In packet streaming protocol applied to TASCAM FireWire series, the value
of SYT field in CIP header is always zero, therefore it has no meaning.
There's no need to synchronize packets in both direction for the series.
In current implementation of ALSA firewire stack, driver for the series
uses incoming packet parameter for outgoing packet parameter to calculate
the number of data blocks. This can be simplified because the task of
corresponding driver is to transfer data blocks enough to sampling transfer
frequency.
This commit purges support of full duplex synchronization to prevent
over-engineering implementation.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When some tascam units are connected sequentially, userspace
applications are involved at bus-reset state on IEEE 1394 bus. In the
state, any communications can be canceled. Therefore, sound card
registration should be delayed till the bus gets calm.
This commit achieves it.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 3beab0f844 added a member for control and status message, while
it's planned and not implemented yet.
This commit removes it.
Fixes: 3beab0f844fa('ALSA: firewire-tascam: add support for outgoing MIDI messages by asynchronous transaction')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, 'struct snd_tscm_spec' has a member named as 'is_controller' to
identify MIDI controller. This member was originally added to skip
parse control and status messages in isochronous packets for non-controller
model.
As long as I investigate, FW-1804 (non-controller) also transfers the
control and status message, thus it becomes meaningless.
This commit removes it.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This model supports:
* maximum 12 PCM channels for PCM playback
* maximum 18 PCM channels for PCM capture
* 4 ports for MIDI playback
* 4 ports for MIDI capture
* control and status messages in tx isochronous packets
* up to 96.0 kHz
This commit adds support for the model. As the other supported models,
all of available PCM channels are always enabled.
As I described in commit c0949b2785, Ilya Zimnovich had investigated
TASCAM FireWire series in 2011 with his FW-1804. In his report, this model
has internal multiplexer and any software implementation can control it.
Following to the design of ALSA firewire stack, this commit won't
implement it. It should be in userspace via Linux fw character device.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When unsupported models are connected, snd-firewire-tascam module causes
NULL pointer dereference in fw_core_remove_address_handler() (due to
list_del_rcu()).
This commit prevents this bug.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When MIDI buffer stores two or more MIDI messages, TASCAM driver
transfers asynchronous transactions including one MIDI message and
extra bytes from second MIDI message.
This commit fixes this bug by clearing needless bytes in the buffer. The
consumed bytes are already calculated correctly, thus the sequence of
transactions is already correct.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In transactions for MIDI messages, the first byte is used for label and
the rest is for MIDI bytes. In current code, these are handled correctly,
while there's a small mistake for loop condition to include meaningless
statement.
This commit adds two local variables for them and improve the loop
condition.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the callback function of asynchronous MIDI port, the intension of some
local variables are not clear.
This commit improves them. The 'len' variable is used to calculate the
number of MIDI bytes including in the transaction. The 'consume' variable
is used to return the actual number of consumed bytes in ALSA MIDI buffer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the callback function of asynchronous MIDI port, some local variables
are declared 'unsigned int', while they're assigned to int value of return
from snd_rawmidi_transmit_peek().
This commit fixes the type.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The given buffer to callback function is cleared in caller side.
This commit removes buffer initialization in callee side.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Let's leave space for the NUL char otherwise the static checkers
complain that we go beyond the end of the array.
Fixes: 53b3ffee78 ('ALSA: firewire-tascam: change device probing processing')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The contents of Config ROM in firewire device structure are already
aligned to CPU-endianness. Thus, no need to convert it again.
This commit removes needless conversions
Fixes: 9edf723fd858('ALSA: firewire-digi00x: add skeleton for Digi 002/003 family')
Fixes: c0949b278515('ALSA: firewire-tascam: add skeleton for TASCAM FireWire series')
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
My static checker complains because tscm->spec->midi_capture_ports is
either 2 or 4 but the tscm->tx_midi_substreams[] array has 4 elements so
this is possibly off by one. I have looked at the code and I think it
should be >= instead of > as well.
Fixes: 107cc0129a ('ALSA: firewire-tascam: add support for incoming MIDI messages by asynchronous transaction')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We recently tried to add some new code to support turning the LED on and
off but the code in snd_tscm_transaction_reregister() is unreachable.
Fixes: e65e2cb99e ('ALSA: firewire-tascam: Turn on/off FireWire LED')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, this driver picks up model name with be32_to_cpu() macro
to align characters. This is wrong operation because the result is
different depending on CPU endiannness.
Additionally, vendor released several versions of firmware for this
series. It's not better to assign model-dependent information to
device entry according to the version field.
This commit fixes these bugs. The name of model is picked up correctly
and used to identify model-dependent information.
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Fixes: c0949b2785 ('ALSA: firewire-tascam: add skeleton for TASCAM FireWire series')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TASCAM FireWire series has some LEDs on its surface. These LEDs can be
turned on/off by receiving asynchronous transactions to a certain
address. One of the LEDs is labels as 'FireWire'. It's better to light it
up when this driver starts to work. Besides, the LED for 'FireWire' is
turned off at bus reset.
This commit implements this idea.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In former commits, this driver got functionalities to transfer/receive
MIDI messages to/from TASCAM FireWire series.
This commit adds some ALSA MIDI ports to enable userspace applications
to use the functionalities.
I note that this commit doesn't support virtual MIDI ports which console
models support. A physical controls can be assigned to a certain MIDI
ports including physical and virtual. But the way is not clear.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TASCAM FireWire series use asynchronous transaction to receive MIDI
messages. The transaction should be sent to a certain address.
This commit supports the outgoing MIDI messages. The messages in the
transaction includes some quirks:
* One MIDI message is transferred in one quadlet transaction, except for
system exclusives.
* MIDI running status is not allowed, thus transactions always include
status byte.
* The basic data format is the same as transferring MIDI messages
supported in previous commit.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TASCAM FireWire series use asynchronous transaction to transfer MIDI
messages. The transaction is sent to a registered address.
This commit supports the incoming MIDI messages. The messages in the
transaction include some quirks:
* Two quadlets are used for one MIDI message and one timestamp.
* Usually, the first byte of the first quadlet includes MIDI port and MSB
4 bit of MIDI status. For system exclusive message, the first byte
includes MIDI port and 0x04, or 0x07 in the end of the message.
* The rest of the first quadlet includes MIDI bytes up to 3.
* Several set of MIDI messages and timestamp can be transferred in one
block transaction, up to 8 sets.
I note that TASCAM FireWire series ignores ID bytes of system exclusive
message. When receiving system exclusive messages with ID bytes on physical
MIDI bus, the series transfers the messages without ID bytes on IEEE 1394
bus, and vice versa.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds hwdep interface so as the other IEEE 1394 sound devices
has.
This interface is designed for mixer/control applications. By using this
interface, an application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds PCM functionality to transmit/receive PCM samples.
When one of PCM substreams are running or external clock source is
selected, current sampling rate is used. Else, the sampling rate is
changed as an userspace application requests.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds streaming functionality for both direction. To utilize
the sequence of the number of data blocks in packets, full duplex with
synchronization is applied.
Besides, TASCAM FireWire series allows drivers to decide which PCM data
channels are enabled. For convenience, this driver always enable whole the
data channels.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TASCAM FireWire series uses non-blocking transmission for AMDTP packet
streaming, while the format of data blocks is unique.
The CIP headers includes specific value in FMT field and no SYT
information.
In transmitted packets, the first data channel represents event counter,
and the last data channel has status and control information. The rest
has 24bit PCM samples with right padding.
In received packets, all of data channels include 16, 24, 32bit PCM
samples. There's no other kind of information.
This commit adds support for this protocol. For convenience, the size of
PCM samples in outgoing packet is limited by 16 and 24bit. The status and
control information will be supported in future commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TASCAM FireWire series has certain registers for firmware information.
This commit adds proc node to show the information.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TASCAM FireWire series doesn't tell drivers their capabilities, thus
the drivers should have model-dependent parameters and apply it to
detected devices.
This commit adds a structure to represent such parameters.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a new driver for TASCAM FireWire series. In this commit,
this driver just creates/removes card instance according to bus event.
More functionalities will be added in following commits.
TASCAM FireWire series consists of:
* PDI 1394P23 for IEEE 1394 PHY layer
* PDI 1394L40 for IEEE 1394 LINK layer and IEC 61883 interface
* XILINX XC9536XL
* XILINX Spartan-II XC2S100
* ATMEL AT91M42800A
Ilya Zimnovich had investigated TASCAM FireWire series in 2011, and
discover some features of his FW-1804. You can see a part of his research
in FFADO project.
http://subversion.ffado.org/wiki/Tascam
A part of my work are based on Ilya's investigation, while this series
doesn't support the FW-1804, because of a lack of config ROM
information and its protocol detail, especially for PCM channels.
I observed that FW-1884 and FW-1082 don't work properly with 1394 OHCI
controller based on VT6315. The controller can actually communicate packets
to these models, while these models generate no sounds. It may be due to
the PHY/LINK layer issues. Using 1394 OHCI controller produced by the other
vendors such as Texas Instruments may work. Or adding another node on the
bus.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Sakamoto