CM REQs cannot be successfully retried, because a new pv_cm_id is
created for each request, without checking if one already exists.
By checking if an id exists before creating one, the bug is fixed.
This bug can be provoked by running an RDMA CM user-land application,
but inserting a five seconds delay before the rdma_accept() call on
the passive side. This delay is larger than the default CMA timeout,
and triggers a retry from the active side. The retried REQ will use
another pv_cm_id (the cm_id on the wire). This confuses the CM
protocol and two REJs are sent from the passive side.
Here is an excerpt from ibdump running without the patch:
3.285092 LID: 4 -> LID: 4 SDP 290 CM: ConnectRequest(SDP Hello)
7.382711 LID: 4 -> LID: 4 SDP 290 CM: ConnectRequest(SDP Hello)
7.382861 LID: 4 -> LID: 4 InfiniBand 290 CM: ConnectReject
7.387644 LID: 4 -> LID: 4 InfiniBand 290 CM: ConnectReject
and here is the same with bug fix applied:
3.251010 LID: 4 -> LID: 4 SDP 290 CM: ConnectRequest(SDP Hello)
7.349387 LID: 4 -> LID: 4 SDP 290 CM: ConnectRequest(SDP Hello)
8.258443 LID: 4 -> LID: 4 SDP 290 CM: ConnectReply(SDP Hello)
8.259890 LID: 4 -> LID: 4 InfiniBand 290 CM: ReadyToUse
Suggested-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Reported-by: Wei Lin Guay <wei.lin.guay@oracle.com>
Tested-by: Wei Lin Guay <wei.lin.guay@oracle.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Current computation of qp->timeout_jiffies in rvt_modify_qp() will cause
overflow due to the fact that the input to the function usecs_to_jiffies
is only 32-bit ( unsigned int). Overflow will occur when attr->timeout is
equal to or greater than 30. The consequence is unnecessarily excessive
retry and thus degradation of the system performance.
This patch fixes the problem by limiting the input to 5-bit and calling
usecs_to_jiffies() before multiplying the scaling factor.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Local ack delay exposed by the driver is 0 which means infinite QP
timeout. Reporting the default value to 16 (approx 260ms)
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
While invoking the req_notify_cq hook, ULPs can request
whether the CQs have any CQEs pending. If CQEs are pending,
drivers can indicate it by returning 1 for req_notify_cq.
The stack will poll CQ again till CQ is empty.
This patch peeks the CQ for any valid entries and return accordingly.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix the incorrect reporting of number of polled
entries by taking into account the max CQ depth
in the driver.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Driver shall check if the host system bios has enabled
Atomic operations capability in PCI Device Control 2
register of the pci-device. Expose the ATOMIC_HCA
flag only if the Atomic operations capability is set.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Starting FW version 20.6.47, firmware is keeping separate statistics
for L2 and RDMA. However, driver needs to specify RDMA or not when
allocating stat_ctx.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There's a couple of bugs in the support of max_rd_atomic and
max_dest_rd_atomic. In the modify_qp, if the requested max_rd_atomic,
which is the ORRQ size, is greater than what the chip can support,
then we have to cap the request to chip max as we can't have the HW
overflow the ORRQ. Capping the max_rd_atomic support internally is okay
to do as the remaining read/atomic WRs will still be sitting in the SQ.
However, for the max_dest_rd_atomic, the driver has to error out as
this dictates the IRRQ size and we can't control what the remote
side sends.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
- Report supported value for max_mr_size to IB stack in query_device.
Also, check and log if MR size requested by application in
reg_user_mr() is greater than value currently supported by driver.
- Report only 4K page size support for now
- Fix Max_QP value returned by ibv_devinfo -vv.
In case of PF, FW reserves 129 QPs for creating QP1s of VFs
and PF. So the max_qp value reported by FW for PF doesn'tt include
the QP1. Fixing this issue by adding 1 with the value reported
by FW.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This fix is added only to avoid system crash in some a
specific scenario. When bnxt_re driver is loaded and if
user tries to change interface mac address, delete GID
fails because QP1 is still associated with existing MAC
(default GID). If the above command fails GID tables are
not modified in the h/w or driver, but the GID context memory
is freed. Now, if the user changes the mac back to the original
value, another add_gid comes to the driver where the driver
reports that the GID is already present in its table
and tries to access the context which was already freed.
So, in this case, in order to avoid NULL pointer de-reference,
this patch removes the context memory free if delete_gid fails
and the same context memory is re-used in new add_gid.
Memory cleanup will be taken care during driver unload, while
deleting the GID table.
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Posting WQE size of 2 results in a WQE_FORMAT_ERROR
thrown by the HW as it requires host to supply WQE Size with room
for atleast one SGE so that the resulting WQE size be atleast 3.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The driver must free the DPI during the dealloc_ucontext
instead of freeing it during dealloc_pd. However, the DPI
allocation scheme remains unchanged.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
"umem" is a valid pointer. We intended to print "*umem" or even just
"err" instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If either of these allocations fail then we return ERR_PTR(0). That's
equivalent to NULL and results in a NULL pointer dereference in the
caller.
Fixes: fe2caefcdf ("RDMA/ocrdma: Add driver for Emulex OneConnect IBoE RDMA adapter")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We should preserve the original "status" error code instead of resetting
it to zero. Returning ERR_PTR(0) is the same as NULL and results in a
NULL dereference in the callers. I added a printk() on error instead.
Fixes: 45e86b33ec ("RDMA/ocrdma: Cache recv DB until QP moved to RTR")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We accidentally don't set the error code on some error paths. It means
return ERR_PTR(0) which is NULL and results in a NULL dereference in the
caller.
Fixes: 13a239330a ("RDMA/cxgb3: Don't ignore insert_handle() failures")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If one of these kmalloc() calls fails then we return ERR_PTR(0) which is
NULL. It results in a NULL dereference in the callers.
Fixes: cfdda9d764 ("RDMA/cxgb4: Add driver for Chelsio T4 RNIC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We accidentally forgot to set the error code if ib_copy_from_udata()
fails. It means we return ERR_PTR(0) which is NULL and results in a
NULL dereference in the callers.
Fixes: d374984179 ("i40iw: add files for iwarp interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We accidentally don't see the error code on some of these error paths.
It means we return ERR_PTR(0) which is NULL and it results in a NULL
dereference in the caller.
This bug dates to pre-git days.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If the physical buffer list entries (PBLEs) of a QP are freed
up at i40iw_dereg_mr, they can be assigned to a newly
created QP before the previous QP is destroyed. Fix this
by freeing PBLEs only when the QP is destroyed.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Control Queue Pair (CQP) request objects, which have
not received a completion upon interface close, remain
in memory.
To fix this, identify and free all pending CQP request
objects during destroy CQP OP.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
To avoid infinite loop, in i40iw_ieq_handle_exception, update
plist inside while loop.
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add missing write memory barrier before writing the
header containing valid bit to the WQE in i40iw_puda_send.
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Current flow leaves software QP structures in memory if
Control Queue Pair (CQP) destroy QP OP fails. To fix this,
free QP resources on fail of CQP destroy QP OP.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
On PCI function reset, cm_id reference is not released
which causes an application hang, as it waits on the
cm_id to be released on rdma_destroy.
To fix this, call i40iw_cm_disconn during a PCI function
reset to clean-up resources and release cm_id reference.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Utilize iwdev->reset on a PCI function reset notification
instead of passing in reset flag for resource clean-up.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Control Queue Pair (CQP) OPs, in this case - Update SDs,
cannot poll the Control Completion Queue (CCQ) after CCQ is
destroyed. Instead, poll via registers.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The order for calling i40iw_destroy_pble_pool is incorrect.
Also, add PBLE_CHUNK_MEM init state to track pble pool
creation and destruction.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If the SynIC timer message delivery fails due to SINT message slot being
busy, there's no point to attempt starting the timer again until we're
notified of the slot being released by the guest (via EOM or EOI).
Even worse, when a oneshot timer fails to deliver its message, its
re-arming with an expiration time in the past leads to immediate retry
of the delivery, and so on, without ever letting the guest vcpu to run
and release the slot, which results in a livelock.
To avoid that, only start the timer when there's no timer message
pending delivery. When there is, meaning the slot is busy, the
processing will be restarted upon notification from the guest that the
slot is released.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
This can be reproduced by EPT=1, unrestricted_guest=N, emulate_invalid_state=Y
or EPT=0, the trace of kvm-unit-tests/taskswitch2.flat is like below, it tries
to emulate invalid guest state task-switch:
kvm_exit: reason TASK_SWITCH rip 0x0 info 40000058 0
kvm_emulate_insn: 42000:0:0f 0b (0x2)
kvm_emulate_insn: 42000:0:0f 0b (0x2) failed
kvm_inj_exception: #UD (0x0)
kvm_entry: vcpu 0
kvm_exit: reason TASK_SWITCH rip 0x0 info 40000058 0
kvm_emulate_insn: 42000:0:0f 0b (0x2)
kvm_emulate_insn: 42000:0:0f 0b (0x2) failed
kvm_inj_exception: #UD (0x0)
......................
It appears that the task-switch emulation updates rflags (and vm86
flag) only after the segments are loaded, causing vmx->emulation_required
to be set, when in fact invalid guest state emulation is not needed.
This patch fixes it by updating vmx->emulation_required after the
rflags (and vm86 flag) is updated in task-switch emulation.
Thanks Radim for moving the update to vmx__set_flags and adding Paolo's
suggestion for the check.
Suggested-by: Nadav Amit <nadav.amit@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
The NVME standard mandates that the SN, MN, and FR fields of the Identify
Controller Data Structure be "ASCII strings". That means that they may
not contain 0-bytes, not even string terminators.
Signed-off-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
[hch: fixed for the move of the serial field, updated description]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The NVMe target has no way to preserve controller serial
IDs across reboots which breaks udev scripts doing
SYMLINK+="dev/disk/by-id/nvme-$env{ID_SERIAL}-part%n.
Export the randomly generated serial number via configfs and allow
setting of a serial via configfs to mitigate this breakage.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The NVMe specification defines the serial number as:
"Serial Number (SN): Contains the serial number for the NVM subsystem
that is assigned by the vendor as an ASCII string. Refer to section
7.10 for unique identifier requirements. Refer to section 1.5 for ASCII
string requirements"
So move it from the controller to the subsystem, where it belongs.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The NVMe target's attribute files need an attr prefix in order to have
nvmetcli recognize them. Add this attribute.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Release resources in the correct order in order not to miss a
'put_device()' if 'nvme_dev_map()' fails.
Fixes: b00a726a9f ("NVMe: Don't unmap controller registers on reset")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch replaces the invalid nvme SGL kernel panic with a warning,
and returns an appropriate error. The warning will occur only on the
first occurance, and sgl details will be printed to help debug how the
request was allowed to form.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Adds a fourth Intel controller which has the "stripe" quirk.
Signed-off-by: David Wayne Fugate <david.fugate@intel.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We always need to do non-equal comparisms on the native endian versions
to get the correct result.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Check return value from call to devm_kmemdup() in order to prevent a NULL
pointer dereference.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The variables which are processed by RCU functions should be annotated
as RCU, otherwise sparse will report the errors like below:
"error: incompatible types in comparison expression (different
address spaces)"
Link: http://lkml.kernel.org/r/1496823171-7758-1-git-send-email-zhang.chunyan@linaro.org
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
[ Updated to not be 100% 80 column strict ]
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Hit the kmemleak when executing instance_rmdir, it forgot releasing
mem of tracing_cpumask. With this fix, the warn does not appear any
more.
unreferenced object 0xffff93a8dfaa7c18 (size 8):
comm "mkdir", pid 1436, jiffies 4294763622 (age 9134.308s)
hex dump (first 8 bytes):
ff ff ff ff ff ff ff ff ........
backtrace:
[<ffffffff88b6567a>] kmemleak_alloc+0x4a/0xa0
[<ffffffff8861ea41>] __kmalloc_node+0xf1/0x280
[<ffffffff88b505d3>] alloc_cpumask_var_node+0x23/0x30
[<ffffffff88b5060e>] alloc_cpumask_var+0xe/0x10
[<ffffffff88571ab0>] instance_mkdir+0x90/0x240
[<ffffffff886e5100>] tracefs_syscall_mkdir+0x40/0x70
[<ffffffff886565c9>] vfs_mkdir+0x109/0x1b0
[<ffffffff8865b1d0>] SyS_mkdir+0xd0/0x100
[<ffffffff88403857>] do_syscall_64+0x67/0x150
[<ffffffff88b710e7>] return_from_SYSCALL_64+0x0/0x6a
[<ffffffffffffffff>] 0xffffffffffffffff
Link: http://lkml.kernel.org/r/1500546969-12594-1-git-send-email-chuhu@redhat.com
Cc: stable@vger.kernel.org
Fixes: ccfe9e42e4 ("tracing: Make tracing_cpumask available for all instances")
Signed-off-by: Chunyu Hu <chuhu@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Both xhci_hub_control and xhci_disable_slot tries to hold spinlock, the
spinlock recursion occurs when enters USB2 test mode. Fix it by unlock
spinlock before calling xhci_disable_slot.
Cc: <stable@vger.kernel.org>
Fixes: 0f1d832ed1 ("usb: xhci: Add port test modes support for usb2")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A uncleared PLC (port link change) bit will prevent furuther port event
interrupts for that port. Leaving it uncleared caused get_port_status()
to timeout after 20000ms while waiting to get the final port event
interrupt for resume -> U0 state change.
This is a targeted fix for a specific case where we get a port resume event
racing with xhci resume. The port event interrupt handler notices xHC is
not yet running and bails out early, leaving PLC uncleared.
The whole xhci port resuming needs more attention, but while working on it
it anyways makes sense to always ensure PLC is cleared in get_port_status
before setting a new link state and waiting for its completion.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
on AMD platforms with SNPS 3.1 USB controller if stop endpoint command is
issued the controller does not respond, when the EP is not in running
state. HW completes the command execution and reports
"Context State Error" completion code. This is as per the spec. However
HW on receiving the second command additionally marks EP to Flow control
state in HW which is RTL bug. This bug causes the HW not to respond
to any further doorbells that are rung by the driver. This makes the EP
to not functional anymore and causes gross functional failures.
As a workaround, not to hit this problem, it's better to check the EP state
and issue a stop EP command only when the EP is in running state.
As a sidenote, even with this patch there is still a possibility of
triggering the RTL bug if the context state races with the stop endpoint
command as described in xHCI spec 4.6.9
[code simplification and reworded sidenote in commit message -Mathias]
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When USB Ethernet is plugged in ASMEDIA ASM1042A xHCI host, bad
performance was manifesting in Web browser use (like download
large file such as ISO image). It is known limitation of
ASM1042A that is not compatible with driver scheduling,
As a workaround we can modify flow control handling of ASM1042A.
The register we modify is changes the behavior
[use quirk bit 28, usleep_range 40-60us, empty non-pci function -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Jiahau Chang <Lars_chang@asmedia.com.tw>
Signed-off-by: Ian Pilcher <arequipeno@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This off by one in stream_id indexing caused NULL pointer dereference and
soft lockup on machines with USB attached SCSI devices connected to a
hotpluggable xhci controller.
The code that cleans up pending URBs for dead hosts tried to dereference
a stream ring at the invalid stream_id 0.
ep->stream_info->stream_rings[0] doesn't point to a ring.
Start looping stream_id from 1 like in all the other places in the driver,
and check that the ring exists before trying to kill URBs on it.
Reported-by: rocko r <rockorequin@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Håkon Bugge