This moves the mcp23s08 driver from gpio to pinctrl. Actual
pinctrl support for configuration of the pull-up resistors
follows in its own patch.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The header file is used by the SPI and I2C variant of the driver.
Therefore, move it to a more generic place under platform_data.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Changed bfin_get_ether_addr() to return a state and to
set no random mac address if the board don't provide one.
Let the caller of bfin_get_ether_addr() set a random mac
address if the return value is not 0.
v2: don't set random mac in bfin_get_ether_addr()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macro name for spi controller driver has been modified, so update default
board file accordingly.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
The serial TX IRQ is not simply (RX IRQ + 1) on some Blackfin chips,
so move the values to the platform resources.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
These particular files were just assuming that module.h was
somehow in the include paths. Give them the more minimalist
header file explicitly.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The default for the Blackfin SPI driver is 8 bits and dma disabled,
so many of the bfin5xx_spi_chip resources are redundant. So punt
those parts.
Further, drivers should themselves be declaring 16 bit transfers,
so for those that do, and for the ones which no longer do 16 bit
transfers, drop the bfin5xx_spi_chip resources.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The SPORT/UART driver doesn't use the secondary channel pins, so don't
try and request them thus keeping other drivers from using them.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
platfrom -> platform
This changes a struct name. The related code is conditionally
compiled and won't work because the include file linux/gpio-decoder.h
is missing, so removing this code would be an even better solution.
If the missing include file is added, it must fix the spelling, too.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Just adding its own platform_driver, not really
using it yet.
Later patches will come to split power management
code from musb_core and move it completely to HW
glue layer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
change all ocurrences of musb_hdrc to musb-hdrc.
We will call glue layer drivers musb-<glue layer>,
so in order to keep things somewhat standard, let's
change the underscore into a dash.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move all the pin settings out of the Kconfig and into the platform
resources (MII vs RMII). This clean up also lets us push out the
phy settings so that board porters may control the layout.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Sebastian Reichel