drivers/net/phy/phy_device.c: In function ‘get_phy_device’:
drivers/net/phy/phy_device.c:340:14: warning: ‘phy_id’ may be used uninitialized in this function [-Wmaybe-uninitialized]
GCC can't see that when we return zero we always initialize
phy_id and that's the only path where we use it.
Initialize phy_id to zero to shut it up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a driver for BCM8706 and BCM8727 devices. These are a 10Gig PHYs
which use MII_ADDR_C45 addressing. They are always 10G full duplex, so
there is no autonegotiation. All we do is report link state and send
interrupts when it changes.
If the PHY has a device tree of_node associated with it, the
"broadcom,c45-reg-init" property is used to supply register
initialization values when config_init() is called.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow PHY drivers to supply their own device matching function
(match_phy_device()), or to be matched OF compatible properties.
PHYs following IEEE802.3 clause 45 have more than one device
identifier constants, which breaks the default device matching code.
Other 10G PHYs don't follow the standard manufacturer/device
identifier register layout standards, but they do use the standard
MDIO bus protocols for register access. Both of these require
adjustments to the PHY driver to device matching code.
If the there is an of_node associated with such a PHY, we can match it
to its driver using the "compatible" properties, just as we do with
certain platform devices. If the "compatible" property match fails,
first check if there is a driver supplied matching function, and if
not fall back to the existing identifier matching rules.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IEEE802.3 clause 45 MDIO bus protocol allows for directly
addressing PHY registers using a 21 bit address, and is used by many
10G Ethernet PHYS. Already existing is the ability of MDIO bus
drivers to use clause 45, with the MII_ADDR_C45 flag. Here we add
struct phy_c45_device_ids to hold the device identifier registers
present in clause 45. struct phy_device gets a couple of new fields:
c45_ids to hold the identifiers and is_c45 to signal that it is clause
45.
get_phy_device() gets a new parameter is_c45 to indicate that the PHY
device should use the clause 45 protocol, and its callers are adjusted
to pass false. The follow-on patch to of_mdio.c will pass true where
appropriate.
EXPORT phy_device_create() so that the follow-on patch to of_mdio.c
can use it to create phy devices for PHYs, that have non-standard
device identifier registers, based on the device tree bindings.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/qmi_wwan.c
net/batman-adv/translation-table.c
net/ipv6/route.c
qmi_wwan.c resolution provided by Bjørn Mork.
batman-adv conflict is dealing merely with the changes
of global function names to have a proper subsystem
prefix.
ipv6's route.c conflict is merely two side-by-side additions
of network namespace methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
On a freescale imx6q platform, a hardware phy chip KSZ9021 is
recognized as a KS8001 chip by the current driver like this:
eth0: Freescale FEC PHY driver [Micrel KS8001 or KS8721]
KSZ9021 has phy_id 0x00221610, while KSZ8001 has phy_id
0x0022161a, the current phy_id_mask (0x00fffff0/0x00ffff10) can't
distinguish them. So change phy_id_mask to resolve this problem.
Although the micrel datasheet says that the 4 LSB of phyid2 register
contains the chip revision number and the current driver is designed
to follow this rule, in reality the chip implementation doesn't follow
it.
Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
drivers/net/wireless/iwlwifi/pcie/trans.c
The iwlwifi conflict was resolved by keeping the code added
in 'net' that turns off the buggy chip feature.
The MAINTAINERS conflict was merely overlapping changes, one
change updated all the wireless web site URLs and the other
changed some GIT trees to be Johannes's instead of John's.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more current logging style.
Add pr_fmt and missing newlines.
Remove embedded prefixes.
Neaten phy_print_status to avoid using KERN_CONT.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warnings in drivers/net/phy:
Warning(drivers/net/phy/mdio_bus.c:109): No description found for parameter 'mdio_bus_np'
Warning(drivers/net/phy/mdio_bus.c:109): Excess function parameter 'mdio_np' description in 'of_mdio_find_bus'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the interrupt mask for IC101 A/G devices
and now enables the link/speed/duplex interrupts.
This is done by setting the "INTR pin used" bit and cleaning
all the other bits in the Register 17.
Reported-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is only referenced from within phy_device.c, so there is
no reason to export it. In fact, we can make it static.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_OF_MDIO is tristate and will be m if PHYLIB is m. Use
IS_ENABLED macro to prevent build error:
ERROR: "of_mdio_find_bus" [drivers/net/phy/mdio-mux.ko] undefined!
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO pins select which sub bus is connected to the master.
Initially tested with an sn74cbtlv3253 switch device wired into the
MDIO bus.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a somewhat generic framework for MDIO bus
multiplexers. It is modeled on the I2C multiplexer.
The multiplexer is needed if there are multiple PHYs with the same
address connected to the same MDIO bus adepter, or if there is
insufficient electrical drive capability for all the connected PHY
devices.
Conceptually it could look something like this:
------------------
| Control Signal |
--------+---------
|
--------------- --------+------
| MDIO MASTER |---| Multiplexer |
--------------- --+-------+----
| |
C C
h h
i i
l l
d d
| |
--------- A B ---------
| | | | | |
| PHY@1 +-------+ +---+ PHY@1 |
| | | | | |
--------- | | ---------
--------- | | ---------
| | | | | |
| PHY@2 +-------+ +---+ PHY@2 |
| | | |
--------- ---------
This framework configures the bus topology from device tree data. The
mechanics of switching the multiplexer is left to device specific
drivers.
The follow-on patch contains a multiplexer driven by GPIO lines.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add of_mdio_find_bus() which allows an mii_bus to be located given its
associated the device tree node.
This is needed by the follow-on patch to add a driver for MDIO bus
multiplexers.
The of_mdiobus_register() function is modified so that the device tree
node is recorded in the mii_bus. Then we can find it again by
iterating over all mdio_bus_class devices.
Because the OF device tree has now become an integral part of the
kernel, this can live in mdio_bus.c (which contains the needed
mdio_bus_class structure) instead of of_mdio.c.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix merge between commit 3adadc08cc ("net ax25: Reorder ax25_exit to
remove races") and commit 0ca7a4c87d ("net ax25: Simplify and
cleanup the ax25 sysctl handling")
The former moved around the sysctl register/unregister calls, the
later simply removed them.
With help from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes and adds the irq handler for the
IC+ 101A/G where we need to read the reg17 to clean
the irq.
Also remove the flag for the 1001LF where no interrupt
can be used for this device.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register() so
we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Frederic Lambert <frdrc66@gmail.com>
Cc: netdev@vger.kernel.org
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compile tested.
remove unnecessary code that matches this coccinelle pattern
ret = phy_write(x, y , z)
if (ret < 0)
return ret;
return 0;
As phy_write returns error code, we dont need to do not need extra check
before returning.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compile tested.
remove unnecessary code that matches this coccinelle pattern
ret = phy_write(x, y , z)
if (ret < 0)
return ret;
return 0;
As phy_write returns error code, we dont need to do not need extra check
before returning.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compile tested.
remove unnecessary code that matches this coccinelle pattern
ret = phy_write(x, y , z)
if (ret < 0)
return ret;
return 0;
As phy_write returns error code, we dont need to do not need extra check
before returning.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes Auto Power Saving configuration in ip101a_config_init
which was broken as there is no phy register write followed after
setting IP101A_APS_ON flag.
This patch also fixes the return value of ip101a_config_init.
Without this patch ip101a_config_init returns 2 which is not an error
accroding to IS_ERR and the mac driver will continue accessing 2 as
valid pointer to phy_dev resulting in memory fault.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This branch takes the PowerPC irq_host infrastructure (reverse mapping
from Linux IRQ numbers to hardware irq numbering), generalizes it,
renames it to irq_domain, and makes it available to all architectures.
Originally the plan has been to create an all-new irq_domain
implementation which addresses some of the powerpc shortcomings such
as not handling 1:1 mappings well, but doing that proved to be far
more difficult and invasive than generalizing the working code and
refactoring it in-place. So, this branch rips out the 'new'
irq_domain and replaces it with the modified powerpc version (in a
fully bisectable way of course). It converts all users over to the
new API and makes irq_domain selectable on any architecture.
No architecture is forced to enable irq_domain, but the infrastructure
is required for doing OpenFirmware style irq translations. It will
even work on SPARC even though SPARC has it's own mechanism for
translating irqs at boot time. MIPS, microblaze, embedded x86 and c6x
are converted too.
The resulting irq_domain code is probably still too verbose and can be
optimized more, but that can be done incrementally and is a task for
follow-on patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPZ1yiAAoJEEFnBt12D9kB4yIQAJvCfTPL65sCYVD6i9RnVHtR
ahwddtd0AtT+UYLU8Xg2fZgVi6cmupDGnqkBixzZD3xxSTERqm7Snqa0ugklfeAi
B6Zqf/K17H5hJNaoQ3fkNauow8m7ZYOeEH2vVUvkb3woWS9Wm7OGd+BvcIBgYSGe
Aaoumhu7kDxFkii0qz3x/+kvsb6DRp2HtSPWj+APL/kNjdiO4JBOihtcc/lX6d47
bsZLiEMzHUFV4ApJNwqmfDnf54oMrHmrRJxgQHIMjeJC5or9I3Do8wDGe/aTF5xO
5GVpxCQsTlJMjTBWlAFtpTwCJB6y76EHQrHc7WzLlq8OJSsxApOke8M0BzXFrfMy
CU7UUpTvNZTLpZibLCEQKemv1+oNOkfFylsHxfek2MCqx0W6W4FHEGV3qE/GtgV9
+vurA9hNNp7VM0FGRGigcUr3woYdHLdEVQrlnL7Z9AgBu1W44MZLaai7iRVZOeCT
ZQ9++v2PJJ8vHT8kdkgTdiRpnEhmv84MX/GBT7ilWFEMIVeT5zhGkIBojzNgyzGc
7cvermmM0P8h+unkDgmzmSbDxo0PboqVKeoO71AOBhA6MmR9iom7XkuNdHhoOwy2
4A5xT1srbhJDbuv15BBREBV24TywpZ4a1+4nwQT4L1fXe+HfCxeEWexGcKQMRcIt
dAelOHTQ+ZGkOKvXeW05
=ruGA
-----END PGP SIGNATURE-----
Merge tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull irq_domain support for all architectures from Grant Likely:
"Generialize powerpc's irq_host as irq_domain
This branch takes the PowerPC irq_host infrastructure (reverse mapping
from Linux IRQ numbers to hardware irq numbering), generalizes it,
renames it to irq_domain, and makes it available to all architectures.
Originally the plan has been to create an all-new irq_domain
implementation which addresses some of the powerpc shortcomings such
as not handling 1:1 mappings well, but doing that proved to be far
more difficult and invasive than generalizing the working code and
refactoring it in-place. So, this branch rips out the 'new'
irq_domain and replaces it with the modified powerpc version (in a
fully bisectable way of course). It converts all users over to the
new API and makes irq_domain selectable on any architecture.
No architecture is forced to enable irq_domain, but the infrastructure
is required for doing OpenFirmware style irq translations. It will
even work on SPARC even though SPARC has it's own mechanism for
translating irqs at boot time. MIPS, microblaze, embedded x86 and c6x
are converted too.
The resulting irq_domain code is probably still too verbose and can be
optimized more, but that can be done incrementally and is a task for
follow-on patches."
* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6: (31 commits)
dt: fix twl4030 for non-dt compile on x86
mfd: twl-core: Add IRQ_DOMAIN dependency
devicetree: Add empty of_platform_populate() for !CONFIG_OF_ADDRESS (sparc)
irq_domain: Centralize definition of irq_dispose_mapping()
irq_domain/mips: Allow irq_domain on MIPS
irq_domain/x86: Convert x86 (embedded) to use common irq_domain
ppc-6xx: fix build failure in flipper-pic.c and hlwd-pic.c
irq_domain/microblaze: Convert microblaze to use irq_domains
irq_domain/powerpc: Replace custom xlate functions with library functions
irq_domain/powerpc: constify irq_domain_ops
irq_domain/c6x: Use library of xlate functions
irq_domain/c6x: constify irq_domain structures
irq_domain/c6x: Convert c6x to use generic irq_domain support.
irq_domain: constify irq_domain_ops
irq_domain: Create common xlate functions that device drivers can use
irq_domain: Remove irq_domain_add_simple()
irq_domain: Remove 'new' irq_domain in favour of the ppc one
mfd: twl-core.c: Fix the number of interrupts managed by twl4030
of/address: add empty static inlines for !CONFIG_OF
irq_domain: Add support for base irq and hwirq in legacy mappings
...
Pull networking merge from David Miller:
"1) Move ixgbe driver over to purely page based buffering on receive.
From Alexander Duyck.
2) Add receive packet steering support to e1000e, from Bruce Allan.
3) Convert TCP MD5 support over to RCU, from Eric Dumazet.
4) Reduce cpu usage in handling out-of-order TCP packets on modern
systems, also from Eric Dumazet.
5) Support the IP{,V6}_UNICAST_IF socket options, making the wine
folks happy, from Erich Hoover.
6) Support VLAN trunking from guests in hyperv driver, from Haiyang
Zhang.
7) Support byte-queue-limtis in r8169, from Igor Maravic.
8) Outline code intended for IP_RECVTOS in IP_PKTOPTIONS existed but
was never properly implemented, Jiri Benc fixed that.
9) 64-bit statistics support in r8169 and 8139too, from Junchang Wang.
10) Support kernel side dump filtering by ctmark in netfilter
ctnetlink, from Pablo Neira Ayuso.
11) Support byte-queue-limits in gianfar driver, from Paul Gortmaker.
12) Add new peek socket options to assist with socket migration, from
Pavel Emelyanov.
13) Add sch_plug packet scheduler whose queue is controlled by
userland daemons using explicit freeze and release commands. From
Shriram Rajagopalan.
14) Fix FCOE checksum offload handling on transmit, from Yi Zou."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1846 commits)
Fix pppol2tp getsockname()
Remove printk from rds_sendmsg
ipv6: fix incorrent ipv6 ipsec packet fragment
cpsw: Hook up default ndo_change_mtu.
net: qmi_wwan: fix build error due to cdc-wdm dependecy
netdev: driver: ethernet: Add TI CPSW driver
netdev: driver: ethernet: add cpsw address lookup engine support
phy: add am79c874 PHY support
mlx4_core: fix race on comm channel
bonding: send igmp report for its master
fs_enet: Add MPC5125 FEC support and PHY interface selection
net: bpf_jit: fix BPF_S_LDX_B_MSH compilation
net: update the usage of CHECKSUM_UNNECESSARY
fcoe: use CHECKSUM_UNNECESSARY instead of CHECKSUM_PARTIAL on tx
net: do not do gso for CHECKSUM_UNNECESSARY in netif_needs_gso
ixgbe: Fix issues with SR-IOV loopback when flow control is disabled
net/hyperv: Fix the code handling tx busy
ixgbe: fix namespace issues when FCoE/DCB is not enabled
rtlwifi: Remove unused ETH_ADDR_LEN defines
igbvf: Use ETH_ALEN
...
Fix up fairly trivial conflicts in drivers/isdn/gigaset/interface.c and
drivers/net/usb/{Kconfig,qmi_wwan.c} as per David.
This commit brings the author email address macros up to date for four
modules in the PTP Hardware Clock subsystem.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/sfc/rx.c
Overlapping changes in drivers/net/ethernet/sfc/rx.c, one to change
the rx_buf->is_page boolean into a set of u16 flags, and another to
adjust how ->ip_summed is initialized.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the PHY_HAS_INTERRUPT flag for IC+101 device series.
Also the patch does a simple dity-up to signal that
the driver actually is for IP101A LF and IP101G devices.
In fact, these are two similar PHYs that have the same IDs
and mainly differ for the EEE capability supported in the
G series.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code for ip1001_config_init() was totally broken if you were not
using RGMII. Instead of returning an error code or zero it actually
returned the value in the IP1001_SPEC_CTRL_STATUS_2 register. It was
also trying to set the IP1001_APS_ON bit , but never actually wrote
back the register.
The error checking was also incorrect in both this function and the
reset function, so this patch fixes that up in a consistent fashion.
Signed-off-by: David McKay <david.mckay@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the x86-specific definition of irq_domain and replaces
it with the common implementation.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Booleans should not be compared to true or false
but be directly tested or tested with !.
Done via cocci script:
@@
bool t;
@@
- t == true
+ t
@@
bool t;
@@
- t != true
+ !t
@@
bool t;
@@
- t == false
+ !t
@@
bool t;
@@
- t != false
+ t
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was done to resolve a merge and build problem with the
drivers/acpi/processor_driver.c file.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of the removal of get_driver()/put_driver(), this patch
(as1512) gets rid of various useless and unnecessary calls in several
drivers. In some cases it may be desirable to pin the driver by
calling try_module_get(), but that can be done later.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: "David S. Miller" <davem@davemloft.net>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: Michael Buesch <m@bues.ch>
CC: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix new kernel-doc warning:
Warning(drivers/net/phy/mdio_bus.c:49): No description found for parameter 'size'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar problem as in 481a819914 ("can:
fix NOHZ local_softirq_pending 08 warning"). This fix replaces
netif_rx() with netif_rx_ni() which has to be used from
process/softirq context.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce function mdiobus_alloc_size() as an alternative to mdiobus_alloc().
Most callers of mdiobus_alloc() also allocate a private data structure, and
then manually point bus->priv to this object. mdiobus_alloc_size()
combines the two operations into one, which simplifies memory management.
The original mdiobus_alloc() now just calls mdiobus_alloc_size(0).
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMSC generation 4 LAN chips integrate an IEEE 802.3 ethernet physical layer.
The ethernet driver for this family of devices needs to access the SMSC PHY
registers and bit-fields.
So, this patch moves these constants to a place where it can be used for both
the PHY and LAN drivers.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Frederic Lambert <frdrc66@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 88491d8103 ("drivers/net: Kconfig
& Makefile cleanup") changed the type of these options to bool, but
they select code that could (and still can) be built as modules.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements advice by Ben Hutchings to change the mii side of
the function names to look more like the register whose values they
convert. New LPA translation functions have been added as well.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Translating between ethtool advertisement settings and MII
advertisements are common operations for ethernet drivers. This patch
adds a set of helper functions that implements the conversion. The
patch then modifies a couple of the drivers to use the new functions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds phy reset functionality to mdio-gpio driver. Now
mdio_gpio_platform_data has new member as function pointer which can be
filled at the bsp level for a callback from phy infrastructure. Also the
mdio-bitbang driver fills-in the reset function of mii_bus structure.
Without this patch the bsp level code has to takecare of the reseting
PHY's on the bus, which become bit hacky for every bsp and
phy-infrastructure is ignored aswell.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device.h header was including module.h, making it present for
most of these drivers. But we want to clean that up. Call out the
include of module.h in the modular network drivers.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1745 commits)
dp83640: free packet queues on remove
dp83640: use proper function to free transmit time stamping packets
ipv6: Do not use routes from locally generated RAs
|PATCH net-next] tg3: add tx_dropped counter
be2net: don't create multiple RX/TX rings in multi channel mode
be2net: don't create multiple TXQs in BE2
be2net: refactor VF setup/teardown code into be_vf_setup/clear()
be2net: add vlan/rx-mode/flow-control config to be_setup()
net_sched: cls_flow: use skb_header_pointer()
ipv4: avoid useless call of the function check_peer_pmtu
TCP: remove TCP_DEBUG
net: Fix driver name for mdio-gpio.c
ipv4: tcp: fix TOS value in ACK messages sent from TIME_WAIT
rtnetlink: Add missing manual netlink notification in dev_change_net_namespaces
ipv4: fix ipsec forward performance regression
jme: fix irq storm after suspend/resume
route: fix ICMP redirect validation
net: hold sock reference while processing tx timestamps
tcp: md5: add more const attributes
Add ethtool -g support to virtio_net
...
Fix up conflicts in:
- drivers/net/Kconfig:
The split-up generated a trivial conflict with removal of a
stale reference to Documentation/networking/net-modules.txt.
Remove it from the new location instead.
- fs/sysfs/dir.c:
Fairly nasty conflicts with the sysfs rb-tree usage, conflicting
with Eric Biederman's changes for tagged directories.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (59 commits)
MAINTAINERS: linux-m32r is moderated for non-subscribers
linux@lists.openrisc.net is moderated for non-subscribers
Drop default from "DM365 codec select" choice
parisc: Kconfig: cleanup Kernel page size default
Kconfig: remove redundant CONFIG_ prefix on two symbols
cris: remove arch/cris/arch-v32/lib/nand_init.S
microblaze: add missing CONFIG_ prefixes
h8300: drop puzzling Kconfig dependencies
MAINTAINERS: microblaze-uclinux@itee.uq.edu.au is moderated for non-subscribers
tty: drop superfluous dependency in Kconfig
ARM: mxc: fix Kconfig typo 'i.MX51'
Fix file references in Kconfig files
aic7xxx: fix Kconfig references to READMEs
Fix file references in drivers/ide/
thinkpad_acpi: Fix printk typo 'bluestooth'
bcmring: drop commented out line in Kconfig
btmrvl_sdio: fix typo 'btmrvl_sdio_sd6888'
doc: raw1394: Trivial typo fix
CIFS: Don't free volume_info->UNC until we are entirely done with it.
treewide: Correct spelling of successfully in comments
...
If the PHY should disappear (for example, on an USB Ethernet MAC), then
the driver would leak any undelivered time stamp packets. This commit
fixes the issue by calling the appropriate functions to free any packets
left in the transmit and receive queues.
The driver first appeared in v3.0.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous commit enforces a new rule for handling the cloned packets
for transmit time stamping. These packets must not be freed using any other
function than skb_complete_tx_timestamp. This commit fixes the one and only
driver using this API.
The driver first appeared in v3.0.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit
"7488876... dt/net: Eliminate users of of_platform_{,un}register_driver"
there are two platform drivers named "mdio-gpio" registered.
I renamed the of variant to "mdio-ofgpio".
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Vitesse driver was using the RGMII_ID interface type to determine if
skew was necessary. However, we want to move away from using that
interface type, as it's really a property of the board's PHY connection.
However, some boards depend on it, so we want to support it, while
allowing new boards to use the more flexible "fixups" approach. To do
this, we extract the code which adds skew into its own function, and
call that function when RGMII_ID has been selected.
Another side-effect of this change is that if your PHY has skew set
already, it doesn't clear it. This way, the fixup code can modify the
register without config_init then clearing it.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The extra delay of 2ns to adjust RX clock phase is actually needed
in RGMII mode. Tested on the HDK7108 (STx7108c2).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Usually you have to take the bus lock. Why not here too?
I saw this when working on something else. Not even compile tested.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Cc: "Uwe Kleine-Konig" <u.kleine-koenig@pengutronix.de>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accesses to the mdio busses must be done with the mdio_lock to ensure
proper operation. Conveniently we have the helper function
mdiobus_read() to do that for us. Lets use it in get_phy_id() instead
of accessing the bus without the lock held.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver has two warning messages that might be triggered
by normal use cases. When they appear, the messages give the
impression of a never ending series of errors.
This commit changes them to debug messages instead.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds one step support to the phyter. When enabled, the
hardware does not provide time stamps for transmitted sync messages but
instead inserts the stamp into the outgoing packet.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables six external event channels and one periodic output.
One GPIO is reserved for synchronizing multiple PHYs. The assignment
of GPIO functions can be changed via a module parameter.
The code supports multiple simultaneous events by inducing a PTP clock
event for every channel marked in the PHY's extended status word.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the IC+ IP101A Single port 10/100 PHY
and supports the APS (i.e. power saving mode while link is down)
for both IP1001 and IP101A (where this mode is supported).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The is does a general cleanup of the drivers/net/ Kconfig and
Makefile. This patch create a "core" option and places all
the networking core drivers into this option (default is yes
for this option). In addition, it alphabitizes the Kconfig
driver options.
As a side cleanup, found that the arcnet, token ring, and PHY
Kconfig options were a tri-state option and should have been
a bool option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to the DP83865 datasheet we need to clear
the interrupt status bit by writing a 1 to the
corresponding bit in INT_CLEAR (2:0 are reserved).
Proposed and tested by Thorsten.
Signed-off-by: Thorsten Schubert <tshu@msc-ge.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dp83640 buffers receive time stamps from special PHY status frames,
matching them to received PTP packets in a work queue. Because the timeout
for orphaned time stamps is so long and the buffer is so small, the driver
can drop time stamps under moderate PTP traffic.
This commit fixes the issue by decreasing the timeout to (at least) one
timer tick and increasing the buffer size.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Cc: <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Compile tested.
remove unnecessary code that matches this coccinelle pattern
if (...)
return ret;
return ret;
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
The dp83640 PHY provides time stamp and other information via special
PHY status frames. Previously, the driver decoded the frames and then
let the network stack drop them. This works fine when the PTP messages
come over UDP.
However, when receiving PTP messages via L2 packets, this creates a
problem. The status frames use the official PTP destination MAC address,
and so they are delivered to user space along with the "real" frames,
causing confusion for applications.
This commit fixes the issue by simply dropping the PHY status frames
in the driver.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
If two eternal time stamp events occur at nearly the same time, the
phyter will add an extra word into the status frame. This commit fixes
the parsing code to recognize and skip over the extra word.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
This PHY is available integrated into BCM63xx series SOCs only.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/phy/Kconfig | 1 +
1 files changed, 1 insertions(+), 0 deletions(-)
Acked-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
If the dp83640 driver is not built as a module, the
MODULE_DEVICE_TABLE reference to dp83640_tbl nops out.
Since the table isn't referenced elsewhere, it it causes
the following warning:
drivers/net/phy/dp83640.c:1095: warning: ‘dp83640_tbl’ defined but not used
This apparently is common with mdio_device_id table structures,
and is avoided by using __maybe_unused annotation.
Signed-off-by: John Stultz <john.stultz@linaro.org>
This patch adds support for the PTP clock found on the DP83640.
The basic clock operations and one external time stamp have
been implemented.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: John Stultz <john.stultz@linaro.org>
This updates the network drivers so that they don't access the
ethtool_cmd::speed field directly, but use ethtool_cmd_speed()
instead.
For most of the drivers, these changes are purely cosmetic and don't
fix any problem, such as for those 1GbE/10GbE drivers that indirectly
call their own ethtool get_settings()/mii_ethtool_gset(). The changes
are meant to enforce code consistency and provide robustness with
future larger throughputs, at the expense of a few CPU cycles for each
ethtool operation.
All drivers compiled with make allyesconfig ion x86_64 have been
updated.
Tested: make allyesconfig on x86_64 + e1000e/bnx2x work
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes sure the ethtool's set_settings() callback of network
drivers don't ignore the 16 most significant bits when ethtool calls
their set_settings().
All drivers compiled with make allyesconfig on x86_64 have been
updated.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function phy_attach_direct attaches the phy and calls phy_init_hw.
phy_init_hw can fail, but the phy is still marked as attached. Successive
calls to phy_attach_direct will fail because the phy is busy.
[ 1.020000] eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1:00, irq=-1)
[ 1.030000] eth1: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1:01, irq=-1)
[ 2.050000] Sending DHCP requests .
[ 3.020000] PHY: 1:00 - Link is Up - 100/Full
[ 5.110000] ..... timed out!
[ 87.660000] IP-Config: Reopening network devices...
[ 88.190000] FEC: MDIO read timeout
[ 88.190000] eth0: could not attach to PHY
[ 88.190000] IP-Config: Failed to open eth0
[ 88.210000] FEC: MDIO read timeout
[ 88.210000] eth1: could not attach to PHY
[ 88.210000] IP-Config: Failed to open eth1
[ 88.220000] IP-Config: No network devices available.
[ 88.220000] Freeing init memory: 6968K
[...]
starting network interfaces...
ip: RTNETLINK answers: File exists
[ 94.000000] net eth0: PHY already attached
[ 94.010000] eth0: could not attach to PHY
ip: SIOCSIFFLAGS: Device or resource busy
This patch adds phy_detach to clean up if phy_init_hw fails.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylib would silently ignore the phy_id argument to these ioctls and
perform the read/write with the active phydev address, whereas most
non-phylib drivers seem to allow access to all mdio addresses
(E.G. pcnet_cs).
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of users of of_platform_driver in drivers/net. The
of_platform_{,un}register_driver functions are going away, so the
users need to be converted to using the platform_bus_type directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Platform code can now set the MICREL_PHY_50MHZ_CLK bit of dev_flags in a fixup
routine (registered with phy_register_fixup_for_uid()), to make the KZS8051RNL
PHY work with 50MHz RMII reference clock.
Cc: David J. Choi <david.choi@micrel.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unneeded depends on PHYLIB. The config selection is already in
an if PHYLIB / endif block.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the IC+ IP1001 (Gigabit Ethernet Transceiver) driver.
I've had to add an additional delay (2ns) to adjust RX clock phase at
GMII/ RGMII interface (according to the PHY data-sheet). This helps to
have the RGMII working on some ST platforms.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some aspects of PHY initialization are board dependent, things like
indicator LED connections and some clocking modes cannot be determined
by probing. The dev_flags element of struct phy_device can be used to
control these things if an appropriate value can be passed from the
Ethernet driver. We run into problems however if the PHY connections
are specified by the device tree. There is no way for the Ethernet
driver to know what flags it should pass.
If we are using the device tree, the struct phy_device will be
populated with the device tree node corresponding to the PHY, and we
can extract extra configuration information from there.
The next question is what should the format of that information be?
It is highly device specific, and the device tree representation
should not be tied to any arbitrary kernel defined constants. A
straight forward representation is just to specify the exact bits that
should be set using the "marvell,reg-init" property:
phy5: ethernet-phy@5 {
reg = <5>;
compatible = "marvell,88e1149r";
marvell,reg-init =
/* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */
<3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */
/* mix %:0, led[0123]:drive low off hiZ */
<3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */
/* default blink periods. */
<3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */
/* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */
<3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */
};
phy6: ethernet-phy@6 {
reg = <6>;
compatible = "marvell,88e1118";
marvell,reg-init =
/* Fix rx and tx clock transition timing */
<2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */
/* Adjust LED drive. */
<3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */
/* irq, blink-activity, blink-link */
<3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */
};
The Marvell PHYs have a page select register at register 22 (0x16), we
can specify any register by its page and register number. These are
the first and second word. The third word contains a mask to be ANDed
with the existing register value, and the fourth word is ORed with the
result to yield the new register value. The new marvell_of_reg_init
function leaves the page select register unchanged, so a call to it
can be dropped into the .config_init functions without unduly
affecting the state of the PHY.
If CONFIG_OF_MDIO is not set, there is no of_node, or no
"marvell,reg-init" property, the PHY initialization is unchanged.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E1149R is 10/100/1000 quad-gigabit Ethernet PHY. The
.config_aneg function can be shared with 88E1118, but it needs its own
.config_init.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The definition of the Marvell PHY page register is not specific to
88E1121, so rename the macro to MII_MARVELL_PHY_PAGE, and use it
throughout.
Suggested-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The marvell 88ec048's official part number is 88e1318s. This patch renames
definitions in the driver to reflect this.
In addition, a minor bug fix has been added to write back the MSCR1 register
value properly.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following functions are not used directly by any drivers:
phy_attach_direct
phy_device_create
phy_prepare_link
genphy_config_advert
genphy_setup_forced
phy_config_interrupt
phy_clear_interrypt
phy_sanitize_settings
phy_enable_interrupts
phy_disable_interrupts
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c477d0447d added support for RGMII
rx/tx delays except that it ends up clearing rx/tx delays bit for modes
differents that RGMII*ID. Due to this, ethernet is not working anymore
on my guruplug server +. This patch is fixing that.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel doesn't have a symbol called BCM63XX. There is a symbol
BCM63XX_ENET (introduced in 9b1fc55a05, 6 weeks after 09bb9aa0ed that
introduced BCM63XX_PHY), but the driver compiles without that, too.
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
MODULE_DEVICE_TABLE only expands to something if it's compiled
for a module. So when building-in support for the phys, the
mdio_device_id tables are unused. Marking them with __maybe_unused
fixes the following warnings:
drivers/net/phy/bcm63xx.c:134: warning: 'bcm63xx_tbl' defined but not used
drivers/net/phy/broadcom.c:933: warning: 'broadcom_tbl' defined but not used
drivers/net/phy/cicada.c:162: warning: 'cicada_tbl' defined but not used
drivers/net/phy/davicom.c:222: warning: 'davicom_tbl' defined but not used
drivers/net/phy/et1011c.c:114: warning: 'et1011c_tbl' defined but not used
drivers/net/phy/icplus.c:137: warning: 'icplus_tbl' defined but not used
drivers/net/phy/lxt.c:226: warning: 'lxt_tbl' defined but not used
drivers/net/phy/marvell.c:724: warning: 'marvell_tbl' defined but not used
drivers/net/phy/micrel.c:234: warning: 'micrel_tbl' defined but not used
drivers/net/phy/national.c:154: warning: 'ns_tbl' defined but not used
drivers/net/phy/qsemi.c:141: warning: 'qs6612_tbl' defined but not used
drivers/net/phy/realtek.c:82: warning: 'realtek_tbl' defined but not used
drivers/net/phy/smsc.c:257: warning: 'smsc_tbl' defined but not used
drivers/net/phy/ste10Xp.c:135: warning: 'ste10Xp_tbl' defined but not used
drivers/net/phy/vitesse.c:195: warning: 'vitesse_tbl' defined but not used
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
On resume, before starting the PAL state machine, check if the
adjust_link() method is well supplied. If not, this would lead to a
NULL pointer dereference in the phy_state_machine() function.
This scenario can happen if the Ethernet driver call manually the PHY
functions instead of using the PAL state machine. The mv643xx_eth driver
is a such example.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net/ipv4: Eliminate kstrdup memory leak
net/caif/cfrfml.c: use asm/unaligned.h
ax25: missplaced sock_put(sk)
qlge: reset the chip before freeing the buffers
l2tp: test for ethernet header in l2tp_eth_dev_recv()
tcp: select(writefds) don't hang up when a peer close connection
tcp: fix three tcp sysctls tuning
tcp: Combat per-cpu skew in orphan tests.
pxa168_eth: silence gcc warnings
pxa168_eth: update call to phy_mii_ioctl()
pxa168_eth: fix error handling in prope
pxa168_eth: remove unneeded null check
phylib: Fix race between returning phydev and calling adjust_link
caif-driver: add HAS_DMA dependency
3c59x: Fix deadlock between boomerang_interrupt and boomerang_start_tx
qlcnic: fix poll implementation
netxen: fix poll implementation
bridge: netfilter: fix a memory leak
It is possible that phylib will call adjust_link before returning
from {,of_}phy_connect(), which may cause the following [very rare,
though] oops upon reopening the device:
Unable to handle kernel paging request for data at address 0x0000024c
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT SMP NR_CPUS=2 LTT NESTING LEVEL : 0
P1021 RDB
Modules linked in:
NIP: c0345dac LR: c0345dac CTR: c0345d84
TASK = dffab6b0[30] 'events/0' THREAD: c0d24000 CPU: 0
[...]
NIP [c0345dac] adjust_link+0x28/0x19c
LR [c0345dac] adjust_link+0x28/0x19c
Call Trace:
[c0d25f00] [000045e1] 0x45e1 (unreliable)
[c0d25f30] [c036c158] phy_state_machine+0x3ac/0x554
[...]
Here is why. Drivers store phydev in their private structures, e.g.
gianfar driver:
static int init_phy(struct net_device *dev)
{
...
priv->phydev = of_phy_connect(...);
...
}
So that adjust_link could retrieve it back:
static void adjust_link(struct net_device *dev)
{
...
struct phy_device *phydev = priv->phydev;
...
}
If the device has been opened before, then phydev->state is set to
PHY_HALTED (or undefined if the driver didn't call phy_stop()).
Now, phy_connect starts the PHY state machine before returning phydev to
the driver:
phy_start_machine(phydev, NULL);
if (phydev->irq > 0)
phy_start_interrupts(phydev);
return phydev;
The time between 'phy_start_machine()' and 'return phydev' is undefined.
The start machine routine delays execution for 1 second, which is enough
for most cases. But under heavy load, or if you're unlucky, it is quite
possible that PHY state machine will execute before phy_connect()
returns, and so adjust_link callback will try to dereference phydev,
which is not yet ready.
To fix the issue, simply initialize the PHY's state to PHY_READY during
phy_attach(). This will ensure that phylib won't call adjust_link before
phy_start().
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix phy.c kernel-doc notation:
Warning(drivers/net/phy/phy.c:313): No description found for parameter 'ifr'
Warning(drivers/net/phy/phy.c:313): Excess function parameter 'mii_data' description in 'phy_mii_ioctl'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1443 commits)
phy/marvell: add 88ec048 support
igb: Program MDICNFG register prior to PHY init
e1000e: correct MAC-PHY interconnect register offset for 82579
hso: Add new product ID
can: Add driver for esd CAN-USB/2 device
l2tp: fix export of header file for userspace
can-raw: Fix skb_orphan_try handling
Revert "net: remove zap_completion_queue"
net: cleanup inclusion
phy/marvell: add 88e1121 interface mode support
u32: negative offset fix
net: Fix a typo from "dev" to "ndev"
igb: Use irq_synchronize per vector when using MSI-X
ixgbevf: fix null pointer dereference due to filter being set for VLAN 0
e1000e: Fix irq_synchronize in MSI-X case
e1000e: register pm_qos request on hardware activation
ip_fragment: fix subtracting PPPOE_SES_HLEN from mtu twice
net: Add getsockopt support for TCP thin-streams
cxgb4: update driver version
cxgb4: add new PCI IDs
...
Manually fix up conflicts in:
- drivers/net/e1000e/netdev.c: due to pm_qos registration
infrastructure changes
- drivers/net/phy/marvell.c: conflict between adding 88ec048 support
and cleaning up the IDs
- drivers/net/wireless/ipw2x00/ipw2100.c: trivial ipw2100_pm_qos_req
conflict (registration change vs marking it static)
Marvell 88ec048 is a derivative of its 88e1121r device. From the programmer's
perspective, the one major difference is the addition of an additional control
bit in Page 2 Register 16 - used to control the padding of odd nibble
preambles.
This patch adds support for this new device, while inheriting as much code as
possible from the existing 88e1121r implementation.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for RGMII RX/TX delay configuration on marvell 88e1121
and derivatives. With this patch, PHY_INTERFACE_MODE_RGMII_*ID modes are now
supported on these devices.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new networking option to allow hardware time stamps
from PHY devices. When enabled, likely candidates among incoming and
outgoing network packets are offered to the PHY driver for possible
time stamping. When accepted by the PHY driver, incoming packets are
deferred for later delivery by the driver.
The patch also adds phylib driver methods for the SIOCSHWTSTAMP ioctl
and callbacks for transmit and receive time stamping. Drivers may
optionally implement these functions.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_mii_ioctl() function unnecessarily throws away the original ifreq.
We need access to the ifreq in order to support PHYs that can perform
hardware time stamping.
Two maverick drivers filter the ioctl commands passed to phy_mii_ioctl().
This is unnecessary since phylib will check the command in any case.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves the various known Marvell PHY IDs to include/linux/marvell_phy.h
along with dev_flags definitions for use by the driver.
I then added a flag that changes the PHY init code to setup the LEDs
config to the values needed to operate a dns323 rev C1 NAS.
I moved the existing "resistance" flag to the .h as well, though I've
been unable to find whoever sets this to convert it to use that constant.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Hello all:
This patch fixes what Ben mentioned, namely duplicated ids.
From: David J. Choi <david.choi@micrel.com>
Body of the explanation: This patch has changes as followings;
-support the interrupt from phy devices from Micrel Inc.
-support more phy devices, ks8737, ks8721, ks8041, ks8051 from Micrel.
-remove vsc8201 because this device was used only internal test at Micrel.
Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We started getting:
WARNING: vmlinux.o(.data+0x20bd0): Section mismatch in reference from
the variable octeon_mdiobus_driver to the function
.init.text:octeon_mdiobus_probe()
This fixes it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e13647c1 (phylib: Add support for the LXT973 phy.) added a new ID
but neglected to also add it to the MODULE_DEVICE_TABLE.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 5241 PHY ID to the broadcom module.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all PHY IDs to brcmphy.h header for completeness and unification of code.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements a work around for Erratum 5, "3.3 V Fiber Speed
Selection." If the hardware wiring does not respect this erratum, then
fiber optic mode will not work properly.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
It also does not remove null void functions with return.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
with some cleanups by hand.
Compile tested x86 allmodconfig only.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Fix FDDI and TR config checks in ipv4 arp and LLC.
IPv4: unresolved multicast route cleanup
mac80211: remove association work when processing deauth request
ar9170: wait for asynchronous firmware loading
ipv4: udp: fix short packet and bad checksum logging
phy: Fix initialization in micrel driver.
sctp: Fix a race between ICMP protocol unreachable and connect()
veth: Dont kfree_skb() after dev_forward_skb()
IPv6: fix IPV6_RECVERR handling of locally-generated errors
net/gianfar: drop recycled skbs on MTU change
iwlwifi: work around passive scan issue
Missing name string in ks8001_driver, so we crash on register.
Reported-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the first version of phy driver from Micrel Inc.
Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases the mdio bus is not enabled at the time of probing.
This prevents anything from working, so we will enable it before
trying to use it, and disable it when the driver is removed.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
To: netdev@vger.kernel.org
To: gregkh@suse.de
Patchwork: http://patchwork.linux-mips.org/patch/1090/
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We don't use the normal hotplug mechanism because it doesn't work. It will
load the module some time after the device appears, but that's not good
enough for us -- we need the driver loaded _immediately_ because otherwise
the NIC driver may just abort and then the phy 'device' goes away.
[bwh: s/phy/mdio/ in module alias, kerneldoc for struct mdio_device_id]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
IEEE 802.3ae clause 45 specifies a somewhat modified MDIO protocol
for use by 10GIGE phys. The main change is a 21 bit address split into
a 5 bit device ID and a 16 bit register offset. The definition is designed
so that normal and extended devices can run on the same MDIO bus.
Extend mdio-bitbang to do the new protocol. At the MDIO bus level the
protocol is requested by or'ing MII_ADDR_C45 into the register offset.
Make phy_read/phy_write/etc pass a full 32 bit register offset.
This does not attempt to make the phy layer support C45 style PHYs, just
to provide the MDIO bus support.
Tested against a Broadcom 10GE phy with ID 0x206034, and several
Broadcom 10/100/1000 Phys in normal mode.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch pushes phylib definitions out to phylib headers. For phy
IDs, this removes some code duplication.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers do this in them manually. Now they can use this function.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 541cd3ee00 ("phylib: Fix deadlock
on resume") caused TI DaVinci EMAC ethernet driver to oops upon resume:
PM: resume of devices complete after 237.098 msecs
Restarting tasks ... done.
kernel BUG at kernel/workqueue.c:354!
Unable to handle kernel NULL pointer dereference at virtual address 00000000
[...]
Backtrace:
[<c002c598>] (__bug+0x0/0x2c) from [<c0052a54>] (queue_delayed_work_on+0x74/0xf8)
[<c00529e0>] (queue_delayed_work_on+0x0/0xf8) from [<c0052b30>] (queue_delayed_work+0x2c/0x30)
The oops pops up because TI DaVinci EMAC driver detaches PHY on
suspend and attaches it back on resume. Attaching makes phylib call
phy_start_machine() that initializes a workqueue. On the other hand,
PHY's resume routine will call phy_start_machine() again, and that
will cause the oops since we just destroyed the already scheduled
workqueue.
This patch fixes the issue by moving workqueue initialization to
phy_device_create().
p.s. We don't see this oops with ucc_geth and gianfar drivers because
they perform a fine-grained suspend, i.e. they just stop the PHYs
without detaching.
Reported-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
sky2: Fix oops in sky2_xmit_frame() after TX timeout
Documentation/3c509: document ethtool support
af_packet: Don't use skb after dev_queue_xmit()
vxge: use pci_dma_mapping_error to test return value
netfilter: ebtables: enforce CAP_NET_ADMIN
e1000e: fix and commonize code for setting the receive address registers
e1000e: e1000e_enable_tx_pkt_filtering() returns wrong value
e1000e: perform 10/100 adaptive IFS only on parts that support it
e1000e: don't accumulate PHY statistics on PHY read failure
e1000e: call pci_save_state() after pci_restore_state()
netxen: update version to 4.0.72
netxen: fix set mac addr
netxen: fix smatch warning
netxen: fix tx ring memory leak
tcp: update the netstamp_needed counter when cloning sockets
TI DaVinci EMAC: Handle emac module clock correctly.
dmfe/tulip: Let dmfe handle DM910x except for SPARC on-board chips
ixgbe: Fix compiler warning about variable being used uninitialized
netfilter: nf_ct_ftp: fix out of bounds read in update_nl_seq()
mv643xx_eth: don't include cache padding in rx desc buffer size
...
Fix trivial conflict in drivers/scsi/cxgb3i/cxgb3i_offload.c
SMSC Ethernet Transceivers (LAN88710, LAN8710, LAN8720, LAN8187,
LAN8700, LAN83C185) provide a mechanism to conserve power when
the device is not connected to an active link partner
(Energy Detect Mode).
So this patch enables the Energy Detect power-down mode
for these Transceivers.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hibernation assumes power loss, we should fully reinitialize
PHYs (including platform fixups), as if PHYs were just attached.
This patch factors phy_init_hw() out of phy_attach_direct(), then
converts mdio_bus to dev_pm_ops and adds an appropriate restore()
callback.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes kernel hangs on resume with the following trace:
ucc_geth e0102000.ucc: resume
INFO: task bash:1764 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
bash D 0fecf43c 0 1764 1763 0x00000000
Call Trace:
[cf9a7c10] [c0012868] ret_from_except+0x0/0x14 (unreliable)
--- Exception: cf9a7ce0 at __switch_to+0x4c/0x6c
LR = 0xcf9a7cc0
[cf9a7cd0] [c0008c14] __switch_to+0x4c/0x6c (unreliable)
[cf9a7ce0] [c028bcfc] schedule+0x158/0x260
[cf9a7d10] [c028c720] __mutex_lock_slowpath+0x80/0xd8
[cf9a7d40] [c01cf388] phy_stop+0x20/0x70
[cf9a7d50] [c01d514c] ugeth_resume+0x6c/0x13c
[...]
Here is why.
On suspend:
- PM core starts suspending devices, ucc_geth_suspend gets called;
- ucc_geth calls phy_stop() on suspend. Note that phy_stop() is
mostly asynchronous so it doesn't block ucc_geth's suspend routine,
it just sets PHY_HALTED state and disables PHY's interrupts;
- Suddenly the state machine gets scheduled, it grabs the phydev->lock
mutex and tries to process the PHY_HALTED state, so it calls
phydev->adjust_link(phydev->attached_dev). In ucc_geth case
adjust_link() calls msleep(), which reschedules the code flow back to
PM core, which now finishes suspend and so we end up sleeping with
phydev->lock mutex held.
On resume:
- PM core starts resuming devices (notice that nobody rescheduled
the state machine yet, so the mutex is still held), the core calls
ucc_geth's resume routine;
- ucc_geth_resume restarts the PHY with phy_stop()/phy_start()
sequence, and the phy_*() calls are trying to grab the phydev->lock
mutex. Here comes the deadlock.
This patch fixes the issue by stopping the state machine on suspend
and starting it again on resume.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
bnx2: Fix bnx2_netif_stop() merge error.
gianfar: Fix bit definitions of IMASK_GRSC and IMASK_GTSC
gianfar: Fix stats support
gianfar: Fix a filer bug
bnx2: fixing a timout error due not refreshing TX timers correctly
can/at91: don't check platform_get_irq's return value against zero
mISDN: use DECLARE_COMPLETION_ONSTACK for non-constant completion
bnx2: reset_task is crashing the kernel. Fixing it.
ipv6: fix an oops when force unload ipv6 module
TI DaVinci EMAC: Fix MDIO bus frequency configuration
e100: Fix broken cbs accounting due to missing memset.
broadcom: bcm54xx_shadow_read() errors ignored in bcm54xx_adjust_rxrefclk()
e1000e: LED settings in EEPROM ignored on 82571 and 82572
netxen: use module parameter correctly
netns: fix net.ipv6.route.gc_min_interval_ms in netns
Bluetooth: Prevent ill-timed autosuspend in USB driver
Bluetooth: Fix L2CAP locking scheme regression
Bluetooth: Ack L2CAP I-frames before retransmit missing packet
Bluetooth: Fix unset of RemoteBusy flag for L2CAP
Bluetooth: Fix PTR_ERR return of wrong pointer in hidp_setup_hid()
If not signed read errors are ignored.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Octeon SOC has two types of Ethernet ports, each type with its own
driver. However, the PHYs for all the ports are controlled by a
common MDIO bus. Because the mdio driver is not associated with a
particular driver, but is instead a system level resource, we create s
stand-alone driver for it.
As for the driver, we put the register definitions in
arch/mips/include/asm/octeon where most of the other Octeon register
definitions live. This is a platform driver with the platform device
for "mdio-octeon" being registered in the platform startup code.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Only files where David Miller is the primary git-signer.
wireless, wimax, ixgbe, etc are not modified.
Compile tested x86 allyesconfig only
Not all files compiled (not x86 compatible)
Added a few > 80 column lines, which I ignored.
Existing checkpatch complaints ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following warning:
WARNING: drivers/net/phy/built-in.o(.devexit.text+0x70): Section mismatch in reference from the function .mdio_gpio_bus_destroy() to the function .devinit.text:.mdio_gpio_bus_deinit()
The function __devexit .mdio_gpio_bus_destroy() references
a function __devinit .mdio_gpio_bus_deinit().
This is often seen when error handling in the exit function
uses functionality in the init path.
The fix is often to remove the __devinit annotation of
.mdio_gpio_bus_deinit() so it may be used outside an init section.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to disable the TXC and RXC reference clocks if link
is not available.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an RXC auto power-down feature to the code that supports
the gphys.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5785 does not use the RXC reference clock. Turning it off is
desirable as it saves power.
By default, the 50610 enables the RXC reference clock and the 50610M
disables it. Presumably this is one of the reasons why the hardware
architect chose one over the other.
Adding a "rx reference clock disable" flag is not the ideal way to
describe the option, as it would force the MAC using a 50610M to set
the flag. Ideally we want the flags to represent opt-in behavior that
deviates from hardware defaults. Furthermore, the lack of a
"disable" flag implies that the requester wants the rx reference clock
enabled, which doesn't necessarily follow.
By presenting the option as a passive statement (rx reference clock
unused) rather than a command, I hope to convey an opt-in option to
disable the rx reference clock that falls back to hardware defaults if
not set. A secondary benefit of this is that it keeps the
intelligence about phy defaults in the broadcom module where it belongs
and allows the broadcom module more latitude should a bug arise.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Auto power-down (APD) support is a power-saving feature. It should be
selectively enabled since it might expose MAC bugs. This patch changes
the code to enable APD only if the PHY_BRCM_AUTO_PWRDWN_ENABLE flag is
set. The tg3 driver was changed to set this bit.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom 50610M parts changed the default definitions of the RGMII mode
shadow register. The 5785 needs the RGMII mode selection bits [4:3]
cleared.
The default value of the remaining bits in this register are zero.
Rather than unnecessarily burn an extra bit in the dev_flags member in
an attempt to enumerate all possible combinations, this patch take a
more course grained approach and labels the option as "clear all bits".
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves all the dev_flags enumerations outside the broadcom.c
file to include/linux/brcmphy.h. The existing flags were not used yet
and have been re-enumerated to avoid conflicts.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a 50610 or 50610M is paired against particular remote partners,
link is slow to come up. This patch works around the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch consolidates the code that requires the SMDSP clock to be
enabled into a single function that (hopefully) makes the dependency
obvious.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some OF platform drivers are missing module device tables, so they won't
load automatically on boot. This patch fixes the issue by adding proper
MODULE_DEVICE_TABLE() macros to the drivers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to specs, when auto-negotiation is disabled, Marvell PHYs need
a software reset after changing speed/duplex forcing bits. Otherwise,
the modified bits have no effect.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error handling code following a kzalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_ioctl() already checks capable(CAP_NET_ADMIN) before calling the
driver's implementation of MDIO ioctls.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This brings the 57780's phy into IEEE compliance by suppressing the
common mode oscillation.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the AC131 fast ethernet transceiver.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the BCM50610M phy ID.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to the fs_enet driver aa73832c5a
("net: Rework fs_enet driver to use of_mdio infrastructure")
cause kernel crashes when using the mdio-ofgpio driver.
This patch replicates similar changes made to the fs_enet mii-bitbang
drivers. It has been tested on a custom mpc8280 based board using an
NFS mounted root.
Signed-off-by: Mark Ware <mware@elphinstone.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't forget to unlock a mutex in phy_scan_fixups on a fail path.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY_HALTED state disables phydev->link, but the link will not be
updated upon entering PHY_RESUMING. Add a call to phy_read_status() to
update the link before entering PHY_RUNNING. If the link is not up at
this point, enter the PHY_NOLINK state instead.
Also, when transitioning from PHY_RESUMING to PHY_RUNNING, calls to
netif_carrier_on() and phydev->adjust_link() are missing. Add the calls
similar to the other transitions to PHY_RUNNING.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc parameter name in phy_device.c.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable fiber/copper auto selection for Marvell m88e1111 SGMII support.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add phy_connect_direct() and phy_attach_direct() functions so that
drivers can use a pointer to the phy_device instead of trying to determine
the phy's bus_id string.
This patch is useful for OF device tree descriptions of phy devices where
the driver doesn't need or know what the bus_id value in order to get a
phy_device pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes changes in preparation for supporting open firmware
device tree descriptions of MDIO busses. Changes include:
- Cleanup handling of phy_map[] entries; they are already NULLed when
registering and so don't need to be re-cleared, and it is good practice
to clear them out when unregistering.
- Split phy_device registration out into a new function so that the
OF helpers can do two stage registration (separate allocation and
registration steps).
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit a390d1f3 ("phylib: convert state_queue work to
delayed_work") missed converting 'expires' value to 'delay' value.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add did_interrupt() function to check if a PHY port
really caused an interrupt. This is needed in the case
of shared PHY interrupt pin configuration to stop
interrupt event processing for PHY ports which didn't
cause an interrupt.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 88E1121R Dual PHY device can be hardware-configured
to use shared interrupt pin for both PHY ports. For such
PHY configurations using shared PHY interrupt phy_interrupt()
handler will also schedule a work for PHY port which didn't
cause an interrupt.
This patch adds a possibility for PHY drivers to provide
did_interrupt() function which reports if the PHY (or a PHY
port in a multi-PHY device) generated an interrupt. This
function is called in phy_change() as phy_change() shouldn't
proceed if it is invoked for a PHY which didn't cause an
interrupt. So check for interrupt originator in phy_change()
to allow early-out.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Marvell M88E1121R Dual GigE PHY
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_device_register_simple() returns ERR_PTR() and not NULL.
Found by smatch (http://repo.or.cz/w/smatch.git). Compile tested.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a fairly common operation to have a pointer to a work and to need a
pointer to the delayed work it is contained in. In particular, all
delayed works which want to rearm themselves will have to do that. So it
would seem fair to offer a helper function for this operation.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LAN8710 and LAN8720 are two new 10/100 ethernet PHY models. The two
share the same phy id, this patch adds it to the smsc phy driver.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It closes a race in phy_stop_machine when reprogramming of phy_timer
(from phy_state_machine) happens between del_timer_sync and cancel_work_sync.
Without this change it could lead to crash if phy_device would be freed after
phy_stop_machine (timer would fire and schedule freed work).
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdc pin should always be output. Initialize it as output,
so each board code does not need to do this.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>
In most cases (e.g. PCI drivers) MDIO and MAC controllers are
represented by the same device. But for SOC ethernets we have
separate devices. So, in SOC case, checking whether MDIO
controller may wakeup is not only makes little sense, but also
prevents us from doing per-netdevice wakeup management.
This patch reworks suspend/resume code so that now it checks
for net device's wakeup flags, not MDIO controller's ones.
Each netdevice should manage its wakeup flags, and phylib will
decide whether suspend an attached PHY or not.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All supported SMSC PHYs implement the standard "power down" bit 11 of
BMCR, so this patch adds support using the generic genphy_{suspend,resume}
functions.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suspend/resume routines check for phydrv != NULL, but that is
wrong because "phydrv" comes from container_of(drv). If drv is NULL,
then container_of(drv) will return non-NULL result, and the checks
won't work.
The Freescale TBI PHYs are driver-less, so "drv" is NULL, and that
leads to the following oops:
Unable to handle kernel paging request for data at address 0xffffffe4
Faulting instruction address: 0xc0215554
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c0215554] mdio_bus_suspend+0x34/0x70
LR [c01cc508] suspend_device+0x258/0x2bc
Call Trace:
[cfad3da0] [cfad3db8] 0xcfad3db8 (unreliable)
[cfad3db0] [c01cc508] suspend_device+0x258/0x2bc
[cfad3dd0] [c01cc62c] dpm_suspend+0xc0/0x140
[cfad3e20] [c01cc6f4] device_suspend+0x48/0x5c
[cfad3e40] [c0068dd8] suspend_devices_and_enter+0x8c/0x148
[cfad3e60] [c00690f8] enter_state+0x100/0x118
[cfad3e80] [c00691c0] state_store+0xb0/0xe4
[cfad3ea0] [c018c938] kobj_attr_store+0x24/0x3c
[cfad3eb0] [c00ea9a8] flush_write_buffer+0x58/0x7c
[cfad3ed0] [c00eadf0] sysfs_write_file+0x58/0xa0
[cfad3ef0] [c009e810] vfs_write+0xb4/0x16c
[cfad3f10] [c009ed40] sys_write+0x4c/0x90
[cfad3f40] [c0014954] ret_from_syscall+0x0/0x38
[...]
This patch fixes the issue, plus removes unneeded parentheses
and fixes indentation level in mdio_bus_suspend().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
both pdata->mdc and pdata->mdio are unsigned. Notice a negative
return value.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Freescale on-chip TBI PHYs reports PHY ID as 0x0, but as of
commit 3ee82383f0
Author: Giulio Benetti <giulio.benetti@micronovasrl.com>
Date: Thu Nov 13 21:53:13 2008 +0000
phy: fix phy address bug
PHYID returns 0xffff and not 0xffffffff when not found and in some
case(at91sam9263) 0x0. Maybe this patch could be useful.
phy_device.c treats PHY ID == 0x0 as bogus IDs, and that results in
gianfar driver failure to see the TBI PHYs. This code snippet triggers:
if (!priv->tbiphy) {
printk(KERN_WARNING "SGMII mode requires that the device "
"tree specify a tbi-handle\n");
return;
}
Although tbi-handle is specified in the device tree.
Btw, technically PHY ID == 0x0 is a valid ID (if we ever see a PHY
manufactured by Xerox :-).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHYLIB mdio code has more problems in error paths:
- mdiobus_release can be called before bus->state is set to
MDIOBUS_REGISTERED
- mdiobus_scan allocates resources which need to be freed
- the comment is wrong, the resistors used are actually pull-ups.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
kernel BUG at drivers/net/phy/mdio_bus.c:165!
Unable to handle kernel NULL pointer dereference at virtual address 00000000
How?
mdiobus_alloc() sets bus->state = MDIOBUS_ALLOCATED.
mdiobus_register() sets bus->state = MDIOBUS_REGISTERED but then can
fail (mdiobus_scan()) returning an error to the caller.
The caller aborts correctly with mdiobus_free() which does:
if (bus->state == MDIOBUS_ALLOCATED) {
kfree(bus);
return;
}
BUG_ON(bus->state != MDIOBUS_UNREGISTERED);
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_setup_forced hasn't actually reset the PHY for a long time,
but a comment to that effect remained in the code, so code continued
to act as if it *had* reset the PHY, and called the necessary fixup
functions to respond to a PHY reset. With no reset, those functions
are no longer needed, so we remove them.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds LSI ET1011C PHY driver.
This driver is used by TI DM646x EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the STMicroelectronics ste10xp PHY device driver.
It supports both the ste100p and the ste101p devices.
Suspend/resume alredy added.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the power management support into the physical
abstraction layer.
Suspend and resume functions respectively turns on/off the bit 11
into the PHY Basic mode control register.
Generic PHY device starts supporting PM.
In order to support the wake-on LAN and avoid to put in power down
the PHY device, the MDIO is aware of what the Ethernet device wants to do.
Voluntary, no CONFIG_PM defines were added into the sources.
Also generic suspend/resume functions are exported to allow
other drivers use them (such as genphy_config_aneg etc.).
Within the phy_driver_register function, we need to remove the
memset. It overrides the device driver owner and it is not good.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the PHY device driver for the National Semiconductor
DP83865 Gig PHYTER.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY is mostly compatible with the existing VSC8244 PHY. The init sequence
is different and the interrupt mask lacks some bits present in the VSC8244.
Rather than making a copy of the existing VSC234x config_intr function and
change one constant, I modify it to select the interrupt mask based on
which driver is calling it. This lets it be used by both drivers.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 57780 PHY ID to the broadcom module.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the case when the phy_ids is mostly Fs and in some case 0x0
due to broken hardware.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous patch, 51e2a3846e, made
genphy_config_aneg() not restart aneg by calling genphy_restart_aneg() if
the advertisement hadn't changed.
But, genphy_restart_aneg() doesn't just restart aneg, it may also *enable*
aneg or un-isolate the PHY from the MII (those functions are controlled by
the same register). The code to avoid calling genphy_restart_aneg() didn't
consider this.
So, modify genphy_config_aneg() to also check if the PHY needs to have aneg
enabled or be un-isolated before deciding not to restart aneg.
This caused a problem with certain Davicom PHYs, as that driver isolates
the PHY (why?) before calling genphy_config_aneg() and expects the PHY to
be un-isolated by that function.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Reported-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
make mdio-gpio work with non OpenFirmware gpio implementation.
Aditional changes to mdio-gpio:
- use gpio_request() and gpio_free()
- place irq[] array in struct mdio_gpio_info
- add module description, author and license
- add note about compiling this driver as module
- rename mdc and mdio function (were ugly names)
- change MII to MDIO in bus name
- add __init __exit to module (un)loading functions
- probe fails if no phys added to the bus
- kzalloc bitbang with sizeof(*bitbang)
Changes since v3:
- keep bus naming "%x" to be compatible with existing drivers.
Changes since v2:
- more #ifdefs reduction
- platform driver will be registered on OF platforms also
- unified platform and OF bus_id to phy%i
Changes since v1:
- removed NO_IRQ
- reduced #idefs
Laurent, please test this driver under OF.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHYID returns 0xffff and not 0xffffffff when not found and in some
case(at91sam9263) 0x0. Maybe this patch could be useful.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will add support for the Marvell 88E1118 PHY which supports gigabit ethernet among other things.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 46abc02175 ("phylib: give mdio
buses a device tree presence") added a call to device_unregister() in
a situation where the caller did not intend for the device to be
freed yet, but apart from just unregistering the device from the
system, device_unregister() does an additional put_device() that is
intended to free it.
The right function to use in this situation is device_del(), which
unregisters the device from the system like device_unregister() does,
but without dropping the reference count an additional time.
Bug report from Bryan Wu <cooloney@kernel.org>.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attached is a driver for SMSC's LAN911x and LAN921x families of embedded
ethernet controllers.
There is an existing smc911x driver in the tree; this is intended to
replace it. Dustin McIntire (the author of the smc911x driver) has
expressed his support for switching to this driver.
This driver contains workarounds for all known hardware issues, and has
been tested on all flavours of the chip on multiple architectures.
This driver now uses phylib, so this patch also adds support for the
device's internal phy
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Bahadir Balban <Bahadir.Balban@arm.com>
Signed-off-by: Dustin Mcintire <dustin@sensoria.com>
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds the BCM50610 to the list of phys supported by the
broadcom driver.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the expansion register access routines a little more
formal. They will be used by the following bcm50610 support patch.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds flow control support to Broadcom phys.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core now has this helper function, so might as well use it
instead of forcing the phy code to roll their own version.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the following build error caused by
commit ed94493fb3
(mv643xx_eth: convert to phylib):
<-- snip -->
...
Building modules, stage 2.
MODPOST 1280 modules
ERROR: "genphy_restart_aneg" [drivers/net/mv643xx_eth.ko] undefined!
...
make[2]: *** [__modpost] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warning, missing description:
Warning(lin2627-g3-kdocfixes//drivers/net/phy/mdio_bus.c:63): No description found for parameter 'd'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. arch/powerpc/platforms/pasemi/gpio_mdio.c also needs to be
converted over to mdiobus_{alloc,free}().
2. drivers/net/phy/fixed.c used to embed a struct mii_bus into its
struct fixed_mdio_bus and then use container_of() to go from the
former to the latter. Since mii bus structures are no longer
embedded, we need to do something like use the mii bus private
pointer to go from mii_bus to fixed_mdio_bus instead.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mdiobus_{read,write} routines to allow direct reading/writing
of registers on an mii bus without having to go through the PHY
abstraction, and make phy_{read,write} use these primitives.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the mdio_bus class, and give each 'struct mii_bus' its own
'struct device', so that mii_bus objects are represented in the device
tree and can be found by querying the device tree.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces mdiobus_alloc() and mdiobus_free(), and
makes all mdio bus drivers use these functions to allocate their
struct mii_bus'es dynamically.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Andy Fleming <afleming@freescale.com>
In preparation of giving mii_bus objects a device tree presence of
their own, rename struct mii_bus's ->dev argument to ->parent, since
having a 'struct device *dev' that points to our parent device
conflicts with introducing a 'struct device dev' representing our own
device.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Andy Fleming <afleming@freescale.com>
This way the phy layer will respond to a change in phy state immediately,
instead of up to one second later when the state machine timer runs.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY's aneg is configured and restarted whenever the link is brought up,
e.g. when DHCP is started after the kernel has booted. This can take the
link down for several seconds while auto-negotiation is redone.
If the advertised features haven't changed, then it shouldn't be necessary
to bring down the link and start auto-negotiation over again.
genphy_config_advert() is enhanced to return 0 when the advertised features
haven't been changed and >0 when they have been.
genphy_config_aneg() then uses this information to not call
genphy_restart_aneg() if there has been no change.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the SIOCGMIIPHY case fall through properly (it is supposed
to not only return the ID of the default PHY but also to read from
that PHY), and make phy_mii_ioctl() return the same error code as
generic_mii_ioctl() in case of an unsupported operation.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch splits the bus scanning code in mdiobus_register() off
into a separate function, and makes this function available for
calling from external code. This allows incrementally scanning an
mii bus, e.g. as information about which addresses are 'safe' to
scan becomes available.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
MII_M1111_HWCFG_FIBER_COPPER_RES is a bit of MII_M1111_PHY_EXT_SR, not
MII_M1111_PHY_EXT_CR.
Signed-off-by: Wang Jian <lark@linux.net.cn>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The 27.15 bit (MII_M1111_HWCFG_FIBER_COPPER_AUTO) is disable bit. When
set to 1, copper/fiber auto selection is disabled. The current code
to enable but actually disable auto selection.
Signed-off-by: Wang Jian <lark@linux.net.cn>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
{alloc,free}_mdio_bitbang() are not exported while they are used in
mdio-ofgpio driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds an MDIO bitbang driver that uses the GPIO library and its
OF bindings to access the bus I/Os.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit cac1f3c8 factored out the code for get_phy_id so that it
could be reused in multiple places. Turns out that some of the
users can be modular, so we need to export this symbol as well.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add Broadcom PHYs supported missing from the description.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Configure the BCM5482S secondary SerDes for 1000Base-X mode when the
appropriate dev_flags are passed in to phy_connect(). This is
needed when the PHY is used for fiber and backplane connections.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PHYLIB was first marked as BROKEN on S390, then the enclosing menu marked
as non-S390, then the two dependencies merged with the conversion to
menuconfig. Reduce to non-S390.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Declared some things static, declared some things in the header.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support for two additional SMSC PHY models with identical interrupt
source and mask registers to the LAN83C185
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Several models of SMSC PHY have the same interrupt status and mask
registers as the LAN83C185, so these functions can service multiple
different PHY drivers.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
David S. Miller