This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.
This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
[Vasu.Dev: v2
Also converted pmcraid_change_queue_depth and then verified
all modules compile using "make allmodconfig" for any new build
warnings on X86_64.
Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Bump version to 03.100.03.00
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
(1) target resets are sending link change rate events with no link rate
change -> thus said the driver was modified so when there is no link rate
change, we don't need to call mpt2sas_transport_update_links nor
_scsih_ublock_io_device.
(2) There were changes made in _scsih_sas_topology_change_event_debug to
change the debug strings so they are more clear. Also the link rate change
information was added to display the new and previous link rate.
for the MPI2_EVENT_SAS_TOPOLOGY_CHANGE_LIST event when the ExpStatus is
set to zero, display "responding" instead of "unknown status".
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
(1) Added new function _scsih_ir_shutdown. This function will issue the
MPI2_RAID_ACTION_SYSTEM_SHUTDOWN_INITIATED request via
MPI2_FUNCTION_RAID_ACTION. The function will wait 10 seconds for reply
message frame, then print out the ioc status and loginfo. This function is
only called when there are raid volumes present.
(2) Add shutdown callback in the struct pci_driver object scsih_driver. This
will be called only when the system is shutting down. From this function, we
will call _scsih_ir_shutdown mentioned above.
(3) Add support in _scsih_remove to call _scsih_ir_shutdown. The function
_scsih_remove will be called when the driver is unloaded (and system is
still running).
scsih internal command contex is added to send internal message frames
from mpt2sas_scsih.c.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When receiving the MPI2_EVENT_SAS_DEV_STAT_RC_INTERNAL_DEVICE_RESET event,
the driver will set the tm_busy flag in the sdev private host data, When
tm_busy flag is set, the driver will return SCSI_MLQUEUE_DEVICE_BUSY,
effectly freezing the IO to the device. The tm_busy flag is cleared with the
MPI2_EVENT_SAS_DEV_STAT_RC_CMP_INTERNAL_DEV_RESET event.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
(1) EEDP(End to End data protection) was not working. This was due to not
setting EEDP BlockSize and Flags to little endian format in the message
frame.
(2) Some expander sysfs attributes were not getting set properly. The sas
format was not getting set due to endian issues with sas_format field in the
struct rep_manu_reply. Since sas_format was not set properly, the
component_vendor_id, component_revision_id, and component_id were not set.
(3) In _transport_smp_handler: we don't need to convert the smid from little
endian to cpu prior to calling mpt2sas_base_free_smid, because its allready
in cpu format. (4) Some loginfos and ioc status were not xonverted from
little endian to cpu.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
cpu_to_le64 when calculating the physical dma address. This will properly
handle endianess on big endian systems. The return value of this function
was changed from dma_addr_t to __le64. Remove the typecasting of u32 when
setting the SenseBufferLowAddress, since its already in __le32 format.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
1 Its observed that the OS was sending request to the driver after it had been
put into blocking state, so the driver was modified to return
SCSI_MLQUEUE_DEVICE_BUSY.
2. Driver will return DID_TRANSPORT_DISRUPTED when sdev is haivng nexus loss.
This occurrs when sdev is blocked, between the
MPI2_EVENT_SAS_TOPO_RC_DELAY_NOT_RESPONDING and
MPI2_EVENT_SAS_TOPO_RC_TARG_NOT_RESPONDING events.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The driver needs to retrieve the ioc facts prior to putting the controller
into READY state. The current design is calling ioc facts after putting the
controller into READY state, which means the driver is sending a diag reset
instead of message unit reset becuase the capability information is not yet
available.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
(1) for the MPI2_EVENT_IR_OPERATION_STATUS event, add support to print
"background init" or "make data consistent" for debugging purposes. If the
RAIDOperation is set to a value not defined, then don't print anything
(2) for the MPI2_EVENT_SAS_DEVICE_STATUS_CHANGE event, add support to print
"expander reduced functionality" and "expander reduced functionality
complete", which are new events.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added sanity check in _scsih_change_queue_depth to limit the max_depth to 32
for SATA devices. This is only for physical devices not part of a volume.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added support to set the TimeStamp when sending ioc_init.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added tests for registry entries of EXBuffSize, EXImmed, and EXType to
support the new Extended diag buffer type. Modified code where necessary to
handle the new ExtendedType field in the F/W diagnostic Post and Release
messages.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added command line option diag_buffer_enable. When the command line option is
set, the driver will automatically post diag buffers at driver load time.
The command line option diag_buffer_enable is bitwise, so it's possible to
enable both and/or snapshot + trace buffers. For trace, the driver will
allocate 1MB buffer, whereas for snapshot its 2MB. The purpose for this is
so the enduser doesn't have to manually use an application to setup diag
buffers for debugging firmware related issues.
Here is some examples
trace:
# insmod mpt2sas.ko diag_buffer_enable=1
snapshot:
# insmod mpt2sas.ko diag_buffer_enable=2
both trace and snapshot:
# insmod mpt2sas.ko diag_buffer_enable=3
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fixed some of the comments sections for some of the function so "@ioc:
pointer to scsi command object" was changed to "@ioc: per adapter object"
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added command line option and shost sysfs attribute called
mpt2sas_fwfault_debug. When enduser writes a "1" to this parameter, this
will enable support in the driver for debugging firmware timeout related
issues. This handling was added in three areas (a) scsi error handling
callback called task_abort, (b) IOCTL interface, and (c) other timeouts that
result in diag resets, such as manufacturing config pages. When this
support is enabled, the driver will provide dump_stack to console, halt
controller firmware, and panic driver. The end user probably would want to
setup serial console redirection so the dump stack can be seen.
Here are the three methods for enable this support:
(a) # insmod mpt2sas.ko mpt2sas_fwfault_debug=1
(b) # echo 1 > /sys/module/mpt2sas/parameters/mpt2sas_fwfault_debug
(c) # echo 1 > /sys/class/scsi_host/host#/fwfault_debug (where # is
the host number)
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The new headers contain the following changes:
(1) Added IO Unit Page 7.
(2) Added new device ids for SAS2208.
(3) Added SAS IO Unit Page 5.
(4) Added partial and slumber power management capable flags to SAS Device
Page 0 Flags field.
(5) Added PhyInfo defines for power condition.
(6) Added Ethernet configuration pages.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add support in the driver to check for valid response info in the scsi
state, then check to see if the response code is
MPI2_SCSITASKMGMT_RSP_INVALID_FRAME; when this condition occurrs, the driver
will return DID_SOFT_ERROR. A return code of DID_SOFT_ERROR will result in
a retry at the scsi-mid layer level. An additional change added to obtain
the response code from the 1st byte of the response info instead of last.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This handles the case where driver receives a expander removal event while
it is in the middle of processing an expander add event. The existing
implementation will stop processing futher device adds when a expander
delete arrives on top of add expander add. Due to a sanity check in the
driver, the devices there were not added, were never handshaked to firmware
with the device removal handshake protocal. Since the driver didnt' do the
handshake, the controller never provide further add events. To fix this
issue, the sanity check was removed so the driver will always do the device
removal handshake protocal.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The device driver was not handling updating device handles in all cases
across diag resets. To fix this issue, the driver is converted to using sas
address instead of handle as a lookup reference to the parent expander or
sas_host. Also, for both expanders and sas host, the phy handle will be one
unique handle. In the sas host case, the phy handle can be different for
every phy, so the change is to set the handle to the handle of the first
phy; every phy will be one single sas address(phy 0) instead of a different
sas address for every phy(previous implementation). So making one consistent
sas address for all the direct attachedports to the sas host, will make it
better user experience when using udev /dev/disk/by-path dev nodes
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add support to process device removal events when the phy status is set to
MPI2_EVENT_SAS_TOPO_PHYSTATUS_VACANT.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Following a diag_reset, a request to send an ioc_init is timing out. The
timeout occurred within the HANDSHAKE logic while waiting on firmware to
acknowledge that the driver had wrote to the doorbell register. This was
root caused to a logic timeout in the firmware code. The proposed solution
is for the driver to call the udelay instead of msleep API in function where
its looping reading the interrupt status. In addition to this change, there
were two additional cases where we deleted the clearing interrupt status
outside handshake context.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Now driver call init_completion on a per request basis. At some
point the wait_for_completion_timeout is not waiting for the timeout,
instead returning immediately, thus going into diag reset. This fix will
address all request using the wait_for_completion_timeout API. The previous
implimentation was only calling init_completion at driver
load time.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
(1) Added three new functions to handle sending target resest and OP_REMOVE
from interrupt time, they are _scsih_tm_tr_send, _scsih_tm_tr_complete, and
_scsih_sas_control_complete. This code will create a link list of pending
target resets if there is no more available request in the hipriority
request queue. The list is stored in ioc->delayed_tr_list.
(2) All callback handler return type is changed from void to u8.
Now _base_interrupt will check for return type of callback handlers to
take decision of message frame is already freed or not.
In genral,
Return 1 meaning mf should be freed from _base_interrupt
0 means the mf is freed from function.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
1) create a pool of high priority message frames in the region of memory
between message frames and chains. The modifications are in
_base_allocate_memory_pools. Also create a seperate pool of memory for
internal commands located near the same region of memory. The pool of high
priority message frames is restriced by the facts->HighPriorityCredit.
2) Create additional API for accessing request message frames. New function
mpt2sas_base_get_smid_hpr is for highpriority request. New function
mpt2sas_base_get_smid_scsiio for SCSI_IO, passing in the scsi command
pointer. The mpt2sas_base_get_smid function is for requesting internal
commands.
3) Added new function _base_get_cb_idx to obtain the callback
index from one of the three pools of request message frames.
4) Removed wrapper functions _scsih_scsi_lookup_set and
_scsih_scsi_lookup_getclear. These were removed because this handling was
moved into mpt2sas_base_get_smid_scsiio and mpt2sas_base_free_smid.
5) The function mpt2sas_base_free_smid is modified so the request message
frames are put back on one of the three pools of request message frames.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Update the copyright year to 2009 through out the code.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added new file for MPI2 header version history.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Drivers header are updated to the MPI2 REV K headers.
Renamed VF_ID to msix_index in all call back handlers.
VF_ID is removed from all request descriptor.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Bump version to 01.100.06.00
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by:: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Cleaned up base_interrupt routine to be more effiecent.
Deleted about a third of the config page API by moving redundant code from all
the calling functions to _config_request.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch modifies the slave_configure callback so the messages that get sent
to system log for RAID1E volumes contain the string "RAID10" instead of
"RAID1E". These messages contain information regarding what kind of scsi device
is being added. Certain OEMS can enable displaying the RAID10 string instead of
RAID1E via manufacturing page 10. The driver will read this config page at
driver load time, then determine from the GenericFlags0 bits whether display
the RAID10 or RAID1E string, also even drive count is taken into consideration.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <Eric.moore@lsi.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Changing SDEV Running state from interrupt context. Previously It was
handle in work queue thread. With this change It will not wait for work
queue thread to execute scsih_ublock_io_device to put SDEV into Running
state. This will reduce delay for Device becoming RUNNING.
Modified this patch considering James comment "Not to change SDEV state
using scsi_device_set_state API, instead use scsi_internal_device_unblock
scsi_internal_device_block API"
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <Eric.moore@lsi.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Deleted the wrapper function called _scsih_link_change. This function was
implemented for compatibility reasons only, between different kernel versions.
Currently this function is no longer needed. The calling function are
converted to calling mpt2sas_transport_update_phy_link_change directly in the
transport layer.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch renames the flag for indicating host reset from
ioc_reset_in_progress to shost_recovery. It also removes the spin locks
surrounding the setting of this flag, which are unnecessary. Sanity checks on
the shost_recovery flag were added thru out the code so as to prevent sending
firmware commands during host reset. Also, the setting of the shost state to
SHOST_RECOVERY was removed to prevent deadlocks, this is actually better
handled by the shost_recovery flag.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <Eric.moore@lsi.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Following host reset its possible that the controller firmware could
assign new handles for devices, as well as adding or deleting devices. There is
code in the driver that will rescan the topology folowing host reset; updating
device handles, and remove devices that are no longer responding. This patch
will improve the responsivness by moving this rescaning from the delayed hotplug
worker thread to immediately following the host reset.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <Eric.moore@lsi.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Moving the setting and clearing of the mutex's to
_config_request. There was a mutex deadlock when diag reset is called from
inside _config_request, so diag reset was moved to outside the mutexs.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix another ocurring when the system resumes. This oops was due to driver
setting the pci drvdata to NULL on the prior hibernation. Becuase it was
set to NULL, upon resmume we assume the pci drvdata is non-zero, and we oops.
To fix the ooops, we don't set pci drvdata to NULL at hibernation time.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix oops ocurring at hibernation time. This oops was due to the firmware fault
watchdog timer still running after we freed resources. To fix the issue we need
to terminate the watchdog timer at hibernation time.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This restriction is introduced just to avoid loop of
config_request. Retry must be limited so we have restricted
config request to maximum 2 times.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Inhibit 0x3117 loginfos - during cable pull, there are too many printks going
to the syslog, this is have impact on how fast the interrupt routine can handle
keeping up with command completions; this was the root cause to the config
pages timeouts.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When a volume is activated, the driver will recieve a pair of ir config change
events to remove the foreign volume, then add the native.
In the process of the removal event, the hidden raid componet is removed from
the parent.When the disks is added back, the adding of the port fails becuase
there is no instance of the device in its parent.
To fix this issue, the driver needs to call mpt2sas_transport_update_links()
prior to calling _scsih_add_device. In addition, we added sanity checks on
volume add and removal to ignore events for foreign volumes.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kernel panic is seen because driver did not tear down the port which should
be dnoe using mpt2sas_transport_port_remove(). without this fix When expander
is added back we would oops inside sas_port_add_phy.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kernel panic is seen because of enclosure_handle received from FW is zero.
Check is introduced before calling mpt2sas_config_get_enclosure_pg0.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Conflicts:
drivers/message/fusion/mptsas.c
fixed up conflict between req->data_len accessors and mptsas driver updates.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'for-2.6.31' of git://git.kernel.dk/linux-2.6-block: (153 commits)
block: add request clone interface (v2)
floppy: fix hibernation
ramdisk: remove long-deprecated "ramdisk=" boot-time parameter
fs/bio.c: add missing __user annotation
block: prevent possible io_context->refcount overflow
Add serial number support for virtio_blk, V4a
block: Add missing bounce_pfn stacking and fix comments
Revert "block: Fix bounce limit setting in DM"
cciss: decode unit attention in SCSI error handling code
cciss: Remove no longer needed sendcmd reject processing code
cciss: change SCSI error handling routines to work with interrupts enabled.
cciss: separate error processing and command retrying code in sendcmd_withirq_core()
cciss: factor out fix target status processing code from sendcmd functions
cciss: simplify interface of sendcmd() and sendcmd_withirq()
cciss: factor out core of sendcmd_withirq() for use by SCSI error handling code
cciss: Use schedule_timeout_uninterruptible in SCSI error handling code
block: needs to set the residual length of a bidi request
Revert "block: implement blkdev_readpages"
block: Fix bounce limit setting in DM
Removed reference to non-existing file Documentation/PCI/PCI-DMA-mapping.txt
...
Manually fix conflicts with tracing updates in:
block/blk-sysfs.c
drivers/ide/ide-atapi.c
drivers/ide/ide-cd.c
drivers/ide/ide-floppy.c
drivers/ide/ide-tape.c
include/trace/events/block.h
kernel/trace/blktrace.c
Linus Torvalds