When doing a modeset where the sink is transitioning from D3 to D0 , it
would sometimes be possible for the initial power_up_phy() to start
timing out. This would only be observed in the last action before the
sink went into D3 mode was intel_dp_sink_dpms(DRM_MODE_DPMS_OFF). We
originally thought this might be an issue with us accidentally shutting
off the aux block when putting the sink into D3, but since the DP spec
mandates that sinks must wake up within 1ms while we have 100ms to
respond to an ESI irq, this didn't really add up. Turns out that the
problem is more subtle then that:
It turns out that the timeout is from us not enabling DPMS on the MST
hub before actually trying to initiate sideband communications. This
would cause the first sideband communication (power_up_phy()), to start
timing out because the sink wasn't ready to respond. Afterwards, we
would call intel_dp_sink_dpms(DRM_MODE_DPMS_ON) in
intel_ddi_pre_enable_dp(), which would actually result in waking up the
sink so that sideband requests would work again.
Since DPMS is what lets us actually bring the hub up into a state where
sideband communications become functional again, we just need to make
sure to enable DPMS on the display before attempting to perform sideband
communications.
Changes since v1:
- Remove comment above if (!intel_dp->is_mst) - vsryjala
- Move intel_dp_sink_dpms() for MST into intel_dp_post_disable_mst() to
keep enable/disable paths symmetrical
- Improve commit message - dhnkrn
Changes since v2:
- Only send DPMS off when we're disabling the last sink, and only send
DPMS on when we're enabling the first sink - dhnkrn
Changes since v3:
- Check against is_mst, not intel_dp->is_mst - dhnkrn/vsyrjala
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Cc: stable@vger.kernel.org
Fixes: ad260ab32a ("drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.")
Link: https://patchwork.freedesktop.org/patch/msgid/20180407011053.22437-1-lyude@redhat.com
Currently, we rely on inspecting the hangcheck state from within the
i915_reset() routines to determine which engines were guilty of the
hang. This is problematic for cases where we want to run
i915_handle_error() and call i915_reset() independently of hangcheck.
Instead of relying on the indirect parameter passing, turn it into an
explicit parameter providing the set of stalled engines which then are
treated as guilty until proven innocent.
While we are removing the implicit stalled parameter, also make the
reason into an explicit parameter to i915_reset(). We still need a
back-channel for i915_handle_error() to hand over the task to the locked
waiter, but let's keep that its own channel rather than incriminate
another.
This leaves stalled/seqno as being private to hangcheck, with no more
nefarious snooping by reset, be it whole-device or per-engine. \o/
The only real issue now is that this makes it crystal clear that we
don't actually do any testing of hangcheck per se in
drv_selftest/live_hangcheck, merely of resets!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180406220354.18911-2-chris@chris-wilson.co.uk
If we are resetting just one engine, we know it has stalled. So we can
pass the stalled parameter directly to i915_gem_reset_engine(), which
alleviates the necessity to poke at the generic engine->hangcheck.stalled
magic variable, leaving that under control of hangcheck as its name
implies. Other than simplifying by removing the indirect parameter along
this path, this allows us to introduce new reset mechanisms that run
independently of hangcheck.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180406220354.18911-1-chris@chris-wilson.co.uk
We will want to park GEM before disengaging the drive^W^W^W unwedging.
Since we already do the work for idling, expose the guts as a new
function that we can then reuse.
v2: Just skip if already parked; makes it more forgiving to use by
future callers.
v3: Extract mark_busy, rename it to i915_gem_unpark and place it next to
i915_gem_park so that we can evaluate it for symmetry more easily.
Calling GEM from inside i915_request looks to be a bit of a layering
violation, for the moment I am imaging them as being notify_cb.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> #v1
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180406155144.27791-1-chris@chris-wilson.co.uk
Tvrtko mentioned that wait_for_hang() was confusing as it does not
actually wait for the aforementioned hang, just until the request is
running and we are *ready* to inject a hang. A quick
s/wait_for_hang/wait_until_running/ removes that confusion without
having to rethink the naming scheme, immediately at least.
Suggested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180406100950.19033-1-chris@chris-wilson.co.uk
AFAICT, once the new interrupt is in place, the rest should behave the
same as Gen10.
v2: Update ring frequencies (Sagar)
v3: Rebase.
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405140052.10682-5-mika.kuoppala@linux.intel.com
BSpec says:
"Second level interrupt events are stored in the GT INT DW. GT INT DW is
a double buffered structure. A snapshot of events is taken when SW reads
GT INT DW. From the time of read to the time of SW completely clearing
GT INT DW (to indicate end of service), all incoming interrupts are logged
in a secondary storage structure. this guarantees that the record of
interrupts SW is servicing will not change while under service".
We read GT INT DW in several places now:
- The IRQ handler (banks 0 and 1) where, hopefully, it is completely
cleared (operation now covered with the irq lock).
- The 'reset' interrupts functions for RPS and GuC logs, where we clear
the bit we are interested in and leave the others for the normal
interrupt handler.
- The 'enable' interrupts functions for RPS and GuC logs, as a measure
of precaution. Here we could relax a bit and don't check GT INT DW
at all or, if we do, at least we should clear the offending bit
(which is what this patch does).
Note that, if every bit is cleared on reading GT INT DW, the register
won't be locked. Also note that, according to the BSpec, GT INT DW
cannot be cleared without first servicing the Selector & Shared IIR
registers.
v2:
- Remove some code duplication (Tvrtko)
- Make sure GT_INTR_DW are protected by the irq spinlock, since it's a
global resource (Tvrtko)
v3: Optimize the spinlock (Tvrtko)
v4: Rebase.
v5:
- take spinlock on outer scope to please sparse (Mika)
- use raw_reg accessors (Mika)
v6: omit the continue in looping banks (Michel)
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v4)
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180406093237.14548-1-mika.kuoppala@linux.intel.com
Using the new hierarchical interrupt infrastructure.
v2: Rebase
v3: Rebase
v4: use class/instance handler (Mika)
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405140052.10682-3-mika.kuoppala@linux.intel.com
Interrupt identity register we already read from hardware
contains engine class and instance fields. Leverage
these fields to find correct engine to handle the interrupt.
v3: rebase on top of rps intr
use correct class / instance limits (Michel)
v4: split engine/other handling
v5: empty iir is not err (Daniele, Michel)
Suggested-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180406093145.14389-1-mika.kuoppala@linux.intel.com
The bits used to reset the different engines/domains have changed in
GEN11, this patch maps the reset engine mask bits with the new bits
in the reset control register.
v2: Use shift-left instead of BIT macro to match the file style (Paulo).
v3: Reuse gen8_reset_engines (Daniele).
v4: Do not call intel_uncore_forcewake_reset after reset, we may be
using the forcewake to read protected registers elsewhere and those
results may be clobbered by the concurrent dropping of forcewake.
bspec: 19212
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Antonio Argenziano <antonio.argenziano@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Acked-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405140052.10682-1-mika.kuoppala@linux.intel.com
Now that "DOC: User command execution" of i915_gem_execbuffer.c is included
in the i915.rst, it is benecifial (for new developers) to read what happens
at the bottom of the driver stack (in terms of bytes written to be read
by the GPU) when processing a user-space batchbuffer.
v5:
Typo correction of lacking double tick.
Signed-off-by: Kevin Rogovin <kevin.rogovin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
[Joonas: correcting the patch title]
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1523001957-6427-4-git-send-email-kevin.rogovin@intel.com
Add the documentation of "DOC: User command execution" of
i915_gem_execbuffer.c into a new section in i915.rst.
Signed-off-by: Kevin Rogovin <kevin.rogovin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
[Joonas: correcting the patch title]
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1523001957-6427-3-git-send-email-kevin.rogovin@intel.com
Add a narration to i915.rst about Intel GEN GPU's: engines,
driver context and relocation. Also do minor reorder to improve
narration.
v5:
More type fixes.
Flow bullet list so lines are not too long.
Signed-off-by: Kevin Rogovin <kevin.rogovin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
[Joonas: correcting the patch title]
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1523001957-6427-2-git-send-email-kevin.rogovin@intel.com
We don't handle resetting the kernel context very well, or presumably any
context executing its breadcrumb commands in the ring as opposed to the
batchbuffer and flush. If we trigger a device reset twice in quick
succession while the kernel context is executing, we may end up skipping
the breadcrumb. This is really only a problem for the selftest as
normally there is a large interlude between resets (hangcheck), or we
focus on resetting just one engine and so avoid repeatedly resetting
innocents.
Something to try would be a preempt-to-idle to quiesce the engine before
reset, so that innocent contexts would be spared the reset.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
CC: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180330131801.18327-1-chris@chris-wilson.co.uk
On Apollolake, with stress test warm reboot, audio card was not getting
enumerated after reboot. This was a spurious issue happening on
Apollolake. HW codec and HD audio controller link was going out of sync
for which there was a fix in i915 driver but was not getting invoked for
BXT. Extending this fix to BXT as well.
Tested on apollolake chromebook by stress test warm reboot with 2500
iterations.
Bspec: 21829
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1522946544-11524-1-git-send-email-gaurav.k.singh@intel.com
If we skip the intel_prepare_reset(), we should also skip the
intel_display_reset(). If we we use a flag set by intel_prepare_reset()
then we do not have to second guess based on external user controlled
state whether or not the prepare was called before deciding to finish
it after the reset. igt/gem_eio is one such example that may tweak
i915.reset faster than the code is expecting, leading to
[ 190.233528] =====================================
[ 190.233534] WARNING: bad unlock balance detected!
[ 190.233540] 4.16.0-rc7-g335ef9849310-drmtip_10+ #1 Tainted: G U
[ 190.233547] -------------------------------------
[ 190.233553] gem_eio/1348 is trying to release lock (crtc_ww_class_acquire) at:
[ 190.233569] [<ffffffff895c7810>] drm_modeset_acquire_fini+0x0/0x60
[ 190.233575] but there are no more locks to release!
[ 190.233580]
other info that might help us debug this:
[ 190.233588] 3 locks held by gem_eio/1348:
[ 190.233592] #0: (&f->f_pos_lock){+.+.}, at: [<00000000ab90c784>] __fdget_pos+0x3a/0x50
[ 190.233607] #1: (sb_writers#11){.+.+}, at: [<00000000e1529265>] vfs_write+0x188/0x1a0
[ 190.233622] #2: (&attr->mutex){+.+.}, at: [<0000000011f40afe>] simple_attr_write+0x36/0xd0
[ 190.233635]
stack backtrace:
[ 190.233644] CPU: 0 PID: 1348 Comm: gem_eio Tainted: G U 4.16.0-rc7-g335ef9849310-drmtip_10+ #1
[ 190.233655] Hardware name: Dell Inc. OptiPlex GX280 /0G8310, BIOS A04 02/09/2005
[ 190.233664] Call Trace:
[ 190.233674] dump_stack+0x67/0x95
[ 190.233682] ? drm_modeset_backoff+0x1b0/0x1b0
[ 190.233690] print_unlock_imbalance_bug+0xd2/0xe0
[ 190.233698] ? drm_modeset_backoff+0x1b0/0x1b0
[ 190.233704] lock_release+0x23e/0x300
[ 190.233712] drm_modeset_acquire_fini+0x16/0x60
[ 190.233835] intel_finish_reset+0x72/0x160 [i915]
[ 190.233894] i915_reset_device+0x1e9/0x240 [i915]
[ 190.233953] ? __intel_get_crtc_scanline+0x1c0/0x1c0 [i915]
[ 190.233962] ? work_on_cpu_safe+0x50/0x50
[ 190.234020] i915_handle_error+0x1f2/0x470 [i915]
[ 190.234031] ? __might_fault+0x39/0x90
[ 190.234037] ? __might_fault+0x39/0x90
[ 190.234099] i915_wedged_set+0x7f/0xc0 [i915]
[ 190.234107] simple_attr_write+0xb0/0xd0
[ 190.234117] full_proxy_write+0x51/0x80
[ 190.234125] __vfs_write+0x21/0x140
[ 190.234133] ? rcu_read_lock_sched_held+0x6f/0x80
[ 190.234140] ? rcu_sync_lockdep_assert+0x29/0x50
[ 190.234147] ? __sb_start_write+0x152/0x1f0
[ 190.234152] ? __sb_start_write+0x168/0x1f0
[ 190.234159] vfs_write+0xbd/0x1a0
[ 190.234166] SyS_write+0x40/0xa0
[ 190.234173] ? do_syscall_64+0x19/0x1b0
[ 190.234180] do_syscall_64+0x6b/0x1b0
[ 190.234188] entry_SYSCALL_64_after_hwframe+0x42/0xb7
[ 190.234196] RIP: 0033:0x7f84c1b392b7
[ 190.234201] RSP: 002b:00007f84b6755b00 EFLAGS: 00000293 ORIG_RAX: 0000000000000001
[ 190.234211] RAX: ffffffffffffffda RBX: 0000000000000046 RCX: 00007f84c1b392b7
[ 190.234218] RDX: 0000000000000002 RSI: 000055ec20abc8d6 RDI: 0000000000000046
[ 190.234225] RBP: 000055ec20abc8d6 R08: 0000000000000000 R09: 0000000000000000
[ 190.234231] R10: 0000000000000000 R11: 0000000000000293 R12: 0000000000000002
[ 190.234238] R13: 0000000000000000 R14: 00007f84b0000b20 R15: 000055ec20ce4eb8
Testcase: igt/gem_eio
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405123714.3638-1-chris@chris-wilson.co.uk
Before adding a new feature to execlists submission, we should endeavour
to cover the baseline behaviour with selftests. So start the ball
rolling.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
CC: Michel Thierry <michel.thierry@intel.com>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180404093329.5383-1-chris@chris-wilson.co.uk
Along the eb_lookup_vmas() error path, the return value from
kmem_cache_alloc() was freed using kfree(). Fix it to use the proper
kmem_cache_free() instead.
Fixes: d1b48c1e71 ("drm/i915: Replace execbuf vma ht with an idr")
Signed-off-by: Xidong Wang <wangxidong_97@163.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: <stable@vger.kernel.org> # v4.14+
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180404093824.9313-1-chris@chris-wilson.co.uk
HDCP1.4 key can be loaded, only when Power well #1 is enabled and cdclk
is enabled. Using the I915 power well infrastruture, above requirement
is verified.
This patch enables the hdcp initialization for HSW, BDW, and BXT.
v2:
Choose the PW# based on the platform.
v3:
No Changes.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1522663834-24482-4-git-send-email-ramalingam.c@intel.com
In case of V prime mismatch, DP HDCP spec mandates the re-read of
Vprime atleast twice.
This patch needed for DP HDCP1.4 CTS Test: 1B-05.
v2:
Moved the V' validation into a function for retry. [Sean Paul]
v3:
Removed Inline keyword and DRM_DEBUG_KMS are used [Sean Paul]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1522663834-24482-3-git-send-email-ramalingam.c@intel.com
As per DP spec when R0 mismatch is detected, HDCP source supported
re-read the R0 atleast twice.
And For HDMI and DP minimum wait required for the R0 availability is
100mSec. So this patch changes the wait time to 100mSec but retries
twice with the time interval of 100mSec for each attempt.
This patch is needed for DP HDCP1.4 CTS Test: 1A-06.
v2:
No Change
v3:
Comment on R0 retry is moved closer to the code[Seanpaul]
v4:
Removing unwanted noise introduced in v3.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1522669822-2508-1-git-send-email-ramalingam.c@intel.com
Let's avoid having to delve down the pointer chain to see if the i915
device has support for preemption and store that on the engine, which
made the decision in the first place!
v2: Refactor common preemption policy between execlists/guc.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tomasz Lis <tomasz.lis@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180403183537.5522-1-chris@chris-wilson.co.uk
We would like to start doing some bookkeeping at the beginning, between
contexts and at the end of execlists submission. We already mark the
beginning and end using EXECLISTS_ACTIVE_USER, to provide an indication
when the HW is idle. This give us a pair of sequence points we can then
expand on for further bookkeeping.
v2: Refactor guc submission to share the same begin/end.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180331130626.10712-1-chris@chris-wilson.co.uk
Commit 'aee3bac0a3a8 ("drm/i915/psr: Tie PSR2 support to Y
coordinate requirement")' got merged to drm-intel-next-queued
but the variable was defined commit 'c5fe47327b06 ("drm: Add PSR
version 3 macro") who was merged through drm-misc.
So backmerging to get drm-intel-next-queued compiling back again.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
In the 2 eDP1.4a pannels tested set or not set bit have no effect
but is better set it and comply with specification.
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-9-jose.souza@intel.com
This value do not change overtime so better cache it than
fetch it every PSR enable.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-8-jose.souza@intel.com
Sink can support our PSR2 requirements but userspace can request
a resolution that PSR2 hardware do not support, in this case it
was overwritten the PSR2 sink support.
Adding another flag here, this way if requested resolution changed
to a value that PSR2 hardware can handle, PSR2 can be enabled.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-6-jose.souza@intel.com
For Geminilake and Cannonlake+ the Y-coordinate support must be
enabled in PSR2_CTL too.
Spec: 7713 and 7720
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-5-jose.souza@intel.com
Although i915 don't implement aux sync frame through tests was
findout that pannels can do selective update when the y-coordinate
is also included in SDP, that is why it is required to run PSR2 in
i915.
So moving to only one place the sink requirements that the actual
driver needs to enable PSR2.
Also intel_psr2_config_valid() is called every time the crtc config
is computed, wasting some time every time it was checking for
Y coordinate requirement.
This allow us to nuke y_cord_support and some of VSC setup code that
was handling a scenario that would never happen(PSR2 without Y
coordinate).
Also here renaming intel_dp_get_y_cord_status() to
intel_dp_get_y_coord_required() as it more accurate to the name and
function of bit according to eDP spec.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-4-jose.souza@intel.com
eDP spec states that aux frame is required to do PSR2 selective
update but i915 don't fully implement it. It sends the aux frame
sync messages but the value is always zero as the GTC is not enabled
in driver.
Through tests was findout that pannels can do selective update when
the y-coordinate is also included in SDP, that is why it is required
to run PSR2 in i915.
A dummy value is not useful at all to sink, so removing everything
related to aux frame sync, if GTC is enabled we can bring this back.
Cc: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-3-jose.souza@intel.com
As intel_wait_for_register_fw() may use, and if successful only use, a
busy-wait loop, the might_sleep() warning is a little over-zealous.
Restrict it to a might_sleep_if() a slow timeout is specified (and so
the caller authorises use of a usleep).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180329224519.13598-2-chris@chris-wilson.co.uk
Only sleep and repeat when asked for a full device reset (ALL_ENGINES)
and avoid using sleeping waits when asked for a per-engine reset. The
goal is to be able to use a per-engine reset from hardirq/softirq/timer
context. A consequence is that our individual wait timeouts are a
thousand times shorter, on the order of a hundred microseconds rather
than hundreds of millisecond. This may make hitting the timeouts more
common, but hopefully the fallover to the full-device reset will be
sufficient to pick up the pieces.
Note, that the sleeps inside older gen (pre-gen8) have been left as they
are only used in full device reset mode.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
CC: Michel Thierry <michel.thierry@intel.com>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180329224519.13598-1-chris@chris-wilson.co.uk
In commit d79651522e ("drm/i915: Enable i915 perf stream for
Haswell OA unit") the enable/disable vfunc hadn't appear yet and the
same function would deal with enabling/disabling the OA unit.
This was split later on for gen8 but the gen7 retained some code that
isn't actually useful anymore.
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326090831.22686-4-lionel.g.landwerlin@intel.com
Probably lost while rebasing commit eacd8391f9 ("drm/i915/guc: Keep GuC
interrupts enabled when using GuC").
Not really needed since i915_gem_init_hw is called before uc_resume, but
it brings symmetry to uc_suspend.
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328205851.16188-1-michel.thierry@intel.com
- Mask mode type garbage from userspace (Ville)
Something went wrong on the misc tree side, but I'll pull the patch directly.
* 'drm-misc-next-fixes' of git://anongit.freedesktop.org/drm/drm-misc:
drm: Fix uabi regression by allowing garbage mode->type from userspace
During debug we may want to investigate all communication
from the Guc. Add proper tracing macros in debug config.
v2: convert remaining DRM_DEBUG into new CT_DEBUG (Michal)
v3: use dedicated Kconfig (Daniele)
v4: checkpatch
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326194829.58836-12-michal.wajdeczko@intel.com
When running on platform with CTB based GuC communication enabled,
GuC to Host event data will be delivered as CT request message.
However, content of the data[1] of this CT message follows format
of the scratch register used in MMIO based communication, so some
code reuse is still possible.
v2: filter disabled messages (Daniele)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> #1
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Acked-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180327214124.70680-1-michal.wajdeczko@intel.com
Requests are read from CT in the irq handler, but actual processing
will be done in the work thread. Processing of specific actions will
be added in the upcoming patches.
v2: don't use GEM_BUG_ON (Chris)
don't kmalloc too large buffer (Michal)
v3: rebased
v4: don't name it 'dispatch' (Michel) and fix checkpatch
add some documentation (Michal)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326194829.58836-10-michal.wajdeczko@intel.com
Instead of returning small data in response status dword,
GuC may append longer data as response message payload.
If caller provides response buffer, we will copy received
data and use number of received data dwords as new success
return value. We will WARN if response from GuC does not
match caller expectation.
v2: fix timeout and checkpatch warnings (Michal)
v3: fix checkpatch again (Michel)
update wait function name (Michal)
no need for spinlock_irqsave (MichalWi)
no magic numbers (MichalWi)
must check before use (Jani)
add some more documentation (Michal)
v4: update documentation (Michal)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> #2.5
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180327121439.70096-1-michal.wajdeczko@intel.com
In next patch we will introduce another way of waiting for the response
that will use RECV buffer. To avoid misleading names, rename old wait
function to reflect the fact that it is based on descriptor update.
v2: fix comment style (Michal)
v3: use more specific name (Michel)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326194829.58836-8-michal.wajdeczko@intel.com
Lyude Paul