This patch allows SoC-specific CAR initialization routines to register
their own reset_assert and reset_deassert callbacks with the common Tegra
CAR code. If defined, the common code will call these callbacks when a
reset control with number >= num_periph_banks * 32 is attempted to be asserted
or deasserted respectively. Numbers greater than or equal to num_periph_banks * 32
are used to avoid clashes with low numbers that are automatically mapped to
standard CAR reset lines.
Each SoC with these special resets should specify the defined reset control
numbers in a device tree header file.
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The EMC clock driver uses symbols exported by the EMC driver, so it
needs the corresponding dependency to avoid build breakage.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The driver is currently only tested on Tegra124 Jetson TK1, but should
work with other Tegra124 boards, provided that correct EMC tables are
provided through the device tree. Older chip models have differing
timing change sequences, so they are not currently supported.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
[treding@nvidia.com: use more consistent function names]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently the Tegra clock driver simplifies the clock tree somewhat by
taking advantage of the fact that clk_m runs at the same frequency as
the oscillator. While that's true on all currently supported SoCs, it
does not apply to Tegra210 anymore. On Tegra210 clk_m is typically
divided down from the oscillator frequency. To support that setup, add
a separate clock for the oscillator that both clk_m and pll_ref derive
from.
Modify the tegra_osc_clk_init() function to take an additional divider
parameter for clk_m. Existing SoCs always pass in 1, whereas Tegra210
will read the divider from a register in the clock & reset controller.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The clock initialization structure is named struct clk_init_table.
Update the kerneldoc comment to use the correct name.
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The memory controller clock runs either at half or the same frequency as
the EMC clock.
Reviewed-By: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Now that no code uses the custom Tegra module reset API, we can remove
its implementation.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
The Tegra CAR module implements both a clock and reset controller. So
far, the driver exposes the clock feature via the common clock API and
the reset feature using a custom API. This patch adds an implementation
of the common reset framework API (include/linux/reset*.h). The legacy
reset implementation will be removed once all drivers have been
converted.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Tegra124 has a clock which consists of a mux and a fractional divider.
Add support for this.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 has periph clocks which share the hw register. Hence locking is
required.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Introduce a common function which performs super clock initialization for
Tegra114 and beyond.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Introduce new files for fixed and PMC clocks common between several Tegra
SoCs and move Tegra114 to this new infrastructure.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Introduce a new file for peripheral clocks common between several Tegra
SoCs and move Tegra114 to this new infrastructure. Also PLLP and the PLLP_OUT
clocks will be initialized here.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Move audio clocks and PLLA initialization to a common file so it can be used by
multiple Tegra SoCs. Also a new array tegra114_clks is introduced for Tegra114
which specifies which common clocks are available on Tegra114 and what their
DT IDs are.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Add a common infra for registering clkdev. This allows decoupling clk
registration from clkdev registration.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Move some fields related to the PLL HW description to the tegra_clk_pll_params.
This allows some PLL code to be moved to common files later.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
This flag indicates the peripheral clock does not have a divider. It will
simplify the initialization tables and avoids some very similar code.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
This patch makes periph_clk_enb_refcnt a global array, dynamically allocated
at boottime. It simplifies the macros somewhat and allows clocks common to
several Tegra SoCs to be defined in a separate files. Also the clks array
becomes global and dynamically allocated which allows the DT registration to
be moved to a generic funcion.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
This patch determines the register bank for clock enable/disable and reset
based on the clock ID instead of hardcoding it in the tables describing the
clocks. This results in less data to be maintained in the tables, making the
code easier to understand. The full benefit of the change will be realized once
also other clocktypes will be table based.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Add DFLL DVCO reset line control functions to the CAR IP block driver.
The DVCO present in the DFLL IP block has a separate reset line,
exposed via the CAR IP block. This reset line is asserted upon SoC
reset. Unless something (such as the DFLL driver) deasserts this
line, the DVCO will not oscillate, although reads and writes to the
DFLL IP block will complete.
Thanks to Aleksandr Frid <afrid@nvidia.com> for identifying this and
saving hours of debugging time.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Aleksandr Frid <afrid@nvidia.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add clock functions to initialize, enable, and disable the FCPU clock
shapers, based on the FCPU voltage rail state. These will be used by
the DFLL clocksource driver code.
This version of the patch contains a fix for a problem noticed by Andrew
Chew <achew@nvidia.com>, where some of the FINETRIM_R bitfields were
incorrectly defined.
Based on code originally written by Aleksandr Frid <afrid@nvidia.com>.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Andrew Chew <achew@nvidia.com>
Reviewed-by: Andrew Chew <achew@nvidia.com>
Cc: Matthew Longnecker <mlongnecker@nvidia.com>
Cc: Aleksandr Frid <afrid@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
PLLM can have override bits in the PMC. Describe those in the PLL parameters.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The m,n,p fields don't have the same bit offset and width across all PLLs.
This patch allows SoC specific files to indicate the offset and width.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Use common of_clk_init() function for clocks initialization.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Workaround a hardware bug in MSENC during clock enable.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
We will need some tegra peripheral clocks with the CLK_IGNORE_UNUSED flag,
most notably mselect, which is a bridge between AXI and most peripherals.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra114 introduces new PLL types. This requires new clocktypes as well
as some new fields in the pll structure.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
PLLC2 and PLLC3 on Tegra114 have separate phaselock and frequencylock bits.
So switch to a lock mask to be able to test both at the same time.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Some PLLs in Tegra114 don't use a power of 2 mapping for the post divider.
Introduce a table based approach and switch PLLU to it.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra114 PLLC2 and PLLC3 don't have a lock enable bit. The lock bits are
always functional.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Not all PLLs in Tegra114 have a bypass bit. Adapt the common code to only use
this bit when available.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Refactor the PLL programming code to make it useable by the new PLL types
introduced by Tegra114.
The following changes were done:
* Split programming the PLL into updating m,n,p and updating cpcon
* Move locking from _update_pll_cpcon() to clk_pll_set_rate()
* Introduce _get_pll_mnp() helper
* Move check for identical m,n,p values to clk_pll_set_rate()
* struct tegra_clk_pll_freq_table will always contain the values as defined
by the hardware.
* Simplify the arguments to clk_pll_wait_for_lock()
* Split _tegra_clk_register_pll()
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tegra clock driver is initialized during the ARM machine descriptor's
.init_irq() hook. It can't be initialized earlier, since dynamic memory
usage is required. It can't be initialized later, since the .init_timer()
hook needs the clocks initialized. However, at this time, udelay()
doesn't work.
The Tegra clock initialization table may enable some PLLs. Enabling a PLL
may require usage of udelay(). Hence, this can't happen right when the
clock driver is initialized.
To solve this, separate the clock driver initialization from the clock
table processing, so they can execute at separate times.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add a table lookup feature to the mux clock. Also allow arbitrary masks
instead of the width. This will be used by some clocks on Tegra114. Also
adapt the tegra periph clk because it uses struct clk_mux directly.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add Tegra30 clock support based on common clock framework.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: ensure all OF lookups return valid cookies i.e. an explicit
error pointer or valid pointer not NULL, adapt to renames in earlier
patches, fixed some checkpatch issues.]
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add Tegra20 clock support based on common clock framework.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: s/1GHz/100MHz/ in call to tegra_clk_plle() to fix PCIe,
implemented KBC clock, ensure all OF lookups return valid cookies i.e.
an explicit error pointer or valid pointer not NULL, adapt to renames
in earlier patches, fixed some checkpatch issues.]
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add Tegra specific clocks, pll, pll_out, peripheral, frac_divider, super.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: alloc sizeof(*foo) not sizeof(struct foo), add comments re:
storing pointers to stack variables, make a timeout loop more idiomatic,
use _clk_pll_disable() not clk_disable_pll() from _program_pll() to
avoid redundant lock operations, unified tegra_clk_periph() and
tegra_clk_periph_nodiv(), unified tegra_clk_pll{,e}, rename all clock
registration functions so they don't have the same name as the clock
structs, return -EINVAL from clk_plle_enable when matching table rate
not found, pass ops to _tegra_clk_register_pll rather than a bool.]
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Mikko Perttunen