o min_tx_rate puts lower limit on the VF bandwidth. VF is guaranteed
to have a bandwidth of at least this value.
max_tx_rate puts cap on the VF bandwidth. VF can have a bandwidth
of up to this value.
o A new handler set_vf_rate for attr IFLA_VF_RATE has been introduced
which takes 4 arguments:
netdev, VF number, min_tx_rate, max_tx_rate
o ndo_set_vf_rate replaces ndo_set_vf_tx_rate handler.
o Drivers that currently implement ndo_set_vf_tx_rate should now call
ndo_set_vf_rate instead and reject attempt to set a minimum bandwidth
greater than 0 for IFLA_VF_TX_RATE when IFLA_VF_RATE is not yet
implemented by driver.
o If user enters only one of either min_tx_rate or max_tx_rate, then,
userland should read back the other value from driver and set both
for IFLA_VF_RATE.
Drivers that have not yet implemented IFLA_VF_RATE should always
return min_tx_rate as 0 when read from ip tool.
o If both IFLA_VF_TX_RATE and IFLA_VF_RATE options are specified, then
IFLA_VF_RATE should override.
o Idea is to have consistent display of rate values to user.
o Usage example: -
./ip link set p4p1 vf 0 rate 900
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 900 (Mbps), max_tx_rate 900Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
./ip link set p4p1 vf 0 max_tx_rate 300 min_tx_rate 200
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 300 (Mbps), max_tx_rate 300Mbps,
min_tx_rate 200Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
./ip link set p4p1 vf 0 max_tx_rate 600 rate 300
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5, tx rate 600 (Mbps), max_tx_rate 600Mbps,
min_tx_rate 200Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Faster than memcpy/memset on some architectures.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the dates for files that have been added to in 2012-2013.
Drop the 'Solarstorm' brand name that's still lingering here.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Add efx_nic_type operations for the many efx_nic functions that need
to be implemented different on EF10. For now, change most of the
existing efx_nic_*() functions into inline wrappers. As a later step,
we may be able to improve branch prediction for operations used on the
fast path by copying the pointers into each queue/channel structure.
Move the Falcon/Siena implementations to new file farch.c and rename
the functions and static data to use a prefix of 'efx_farch_'.
Move efx_may_push_tx_desc() to nic.h, as the EF10 TX code will also
use it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The EF10 architecture has a very different register layout from
previous controllers, so we'll use separate files for the two sets of
register definitions. Use 'farch' as an abbreviation for
Falcon-architecture.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Most call sites for efx_nic_alloc_buffer() are part of the probe or
reconfiguration paths and can allocate with GFP_KERNEL. A few others
should use GFP_NOIO (I think). Only one is in atomic context and
must use the current GFP_ATOMIC.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
A few functions are using heap buffers; change them to use stack
buffers as we really don't need to resort to the heap for a 252
byte buffer in process context.
MC_CMD_MEMCPY is quite weird in that it can use inline data placed in
the request buffer after the array of records. Thus there are two
variable-length arrays and we can't use the normal accessors for
the second. So we have to use _MCDI_PTR() in efx_sriov_memcpy().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
MCDI_DECLARE_BUF declares a variable as an MCDI buffer of the
requested length, adding any necessary padding.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
efx_writed_table() uses a step of 16 bytes but efx_readd_table() uses
a step of 4 bytes. Why are they different?
Firstly, register access is asymmetric:
- The EVQ_RPTR table and RX_INDIRECTION_TBL can (or must?) be written
as dwords even though they have a step size of 16 bytes, unlike
most other CSRs.
- In general, a read of any width is valid for registers, so long as
it does not cross register boundaries. There is also no latching
behaviour in the BIU, contrary to rumour.
We write to the EVQ_RPTR table with efx_writed_table() but never read
it back as it's write-only. We write to the RX_INDIRECTION_TBL with
efx_writed_table(), but only read it back for the register dump, where
we use efx_reado_table() as for any other table with step size of 16.
We read MC_TREG_SMEM with efx_readd_table() for the register dump, but
normally read and write it with efx_readd() and efx_writed() using
offsets calculated in bytes.
Since these functions are trivial and have few callers, it's clearer
to open-code them at the call sites. While we're at it, update the
comments on the BIU behaviour again.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Receiving pause frames can block TX queue flushes. Earlier changes
work around this by reconfiguring the MAC during flushes for VFs, but
during flushes for the PF we would only change the fc_disable counter.
Unless the MAC is reconfigured for some other reason during the flush
(which I would not expect to happen) this had no effect at all.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Commit c31e5f9 ('sfc: Add channel specific receive_skb handler and
post_remove callback') added the function pointer field
efx_channel_type::post_remove and an unconditional call through it.
This field should have been initialised to efx_channel_dummy_op_void
in the existing instances of efx_channel_type, but this was only done
in efx_default_channel_type. Consequently, if a device has SR-IOV
enabled then removing the driver or device will result in an oops.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
MCDI supports requests up to 252 bytes long, which is only enough to
pass 63 RX queue IDs to MC_CMD_FLUSH_RX_QUEUES. However a VF may have
up to 64 RX queues, and if we try to flush them all we will generate
an over-length request and BUG() in efx_mcdi_copyin(). Currently
all VF drivers limit themselves to 32 RX queues, so reducing the
limit to 63 does no harm.
Also add a BUILD_BUG_ON in efx_mcdi_flush_rxqs() so we remember to
deal with the same problem there if EFX_MAX_CHANNELS is increased.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
efx_vfdi_set_status_page() validates the peer page count by
calculating the size of a request containing that many addresses and
comparing that with the maximum valid request size (4KB). The
calculation involves a multiplication that may overflow on a 32-bit
system.
We use kcalloc() to allocate memory to store the addresses; that also
does a multiplication and it does check for integer overflow, so any
values larger than 0x1fffffff will be rejected. However, values in
the range [0x1fffffffc, 0x1fffffff] pass boh tests and result in an
attempt to allocate nearly 4GB on the heap. This should be rejected
rather quickly as it's obviously impossible on a 32-bit system, and
indeed the maximum possible heap allocation is 32MB. Still, let's
make absolutely sure by fixing the initial validation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
On the SFC9000 family, each port has 1024 Virtual Interfaces (VIs),
each with an RX queue, a TX queue, an event queue and a mailbox
register. These may be assigned to up to 127 SR-IOV virtual functions
per port, with up to 64 VIs per VF.
We allocate an extra channel (IRQ and event queue only) to receive
requests from VF drivers.
There is a per-port limit of 4 concurrent RX queue flushes, and queue
flushes may be initiated by the MC in response to a Function Level
Reset (FLR) of a VF. Therefore, when SR-IOV is in use, we submit all
flush requests via the MC.
The RSS indirection table is shared with VFs, so the number of RX
queues used in the PF is limited to the number of VIs per VF.
This is almost entirely the work of Steve Hodgson, formerly
shodgson@solarflare.com.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Sucheta Chakraborty