Based on the musb ug, force_host bit is allowed to be set along with
force_hs or force_fs bit.
It could help to implement forced host mode via testmode on Nokia N900.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch just uses the resource-managed extcon API when registering
the extcon notifier.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On da8xx, VBUS is not maintained during suspend when musb is in host mode.
On resume, all the connected devices will be disconnected and then will
be enumerated again.
This happens because MUSB_DEVCTL is cleared during suspend.
Use the quirk MUSB_PRESERVE_SESSION to preseve MUSB_DEVCTL during suspend.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On da8xx, VBUS is not maintained during suspend when musb is in host mode.
On resume, all the connected devices will be disconnected and then will
be enumerated again.
This happens because MUSB_DEVCTL is cleared during suspend.
Add a quirk to not clear MUSB_DEVCTL and then preserve the session during
a suspend.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement PM methods specifics for da8xx glue.
The only thing to do is to power off the phy.
As the registers are in retention during suspend,
there is no need to save them.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb_generic_disable() only has two lines of code. So remove it and let
the callers directly call those two lines.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DA8xx driver is registering and using the CPPI 3.0 DMA controller but
actually, the DA8xx has a CPPI 4.1 DMA controller.
Remove the CPPI 3.0 quirk and methods.
Fixes: f8e9f34f80 ("usb: musb: Fix up DMA related macros")
Fixes: 7f6283ed6f ("usb: musb: Set up function pointers for DMA")
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While testing musb host mode cable plugging on a BeagleBone, I came across this
error:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd1dcfc60
...
[<bf668390>] (musb_default_readb [musb_hdrc]) from [<bf668578>] (musb_irq_work+0x1c/0x180 [musb_hdrc])
[<bf668578>] (musb_irq_work [musb_hdrc]) from [<c0156554>] (process_one_work+0x2b4/0x808)
[<c0156554>] (process_one_work) from [<c015767c>] (worker_thread+0x3c/0x550)
[<c015767c>] (worker_thread) from [<c015d568>] (kthread+0x104/0x148)
[<c015d568>] (kthread) from [<c01078d0>] (ret_from_fork+0x14/0x24)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 467d5c9807 ("usb: musb: Implement session bit based runtime PM for
musb-core") started implementing musb generic runtime PM support by
introducing devctl register session bit based state control.
This caused a regression where if a USB mass storage device is connected
to a USB hub, we can get:
usb 1-1: reset high-speed USB device number 2 using musb-hdrc
usb 1-1: device descriptor read/64, error -71
usb 1-1.1: new high-speed USB device number 4 using musb-hdrc
This is because before the USB storage device is connected, musb is
in OTG_STATE_A_SUSPEND. And we currently only set need_finish_resume
in musb_stage0_irq() and the related code calling finish_resume_work
in musb_resume() and musb_runtime_resume() never gets called.
To fix the issue, we can call schedule_delayed_work() directly in
musb_stage0_irq() to have finish_resume_work run.
And we should no longer never get interrupts when when suspended.
We have changed musb to no longer need pm_runtime_irqsafe().
The need_finish_resume flag was added in commit 9298b4aad3 ("usb:
musb: fix device hotplug behind hub") and no longer applies as far
as I can tell. So let's just remove the earlier code that no longer
is needed.
Fixes: 467d5c9807 ("usb: musb: Implement session bit based runtime PM for musb-core")
Reported-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Declare musb_hdrc_config structures as const as they are only stored in
the config field of a musb_hdrc_platform_data structure. This field is of
type const, so musb_hdrc_config structures having this property can be
made const too.
Done using Coccinelle:
@r disable optional_qualifier@
identifier x;
position p;
@@
static struct musb_hdrc_config x@p={...};
@ok@
struct musb_hdrc_platform_data pdata;
identifier r.x;
position p;
@@
pdata.config=&x@p;
@bad@
position p != {r.p,ok.p};
identifier r.x;
@@
x@p
@depends on !bad disable optional_qualifier@
identifier r.x;
@@
+const
struct musb_hdrc_config x;
File size before:
text data bss dec hex filename
1212 338 0 1550 60e drivers/usb/musb/jz4740.o
File size after:
text data bss dec hex filename
1268 290 0 1558 616 drivers/usb/musb/jz4740.o
File size before:
text data bss dec hex filename
6151 333 16 6500 1964 drivers/usb/musb/sunxi.o
File size after:
text data bss dec hex filename
6215 269 16 6500 1964 drivers/usb/musb/sunxi.o
File size before:
text data bss dec hex filename
3668 864 0 4532 11b4 drivers/usb/musb/ux500.o
File size after:
text data bss dec hex filename
3724 808 0 4532 11b4 drivers/usb/musb/ux500.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MUSB driver now has runtime PM support, but the debugfs driver misses
the PM _get/_put() calls, which could cause MUSB register access
failure.
Cc: stable@vger.kernel.org # 4.9+
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function bfin_fifo_offset is defined but not used:
drivers/usb/musb/blackfin.c:36:12: warning: ‘bfin_fifo_offset’ defined
but not used [-Wunused-function]
static u32 bfin_fifo_offset(u8 epnum)
^~~~~~~~~~~~~~~~
Adding bfin_fifo_offset to bfin_ops fixes this warning and allows musb
core to call this function instead of default_fifo_offset.
Fixes: cc92f6818f ("usb: musb: Populate new IO functions for blackfin")
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function musb_run_resume_work is called only when CONFIG_PM is
enabled. So this function should not be defined when CONFIG_PM is
disabled. Otherwise the compiler issues a warning:
drivers/usb/musb/musb_core.c:2057:12: error: ‘musb_run_resume_work’ defined but
not used [-Werror=unused-function]
static int musb_run_resume_work(struct musb *musb)
^~~~~~~~~~~~~~~~~~~~
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When unloading omap2430, we can get the following splat:
WARNING: CPU: 1 PID: 295 at kernel/irq/manage.c:1478 __free_irq+0xa8/0x2c8
Trying to free already-free IRQ 4
...
[<c01a8b78>] (free_irq) from [<bf0aea84>]
(musbhs_dma_controller_destroy+0x28/0xb0 [musb_hdrc])
[<bf0aea84>] (musbhs_dma_controller_destroy [musb_hdrc]) from
[<bf09f88c>] (musb_remove+0xf0/0x12c [musb_hdrc])
[<bf09f88c>] (musb_remove [musb_hdrc]) from [<c056a384>]
(platform_drv_remove+0x24/0x3c)
...
This is because the irq number in use is 260 nowadays, and the dma
controller is using u8 instead of int.
Fixes: 6995eb68aa ("USB: musb: enable low level DMA operation for Blackfin")
Signed-off-by: Tony Lindgren <tony@atomide.com>
[b-liu@ti.com: added Fixes tag]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During dma teardown for dequque urb, if musb load is high, musb might
generate bogus rx ep interrupt even when the rx fifo is flushed. In such
case any of the follow log messages could happen.
musb_host_rx 1853: BOGUS RX2 ready, csr 0000, count 0
musb_host_rx 1936: RX3 dma busy, csr 2020
As mentioned in the current inline comment, clearing ep interrupt in the
teardown path avoids the bogus interrupt, so implement clear_ep_rxintr()
callback.
This bug seems to be existing since the initial driver for musb support,
but I only validated the fix back to v4.1, so only cc stable for v4.1+.
cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During dma teardown for dequque urb, if musb load is high, musb might
generate bogus rx ep interrupt even when the rx fifo is flushed. In such
case any of the follow log messages could happen.
musb_host_rx 1853: BOGUS RX2 ready, csr 0000, count 0
musb_host_rx 1936: RX3 dma busy, csr 2020
As mentioned in the current inline comment, clearing ep interrupt in the
teardown path avoids the bogus interrupt.
Clearing ep interrupt is platform dependent, so this patch adds a
platform callback to allow glue driver to clear the ep interrupt.
This bug seems to be existing since the initial driver for musb support,
but I only validated the fix back to v4.1, so only cc stable for v4.1+.
cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The DA8xx OTG PHY has some issues when it is forced in host or
peripheral mode. Actually, most of the time, OTG is the best mode
because host or peripheral mode are only required for hardware that
miss some circuitry.
Init the PHY mode OTG mode by default.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first attempt to read a register may fail because the clock may not
be enabled, and then the probe of musb driver will fail.
Call clk_prepare_enable() before the first register read.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds DT support for TI DA8xx/OMAP-L1x/AM17xx/AM18xx MUSB driver
Signed-off-by: Petr Kulhavy <petr@barix.com>
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the function musb_get_mode() to get the DT property "dr_mode"
Signed-off-by: Petr Kulhavy <petr@barix.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: David Lechner <david@lechnology.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no point having this complaint to be dev_err as it is just adding
noise to bootlog.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace pr_err with dev_err to print also device name.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't complain on -EPROBE_DEFER when initializing controller,
the driver probe will be retried later.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sunxi musb has a bug where sometimes it will generate a babble
error on device disconnect instead of a disconnect irq. When this
happens the musb-controller switches from host mode to device mode
(it clears MUSB_DEVCTL_SESSION and sets MUSB_DEVCTL_BDEVICE) and
gets stuck in this state.
Clearing this requires reporting Vbus low for 200 or more ms, but
on some devices Vbus is simply always high (host-only mode, no Vbus
control).
This commit adds a sunxi_musb_recover() callback which makes
sunxi_musb_work call phy_set_mode with the current mode, which
will force end the current session.
This fixes the musb controller getting stuck in this state on systems
without Vbus control; and also fixes the need to unplug the usb-b ->
usb-a cable to get out of this state on systems with Vbus control.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The musb core already handles babble interrupts, so the sunxi glue
having its own custom handling is redundant.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove comments about resume signalling being stopped from
GetPortStatus, something which is no longer the case.
Fixes: 8ed1fb790e ("usb: musb: finish suspend/reset work...")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
-----BEGIN PGP SIGNATURE-----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=5WN9
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.10 merge window
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
This already gets done automatically by PM runtime and we have
a separate autosuspend timeout in musb_core.c.
Reviewed-by: Johan Hovold <johan@kernel.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are missing pm_runtime_disable() in 2430 glue layer. Further,
we only need to enable PM runtime and disable it on exit. With
musb_core.c doing PM, the glue layer as a parent will always be
active when musb_core.c is active.
This fixes host enumeration issues with some devices as reported
by Ladislav Michl <ladis@linux-mips.org>.
And holding an RPM reference while deregistering the child would
lead to a crash in omap2430_runtime_suspend() which dereferences
the now freed child's driver data on put as pointed out by
Johan Hovold <johan@kernel.org>:
Unable to handle kernel paging request at virtual address 6b6b6f17
...
[<c05453d4>] (omap2430_runtime_suspend) from [<c0481410>]
(pm_generic_runtime_suspend+0x3c/0x48)
[<c0481410>] (pm_generic_runtime_suspend) from [<c0121028>]
(_od_runtime_suspend+0x1c/0x30)
[<c0121028>] (_od_runtime_suspend) from [<c04833b0>] (__rpm_callback+0x3c/0x70)
[<c04833b0>] (__rpm_callback) from [<c0483414>] (rpm_callback+0x30/0x90)
[<c0483414>] (rpm_callback) from [<c0483984>] (rpm_suspend+0x118/0x6b4)
[<c0483984>] (rpm_suspend) from [<c04840f4>] (rpm_idle+0x104/0x440)
[<c04840f4>] (rpm_idle) from [<c04844ac>] (__pm_runtime_idle+0x7c/0xb0)
[<c04844ac>] (__pm_runtime_idle) from [<c0545458>] (omap2430_remove+0x38/0x58)
[<c0545458>] (omap2430_remove) from [<c047b2bc>] (platform_drv_remove+0x34/0x4c)
Note that if changes are needed to the autosuspend timeout, it should
be done in musb_core.c.
Reported-by: Ladislav Michl <ladis@linux-mips.org>
Fixes: 87326e8584 ("usb: musb: Remove extra PM runtime calls from
2430 glue layer")
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With a USB hub disconnected, devctl can be 0x19 for about a second
on am335x and will stay forever on at least omap3. And we get no
further interrupts when devctl session bit clears. This keeps
PM runtime active.
Let's fix the issue by polling devctl until the session bit clears
or times out. We can do this by making musb->irq_work into
delayed_work.
And with the polling implemented, we can now also have the quirk
for invalid VBUS it to avoid disconnecting too early while VBUS
is ramping up.
Fixes: 467d5c9807 ("usb: musb: Implement session bit based runtime
PM for musb-core")
Fixes: 65b3f50ed6 ("usb: musb: Add PM runtime support for MUSB DSPS
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 65b3f50ed6 ("usb: musb: Add PM runtime support for MUSB DSPS
glue layer") wrongly added a call for pm_runtime_get_sync to otg_timer
that runs in softirq context. That causes a "BUG: sleeping function called
from invalid context" every time when polling the cable status:
[<c015ebb4>] (__might_sleep) from [<c0413d60>] (__pm_runtime_resume+0x9c/0xa0)
[<c0413d60>] (__pm_runtime_resume) from [<c04d0bc4>] (otg_timer+0x3c/0x254)
[<c04d0bc4>] (otg_timer) from [<c0191180>] (call_timer_fn+0xfc/0x41c)
[<c0191180>] (call_timer_fn) from [<c01915c0>] (expire_timers+0x120/0x210)
[<c01915c0>] (expire_timers) from [<c0191acc>] (run_timer_softirq+0xa4/0xdc)
[<c0191acc>] (run_timer_softirq) from [<c010168c>] (__do_softirq+0x12c/0x594)
I did not notice that as I did not have CONFIG_DEBUG_ATOMIC_SLEEP enabled.
And looks like also musb_gadget_queue() suffers from the same problem.
Let's fix the issue by using a list of delayed work then call it on
resume. Note that we want to do this only when musb core and it's
parent devices are awake, and we need to make sure the DSPS glue
timer is stopped as noted by Johan Hovold <johan@kernel.org>.
Note that we already are re-enabling the timer with mod_timer() in
dsps_musb_enable().
Later on we may be able to remove other delayed work in the musb driver
and just do it from pending_resume_work. But this should be done only
for delayed work that does not have other timing requirements beyond
just being run on resume.
Fixes: 65b3f50ed6 ("usb: musb: Add PM runtime support for MUSB DSPS
glue layer")
Reported-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't use static variable first for checking when musb is
initialized when we have multiple musb instances like on am335x.
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This suppresses printing the error message "failed to get phy" in the
kernel log when the error is -EPROBE_DEFER. This prevents usless noise
in the kernel log.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Cc: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If we're booting pandaboard using NFSroot over built-in g_ether, we
can get the following after booting once and doing a warm reset:
g_ether gadget: ecm_open
g_ether gadget: notify connect true
...
WARNING: CPU: 0 PID: 1 at drivers/bus/omap_l3_noc.c:147
l3_interrupt_handler+0x220/0x34c
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4CFG (Read):
Data Access in User mode du ring Functional access
...
Fix the issue by calling pm_runtime functions from
musb_gadget_queue.
Note that in the long run we should be able to queue the pending
transfers if pm_runtime is not active, and flush the queue from
pm_runtime_resume.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we configure musb with 2430 glue as a peripheral, and then rmmod
omap2430 module, we'll get the following error:
[ INFO: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected ]
...
rmmod/413 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
(&phy->mutex){+.+.+.}, at: [<c04b9fd0>] phy_power_off+0x1c/0xb8
[ 204.678710]
and this task is already holding:
(&(&musb->lock)->rlock){-.-...}, at: [<bf3a482c>]
musb_gadget_stop+0x24/0xec [musb_hdrc]
which would create a new lock dependency:
(&(&musb->lock)->rlock){-.-...} -> (&phy->mutex){+.+.+.}
...
This is because some glue layers expect musb_platform_enable/disable
to be called with spinlock held, and 2430 glue layer has USB PHY on
the I2C bus using a mutex.
We could fix the glue layers to take the spinlock, but we still have
a problem of musb_plaform_enable/disable being called in an unbalanced
manner. So that would still lead into USB PHY enable/disable related
problems for omap2430 glue layer.
While it makes sense to only enable USB PHY when needed from PM point
of view, in this case we just can't do it yet without breaking things.
So let's just revert phy_enable/disable related changes instead and
reconsider this after we have fixed musb_platform_enable/disable to
be balanced.
Fixes: a83e17d0f7 ("usb: musb: Improve PM runtime and phy handling for 2430 glue layer")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We print an error message when platform_device_register_full()
fails, but the initialization of the argument has been removed,
as shown in this warning:
drivers/usb/musb/da8xx.c: In function 'da8xx_probe':
drivers/usb/musb/da8xx.c:521:3: error: 'ret' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This modifies the function to assign the return code before
checking it, and does uses the same method in the check for
usb_phy_generic_register() as well.
Fixes: 947c49afe4 ("usb: musb: da8xx: Remove mach code")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the session bit based PM runtime working on musb, we've
implemented few quirks to attempt to detect the current state of
the hardware. One of the quirks is for invalid VBUS as peripheral,
but it is not working in all cases.
If we start musb on dm3730 as a peripheral with no cable connected,
we will get the devctl 91 state once and will never idle as there
are not further interrupts from musb. So we need to ignore the first
devctl 91 state as there will be more interrupts if we're connected.
The invalid VBUS state also can happen always when connected to
certain USB hubs. Looks like musb on dm3730 can claim invalid VBUS
with some hubs while 3717-evm and BeagleBone don't. This causes
session as peripheral to fail for dm3730 with some hubs.
This too is fixed by ignoring only the first invalid VBUS. When
connected, we can just look at the session bit as that will clear
automatically when the session ends.
Fixes: 467d5c9807 ("usb: musb: Implement session bit based runtime PM for musb-core")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we unconfigure musb as a USB peripheral with cable connected,
and then remove the cable, no interrupts will happen. And musb
thinks we're still connected keeping the device active.
Now with the session bit based PM runtime working for musb, we
can fix this issue by calling musb irq_work. That rechecks the
devctl register and reconfigures PM runtime based on the devctl.
Fixes: 467d5c9807 ("usb: musb: Implement session bit based runtime PM for musb-core")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Export musb_root_disconnect for use in modules, so that musb glue
code build as module can use it.
This fixes the buildbot errors for -next in arm64-allmodconfig
and arm-allmodconfig.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 7cba17ec9a ("musb: sunxi: Add support for platform_set_mode")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have CONFIG_BLACKFIN ifdef redefining all musb registers in
musb_regs.h and tusb6010.h is never included causing a build
error with blackfin-allmodconfig and COMPILE_TEST.
Let's fix the issue by not building tusb6010 if CONFIG_BLACKFIN
is selected.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
aDate is always the empty string, so entirely pointless. The aRevision
formatting might as well be done as part of the pr_debug() call - that
also avoids it altogether if pr_debug is compiled out.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to return a negative error code from the usb_phy_generic_register()
error handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new phy-da8xx-usb driver to take the place of the mach code that
pokes CFGCHIP2 in the da8xx musb glue driver. This unbreaks the driver.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify things a bit by using devm functions where possible.
Signed-off-by: David Lechner <david@lechnology.com>
[b-liu@ti.com: fixed merge conflict]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows run-time dr_mode switching support via the "mode" musb
sysfs attribute.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can now just use PM runtime autoidle support as musb core
keeps things enabled when the devctl session bit is set. And
there's no need for dsps_musb_try_idle() so let's just remove
it.
Note that as cppi41 dma is clocked by musb, this only makes
PM work for dsps glue layer if CONFIG_MUSB_PIO_ONLY=y and
cppi41.ko is unloaded. This will get fixed when cppi41.c has
PM runtime implemented.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With musb core now blocking PM based on the devctl status
bit, we can remove related quirks from the 2430 glue layer
and simplify PM runtime further.
Lets's also use musb->controller instead of dev to make it
clear we make the PM runtime calls for the core, not the
glue layer.
And we can now also lower the autoidle timeout.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to be polling the state when nothing is connected.
Let's change the polling logic in preparation for PM runtime
support.
Signed-off-by: Tony Lindgren <tony@atomide.com>
[b-liu@ti.com: undo unnecessary line leading whitespace change]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to keep musb enabled always when the session bit is
set. This simplifies the PM runtime and allows making it more
generic across the various glue layers.
So far the only exception to just following the session bit is
host mode disconnect where the session bit stays set.
In that case, just allow PM and let the PM runtime autoidle
timeout deal with it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
[b-liu@ti.com: changed using dev_dbg() to musb_dbg()]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we have USB gadgets disabled and USB_MUSB_HOST set, we get
errors "possible irq lock inverssion dependency detected"
errors during boot.
Let's fix the issue by adding start_musb flag and start
the controller after we're out of the spinlock protected
section.
Reported-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
phy-sun4i-usb now has proper dr_mode handling, it always registers an
extcon, and sends a notify with the mode (even when in peripheral- /
host-only mode) at least once.
So we can simply the sunxi musb glue by always registering its extcon
notifier and relying on sunxi_musb_work() to enable vbus when in
host-only mode.
This also enables host- and peripheral-only mode with vbus monitoring.
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sunxi_musb_dma_controller_create and _destroy are not exported
or used outside the driver, so fix sparse warnings by making these
two static:
drivers/usb/musb/sunxi.c:357:23: warning: symbol 'sunxi_musb_dma_controller_create' was not declared. Should it be static?
drivers/usb/musb/sunxi.c:363:6: warning: symbol 'sunxi_musb_dma_controller_destroy' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move struct cppi41_dma_channel to the header file so other modules can
use it.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
davinci.h is not required by cppi_dma.h but cppi_dma.c, so move the
include to the right place.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds tracepoints to dump musb interrupt events.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds tracepoints to musb register read/write wrappers to get
trace log for register access.
The default tacepoint log prefix here would be musb_readX/writeX(),
which is not much helpful. So this patch let the tracepoints use
__buildin_return_address(0) to print the caller funciton name to
provide more context of the register access.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb core already exports the register read/write wrappers, so clean up
the duplication in dsps glue.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To avoid printk() overhead while debugging, this patch implements the
foundation of tracepoints logging for musb driver to make debug
easier.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comment is wrong, glue is devm_kzalloc-ed mem attached to the
"allwinner,sun4i-a10-musb" compatible platform-dev. Where as
glue->musb_pdev is a newly created "musb-hdrc" platform-dev.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop using the return value of platform_device_register_full() to get to
the struct musb in sunxi_musb_work(). If a gadget has been registered
(insmod-ed) before the musb driver, then musb_start will get called
from the musb_core probe function and sunxi_musb_work() may run before
platform_device_register_full() has returned.
Instead store a pointer to struct musb in struct sunxi_glue when
sunxi_musb_enable gets called. Note that sunxi_musb_enable always gets
called before sunxi_musb_work() can run.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that the endpoint is stopped by clearing REQPKT before
clearing DATAERR_NAKTIMEOUT before rotating the queue on the
dedicated bulk endpoint.
This addresses an issue where a race could result in the endpoint
receiving data before it was reprogrammed resulting in a warning
about such data from musb_rx_reinit before it was thrown away.
The data thrown away was a valid packet that had been correctly
ACKed which meant the host and device got out of sync.
Signed-off-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
shared_fifo endpoints would only get a previous tx state cleared
out, the rx state was only cleared for non shared_fifo endpoints
Change this so that the rx state is cleared for all endpoints.
This addresses an issue that resulted in rx packets being dropped
silently.
Signed-off-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Incorrect cppi dma channel is referenced in musb_rx_dma_iso_cppi41(),
which causes kernel NULL pointer reference oops later when calling
cppi41_dma_channel_program().
Fixes: 069a3fd (usb: musb: Remove ifdefs for musb_host_rx in musb_host.c
part1)
Cc: <stable@vger.kernel.org> # v4.2+
Reported-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the session bit was not set in the backup of devctl register,
restoring devctl would clear the session bit. Therefor, only restore
devctl register when the session bit was set in the backup.
This solves the device enumeration failure in otg mode exposed by commit
56f487c (PM / Runtime: Update last_busy in rpm_resume).
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no longer any need for custom initcall level for
musb.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the pull up being handled with delayed work, we can
now finally remove pm_runtime_set_irq_safe that blocks the
MUSB glue from idling.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With PM runtime behaving, these are all now unnecessary.
Doing pm_runtime_get(musb->controller) will keep the parent
glue layer also active.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least on n900 we have phy-twl4030-usb only generating cable
interrupts, and then have a separate USB PHY.
In order for musb to know the real cable status, we need to
clear any cached state until musb is ready. Otherwise the cable
status interrupts will get just ignored if the status does
not change from the initial state.
To do this, let's add a return value to musb_mailbox(), and
reset cached linkstat to MUSB_UNKNOWN on error. Sorry to cause
a bit of churn here, I should have added that already last time
patching musb_mailbox().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least 2430 glue layer pulls d+ high on start up even if there are
no gadgets configured. This is bad at least for anything using a separate
battery charger chip as it can confuse the charger detection.
Let's fix the issue by removing the bogus glue layer code tinkering
with the SESSION bit. As pointed out Bin Liu <b-liu@ti.com> and
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>, the SESSION
bit just starts host mode if ID pin is grounded, and starts the
srp is ID pin is floating. So without the ID pin changing, it's
unable to force musb mode to anything. And just for starting a
host mode, things work fine without this code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is no longer needed with PM runtime at least for 2430 glue.
We can now rely only on PM runtime and cable detection.
The other glue layers can probably remove try_idle too, but that
needs to be tested for each platform before doing it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This simplifies things and allows idling both MUSB and PHY
when nothing is configured. Let's just return early from PM
runtime if musb is not yet initialized.
Let's also warn if PHY is not configured.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We may have drivers loaded but no configured gadgets and MUSB may be in
host mode. If gadgets are configured during host mode, PM runtime will
get confused.
Disable PM runtime from gadget state, and do it based on the cable
and last state.
Note that we may get multiple cable events, so we need to keep track
of the power state.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have MUSB setting pm_runtime_irq_safe with the following
commits:
30a70b026b ("usb: musb: fix obex in g_nokia.ko causing kernel panic")
3e43a07256 ("usb: musb: core: add pm_runtime_irq_safe()")
Let's fix things to use delayed work so we can remove the
pm_runtime_irq_safe.
Note that we may want to set this up in a generic way in the
gadget framework eventually.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The conditional use of PM runtime does not work properly
for musb gadget. On cable disconnect we may not get any
USB_EVENT_NONE leaving the PM runtime call unpaired.
Let's fix the issue by making sure the PM runtime calls are
paired within the functions. The glue layer will take care
of the rest.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's not tinker with the PM runtime of musb core from the omap2430
wrapper. This allows us to initialize PM runtime for musb core later
on instead of doing it in stages. And omap2430 wrapper has no need
to for accessing musb core at this point.
Note that this does not remove all the PM runtime calls from the
glue layer, those will get removed in a later patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's make the PM runtime use the standard autosuspend calls.
Commit 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind") means we must pair use_autosuspend with
dont_use_autosuspend and then use put_sync to properly idle the
device.
Note that we'll be removing the PM runtime calls from the glue
layer to the MUSB core in the next patch. And we can also remove
the pointless FIXME comment now.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have remove() already calling shutdown(), so let's drop it
and move the code to remove(). No code changes, we'll drop the
the FIXME in the following patch with more clean-up.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looks like at least 2430 glue won't idle reliably with the 200 ms
autosuspend delay. This causes deeper idle states being blocked for
the whole SoC when disconnecting OTG A cable.
Increasing the delay to 500 ms seems to idle both MUSB and the PHY
reliably. This is probably because of time needed by the hardware
based negotiation between MUSB and the PHY.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the board is powering attached usb devices via the otg port
sometimes / on some devices it takes slightly too long for the Vbus
detection code in phy-sun4i-usb.c to signal that Vbus is high after
enabling Vbus and the musb hardware signals a MUSB_INTR_VBUSERROR
interrupt.
This commit sets the otg state to A_WAIT_VRISE upon enabling Vbus
making musb_stage0_irq() ignore the first VBUSERR_RETRY_COUNT
VBUSERROR interrupts, fixing connection issues in these cases.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the mode handling to the platform_set_mode callback.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the DMA engine check was moved to musb_tx_dma_porgram(), both
musb_tx_dma_set_mode_cppi_tusb() and musb_tx_dma_set_mode_mentor() always
return 0, so we can make both these functions *void*.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 754fe4a92c ("usb: musb: Remove ifdefs for TX DMA for musb_host.c")
looks incomplete: the DMA engine checks are done outside the Mentor/UX500
handler but inside the CPPI/TUSB handler. Move the checks out of the CPPI/
TUSB handler into its caller, musb_tx_dma_program().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
urb->status is set when endpoint csr RXSTALL, H_ERROR, DATAERROR or
INCOMPRX bit is set. Those bits mean a broken pipe, so don't start next
urb when any of these bits is set by checking urb->status.
To minimize the risk of regression, only do so for RX, until we have a
test case to understand the behavior of TX.
The patch fixes system freeze issue caused by repeatedly invoking RX ISR
while removing a usb uart device connected to a hub, in which case the
hub has no chance to report the disconnect event due to the kernel is
busy in processing the RX interrupt flooding.
Fix checkpatch complaint (qh != NULL) as while.
Reported-by: Max Uvarov <muvarov@gmail.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MUSB Programming Guide states that the driver should clear RXCSR
bit2 when the controller sets the bit.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_get_phy() function returns either a valid pointer to phy or
ERR_PTR() error, check for NULL always fails and may lead to oops on
error path, fix this issue.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2035772010.
Commit 20357720 claims throughput improvement for MSC/UVC, but I
don't see much improvement. Following are the MSC measurement using
dd on AM335x GP EVM.
with BCD_BH: read: 14.9MB/s, write: 20.9MB/s
without BCD_BH: read: 15.2MB/s, write: 21.2MB/s
However with this commit the following regressions have been observed.
1. ASIX usb-ethernet dongle is completely broken on UDP RX.
2. Unpluging a 3G modem, which uses option driver, behind a hub causes
console log flooding with the following message.
option_instat_callback: error -71
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some functions, such as f_sourcesink, rely on an endpoint's desc
field during their requests' complete() callback, so clear it only
_after_ nuking all requests to avoid NULL pointer dereference.
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The musb_hdrc_platform_data::config was defined as a non-const pointer.
However some drivers (e.g. the ux500) set up this pointer to point to a
static structure, which is potentially dangerous. Since the musb core
uses the pointer in a read-only manner the const qualifier was added to
protect the content of the config.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
MODULE_DEVICE_TABLE() is missing, so the module isn't auto-loading on
sunxi systems using the OTG controller. This commit adds the missing
line so it loads automatically when building it as a module and running
on a system with an USB OTG port.
Signed-off-by: Emilio López <emilio.lopez@collabora.co.uk>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When dma_addr_t is 64-bit, we get a warning about an invalid cast
in the call to ux500_dma_is_compatible() from ux500_dma_channel_program():
drivers/usb/musb/ux500_dma.c: In function 'ux500_dma_channel_program':
drivers/usb/musb/ux500_dma.c:210:51: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
if (!ux500_dma_is_compatible(channel, packet_sz, (void *)dma_addr, len))
The problem is that ux500_dma_is_compatible() is called from the
main musb driver on the virtual address, but here we pass in a
DMA address, so the types are fundamentally different but it works
because the function only checks the alignment of the buffer and
that is the same.
We could work around this by adding another cast, but I have checked
that the buffer we get passed here is already checked before it
gets mapped, so the second check seems completely unnecessary
and removing it must be the cleanest solution.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The musb driver prints DMA addresses in a few places, using the
0x%x format string. This is wrong on 64-bit architectures (which
need %lx) and 32-bit ARM with CONFIG_LPAE set (which needs
%llx), otherwise we print the wrong data, as gcc warns:
musb/musbhsdma.c: In function 'configure_channel':
musb/musbhsdma.c:120:53: error: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t {aka long long unsigned int}' [-Werror=format=]
dev_dbg(musb->controller, "%p, pkt_sz %d, addr 0x%x, len %d, mode %d\n",
musb/musbhsdma.c: In function 'dma_channel_program':
musb/musbhsdma.c:155:53: error: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t {aka long long unsigned int}' [-Werror=format=]
dev_dbg(musb->controller, "ep%d-%s pkt_sz %d, dma_addr 0x%x length %d, mode %d\n",
musb/tusb6010_omap.c: In function 'tusb_omap_dma_program':
musb/tusb6010_omap.c:313:53: error: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t {aka long long unsigned int}' [-Werror=format=]
dev_dbg(musb->controller, "ep%i %s dma ch%i dma: %08x len: %u(%u) packet_sz: %i(%i)\n",
This uses the %pad format string, which prints a dma_addr_t that
gets passed by reference, which works for all combinations.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Commit ac33cdb166 ("usb: musb: Remove ifdefs for musb_host_rx in
musb_host.c part5") introduces a problem setting DMA host mode.
The musb_advance_schedule() is called immediately after receiving an
endpoint RX interrupt without waiting for the DMA transfer to complete.
As a consequence when the dma complete interrupt arrives the in_qh
member of hw_ep is already null an the musb_host_rx() exits on !urb
error case. Fix the done condition that advances the musb schedule.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Commit 754fe4a92c ("usb: musb: Remove ifdefs for TX DMA for musb_host.c")
introduces a problem setting the desired channel mode for the Mentor DMA
engine.
There is a case where an address is incorrectly assigned to the DMA
channel desired mode when it should instead be assigned the actual mode
value. This results in the value of channel->desired_mode not being
correct.
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
CC drivers/usb/musb/tusb6010.o
drivers/usb/musb/tusb6010.c: In function ‘tusb_musb_init’:
drivers/usb/musb/tusb6010.c:1133:2: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration]
sync = ioremap(mem->start, resource_size(mem));
^
drivers/usb/musb/tusb6010.c:1133:7: warning: assignment makes pointer from integer without a cast [enabled by default]
sync = ioremap(mem->start, resource_size(mem));
^
drivers/usb/musb/tusb6010.c:1162:4: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(sync);
^
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 7d32cdef53 ("usb: musb: fail with error when no DMA
controller set"), caused the core platform driver to correctly return an
error code when fail probing.
Unfurtante it also caused bug for a NULL pointer dereference, during
system suspend for the ux500 driver. The reason is a lacking validation
of the corresponding ->driver_data pointer, which won't be set when the
musb core driver fails to probe (or haven't yet been probed).
Fixes: 7d32cdef53 ("usb: musb: fail with error when no DMA...")
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The phy's init routine must be called before it can be used. Do so in
musb_init_controller and the matching shutdown in musb_remove.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When reloading omap2430 kernel module we get a warning about
unbalanced pm_runtime_enable. Let's fix this. Note that we
need to do this after the child musb-core platform_device is
removed because of pm_runtime_irq_safe being set at the child.
Cc: Bin Liu <b-liu@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: NeilBrown <neil@brown.name>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We currently can't unload omap2430 MUSB platform glue driver module and
this cause issues for fixing the MUSB code further. The reason we can't
remove omap2430 is because it uses the PHY functions and also exports the
omap_musb_mailbox function that some PHY drivers are using.
Let's fix the issue by exporting a more generic musb_mailbox function
from the MUSB core and allow platform glue layers to register phy_callback
function as needed.
And now we can now also get rid of the include/linux/musb-omap.h.
Cc: Bin Liu <b-liu@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: NeilBrown <neil@brown.name>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes redundant condition.
(!A || (A && B)) is the same as (!A || B).
Fixes indentation too.
Tested by: compilation only
Caught by: cppcheck
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This file already uses pr_debug in a few places; this converts the
remaining printks.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If musb_init_controller fails at musb_platform_init, we have already
called pm_runtime_irq_safe for musb and that causes the pm runtime count
to be enabled for parent before the parent has completed initialization.
This causes pm to stop working as on unload nothing gets idled.
This issue can be reproduced at least with:
# modprobe omap2430
HS USB OTG: no transceiver configured
musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517
# modprobe phy-twl4030-usb
# rmmod omap2430
And after the steps above omap2430 will block deeper idle states on
omap3.
To fix this, let's not enable pm runtime until we need to and the
parent has been initialized. Note that this does not fix the issue of
PM being broken for musb during runtime.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The CPPI-4.1 driver selects TI_CPPI41, which is a dmaengine
driver and that may not be available when CONFIG_DMADEVICES
is not set:
warning: (USB_TI_CPPI41_DMA) selects TI_CPPI41 which has unmet direct dependencies (DMADEVICES && ARCH_OMAP)
This adds an extra dependency to avoid generating warnings in randconfig
builds. Ideally we'd remove the 'select' statement, but that has the
potential to break defconfig files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 411dd19c68 ("usb: musb: Kconfig: Select the DMA driver if DMA mode of MUSB is enabled")
Signed-off-by: Felipe Balbi <balbi@ti.com>
Change the permission of usb_dma parameter so it can
be used for runtime debug without reboot.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here are a few changes in musb_h_tx_flush_fifo().
- It has been observed that sometimes (if not always) musb is unable
to flush tx fifo during urb dequeue when disconnect a device. But
it seems to be harmless, since the tx fifo flush is done again in
musb_ep_program() when re-use the hw_ep.
But the WARN() floods the console in the case when multiple tx urbs
are queued, so change it to dev_WARN_ONCE().
- applications could queue up many tx urbs, then the 1ms delay could
causes minutes of delay in device disconnect. So remove it to get
better user experience. The 1ms delay does not help the flushing
anyway.
- cleanup the debug code - related to lastcsr.
----
Note: The tx fifo flush issue has been observed during device disconnect
on AM335x.
To reproduce the issue, ensure tx urb(s) are queued when unplug the usb
device which is connected to AM335x usb host port.
I found using a usb-ethernet device and running iperf (client on AM335x)
has very high chance to trigger the problem.
Better to turn on dev_dbg() in musb_cleanup_urb() with CPPI enabled to
see the issue when aborting the tx channel.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a bit of a mess in the order of arguments to the ulpi write
callback. There is
int ulpi_write(struct ulpi *ulpi, u8 addr, u8 val)
in drivers/usb/common/ulpi.c;
struct usb_phy_io_ops {
...
int (*write)(struct usb_phy *x, u32 val, u32 reg);
}
in include/linux/usb/phy.h.
The callback registered by the musb driver has to comply to the latter,
but up to now had "offset" first which effectively made the function
broken for correct users. So flip the order and while at it also
switch to the parameter names of struct usb_phy_io_ops's write.
Fixes: ffb865b1e4 ("usb: musb: add ulpi access operations")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here is the big USB patchset for 4.4-rc1.
As usual, most of the changes are in the gadget subsystem, and we
removed a host controller for a device that is no longer in existance,
and probably never was even made public. There is also other minor
driver updates and new device ids, full details in the changelog.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6gVMACgkQMUfUDdst+ynLZgCePfhiDuwriaX7osq90HDu8JOc
pTEAn2dBdw2VMPToUlxccR963YSfgu2A
=mMgp
-----END PGP SIGNATURE-----
Merge tag 'usb-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB patchset for 4.4-rc1.
As usual, most of the changes are in the gadget subsystem, and we
removed a host controller for a device that is no longer in existance,
and probably never was even made public. There is also other minor
driver updates and new device ids, full details in the changelog.
All of these have been in linux-next for a while"
* tag 'usb-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (233 commits)
USB: core: Codestyle fix in urb.c
usb: misc: usb3503: Use i2c_add_driver helper macro
usb: host: lpc32xx: don't unregister phy device
usb: host: lpc32xx: balance clk enable/disable on removal
usb: host: lpc32xx: fix warnings caused by enabling unprepared clock
uwb: drp: Use setup_timer
uwb: neh: Use setup_timer
uwb: rsv: Use setup_timer
USB: qcserial: add Sierra Wireless MC74xx/EM74xx
usb: chipidea: otg: don't wait vbus drops below BSV when starts host
chipidea: ci_hdrc_pci: use PCI_VDEVICE() instead of PCI_DEVICE()
doc: dt-binding: ci-hdrc-usb2: split vendor specific properties
usb: chipidea: imx: add imx6ul usb support
doc: dt-binding: ci-hdrc-usb2: improve property description
usb: chipidea: imx: add usb support for imx7d
Doc: usb: ci-hdrc-usb2: Add phy-clkgate-delay-us entry
usb: chipidea: Add support for 'phy-clkgate-delay-us' property
usb: chipidea: Use extcon framework for VBUS and ID detect
usb: gadget: net2280: restore ep_cfg after defect7374 workaround
usb: dwc2: host: Fix use after free w/ simultaneous irqs
...
Commit ddef08dd00 ("Driver core: wakeup the parent device before trying
probe") started automatically ensuring the parent device is enabled when
the child gets probed.
This however caused a regression for MUSB omap2430 interface as the
runtime PM for the parent device needs the child initialized to access
the MUSB hardware registers.
Let's delay the enabling of PM runtime for the parent until the child
has been properly initialized as suggested in an earlier patch by
Grygorii Strashko <grygorii.strashko@ti.com>.
In addition to delaying pm_runtime_enable, we now also need to make sure
the parent is enabled during omap2430_musb_init. We also want to propagate
an error from omap2430_runtime_resume if struct musb is not initialized.
Note that we use pm_runtime_put_noidle here for both the child and parent
to prevent an extra runtime_suspend/resume cycle.
Let's also add some comments to avoid confusion between the
two different devices.
Fixes: ddef08dd00 ("Driver core: wakeup the parent device before
trying probe")
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix musb_platform_get_vbus_status return value in case of platform
implementation is not defined, bringing expected behaviour of
musb_platform_get wrapper. Add musb_vbus_show default method to determine
VBUS status in case platform method is not defined.
Signed-off-by: Roman Alyautdin <ralyautdin@dev.rtsoft.ru>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now that it is possible to build in multiple dma engines, we can no longer
require MUSB_PIO_ONLY to be set when using the sunxi musb glue.
This patch adds dummy dma hooks to make the musb glue work without
MUSB_PIO_ONLY. This hooks are fake because we do not support dma with
musb on sunxi. The Allwinnner Android kernels have some dma code, but it
is disabled as Allwinner never managed to get it to work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Set musb config->maximum_speed based on the dts setting to control musb
speed.
By default musb works in high-speed mode. Adding
maximum-speed = "full-speed";
to dts usb node will force musb to full-speed mode.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Set the Power register HSENAB bit based on musb->config->maximum_speed,
so that the glue layer can control MUSB to work in high- or full-speed.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After a few iterations of start/stop UVC camera streaming, the streaming
stops.
This patch adds 250us delay in the cppi channel abort path to let cppi
drain properly.
Using 50us delay seems to be too aggressive, some webcams are still
broken. 250us is the original value used in TI 3.2 kernel.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the regression caused by commit ad78c91860 ("usb: musb: dsps: just
start polling already") which causes polling the ID pin status even in
device-only mode.
Fixes: ad78c91860 ("usb: musb: dsps: just start polling already")
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In certain situations, an interrupt triggers on resume, before musb_start()
has been called. This has been observed to cause enumeration issues after
suspend/resume cycles with AM335x.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The change ensures otg is not in a A- state when checking for VBUS in
peripheral mode.
musb_start() where VBUS checking is in can be called in many situations.
One example is in babble recovery routine, in which otg is transitioning
from A-HOST to A-WAIT-BCON, but VBUS discharge takes time, so
musb->is_active could be set to 1 due to this improper checking, then it
causes musb_bus_suspend() failed which leads to warning log message
flooding.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add missing break after 'default' label to fix compilation error.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
since commit 33c300cb90 ("usb: musb: dsps:
don't fake of_node to musb core") we have been
preventing CPPI 4.1 from probing due to NULL
of_node. We can't revert said commit otherwise
a different regression would show up, so the fix
is to look for the parent device's (glue layer's)
of_node instead, since that's the thing which
is actually described in DTS.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit fb91cddc54 ("usb: musb: Remove DMA
ifdef for musb_gadget.c short_packet") tried
to remove DMA ifdeferry from musb_gadget.c
but ended up leaving some around.
Remove them so that when building kernels with
all DMA engines enabled, we don't end up trying
to allocte channels twice.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add 'match_ep' callback to utilize chip-specific knowledge in endpoint matching
process. Function does the same that was done by chip-specific code inside
of epautoconf. Now this code can be removed from there to separate generic code
from platform specific logic.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace redundant variable use in return statement.
Signed-off-by: Saurabh Karajgaonkar <skarajga@visteon.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
With recent changes to MUSB code, we can now now get rid of
the Kconfig choise for the DMA code and allow building in any
of the desired DMA code. This makes life easier for distros.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Due to some UDC controllers may not support zlp, usb gadget layer
needs to provide a generic way to inform gadget functions about non-standard
hardware limitations.
This patch adds 'quirk_zlp_not_supp' field to struct usb_gadget and helper
function gadget_is_zlp_supported(). It also sets 'quirk_zlp_not_supp'
to 1 in musb UDC driver, which has such limitation.
[ balbi@ti.com : make it build ]
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The A33 SoC uses the same musb controller as found on the A31 and later,
but allwinner has removed the configdata register, this commit adds special
handling for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The A31 SoC uses the same musb controller as found in earlier SoCs, but it
is hooked up slightly different. Its SRAM is private and no longer controlled
through the SRAM controller, and its reset is controlled via a separate
reset controller. This commit adds support for this setup.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is based on initial code to get the Allwinner sunxi musb controller
supported by Chen-Yu Tsai and Roman Byshko.
This adds support for the Allwinner sunxi musb controller in both host only
and otg mode. Peripheral only mode is not supported, as no boards use that.
This has been tested on a cubietruck (A20 SoC) and an UTOO P66 tablet
(A13 SoC) with a variety of devices in host mode and with the g_serial gadget
driver in peripheral mode, plugging otg / host cables in/out a lot of times
in all possible imaginable plug orders.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently, we're calling musb_start() twice for DRD ports
in some situations. This has been observed to cause enumeration
issues after suspend/resume cycles with AM335x.
In order to fix the problem, we just have to fix the check
on musb_has_gadget() so that it only returns true if
current mode is Host and ignore the fact that we have or
not a gadget driver loaded.
Fixes: ae44df2e21 (usb: musb: call musb_start() only once in OTG mode)
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: <stable@vger.kernel.org> # v3.11+
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pali Rohár