The kerneldoc for irq_set_irq_wake() says:
Enable/disable power management wakeup mode, which is
disabled by default.
regmap_irq_set_wake() clears bits to enable wake for an interrupt,
and sets bits to disable wake. Hence, we should set all bits in
wake_buf initially, to mirror the expected disabled state.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If a regmap-irq chip has no wake base:
* There's no point calling .irq_set_wake, hence IRQCHIP_SKIP_SET_WAKE.
* If some IRQs in the chip are enabled for wake and some aren't, we
should mask those interrupts that are not wake enabled, so that if
they occur during suspend, the system is not awoken. Hence,
IRQCHIP_MASK_ON_SUSPEND.
Note that IRQCHIP_MASK_ON_SUSPEND is handled by check_wakeup_irqs(),
which always iterates over every single interrupt in the system,
irrespective of whether an interrupt is a child of a controller whose
output interrupt has no wake-enabled inputs and hence is presumably
masked itself. Hence this change might cause interrupt unnecessary
masking operations and associated register I/O.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is intended to give each irq_chip a useful name, rather than hard-
coding them all as "regmap".
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will allow later patches to adjust portions of the irq_chip
individually for each regmap_irq_chip that is created.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Don't write the full register, it's possible there's bits other than the
masks in the same register which we shouldn't be changing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
A number of places in the code were printing error messages that included
the address of a register, but were not calculating the register address
in the same way as the access to the register. Use a temporary to solve
this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow chips to provide a bank of registers for controlling the wake state
in a similar fashion to the masks and propagate the wake count to the
parent interrupt controller.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the driver supplied an empty entry in the array of IRQs then return
an error rather than trying to do the mapping. This is intended for use
with handling chip variants and similar situations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In some chips the IRQ status registers are not contiguous in the register
map but spaced at even spaces. This is an easy case to handle with minor
changes. It is assume for this purpose that the stride for status is
equal to the stride for mask/ack registers as well.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This gets us up to date with the recommended current kernel infrastructure
and should transparently give us device tree interrupt bindings for any
devices using the framework. If an explicit IRQ mapping is passed in then
a legacy interrupt range is created, otherwise a simple linear mapping is
used. Previously a mapping was mandatory so existing drivers should not
be affected.
A function regmap_irq_get_virq() is provided to allow drivers to map
individual IRQs which should be used in preference to the existing
regmap_irq_chip_get_base() which is only valid if a legacy IRQ range is
provided.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit f01ee60fff ("regmap: implement register striding") caused the
compile errors below. Fix them.
drivers/base/regmap/regmap-irq.c: In function 'regmap_irq_sync_unlock':
drivers/base/regmap/regmap-irq.c:62:12: error: 'map' undeclared (first use in this function)
drivers/base/regmap/regmap-irq.c:62:12: note: each undeclared identifier is reported only once for each function it appears in
drivers/base/regmap/regmap-irq.c: In function 'regmap_irq_enable':
drivers/base/regmap/regmap-irq.c:77:37: error: 'map' undeclared (first use in this function)
drivers/base/regmap/regmap-irq.c: In function 'regmap_irq_disable':
drivers/base/regmap/regmap-irq.c:85:37: error: 'map' undeclared (first use in this function)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regmap_config.reg_stride is introduced. All extant register addresses
are a multiple of this value. Users of serial-oriented regmap busses will
typically set this to 1. Users of the MMIO regmap bus will typically set
this based on the value size of their registers, in bytes, so 4 for a
32-bit register.
Throughout the regmap code, actual register addresses are used. Wherever
the register address is used to index some array of values, the address
is divided by the stride to determine the index, or vice-versa. Error-
checking is added to all entry-points for register address data to ensure
that register addresses actually satisfy the specified stride. The MMIO
bus ensures that the specified stride is large enough for the register
size.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For files that are actively using linux/device.h, make sure
that they call it out. This will allow us to clean up some
of the implicit uses of linux/device.h within include/*
without introducing build regressions.
Yes, this was created by "cheating" -- i.e. the headers were
cleaned up, and then the fallout was found and fixed, and then
the two commits were reordered. This ensures we don't introduce
build regressions into the git history.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allows devices to discover their own interrupt without having to remember
it themselves.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While the IRQ core doesn't currently support shared threaded interrupts
that's no reason for drivers not to do their bit and report IRQ_NONE when
they don't get an interrupt. This allows the core spurious/wedget interrupt
detection support to do its thing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There seem to be lots of regmap-using devices with very similar interrupt
controllers with a small bank of interrupt registers and mask registers
with an interrupt per bit. This won't cover everything but it's a good
start.
Each chip supplies a base for the status registers, a base for the mask
registers, an optional base for writing acknowledgements (which may be the
same as the status registers) and an array of bits within each of these
register banks which indicate the interrupt.
There is an assumption that the bit for each interrupt will be the same
in each of the register bank.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren