Remove the control.sta pointer from ieee80211_tx_info to free up
sufficient space in the TX skb control buffer for the upcoming
Transmit Power Control (TPC).
Instead, the pointer is now on the stack in a new control struct
that is passed as a function parameter to the drivers' tx method.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[reworded commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using work_pending() to defer certain operations when
a HW-reset work has been queued is racy since the check
would return false when the work item is actually in
execution. Use SC_OP_HW_RESET instead to fix this race.
Also, unify the reset debug statistics maintenance.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an interface in AP or P2P-GO mode is removed,
check whether a station interface is already present and
reconfigure the beacon timers etc. properly if it's
associated.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, there are problems with how ANI is handled in
multi-VIF scenarios. This patch addresses them by unifying
the start/stop logic.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused variables, use a helper function to choose
the slot and reset beaconing status at one place.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setup the beacon queue parameters after disabling
interrupts. Also, remove the redundant call in conf_tx()
for IBSS mode since the queue would be configured
with the appropriate cwmin/cwmax values when beaconing
is enabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the tx_last_beacon() callback, mac80211's beaconing
status can be used instead. The beacon tasklet doesn't require
it because it is disabled when removing a slot.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* The beaconing status routine is not required, since in
multi-VIF cases the HW beacon parameters should not be
re-configured.
* Remove SC_OP_TSF_RESET - when a beaconing interface comes
up the first time, the TSF has to be reset.
* Simplify ath9k_allow_beacon_config().
* Handle setting/clearing the SWBA interrupt properly.
* Remove the TSF mangling in IBSS mode, it is not required.
* General code cleanup.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cleanup the messy logic dealing with station association
and disassociation.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Do not set/clear TSF when adding/deleting an interface.
This should be done when the BSS is set up and should also
take into account the existence of other interfaces.
* Set opmode explicitly.
* ANI setup needs to be decided based on multiple interfaces.
This can be done via the bss_info_changed() callback.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch revamps interface addition and deletion and simplifies
slot allocation. There is no need to setup the beacon buffer
in add/remove interface, remove this and use simple APIs for
assigning/deleting slots.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9485, AR9330 and AR9340 are the chips that this is *NOT* supposed to be
applied on.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- add an inline function for getting the correct modal EEPROM struct
- remove unnecessary indirection through ath9k_hw_ar9300_get_eeprom
access the relevant fields directly
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the aggregate size exceeds the TXOP limit, it leads to lots of unnecessary
hardware and software retries.
The previous 4ms frame limit table was completely undocumented, the commit
that updated it only vaguely referenced and equation from the standard,
but I've been unable to replicate its results.
Fix this by using a formula based on the code in ath_pkt_duration, which is
more likely to be correct for this case.
Reported-by: Dave Täht <dave.taht@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prepare for using different queue size defaults for each AC.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In all those years apparently nobody noticed that the txop limit programmed
into the chip was off by a factor of 32 (!), probably because the VI and VO
queues aren't used that much aside from mgmt frames on VO.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The row/column sizes can be derived from the array argument within the macro
itself, which is less error prone. In a few cases the supplied column size
was actually wrong.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the EEPROM information to choose the right tx gain table
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many chips are not able to deal with non-consecutive rx antenna selections
and respond with calibration errors, reset errors, etc.
When an antenna is selected as a tx antenna, also flag it for rx to avoid
chip issues.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old code was an accidental copy&paste of the 2.4 GHz version,
which doesn't work.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Turns out every most standard Linux distributions enable
CONFIG_EXPERT, so use the shiny new CFG80211_CERTIFICATION_ONUS
which is meant by design to not be enabled by all Linux
distributions.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware needs to be AWAKE and should maintain association
with the AP to process WoW triggers any time
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add suspend/resume/set_wakeup callbacks to the driver
*suspend
- bail out only if all the conditions for configuring WoW.
is fine, currently multivif case is not handled
- check for associated state.
- map wow triggers from user space data.
- add deauth/disassoc pattern and user defined pattern,
for the later a list is maintained.
- store the interrupt mask before suspend, enabled beacon
miss interrupt for WoW.
- configure WoW in the hardware by calling ath9k_hw_wow_enable.
*resume
- restore the interrupts based on the interrupt mask
stored before suspend.
- call ath9k_hw_wow_wakeup to configure/restore the hardware.
- after wow wakeup clear away WoW events and query the
WoW wakeup reason from the status register
*set_wakeup
- to call 'device_set_wakeup_enable' from cfg80211/mac80211
when wow is configured and as per Rafael/Johannnes the
right way to do so rather in the driver suspend/resume
call back
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add a new file wow.c which takes care of the hardware code
for WoW.
*program the descriptors and data words to periodically
send Keep Alive Frames.
*program the user defined patterns/masks and pattern length
in the hardware registers.
*'ath9k_hw_wow_enable' is called during the drivers suspend
callback which takes care of the following
- tracking wow event mask (to suppress spurious
wow events)
- properly configure suspend/resume WAR registers
- configure PCIE PM control register
- configure MAC WoW registers and their timeouts
- enabling wow configuration like magic packet,
user patterns based on users configuration
- configuring timeouts for KAL, beacon miss,
aifs, slot time, backoff
- create Keep Alive Pattern ('KAL')
*'ath9k_hw_wow_wakeup' is called during the drivers resume
callback which takes care of the following
- primary task is to find the reason for wakeup
from the wow status register
- configure/restore AR_PCIE_PM_CTRL register
- clear all WoW events
- configure/restore suspend/resume WAR registers
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
for AR9002 family of chipsets and for WoW sleep, we reprogram
the SerDes so that the PLL and CHK REQ are both enabled. this
uses more power but in certain cases this is required as otherwise
WoW sleep is unstable and chip may disappear.
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
currently the code supports WoW triggers due to
*magic packet
*user defined patterns
*deauth and disassoc patterns
*disconnect - beacon miss, last beacon received timeout,
no ack for keeep alive frames.
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
support WoW for all chipsets starting from AR9280, AR9285, AR9287,
AR9380, AR9382, AR9485, AR9462. Really all hardware may not support
WoW even though the flag is set and the WoW working depends on
your laptop, BIOS apart from the hardware.
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
have seperate wow capability flags for
*basic wow support
*device capable of matching exact user defined pattern
or de-authentication/disassoc pattern
*device such AR9280 requires first four bytes for
all sort of patterns
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
*add structures, macros and variables for WoW, so that the driver
can make use of it.
*maintain a list for user enabled patterns and masks
*track pattern slots for the hardware limitation on the
maximum number of patterns that can be stored.
*track interrupts enabled before WoW suspend, so
that can be reconfigured after resume
*have macros to parse user defined wow configurations to
hardware code
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the CONT_* and LNA_* messages from
AR_MCI_INTERRUPT_RX_MSG_DEFAULT. Those MCI rx messages only
meant for debugging purpose. Including them in default rx_msg
series could raise huge amount of MCI interrupts when BT traffic
is going on. And also it increases power consumption when WLAN
is scanning.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Its safe to stop the BTCOEX timers 'period_timer' and
'no_stomp_timer' before disabling BTCOEX. These timers
can call ath9k_hw_btcoex_enable (or) change the BT
stomp type if they seem to be running after we had
called ath9k_hw_btcoex_disable, which is obviously
not correct.
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are doing MCI cleanup eventhough BTCOEX is not enabled
via module parameter. This means we do ath_mci_cleanup
though we skipped calling ath_mci_setup. Yet it does not
causes any issues now as we free the DMA buffer allocated
only when it is allocated during ath_mci_setup.
Reviewed-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On full reset, mci reset will put LNA update on 2G mode. And
Whenever 2g5g_switch is forced at the end of full reset, lna
update should not be skipped. Not doing so, is affecting WLAN
rx and causing beacon loss when BTCOEX is enabled on AR9462.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chip is waken up for every 45ms in btcoex timer cycle to
for sharing the radio between BT and WLAN. Whenever the wlan
interface is in network sleep mode, do not schedule hw timers.
This could reduce power consumption on idle associated state.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As soon as the interface brought up, btcoex timer starts running
eventhough the interface is in idle state and WLAN chip is moved
to full sleep mode. There is no point in running btcoex timer when
the wlan interface is in sleep mode and also it might consumes
more power on WLAN idle unassociated state. So lets stop the
btcoex when wlan is idle state.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Noise floor calibration is performed on longcal interval and
the reading will be updated in history buffer. On rare occasions,
the previous noisefloor calibration might not be completed within
the period and trying to load nf reading will be failed. In such
situation, postpone the nf cabliration to next cycle to give
enough time to complete the calibration. This was already taken
care for ar9002 chips.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
noisefloor calibration has to be loaded and started after
chip reset completion and restoring chainmask. Right now it is
being started before MCI reset completion on full reset. Fix that.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some register values of bit shifts are corrected in order to support the upcoming
transmission power control (tpc) for control packets as well.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BTCOEX flags are set/cleared by atomic operations.
We got to do the same in ath9k_btcoex_timer_resume,
while clearing those BTCOEX flags.
Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/caif/caif_hsi.c
drivers/net/usb/qmi_wwan.c
The qmi_wwan merge was trivial.
The caif_hsi.c, on the other hand, was not. It's a conflict between
1c385f1fdf ("caif-hsi: Replace platform
device with ops structure.") in the net-next tree and commit
39abbaef19 ("caif-hsi: Postpone init of
HIS until open()") in the net tree.
I did my best with that one and will ask Sjur to check it out.
Signed-off-by: David S. Miller <davem@davemloft.net>
The initvals tool from https://github.com/mcgrof/qca-swiss-army-knife has
been modified to detect identical initval tables and replace them with
macros. This patch contains the generated changes.
On MIPS this reduces the binary size by 24 KB with no runtime changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Generated using the initvals tool from the qca-swiss-army-knife repository
from https://github.com/mcgrof/qca-swiss-army-knife
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
seems i got a message like this
ath: phy0: BT_Status_Update: is_link=0, linkId=2,
state=1, SEQ=-2085766476 initially.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_mci_is_enabled wrapper also takes care of
ATH9K_HW_CAP_MCI being set for the AR9462 under test.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_ani_reset (which is called at reset time) uses a state variable
ani->update_ani to prevent the ANI noise immunity state on the operating
channel from being overwritten by background scans. Unfortunately this
is also being set for AP mode, since it's mixed with code that is only
supposed to change the default settings after a reset.
In AP mode this has the side effect of having ANI run, but being unable to
change its runtime noise immunity level, making it effectively useless.
Fix this by getting rid of ani->update_ani and passing a parameter to
ath9k_hw_set_ofdm_nil and ath9k_hw_set_cck_nil instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wrap the MCI-work canceling with CONFIG_ATH9K_BTCOEX_SUPPORT.
Reported-by: Emmanuel Benisty <benisty.e@gmail.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 3a2923e83c introduced a bug when a corrupt descriptor
is encountered - although the following descriptor is discarded
and returned to the queue for reuse the associated frame is
also returned for processing. This leads to a panic:
BUG: unable to handle kernel NULL pointer dereference at 000000000000003a
IP: [<ffffffffa02599a5>] ath_rx_tasklet+0x165/0x1b00 [ath9k]
Call Trace:
<IRQ>
[<ffffffff812d7fa0>] ? map_single+0x60/0x60
[<ffffffffa028f044>] ? ath9k_ioread32+0x34/0x90 [ath9k]
[<ffffffffa0292eec>] athk9k_tasklet+0xdc/0x160 [ath9k]
[<ffffffff8105e133>] tasklet_action+0x63/0xd0
[<ffffffff8105dbc0>] __do_softirq+0xc0/0x1e0
[<ffffffff8101a873>] ? native_sched_clock+0x13/0x80
[<ffffffff815f9d5c>] call_softirq+0x1c/0x30
[<ffffffff810151f5>] do_softirq+0x75/0xb0
[<ffffffff8105df95>] irq_exit+0xb5/0xc0
[<ffffffff815fa5b3>] do_IRQ+0x63/0xe0
[<ffffffff815f0cea>] common_interrupt+0x6a/0x6a
<EOI>
[<ffffffff8131840a>] ? intel_idle+0xea/0x150
[<ffffffff813183eb>] ? intel_idle+0xcb/0x150
[<ffffffff814a1db9>] cpuidle_enter+0x19/0x20
[<ffffffff814a23d9>] cpuidle_idle_call+0xa9/0x240
[<ffffffff8101c4bf>] cpu_idle+0xaf/0x120
[<ffffffff815cda8e>] rest_init+0x72/0x74
[<ffffffff81cf4c1a>] start_kernel+0x3b7/0x3c4
[<ffffffff81cf4662>] ? repair_env_string+0x5e/0x5e
[<ffffffff81cf4346>] x86_64_start_reservations+0x131/0x135
[<ffffffff81cf444a>] x86_64_start_kernel+0x100/0x10f
Making sure bf is cleared to NULL in this case restores the
old behaviour.
Signed-off-by: Tom Hughes <tom@compton.nu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the radio enable/disable stuff and fix the
transition to FULL_SLEEP mode when the device is idle.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 adds stations in HT IBSS as soon as a frame comes by,
even if the HT capabilities are not known yet (they are often
received later, e.g. in beacons). So far, ampdu factor/density
are only calculated when the station is initially added.
This patch changes this to update ampdu factor/density settings
when starting a blockack session.
Using this patch, we had performance boosts from 60 to 150 MBit/s
between two 2x2 Atheros devices in 5 GHz HT IBSS mode.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/usb/qmi_wwan.c
net/batman-adv/translation-table.c
net/ipv6/route.c
qmi_wwan.c resolution provided by Bjørn Mork.
batman-adv conflict is dealing merely with the changes
of global function names to have a proper subsystem
prefix.
ipv6's route.c conflict is merely two side-by-side additions
of network namespace methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 7a532fe713
ath9k_hw: fix interpretation of the rx KeyMiss flag
This commit used the rx key miss indication to detect packets that were
passed from the hardware without being decrypted, however it seems that
this bit is not only undefined in the static WEP case, but also for
dynamically allocated WEP keys. This caused a regression when using
WEP-LEAP.
This patch fixes the regression by keeping track of which key indexes
refer to CCMP keys and only using the key miss indication for those.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename mrcCCKOff for better code readability and also fixes
the smatch warning.
drivers/net/wireless/ath/ath9k/ar9003_phy.c:982
ar9003_hw_ani_control() Error invalid range 1 to 0.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The baseband and cycle counters are being sampled during ani
processing for debugging purpose. Whenever the ani is postponded
due to sleep state, taking samples on that time is of no use and
also unneccesarily waking up the chip might increase the power
consumption on idle associated state. Hence moving debug function
within powersave block.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When WLAN enter full sleep mode, WLAN HW should send out a LNA_TAKE
message for BT to take control of the shared LNA. Otherwise BT traffic
is completely stopped whenever the wlan interface is moved full sleep
mode.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During driver stop, btcoex is disabled and also btcoex_hw.enabled
is set to false. Afterwards mci_is_enabled returns false so that
BT is not gaining SPDT control on WLAN sleep. Fix that.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WLAN driver initialization is muting BT which is terminating
the ongoing BT traffic. The reason to mute BT is to avoid any
incoming MCI messages from BT when MCI reset is in progress that
could corrupt WLAN MCI RX state machine. But we should not
dedicate radio completely to WLAN in driver init itself. So this
patch removes the wlan weightage changes from mute BT to retain
BT connection.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Two MCI interrupts are generated while adding A2DP and headset profiles
with different types and same connection handle. While disconnecting,
only one MCI interrupt is generated with last added profile type value
for both profiles.
While adding second profile type decrement first one.
Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adjust ah->config.ofdm_trig_{high,low} when setting noise immunity values
to simplify threshold checks in ath9k_hw_ani_monitor
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit af1e8a6f "ath9k: reset noiseimmunity level to default" was supposed
to ensure that the default noise immunity level is above the INI
values, however it prevents setting lower noise immunity values altogether.
Fix this by moving the checks to the right function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was found to be buggy on a variety of chipsets from AR913x to AR928x.
The new version (which was introduced along with AR93xx support) is more
reliable in preventing connectivity dropouts and also fixes MIB interrupt
storm issues.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacon RSSI is only meaningful in station mode - in ad-hoc mode it
fluctuates, depending on which peer last sent a beacon, and in other
modes it is not set at all.
Fix places in ANI where the beacon RSSI is used to limit their use
to station mode only.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Code using this had already triggered smatch complaints, so remove it before
it gets fixed the wrong way.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "ath9k_hw: improve ANI processing and rx desensitizing parameters"
was unifying some code related to overriding OFDM weak signal detection,
but seems to have gotten some of the original intent wrong, probably
because of a misnamed variable.
The beacon RSSI is only valid in station mode, and the main reason to check
it in ath9k_hw_set_ofdm_nil is to make sure that OFDM weak signal detection
stays enabled if the RSSI is low, even when the OFDM noise immunity entry
is supposed to disable it.
The above commit removed the mode checks and changed the code so that
OFDM weak signal detection would only be changed if the rssi is high, which
is wrong for everything but client mode.
This patch restores the old behavior in a simplified form.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I don't know why somebody decided to keep a cached copy of beacon rssi in a
variable called 'noiseFloor', but the caching is unnecessary and the variable
name is confusing, so let's just get rid of it entirely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the change "mac80211: remove spurious BSSID change flag",
BSS_CHANGED_BSSID will not be passed on association or IBSS
status changes. So it could be better to program bssid on ASSOC
or IBSS change notification. Not doing so, is affecting the
packet transmission.
Cc: stable@vger.kernel.org [3.4+]
Reported-by: Michael Leun <lkml20120218@newton.leun.net>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"ath9k: Fix softlockup in AR9485" with commit id
64bc1239c7 fixed the reported
issue, yet its better to avoid the possible infinite loop
in ar9003_get_pll_sqsum_dvc by having a timeout as suggested
by ath9k maintainers.
http://www.spinics.net/lists/linux-wireless/msg92126.html.
Based on my testing PLL's locking measurement is done in
~200us (2 iterations).
Cc: stable@vger.kernel.org
Cc: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After setup_frame_info has been called, only info->control.rates is still
valid, other control fields have been overwritten by the ath_frame_info
data. Move the access to info->control.vif for checking short preamble
to setup_frame_info before it gets overwritten.
This regression was introduced in commit d47a61aa
"ath9k: Fix multi-VIF BSS handling"
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Thomas Hühn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: stable@vger.kernel.org [3.4]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rate pointer variable for a rate series is used in a loop before it is
initialized. This went unnoticed because it was used earlier for the RTS/CTS
rate. This bug can lead to the wrong PHY type being passed to the
duration calculation function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
remove MCI_STATE_BT and use bt_state instead.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As p_data is unuse, lets remove it from ar9003_mci_state.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a MCI util function to send wlan channel info to BT.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a utility function to set bluetooth version and remove
MCI_STATE_SET_BT_COEX_VERSION.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add utility functions to get and test GPM offset and
remove MCI_STATE*_GPM_OFFSET states.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
steps to recreate:
load latest ath9k driver with AR9485
stop the network-manager and wpa_supplicant
bring the interface up
Call Trace:
[<ffffffffa0517490>] ? ath_hw_check+0xe0/0xe0 [ath9k]
[<ffffffff812cd1e8>] __const_udelay+0x28/0x30
[<ffffffffa03bae7a>] ar9003_get_pll_sqsum_dvc+0x4a/0x80 [ath9k_hw]
[<ffffffffa05174eb>] ath_hw_pll_work+0x5b/0xe0 [ath9k]
[<ffffffff810744fe>] process_one_work+0x11e/0x470
[<ffffffff8107530f>] worker_thread+0x15f/0x360
[<ffffffff810751b0>] ? manage_workers+0x230/0x230
[<ffffffff81079af3>] kthread+0x93/0xa0
[<ffffffff815fd3a4>] kernel_thread_helper+0x4/0x10
[<ffffffff81079a60>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff815fd3a0>] ? gs_change+0x13/0x13
ensure that the PLL-WAR for AR9485/AR9340 is executed only if the STA is
associated (or) IBSS/AP mode had started beaconing. Ideally this WAR
is needed to recover from some rare beacon stuck during stress testing.
Before the STA is associated/IBSS had started beaconing, PLL4(0x1618c)
always seem to have zero even though we had configured PLL3(0x16188) to
query about PLL's locking status. When we keep on polling infinitely PLL4's
8th bit(ie check for PLL locking measurements is done), machine hangs
due to softlockup.
fixes https://bugzilla.redhat.com/show_bug.cgi?id=811142
Reported-by: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: stable@vger.kernel.org
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Reset duty cycle before updating btcoex scheme. Otherwise duty cycle
reaches max limit and never be reduced again
* Adjust duty cycle with proper BDR profile value
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As btcoex scheme updation might sleep, remove the function call
from tasklet context and queue it up as a separate work.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
btcoex periord is converted into micro seconds during initialization
and converted back to milli seconds while starting timer. As MCI code
handles btcoex period in msec, lets keep the btcoex timer in msec and
convert them into other form whenever needed.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch simplifies profile management utility functions.
* Separate find_profile from add/del functions
* Return correct values when the profile list is empty or
profile is ot found
* flush the profiles when there are entries in the list
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
let us process MCI interrupts only when BTCOEX is enabled to avoid
processing bogus interrupts.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After a full reset, mci_reset will put LNA update to the setting
for 2G mode. Those registers need to be forced to update when
the channel is in 5G.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both "MAC Warm Reset" and "MCI Reset Rx" will reset GPM HW write_ptr.
We should check software cached write_ptr against HW write_ptr before
reset. Otherwise the pending DMA data will be lost.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW statemachine is sometimes found stuck in the state
WL_LNA_CTRL_DISABLE when BT is in sleep, which will cause
TX_HOLD always asserted and resmgr stuck in PENDING_TX state
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not doing so, could cause imbalance in powersave count.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Choose legacy rate as the last rate of Multi Rate Retry series
if and only if the last selected rate is MCS and having higher
PER rate. The current code fills a legacy rate as last one even
though the previous rates in the series are having good PER value.
This could limit the aggregation that affects the uplink performance.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adjust quick_drop value in the baseband AGC register to
improve RX in HT20 mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
steps to recreate:
load latest ath9k driver with AR9485
stop the network-manager and wpa_supplicant
bring the interface up
Call Trace:
[<ffffffffa0517490>] ? ath_hw_check+0xe0/0xe0 [ath9k]
[<ffffffff812cd1e8>] __const_udelay+0x28/0x30
[<ffffffffa03bae7a>] ar9003_get_pll_sqsum_dvc+0x4a/0x80 [ath9k_hw]
[<ffffffffa05174eb>] ath_hw_pll_work+0x5b/0xe0 [ath9k]
[<ffffffff810744fe>] process_one_work+0x11e/0x470
[<ffffffff8107530f>] worker_thread+0x15f/0x360
[<ffffffff810751b0>] ? manage_workers+0x230/0x230
[<ffffffff81079af3>] kthread+0x93/0xa0
[<ffffffff815fd3a4>] kernel_thread_helper+0x4/0x10
[<ffffffff81079a60>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff815fd3a0>] ? gs_change+0x13/0x13
ensure that the PLL-WAR for AR9485/AR9340 is executed only if the STA is
associated (or) IBSS/AP mode had started beaconing. Ideally this WAR
is needed to recover from some rare beacon stuck during stress testing.
Before the STA is associated/IBSS had started beaconing, PLL4(0x1618c)
always seem to have zero even though we had configured PLL3(0x16188) to
query about PLL's locking status. When we keep on polling infinitely PLL4's
8th bit(ie check for PLL locking measurements is done), machine hangs
due to softlockup.
fixes https://bugzilla.redhat.com/show_bug.cgi?id=811142
Reported-by: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: stable@vger.kernel.org [3.0+]
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MSI is enabled by default for most of the 4th generation
chips. Add this for AR9462 - this fixes PowerSave operation,
the chip was not entering Network-Sleep mode earlier.
With proper powering down of the MAC now, power consumption
in associated state is reduced considerably.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'cfg80211: fix interface combinations' ensures that if an interface
type is not advertised by the driver in any of the interface combinations
(via ieee80211_iface_combination) then it shall be treated as a single
incompatible interface. if there are more than one interfaces present
and changing them to incompatible interface type is not possible.
These checks will be properly handled by cfg80211_change_iface ->
cfg80211_can_change_interface.
this patch is dependent on 'cfg80211: fix interface combinations'
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this patch is dependent on the patch "cfg80211: fix interface
combinations"
In ath9k currently we have ADHOC interface as a single incompatible
interface. when drv_add_interface is called during resume we got to
consider number of vifs already present in addition to checking the
drivers 'opmode' information about ADHOC. we incorrectly assume
an ADHOC interface is already present. Then we may miss some driver
specific data for the ADHOC interface after resume.
The above mentioned checks can be removed from the driver,
as the patch 'cfg80211: fix interface combinations' ensures that
if an interface type is not advertised by the driver in any of the
interface combinations(via ieee80211_iface_combination) then it shall
be treated as a single incompatible interface. Fixes the following
warning on suspend/resume with ibss interface.
ath: phy0: Cannot create ADHOC interface when other
interfaces already exist.
WARNING: at net/mac80211/driver-ops.h:12
ieee80211_reconfig+0x1882/0x1ca0 [mac80211]()
Hardware name: 2842RK1
wlan2: Failed check-sdata-in-driver check, flags: 0x0
Call Trace:
[<c01361b2>] warn_slowpath_common+0x72/0xa0
[<f8aaa7c2>] ? ieee80211_reconfig+0x1882/0x1ca0
[mac80211]
[<f8aaa7c2>] ? ieee80211_reconfig+0x1882/0x1ca0
[mac80211]
[<c0136283>] warn_slowpath_fmt+0x33/0x40
[<f8aaa7c2>] ieee80211_reconfig+0x1882/0x1ca0 [mac80211]
[<c06c1d1a>] ? mutex_lock_nested+0x23a/0x2f0
[<f8a95097>] ieee80211_resume+0x27/0x70 [mac80211]
[<fd177edf>] wiphy_resume+0x8f/0xa0 [cfg80211]
Cc: stable@vger.kernel.org
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After a chip reset, the beacon timers have to re-programmed
correctly for a station in associated state. Use the PS flags
to ensure that this is done after a TSF sync happens, otherwise
the driver ends up using incorrect values for TBTT/DTIM in
powersave mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'ps_flags' is used/accessed in a variety of contexts
and requires proper locking. Use 'sc_pm_lock' appropriately.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a fatal interrupt is received or it is detected that the baseband
has hung, the chip has to be reset immediately. Otherwise, we end up
processing spurious interrupts. Ensure that we bail out properly in
the ISR when the reset work hasn't completed yet.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'sc_flags' variable is being used in a number of places
with no locking whatsoever. This patch converts the usage
of sc_flags to atomic ops.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And use a helper function to setup antennae after a reset.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Currently, there is no synchronization between the reset
work and the tx-poll work. Fix this and make sure that we
bail out properly if a reset work is in progress.
* Cleanup the PLL WAR and enable it for AR9340 too and
use a helper for restarting work/timers after a reset.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add link.c and move all the link/connection monitoring
code to it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When BT FTP/PAN transmits while WLAN is idle, the one of 9462 chain
often picks up BT's tx signal and starts receiving. If the current
weight is set to be higher than BT tx, BT tx will be aborted and this
also degrades BT performance. Hence lower WLAN rx priority in this
case only when there are no WLAN traffic.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Program MCI related power registers only if MCI interrupts
are enabled. This could help to reduce power consumptions when
WLAN alone is enabled in BT coex chips.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the chip is waking up from sleep state, the cycle counters
might have incorrect readings. So it is better not to update those
readings with software counters.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use smaller aggregation limit and increasing aggregation threshold
for osla that could improve wlan performance when there is HID profile.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When software rfkill is triggered, before put the chip in reset
state, give LNA and SPDT control to BT to make sure BT can have
good RF performance.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable WLAN and BT mode for switching regulator discontinuous
orverride for AR9462 chips.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
program BT to control SPDT everytime while loading switch table
from eeprom.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thomas Huehn