* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] ibmvscsi: Fix oops when an interrupt is pending during probe
[SCSI] zfcp: Update status read mempool
[SCSI] zfcp: Do not wait for SBALs on stopped queue
[SCSI] zfcp: Fix check whether unchained ct_els is possible
[SCSI] ipr: fix resource path display and formatting
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
davinci: da850/omap-l138 evm: account for DEFDCDC{2,3} being tied high
regulator: tps6507x: allow driver to use DEFDCDC{2,3}_HIGH register
wm8350-regulator: fix wm8350_register_regulator error handling
ab3100: fix off-by-one value range checking for voltage selector
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In TPS6507x, depending on the status of DEFDCDC{2,3} pin either
DEFDCDC{2,3}_LOW or DEFDCDC{2,3}_HIGH register needs to be read or
programmed to change the output voltage.
The current driver assumes DEFDCDC{2,3} pins are always tied low
and thus operates only on DEFDCDC{2,3}_LOW register. This need
not always be the case (as is found on OMAP-L138 EVM).
Unfortunately, software cannot read the status of DEFDCDC{2,3} pins.
So, this information is passed through platform data depending on
how the board is wired.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
When freeing a gpio that has not been exported, gpio_unexport() prints a
debug message when it should just fall through silently.
Example spurious message:
gpio_unexport: gpio0 status -22
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Uwe Kleine-K?nig <u.kleine-koenig@pengutronix.de>
Cc: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MPC85xx EDAC driver is missing module device aliases, so the driver
won't load automatically on boot. This patch fixes the issue by adding
proper MODULE_DEVICE_TABLE() macros.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Dave Jiang <djiang@mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the logic while writing new date/time to the chip. The driver
incorrectly wrote back register values to different registers and even
with wrong mask. The patch adds clearing of the VLF register, which
should be cleared if all date/time values are set.
Signed-off-by: Rudolf Marek <rudolf.marek@sysgo.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Martyn Welch <martyn.welch@gefanuc.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A driver needs to be ready to take an interrupt as soon as it registers
an interrupt handler. I noticed the following oops when testing kdump:
ipr: IBM Power RAID SCSI Device Driver version: 2.5.0 (February 11, 2010)
ibmvscsi 30000002: SRP_VERSION: 16.a
ibmvscsi 30000002: SRP_VERSION: 16.a
Unable to handle kernel paging request for data at address 0x00000000
...
pc: c000000004085e34: .tasklet_action+0xf4/0x1dc
...
c000000004086fe4 .__do_softirq+0x16c/0x2c0
c00000000403138c .call_do_softirq+0x14/0x24
c00000000400ee14 .do_softirq+0xa0/0x104
c00000000408690c .irq_exit+0x70/0xd0
c00000000400f190 .do_IRQ+0x214/0x2a8
c000000004004804 hardware_interrupt_entry+0x1c/0x98
--- Exception: 501 (Hardware Interrupt) at c00000000400c544 .raw_local_irq_restore+0x48/0x54
c00000000465d2a8 ._raw_spin_unlock_irqrestore+0x74/0xa0
c0000000040e7f00 .__setup_irq+0x2ec/0x3f0
c0000000040e8198 .request_threaded_irq+0x194/0x22c
c00000000446d854 .rpavscsi_init_crq_queue+0x284/0x3f0
c00000000446c764 .ibmvscsi_probe+0x688/0x710
c00000000402903c .vio_bus_probe+0x37c/0x3e4
c000000004403f10 .driver_probe_device+0xec/0x1b8
c000000004404088 .__driver_attach+0xac/0xf4
c000000004403184 .bus_for_each_dev+0x98/0x104
c000000004403c98 .driver_attach+0x40/0x60
c0000000044026f0 .bus_add_driver+0x154/0x324
c0000000044045d0 .driver_register+0xe8/0x1ac
c00000000402b2a8 .vio_register_driver+0x54/0x74
c000000004933ea4 .ibmvscsi_module_init+0x80/0xc0
c000000004009834 .do_one_initcall+0x98/0x1d8
c0000000049005b4 .kernel_init+0x27c/0x33c
c000000004031550 .kernel_thread+0x54/0x70
srp_task needs to be setup before request_irq. The patch below fixes the oops.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
s2io: fixing DBG_PRINT() macro
ath9k: fix dma direction for map/unmap in ath_rx_tasklet
net: dev_forward_skb should call nf_reset
net sched: fix race in mirred device removal
tun: avoid BUG, dump packet on GSO errors
bonding: set device in RLB ARP packet handler
wimax/i2400m: Add PID & VID for Intel WiMAX 6250
ipv6: Don't add routes to ipv6 disabled interfaces.
net: Fix skb_copy_expand() handling of ->csum_start
net: Fix corruption of skb csum field in pskb_expand_head() of net/core/skbuff.c
macvtap: Limit packet queue length
ixgbe/igb: catch invalid VF settings
bnx2x: Advance a module version
bnx2x: Protect statistics ramrod and sequence number
bnx2x: Protect a SM state change
wireless: use netif_rx_ni in ieee80211_send_layer2_update
In the case of platform_device_add() fail, we should call
platform_device_put() instead of platform_device_del()
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
We use voltage selector as an array index for typ_voltages.
Thus the valid range for voltage selector should be 0..voltages_len-1.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Patch 9e39f7c5b3 changed the
DBG_PRINT() macro and the if clause was wrongly changed. It means
that currently all the DBG_PRINT are being printed, flooding the
kernel log buffer with things like:
s2io: eth6: Next block at: c0000000b9c90000
s2io: eth6: In Neterion Tx routine
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Sreenivasa Honnur <Sreenivasa.Honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
MIPS: Set io_map_base for several PCI bridges lacking it
MIPS: Alchemy: Define eth platform devices in the correct order
MIPS: BCM63xx: Prevent second enet registration on BCM6338
MIPS: Quit using undefined behavior of ADDU in 64-bit atomic operations.
MIPS: N32: Define getdents64.
MIPS: MTX-1: Fix PCI on the MeshCube and related boards
MIPS: Make init_vdso a subsys_initcall.
MIPS: "Fix" useless 'init_vdso successfully' message.
MIPS: PowerTV: Move register setup to before reading registers.
SOUND: Au1000: Fix section mismatch
VIDEO: Au1100fb: Fix section mismatch
VIDEO: PMAGB-B: Fix section mismatch
VIDEO: PMAG-BA: Fix section mismatch
NET: declance: Fix section mismatches
VIDEO. gbefb: Fix section mismatches.
Fix error from the last pull request. Making sure we shut the panel off
is more correct and saves power.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: musb: tusb6010: fix compile error with n8x0_defconfig
USB: FTDI: Add support for the RT System VX-7 radio programming cable
USB: add quirk for Broadcom BT dongle
USB: usb-storage: fix initializations of urb fields
USB: xhci: Set Mult field in endpoint context correctly.
USB: sisusbvga: Fix for USB 3.0
USB: adds Artisman USB dongle to list of quirky devices
USB: xhci: Set EP0 dequeue ptr after reset of configured device.
USB: Fix USB3.0 Port Speed Downgrade after port reset
USB: xHCI: Fix another bug in link TRB activation change.
USB: option: Add support for AMOI Skypephone S2
USB: New PIDs for Qualcomm gobi 2000 (qcserial)
USB: ftdi_sio: support for Signalyzer tools based on FTDI chips
USB: s3c2410_udc: be aware of connected gadget driver
USB: Expose vendor-specific ACM channel on Nokia 5230
USB: Add PID for Sierra 250U to drivers/usb/serial/sierra.c
USB: option: add support for 1da5:4518
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: add pipe A force quirks to i915 driver
drm/i915: Fix panel fitting regression since 734b4157
drm/i915: fix deadlock in fb teardown
drm/i915: don't free non-existent compressed llb on ILK+
agp/intel: Use the correct mask to detect i830 aperture size.
drm/i915: disable FBC when more than one pipe is active
drm/i915: Use the correct scanout alignment for fbcon.
drm/i915: make sure eDP panel is turned on
drm/i915: add PANEL_UNLOCK_REGS definition
drm/i915: Make G4X-style PLL search more permissive
drm/i915: Clear any existing dither mode prior to enabling spatial dithering
drm/i915: handle shared framebuffers when flipping
drm/i915: Explosion following OOM in do_execbuffer.
gpu/drm/i915: Add a blacklist to omit modeset on LID open
395913d0b1 ("[CPUFREQ] remove rwsem lock
from CPUFREQ_GOV_STOP call (second call site)") is not needed, because
there is no rwsem lock in cpufreq_ondemand and cpufreq_conservative
anymore. Lock should not be released until the work done.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=1594
Signed-off-by: Andrej Gelenberg <andrej.gelenberg@udo.edu>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Drop the unnecessary empty stubs in tusb6010.c and avoid
a compile error when building kernel for n8x0.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
RT Systems has put out bunch of ham radio cables based on the FT232RL
chip. Each cable type has a unique PID, this adds one for the Yaesu VX-7
radios.
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This device needs to be reset when resuming
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 0ede76fcec, "USB: remove uses of
URB_NO_SETUP_DMA_MAP" introduced a regression by inadvertantly removing
initialization of the transfer flags. This caused initialization
failures in the ums-karma driver. Fix the regression by zeroing it.
While at it, as Alan Stern points out, the initializers for
actual_length and status are handled by the core and error_count
only matters for isochronous urbs, so they don't need to be set here.
Remove them.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bmAttributes field of the SuperSpeed Endpoint Companion Descriptor has
different meanings, depending on the endpoint type. If the endpoint is
isochronous, the bmAttributes field is the maximum number of packets
within a service interval that this endpoint supports. If the endpoint is
bulk, it's the number of stream IDs this endpoint supports.
Only set the Mult field of the xHCI endpoint context using the
bmAttributes field if the endpoint is isochronous, and the device is a
SuperSpeed device.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Super speed is also fast enough to let sisusbvga operate.
Therefor expand the checks.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When an attempt is made to read the interface strings of the Artisman
Watchdog USB dongle (idVendor:idProduct 04b4:0526) an error is written
to the dmesg log (uhci_result_common: failed with status 440000) and the
dongle resets itself, resulting in a disconnect/reconnect loop.
Adding the dongle to the list of devices in quirks.c, with the same
quirk Alan Stern's previous patch for the Saitek Cyborg Gold 3D
joystick, stops the device from resetting and allows it to be used with
no problems.
Signed-off-by: Paul Mortier <mortier@btinternet.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a configured device is reset, the control endpoint's ring is reused.
If control transfers to the device were issued before the device is reset,
the dequeue pointer will be somewhere in the middle of the ring. If the
device is then issued an address with the set address command, the xHCI
driver must provide a valid input context for control endpoint zero.
The original code would give the hardware the original input context,
which had a dequeue pointer set to the top of the ring. This would cause
the host to re-execute any control transfers until it reached the ring's
enqueue pointer. When issuing a set address command for a device that has
just been configured and then reset, use the control endpoint's enqueue
pointer as the hardware's dequeue pointer.
Assumption: All control transfers will be completed or cancelled before
the set address command is issued to the device. If there are any
outstanding control transfers, this code will not work.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without this fix, a USB 3.0 port is downgraded to full speed after a port
reset of a configured device. The USB 3.0 terminations will be disabled
permanently, and USB 3.0 devices will always enumerate as full speed
devices, until the host controller is unplugged (if it is an ExpressCard)
or the computer is rebooted.
Fajun Chen traced this traced the speed downgrade issue to the port reset
and the interpretation of port status in USB hub driver code. The hub
code was not testing for the port being a SuperSpeed port, and it fell
through to the else case of Full Speed.
The following patch adds SuperSpeed mapping from the port status, and
fixes the speed downgrade issue.
Reported-by: Fajun Chen <fajun.chen@seagate.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 6c12db90f1 also seems to have
introduced a bug that is triggered when the command ring is about to wrap.
The inc_enq() function will not have moved the enqueue pointer past the
link TRB. It is supposed to be moved past the link TRB in prepare_ring(),
which should be called before a TD is enqueued. However, the
queue_command() function never calls the prepare_ring() function because
prepare_ring() is only supposed to be used for endpoint rings. That means
the enqueue pointer will not be moved past the link TRB, and will get
overwritten.
The fix is to make queue_command() call prepare_ring() with a fake
endpoint status (set to running). Then the enqueue pointer will get moved
past the link TRB.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usbserial: Add AMOI Skypephone S2 support.
This patch adds support for the AMOI Skypephone S2 to the usbserial module.
Tested-by: Dennis Jansen <Dennis.Jansen@web.de>
Signed-off-by: Dennis Jansen <Dennis.Jansen@web.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support for the Generic Qualcomm Gobi 2000 WWAN UMTS/CDMA modem
Signed-off-by: Andrew Bird <ajb@spheresytems.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi_sio: support for Signalyzer tools based on FTDI chips
This patch adds support for the Xverve Signalyzers.
Signed-off-by: Colin Leitner <colin.leitner@googlemail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To escape from data abort in interrupt handler, it is required to
check for a connected gadget before delivering control requests.
The change fixes the following panic, which occurs with no loaded
gadget driver and input USB_REQ_GET_DESCRIPTOR request:
Kernel panic - not syncing: Fatal exception in interrupt
[<c0025874>] (unwind_backtrace+0x0/0xd8) from [<c0253f14>] (panic+0x40/0x110)
[<c0253f14>] (panic+0x40/0x110) from [<c002470c>] (die+0x154/0x180)
[<c002470c>] (die+0x154/0x180) from [<c0026448>] (__do_kernel_fault+0x64/0x74)
[<c0026448>] (__do_kernel_fault+0x64/0x74) from [<c0026610>] (do_page_fault+0x1b8/0x1cc)
[<c0026610>] (do_page_fault+0x1b8/0x1cc) from [<c00202d4>] (do_DataAbort+0x34/0x94)
[<c00202d4>] (do_DataAbort+0x34/0x94) from [<c0020a60>] (__dabt_svc+0x40/0x60)
Exception stack(0xc0327ea8 to 0xc0327ef0)
7ea0: bf0026b0 c0327ef0 c0327ee4 00000000 bf002590 00000093
7ec0: 00000001 bf0026b0 bf002990 00000000 00000008 0000143d 00003f00 c0327ef0
7ee0: bf001364 bf001360 20000093 ffffffff
[<c0020a60>] (__dabt_svc+0x40/0x60) from [<bf001360>] (s3c2410_udc_irq+0x5b8/0x778 [s3c2410_udc])
[<bf001360>] (s3c2410_udc_irq+0x5b8/0x778 [s3c2410_udc]) from [<c0058aa0>] (handle_IRQ_event+0x3c/0x104)
[<c0058aa0>] (handle_IRQ_event+0x3c/0x104) from [<c005a428>] (handle_edge_irq+0x12c/0x164)
[<c005a428>] (handle_edge_irq+0x12c/0x164) from [<c0020068>] (asm_do_IRQ+0x68/0x88)
[<c0020068>] (asm_do_IRQ+0x68/0x88) from [<c0020aa4>] (__irq_svc+0x24/0xa0)
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Nokia S60 phones expose two ACM channels. The first is
a modem, the second is 'vendor-specific' but is treated
as a serial device at the S60 end, so we want to expose
it on Linux too.
Signed-off-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add VID/PID for Sierra Wireless 250U USB dongle to sierra.c
Allows use of 3G radio only
Signed-off-by: August Huber <gus@pbx.org>
Cc: Elina Pasheva <epasheva@sierrawireless.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ported over from the old UMS list. Unfortunately they're still
necessary especially on older laptop platforms.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=22126.
Tested-by: Xavier <shiningxc@gmail.com>
Tested-by: Diego Escalante Urrelo <diegoe@gnome.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The crtc mode fixup is run after the encoders adjust the mode to fit on
their output, so don't reset the mode!
Fixes:
Bug 29057 - display corruption under 800x600 on netbook
(1024x600) with 'Full Aspect' scaling
https://bugs.freedesktop.org/show_bug.cgi?id=29057
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Xun Fang <xunx.fang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For edma, we should use DMA_BIDIRECTIONAL, or else use
DMA_FROM_DEVICE.
This is found to address "BUG at arch/x86/mm/physaddr.c:5"
as described here:
http://lkml.org/lkml/2010/7/14/21
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At module unload time we'll tear down the fbdev state. We do so under
the struct mutex, so we shouldn't try to use the unlocked variant of
the GEM object unreference function or we may deadlock.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
We should only free the compressed llb if we allocated it in the first
place otherwise we'll panic at unload time.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
BugLink: https://bugs.launchpad.net/bugs/597075
commit f1befe71fa introduced a
regression when detecting aperture size of some i915 adapters, e.g.,
those on the Intel Q35 chipset.
The original report: https://bugzilla.kernel.org/show_bug.cgi?id=15733
The regression report: https://bugzilla.kernel.org/show_bug.cgi?id=16294
According to the specification found at
http://intellinuxgraphics.org/VOL_1_graphics_core.pdf, the PCI config
space register I830_GMCH_CTRL is a mirror of GMCH Graphics
Control. The correct macro for isolating the aperture size bits is
therefore I830_GMCH_GMS_MASK along with the attendant changes to the
case statement.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Tested-by: Kees Cook <kees.cook@canonical.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Eric Anholt <eric@anholt.net>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
We're really supposed to do this to avoid trouble with underflows when
multiple planes are active.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=26987.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: fangxun <xunx.fang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This fixes a potential modesetting error during boot with plymouth on
Broadwater and Crestline introduced with 9df47c. The framebuffer was
hard-coding an alignment of 64K, but the modesetting code required the
documented alignment of 128K. The result was that we would attempt to
unbind the pinned fbcon buffer, triggering an ERROR and ultimately
failing the mode change.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
When enabling the eDP port, we need to make sure the panel is turned on
after training the link. If we don't, it likely won't come back after
suspend or may not come up at all.
For unknown reasons, unlocking the panel regs before initiating a power
on sequence is necessary. There are known bugs in the PCH panel
sequencing logic, apparently this is one possible workaround.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=28739.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: "Paulo J. S. Silva" <pjssilva@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In some cases, unlocking the panel regs is safe and can help us avoid a
flickery, full mode set sequence. So define the unlock key and use it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes an Ironlake laptop with a 68.940MHz 1280x800 panel and 120MHz SSC
reference clock.
More generally, the 0.488% tolerance used before is just too tight to
reliably find a PLL setting. I extracted the search algorithm and
modified it to find the dot clocks with maximum error over the valid
range for the given output type:
http://people.freedesktop.org/~ajax/intel_g4x_find_best_pll.c
This gave:
Worst dotclock for Ironlake DAC refclk is 350000kHz (error 0.00571)
Worst dotclock for Ironlake SL-LVDS refclk is 102321kHz (error 0.00524)
Worst dotclock for Ironlake DL-LVDS refclk is 219642kHz (error 0.00488)
Worst dotclock for Ironlake SL-LVDS SSC refclk is 84374kHz (error 0.00529)
Worst dotclock for Ironlake DL-LVDS SSC refclk is 183035kHz (error 0.00488)
Worst dotclock for G4X SDVO refclk is 267600kHz (error 0.00448)
Worst dotclock for G4X HDMI refclk is 334400kHz (error 0.00478)
Worst dotclock for G4X SL-LVDS refclk is 95571kHz (error 0.00449)
Worst dotclock for G4X DL-LVDS refclk is 224000kHz (error 0.00510)
Signed-off-by: Adam Jackson <ajax@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
Linus Torvalds