. For dual input, we only
need to check WACOM_QUIRK_MULTI_INPUT.
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Simplify the error path and remove() function by using devm_*
functions for requesting gpios and irq and allocating the input
device.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Here's the big tty/serial driver pull request for 3.14-rc1
There are a number of n_tty fixes and cleanups, and some serial driver
bugfixes, and we got rid of one obsolete driver, making this series
remove more lines than added, always a nice surprise.
All of these have been in linux-next with no reports of issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlLdiiAACgkQMUfUDdst+ymInACgu+gjm0q6sua8Zsk9HN3Ko0jK
Zy0AoI7jieqSxZfvZD84US98HTiWtumH
=z6GV
-----END PGP SIGNATURE-----
Merge tag 'tty-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the big tty/serial driver pull request for 3.14-rc1
There are a number of n_tty fixes and cleanups, and some serial driver
bugfixes, and we got rid of one obsolete driver, making this series
remove more lines than added, always a nice surprise.
All of these have been in linux-next with no reports of issues"
* tag 'tty-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (60 commits)
tty/serial: at91: disable uart timer at start of shutdown
serial: 8250: enable UART_BUG_NOMSR for Tegra
tty/serial: at91: reset rx_ring when port is shutdown
tty/serial: at91: fix race condition in atmel_serial_remove
tty/serial: at91: Handle shutdown more safely
serial: sirf: correct condition for fetching dma buffer into tty
serial: sirf: provide pm entries of uart_ops
serial: sirf: use PM macro initialize PM functions
serial: clps711x: Enable driver compilation with COMPILE_TEST
serial: clps711x: Add support for N_IRDA line discipline
tty: synclink: avoid sleep_on race
tty/amiserial: avoid interruptible_sleep_on
tty: delete non-required instances of include <linux/init.h>
tty: an overflow of multiplication in drivers/tty/cyclades.c
serial: Remove old SC26XX driver
serial: add support for 200 v3 series Titan card
serial: 8250: Fix initialisation of Quatech cards with the AMCC PCI chip
tty: Removing the deprecated function tty_vhangup_locked()
TTY/n_gsm: Removing the wrong tty_unlock/lock() in gsm_dlci_release()
tty/serial: at91: document clock properties
...
* acpi-cleanup: (22 commits)
ACPI / tables: Return proper error codes from acpi_table_parse() and fix comment.
ACPI / tables: Check if id is NULL in acpi_table_parse()
ACPI / proc: Include appropriate header file in proc.c
ACPI / EC: Remove unused functions and add prototype declaration in internal.h
ACPI / dock: Include appropriate header file in dock.c
ACPI / PCI: Include appropriate header file in pci_link.c
ACPI / PCI: Include appropriate header file in pci_slot.c
ACPI / EC: Mark the function acpi_ec_add_debugfs() as static in ec_sys.c
ACPI / NVS: Include appropriate header file in nvs.c
ACPI / OSL: Mark the function acpi_table_checksum() as static
ACPI / processor: initialize a variable to silence compiler warning
ACPI / processor: use ACPI_COMPANION() to get ACPI device
ACPI: correct minor typos
ACPI / sleep: Drop redundant acpi_disabled check
ACPI / dock: Drop redundant acpi_disabled check
ACPI / table: Replace '1' with specific error return values
ACPI: remove trailing whitespace
ACPI / IBFT: Fix incorrect <acpi/acpi.h> inclusion in iSCSI boot firmware module
ACPI / i915: Fix incorrect <acpi/acpi.h> inclusions via <linux/acpi_io.h>
SFI / ACPI: Fix warnings reported during builds with W=1
...
Conflicts:
drivers/acpi/nvs.c
drivers/hwmon/asus_atk0110.c
Pass through the 0xE1 prefix so atkbd can properly parse the scancode
data.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The purpose of reg_se_cache has been defeated. It should avoid the
read-back of the register to avoid the latency and the fact that the
bits are reset to 0 after the individual conversation took place.
The reason why this is required like this to work, is that read-back of
the register removes the bits of the ADC so they do not start another
conversation after the register is re-written from the TSC side for the
update.
To avoid the not required read-back I introduce a "set once" variant which
does not update the cache mask. After the conversation completes, the
bit is removed from the SE register anyway and we don't plan a new
conversation "any time soon". The current set function is renamed to
set_cache to distinguish the two operations.
This is a small preparation for a larger sync-rework.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since the driver requires DT now we do not need to check if CONFIG_OF is
defined.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add device tree support for twl4030 keypad driver.
Tested on Nokia N900.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We should drop reference to twl6040_core_node device_node once we are done
using it.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We should drop reference to twl6040_core_node device_node once we are done
using it.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The user has the option of disabling the platform driver:
00:02.0 Unassigned class [ff80]: XenSource, Inc. Xen Platform Device (rev 01)
which is used to unplug the emulated drivers (IDE, Realtek 8169, etc)
and allow the PV drivers to take over. If the user wishes
to disable that they can set:
xen_platform_pci=0
(in the guest config file)
or
xen_emul_unplug=never
(on the Linux command line)
except it does not work properly. The PV drivers still try to
load and since the Xen platform driver is not run - and it
has not initialized the grant tables, most of the PV drivers
stumble upon:
input: Xen Virtual Keyboard as /devices/virtual/input/input5
input: Xen Virtual Pointer as /devices/virtual/input/input6M
------------[ cut here ]------------
kernel BUG at /home/konrad/ssd/konrad/linux/drivers/xen/grant-table.c:1206!
invalid opcode: 0000 [#1] SMP
Modules linked in: xen_kbdfront(+) xenfs xen_privcmd
CPU: 6 PID: 1389 Comm: modprobe Not tainted 3.13.0-rc1upstream-00021-ga6c892b-dirty #1
Hardware name: Xen HVM domU, BIOS 4.4-unstable 11/26/2013
RIP: 0010:[<ffffffff813ddc40>] [<ffffffff813ddc40>] get_free_entries+0x2e0/0x300
Call Trace:
[<ffffffff8150d9a3>] ? evdev_connect+0x1e3/0x240
[<ffffffff813ddd0e>] gnttab_grant_foreign_access+0x2e/0x70
[<ffffffffa0010081>] xenkbd_connect_backend+0x41/0x290 [xen_kbdfront]
[<ffffffffa0010a12>] xenkbd_probe+0x2f2/0x324 [xen_kbdfront]
[<ffffffff813e5757>] xenbus_dev_probe+0x77/0x130
[<ffffffff813e7217>] xenbus_frontend_dev_probe+0x47/0x50
[<ffffffff8145e9a9>] driver_probe_device+0x89/0x230
[<ffffffff8145ebeb>] __driver_attach+0x9b/0xa0
[<ffffffff8145eb50>] ? driver_probe_device+0x230/0x230
[<ffffffff8145eb50>] ? driver_probe_device+0x230/0x230
[<ffffffff8145cf1c>] bus_for_each_dev+0x8c/0xb0
[<ffffffff8145e7d9>] driver_attach+0x19/0x20
[<ffffffff8145e260>] bus_add_driver+0x1a0/0x220
[<ffffffff8145f1ff>] driver_register+0x5f/0xf0
[<ffffffff813e55c5>] xenbus_register_driver_common+0x15/0x20
[<ffffffff813e76b3>] xenbus_register_frontend+0x23/0x40
[<ffffffffa0015000>] ? 0xffffffffa0014fff
[<ffffffffa001502b>] xenkbd_init+0x2b/0x1000 [xen_kbdfront]
[<ffffffff81002049>] do_one_initcall+0x49/0x170
.. snip..
which is hardly nice. This patch fixes this by having each
PV driver check for:
- if running in PV, then it is fine to execute (as that is their
native environment).
- if running in HVM, check if user wanted 'xen_emul_unplug=never',
in which case bail out and don't load any PV drivers.
- if running in HVM, and if PCI device 5853:0001 (xen_platform_pci)
does not exist, then bail out and not load PV drivers.
- (v2) if running in HVM, and if the user wanted 'xen_emul_unplug=ide-disks',
then bail out for all PV devices _except_ the block one.
Ditto for the network one ('nics').
- (v2) if running in HVM, and if the user wanted 'xen_emul_unplug=unnecessary'
then load block PV driver, and also setup the legacy IDE paths.
In (v3) make it actually load PV drivers.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it
Reported-by: Anthony PERARD <anthony.perard@citrix.com>
Reported-and-Tested-by: Fabio Fantoni <fabio.fantoni@m2r.biz>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[v2: Add extra logic to handle the myrid ways 'xen_emul_unplug'
can be used per Ian and Stefano suggestion]
[v3: Make the unnecessary case work properly]
[v4: s/disks/ide-disks/ spotted by Fabio]
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> [for PCI parts]
CC: stable@vger.kernel.org
Remove messy dependencies from SERIO_I8042 by having it depend on one
Kconfig symbol (ARCH_MIGHT_HAVE_PC_SERIO) and having architectures
which need it select ARCH_MIGHT_HAVE_PC_SERIO in arch/*/Kconfig.
New architectures are unlikely to need SERIO_I8042, so this avoids
having an ever growing list of architectures to exclude.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This enables the rumble force feedback on the F710 unit since
it is no longer treated as XTYPE_UNKNOWN type.
Signed-off-by: Petr Sebor <petr@scssoft.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When using Razer Onza controller the dpad doesn't work in many games
because D-PAD was mapped to buttons (useful for dance pads) and not to
HAT0X/Y axis.
ers who really want to have it mapped to buttons can restore previous
behavior by using 'dpad_to_buttons' module option.
Signed-off-by: Thomaz de Oliveira dos Reis <thor27@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We need to make sure we allocate absinfo data when we are setting one of
EV_ABS/ABS_XXX capabilities, otherwise we may bomb when we try to emit this
event.
Rested-by: Paul Cercueil <pcercuei@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver can't deal with two entries its keymap having the same keycode.
When this happens it will get confused about whether the key is down or up
and will cause some screwy behavior.
We need to have two entries for KEY_BACKSLASH to handle US and UK
keyboards. Specifically:
* On the US keyboard the backslash key (above enter) is r3 c11 and is
supposed to be reported as BACKSLASH.
* On the UK keyboard the # key (left of enter) is r4 c10 and is
supposed to be reported as BACKSLASH.
* On the UK keyboard the \ key (left of Z) is r2 c7 and is supposed to
be reported as KEY_102ND.
Note that both keyboards (US and UK) have only one physical backslash
key so the constraint that each physical key should have its own keycode
still stands.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Driver core clears the driver data to NULL after device_release
or on probe failure, so just remove it from here.
Driver core change:
"device-core: Ensure drvdata = NULL when no driver is bound"
(sha1: 0998d06310)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
free_irq() in the error handling case is missing when change
pass input device directly to interrupt.
Fixes: b27f8fee4965('Input: pmic8xxx-pwrkey - pass input device directly to interrupt')
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds support for another flavor of ALPS protocol used in newer
"Dolphin" devices.
Signed-off-by: Yunkang Tang <yunkang.tang@cn.alps.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8T7+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
From Stephen Warren:
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
* tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (30 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
mach/timex.h is about to be dropped so don't use symbols defined in
there. For ixp4xx there is a suitable substitute for IXP4XX_TIMER_FREQ,
i.e. a global and exported variable that holds the same value.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The error code was not set if unable to set config, so the error
condition wasn't reflected in the return value. Fix to return a
negative error code from the error handling case instead of 0.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current assumption in the elantech driver that hw version 3 touchpads
are never clickpads and hw version 4 touchpads are always clickpads is
wrong.
There are several bug reports for this, ie:
https://bugzilla.redhat.com/show_bug.cgi?id=1030802http://superuser.com/questions/619582/right-elantech-touchpad-button-not-working-in-linux
I've spend a couple of hours wading through various bugzillas, launchpads
and forum posts to create a list of fw-versions and capabilities for
different laptop models to find a good method to differentiate between
clickpads and versions with separate hardware buttons.
Which shows that a device being a clickpad is reliable indicated by bit 12
being set in the fw_version. I've included the gathered list inside the
driver, so that we've this info at hand if we need to revisit this later.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When waking up the platform by pressing a specific key, sending a
release on that key makes it impossible to react on the event in
user-space. This is fixed by moving the input_reset_device() call to
resume instead.
[dmitry.torokhov@gmail.com: make sure we still restore LED/sound state
after resume, handle hibernation properly]
Signed-off-by: Aleksej Makarov <aleksej.makarov@sonymobile.com>
Signed-off-by: Oskar Andero <oskar.andero@sonymobile.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Simplify the code and create mandatory 'name' attribute by using
new hwmon API.
Also use is_visible to determine visible attributes instead of creating
several different attribute groups.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
New Intuos series models added a hardware switch to turn touch
data on/off. The state of the switch is reported periodically
from the tablet. To report the state the driver will emit SW_MUTE_DEVICE
events.
Reviewed_by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSrhGrAAoJEHm+PkMAQRiGsNoH/jIK3CsQ2lbW7yRLXmfgtbzz
i2Kep6D4SDvmaLpLYOVC8xNYTiE8jtTbSXHomwP5wMZ63MQDhBfnEWsEWqeZ9+D9
3Q46p0QWuoBgYu2VGkoxTfygkT6hhSpwWIi3SeImbY4fg57OHiUil/+YGhORM4Qc
K4549OCTY3sIrgmWL77gzqjRUo+pQ4C73NKqZ3+5nlOmYBZC1yugk8mFwEpQkwhK
4NRNU760Fo+XIht/bINqRiPMddzC15p0mxvJy3cDW8bZa1tFSS9SB7AQUULBbcHL
+2dFlFOEb5SV1sNiNPrJ0W+h2qUh2e7kPB0F8epaBppgbwVdyQoC2u4uuLV2ZN0=
=lI2r
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc4' into next
Synchronize with mainline to bring in the new keycode definitions and
new hwmon API.
Use the regmap APIs for this driver instead of custom pm8xxx
APIs. This breaks this driver's dependency on the pm8xxx APIs and
allows us to easily port it to other bus protocols in the future.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of passing the pointer to the container structure just
pass the input device here. This saves a dereference in the fast
path.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the regmap APIs for this driver instead of custom pm8xxx
APIs. This breaks this driver's dependency on the pm8xxx APIs and
allows us to easily port it to other bus protocols in the future.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Simplify the error paths and reduce the lines of code in this
driver by using the devm_* APIs.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Include cyttsp4_core.h in cyttsp_i2c_common.c to ensure that implementation
of cyttsp_i2c_read_block_data() and cyttsp_i2c_write_block_data()
match what the rest of the driver expects.
Thus, it also eliminates the following warning in cyttsp_i2c_common.c:
drivers/input/touchscreen/cyttsp_i2c_common.c:34:5: warning: no previous prototype for ‘cyttsp_i2c_read_block_data’ [-Wmissing-prototypes]
drivers/input/touchscreen/cyttsp_i2c_common.c:64:5: warning: no previous prototype for ‘cyttsp_i2c_write_block_data’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
handle_level_irq masks the interrupt before handling it, and only
unmasks it after the handler is finished. So when a touch event
happens after threads are suspended, but before the system is fully asleep
the irq handler tries to wakeup the thread which will only happen on the
next resume, resulting in the wakeup event never being sent and the driver
not being able to wake the system from sleep due to the masked irq.
Therefore move the wakeup_event to a small non-threaded handler.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Restore previous layout of sysfs attributes that was broken by commit
3778a2129b (input: serio: remove bus usage of
dev_attrs) which moved all serio device attributes into 'id' group, when
only 'type', 'proto', 'id', and 'extra' should be in 'id' group and the
rest of attributes should be attached directly to the device.
Reported-by: Thomas Hellstrom <thellstrom@vmware.com>
Tested-by: Thomas Hellstrom <thellstrom@vmware.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSogqUAAoJEHm+PkMAQRiGM2MIAJrr5KEXEWuuAR4+JkkWBK7A
+dVT4n1MM4wP/aCIyriSlq7kgT03Wxk4Q4wKsj2wZvDQkNgEQjrctgIihc75jqi5
126nmT3YXJLwgDpFA3RHZUWve3j3vfUG53rRuk7K9Xx1sGWU3Ls7BuInvQZ//+QS
6UB4UuEAalmose5U8ToXQfMqZhjwreZKeb64TEZwFvu2klv4cnka1L/zHbmQGgRg
2Pfv+aUrjsYE8s9lkEKX8MIQsDn28Q5Lsv7XIEQwo2at4rYbJaxX6usuC1OI0MQ5
BLUn1GgtvOidq6FzSg6kXiA/MJYH3J0S+p4uULWAprxA+KeJRbWNRroM94W1qAk=
=1Wcq
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc3' into for-linus
Merging with the mainline to sync up on changes to serio core.
Most line disciplines already handle the undocumented NULL flag
ptr in their .receive_buf method; however, several don't.
Document the NULL flag ptr, and correct handling in the
N_MOUSE, N_GSM0710 and N_R394 line disciplines.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should be able to override firmware-provided parameters with in-kernel
data, if needed. To that effect favor platform data, if present, over
devicetree data.
Acked-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Nick Dyer