The analog audio setup consists of:
McASP3 <-> tlv320aic3104 codec
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DVDD is supplied via TPS77018DBVT fixed regulator from vdd_3v3
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The VBUS line of USB2 is connected to VBUS detect logic on
the PMIC. Use the palmas-usb driver to report VBUS events
to the USB driver.
As the palmas-usb driver supports GPIO based ID reporting
provide the GPIO for ID pin as well.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Originally, all the SoC PHY rails were supplied by LDO3. However, as a
result of characterization, it was determined that this posed a risk in
extreme load conditions. Hence the PHY rails are split between two
different LDOs. Update the related node as a result
LDO3/VDDA_1V8_PHYA supplies vdda_usb1, vdda_usb2, vdda_sata, vdda_usb3
LDO4/VDDA_1V8_PHYB supplies vdda_pcie1, vdda_pcie0, vdda_hdmi, vdda_pcie
NOTE: We break compatibility with pre-production boards with this change
since, the PMIC LDO4 is disabled at OTP level.
The new configuration is the plan of record and all pre-production
boards are supposed to be replaced with the latest boards matching the
mentioned configuration.
Some very few 10 something boards have been created and
stopped production till the latest modifications were done (PMIC USB
interrupt, LDO4 etc) - and all of those boards are now getting
scrapped.. If there are any (as per tracking information, there should
not be any), TI should be contacted to have them replaced.
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: updated commit about these being TI internal protos]
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the support in the generic PM framework for wakeirq and capability
added to the rtc-ds1307 driver to support this, we can now define the
optional wakeup irq to allow the RTC to wakeup the system from low power
modes as part of suspend.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For beagle x15, both the vdd and io lines are connected to the
same regulator (ldo1_reg). However vmmc_aux is populated to vdd_3v3.
Remove it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: updated to apply]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- Cleanups for Renesas shmobile platforms
- Lots of added devices on LPC18xx
- Lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some branches
that are primarily merged through the clock tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=D2Pm
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Ladies and gentlemen, we proudly announce to you the latest branch of
ARM device tree contents for the mainline kernel. Come and see, come
and see!
No less than twentythree thousand lines of additions! Just imagine the
joy you will have of using your mainline kernel on newly supported
hardware such as Rockchip Chromebooks, Freescale i.MX6UL boards or
UniPhier hardware!
For those of you feeling less adventurous, added hardware support on
platforms such as TI DM814x and Gumstix Overo platforms might be more
of your liking.
We've got something for everyone here!
Ahem. Cough. So, anyway...
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- cleanups for Renesas shmobile platforms
- lots of added devices on LPC18xx
- lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some
branches that are primarily merged through the clock tree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (389 commits)
ARM: tegra: Add gpio-ranges property
ARM: tegra: Fix AHB base address on Tegra20, Tegra30 and Tegra114
ARM: tegra: Add Tegra124 PMU support
ARM: tegra: jetson-tk1: Add GK20A GPU DT node
ARM: tegra: venice2: Add GK20A GPU DT node
ARM: tegra: Add IOMMU node to GK20A
ARM: tegra: Add CPU regulator to the Jetson TK1 device tree
ARM: tegra: Add entries for cpufreq on Tegra124
ARM: tegra: Enable the DFLL on the Jetson TK1
ARM: tegra: Add the DFLL to Tegra124 device tree
ARM: dts: zynq: Add devicetree entry for Xilinx Zynq reset controller.
ARM: dts: UniPhier: fix PPI interrupt CPU mask of timer nodes
ARM: dts: rockchip: correct regulator power states for suspend
ARM: dts: rockchip: correct regulator PM properties
ARM: dts: vexpress: Use assigned-clock-parents for sp810
pinctrl: tegra: Only set the gpio range if needed
arm: boot: dts: am4372: add ARM timers and SCU nodes
ARM: dts: AM4372: Add the am4372-rtc compatible string
ARM: shmobile: r8a7794 dtsi: Add CPG/MSTP Clock Domain
ARM: shmobile: r8a7793 dtsi: Add CPG/MSTP Clock Domain
...
gpio2_8 is connected to the PCIe_RESETn line and it has to be driven low to
reset the PCIe cards. Add gpios property to PCIe DT node.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tony Lindgren <tony@atomide.com>
pbias-supply is initialized in dra7.dtsi. Remove redundant initialization
of pbias-supply from MMC1 dt node in am57xx-beagle-x15.dts
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without this USB2 breaks if USB1 is disabled or USB1
initializes after USB2 e.g. due to deferred probing.
Fixes: 5a0f93c657 ("ARM: dts: Add am57xx-beagle-x15")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: stable@vger.kernel.org (v3.19+)
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM57xx Beagle X15 has a HDMI output. This patch adds the device tree
nodes required for HDMI.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: devicetree@vger.kernel.org
Acked-by: Tony Lindgren <tony@atomide.com>
BeagleBoard-X15 pre-production change includes switching the GPIO fan
gpio over from 1 to 2 to allow for a potential fix at a later point in
time for USB client VBUS detection using PMIC VBUS detect capability.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BeagleBoard-X15 pre-production change includes switching over to UART
pins that now allow for UART download capability. All original boards
should either have been returned for modifications or already modified
for the required change and maintaining compatibility for older boards
are no longer needed.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With commit bc078316d8 ("ARM: dts: DRA7: Add node for RTC"), we now
have AM57xx RTC register itself as alias 0 even before DS1307 or TPS
rtc drivers are loaded up. However, since neither TPS, nor AM57xx RTC
are capable of being backedup by battery, we would like to maintain
the "primary" rtc as mcp79410 rtc device.
This also generates the following warnings in the bootlog highlighting
the issue:
[ 5.895445] rtc-ds1307 2-006f: /aliases ID 0 not available
...
[ 6.476285] palmas-rtc 48070000.i2c:tps659038@58:tps659038_rtc: /aliases ID 1 not available
So, add proper aliases to ensure that RTC order is always consistent
to userspace immaterial of probe order.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The interrupt polarity provided in devicetree is used to configure
the interrupt controller(ARM GIC), however, it seems that we have an
inverter at the GIC boundary inside AM57xx which inverts the signal
input from sys_irq external interrupt source.
Further, as per GIC distributor TRM,
http://infocenter.arm.com/help/topic/com.arm.doc.ddi0438d/BGBHIACJ.html#BABJFCFB
ARM GIC distributor does not support IRQ trigger type
IRQ_TYPE_LEVEL_LOW, and only rising or level high signals.
However, for some reason, the current configuration(which gets ignored
by GIC driver) functions on some platforms, however, on few platforms
results in infinite interrupts hogging the system down.
Switch over to rising edge for GIC configuration which is also aligned
with trigger point from the RTC chip and the internal inversion.
Fixes: 5a0f93c657 ("ARM: dts: Add am57xx-beagle-x15")
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As always, this tends to be one of our bigger branches. There are lots of
updates this release, but not that many jumps out as something that needs
more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- More graphics DT pieces falling into place on Exynos, bridges, clocks.
- Plenty of DT updates for Qualcomm platforms for various IP blocks
- Some churn on Tegra due to switch-over to tool-generated pinctrl data
- Misc fixes and updates for Atmel at91 platforms
- Various DT updates to add IP block support on Broadcom's Cygnus platforms
- More updates for Renesas platforms as DT support is added for various IP
blocks (IPMMU, display, audio, etc).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wqhB
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As always, this tends to be one of our bigger branches. There are
lots of updates this release, but not that many jumps out as something
that needs more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- more graphics DT pieces falling into place on Exynos, bridges,
clocks.
- plenty of DT updates for Qualcomm platforms for various IP blocks
- some churn on Tegra due to switch-over to tool-generated pinctrl
data
- misc fixes and updates for Atmel at91 platforms
- various DT updates to add IP block support on Broadcom's Cygnus
platforms
- more updates for Renesas platforms as DT support is added for
various IP blocks (IPMMU, display, audio, etc)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (231 commits)
ARM: dts: alpine: add internal pci
Revert "ARM: dts: mt8135: Add pinctrl/GPIO/EINT node for mt8135."
ARM: mvebu: use 0xf1000000 as internal registers on Armada 370 DB
ARM: dts: qcom: Add idle state device nodes for 8064
ARM: dts: qcom: Add idle states device nodes for 8084
ARM: dts: qcom: Add idle states device nodes for 8974/8074
ARM: dts: qcom: Update power-controller device node for 8064 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8084 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8074 Krait CPUs
devicetree: bindings: Document qcom,idle-states
devicetree: bindings: Update qcom,saw2 node bindings
dt-bindings: Add #defines for MSM8916 clocks and resets
arm: dts: qcom: Add LPASS Audio HW to IPQ8064 device tree
arm: dts: qcom: Add APQ8084 chipset SPMI PMIC's nodes
arm: dts: qcom: Add 8x74 chipset SPMI PMIC's nodes
arm: dts: qcom: Add SPMI PMIC Arbiter nodes for APQ8084 and MSM8974
arm: dts: qcom: Add LCC nodes
arm: dts: qcom: Add TCSR support for MSM8960
arm: dts: qcom: Add TCSR support for MSM8660
arm: dts: qcom: Add TCSR support for IPQ8064
...
Here's the usual "low-priority fixes that didn't make it into the last
few -rcs, with a twist: We had a fixes pull request that I didn't send
in time to get into 4.0, so we'll send some of them to Greg for -stable as
well.
Contents here is as usual not all that controversial:
- A handful of randconfig fixes from Arnd, in particular for older Samsung
platforms
- Exynos fixes, !SMP building, DTS updates for MMC and lid switch
- Kbuild fix to create output subdirectory for DTB files
- Misc minor fixes for OMAP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o/4N
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's the usual "low-priority fixes that didn't make it into the last
few -rcs, with a twist: We had a fixes pull request that I didn't send
in time to get into 4.0, so we'll send some of them to Greg for
-stable as well.
Contents here is as usual not all that controversial:
- a handful of randconfig fixes from Arnd, in particular for older
Samsung platforms
- Exynos fixes, !SMP building, DTS updates for MMC and lid switch
- Kbuild fix to create output subdirectory for DTB files
- misc minor fixes for OMAP"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
ARM: at91/dt: sama5d3 xplained: add phy address for macb1
kbuild: Create directory for target DTB
ARM: mvebu: Disable CPU Idle on Armada 38x
ARM: DRA7: Enable Cortex A15 errata 798181
ARM: dts: am57xx-beagle-x15: Add thermal map to include fan and tmp102
ARM: dts: DRA7: Add bandgap and related thermal nodes
bus: ocp2scp: SYNC2 value should be changed to 0x6
ARM: dts: am4372: Add "ti,am437x-ocp2scp" as compatible string for OCP2SCP
ARM: OMAP2+: remove superfluous NULL pointer check
ARM: EXYNOS: Fix build breakage cpuidle on !SMP
ARM: dts: fix lid and power pin-functions for exynos5250-spring
ARM: dts: fix mmc node updates for exynos5250-spring
ARM: OMAP4: remove dead kconfig option OMAP4_ERRATA_I688
MAINTAINERS: add OMAP defconfigs under OMAP SUPPORT
ARM: OMAP1: PM: fix some build warnings on 1510-only Kconfigs
ARM: cns3xxx: don't export static symbol
ARM: S3C24XX: avoid a Kconfig warning
ARM: S3C24XX: fix header file inclusions
ARM: S3C24XX: fix building without PM_SLEEP
ARM: S3C24XX: use SAMSUNG_WAKEMASK for s3c2416
...
- Purge the gic_arch_extn hacks and abuse by using the new stacked domains
NOTE: Due to the nature of these changes, patches crossing subsystems have
been kept together in their own branches.
- tegra
- Handle the LIC properly
- omap
- Convert crossbar to stacked domains
- kill arm,routable-irqs in GIC binding
- exynos
- Convert PMU wakeup to stacked domains
- shmobile, ux500, zynq (irq_set_wake branch)
- Switch from abusing gic_arch_extn to using gic_set_irqchip_flags
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=IPgJ
-----END PGP SIGNATURE-----
Merge tag 'irqchip-core-4.1-3' of git://git.infradead.org/users/jcooper/linux into irq/core
irqchip core change for v4.1 (round 3) from Jason Cooper
Purge the gic_arch_extn hacks and abuse by using the new stacked domains
NOTE: Due to the nature of these changes, patches crossing subsystems have
been kept together in their own branches.
- tegra
- Handle the LIC properly
- omap
- Convert crossbar to stacked domains
- kill arm,routable-irqs in GIC binding
- exynos
- Convert PMU wakeup to stacked domains
- shmobile, ux500, zynq (irq_set_wake branch)
- Switch from abusing gic_arch_extn to using gic_set_irqchip_flags
This is mostly to enable errata 798181 and thermal support for dra7,
configure ocp2scp for am437x, remove dead code for OMAP4_ERRATA_I688
and fix build warnings for omap1510 only config.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Uqd0
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.1/fixes-0' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
Merge "omap non-urgent fixes for v4.1" from Tony Lindgren:
Fixes for omaps that were not considered urgent enough for the -rc cycle.
This is mostly to enable errata 798181 and thermal support for dra7,
configure ocp2scp for am437x, remove dead code for OMAP4_ERRATA_I688
and fix build warnings for omap1510 only config.
* tag 'omap-for-v4.1/fixes-0' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: DRA7: Enable Cortex A15 errata 798181
ARM: dts: am57xx-beagle-x15: Add thermal map to include fan and tmp102
ARM: dts: DRA7: Add bandgap and related thermal nodes
bus: ocp2scp: SYNC2 value should be changed to 0x6
ARM: dts: am4372: Add "ti,am437x-ocp2scp" as compatible string for OCP2SCP
ARM: OMAP2+: remove superfluous NULL pointer check
ARM: OMAP4: remove dead kconfig option OMAP4_ERRATA_I688
MAINTAINERS: add OMAP defconfigs under OMAP SUPPORT
ARM: OMAP1: PM: fix some build warnings on 1510-only Kconfigs
Signed-off-by: Olof Johansson <olof@lixom.net>
BeagleBoard-X15 has capability for a fan and has an onboard TMP102
temperature sensor as well. This allows us to create a new thermal
zone (called, un-imaginatively "board"), and allows us to use some
active cooling as temperatures start edge upward in the system by
creating a new alert temperature (emperically 50C) for cpu.
NOTE: Fan is NOT mounted by default on the platform, in such a case,
all we end up doing is switch on a regulator and leak very minimal
current.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we have EXTCON_USB_GPIO queued for v4.1, revert
commit addfcde7c4 ("ARM: dts: dra7x-evm: beagle-x15: Fix USB Host")
On these EVMs, the USB cable state has to be determined via the
ID pin tied to a GPIO line. We use the gpio-usb-extcon driver
to read the ID pin and the extcon framework to forward
the USB cable state information to the USB driver so the
controller can be configured in the right mode (host/peripheral).
Gets USB peripheral mode to work on this EVM.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Support for the TI crossbar used on the DRA7 family of chips
is implemented as an ugly hack on the side of the GIC.
Converting it to stacked domains makes it slightly more
palatable, as it results in a cleanup.
Unfortunately, as the DT bindings failed to acknowledge the
fact that this is actually yet another interrupt controller
(the third, actually), we have yet another breakage. Oh well.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088629-15377-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In commit 87517d26d8 ("ARM: dts: dra7-evm: Add extcon nodes for USB")
we enabled Extcon USB gpio to tackle the USB ID pin and get
peripheral mode to work.
But the extcon-gpio-usb driver [1] didn't make it into v4.0
and this makes the USB driver defer probe indefinitely breaking
USB Host functionality.
As a temporary fix we remove the extcon handle from the
USB controller and add it back when the extcon driver
merges in v4.1.
[1] - https://lkml.org/lkml/2015/2/2/187
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On this board USB2 is meant to be used as peripheral only.
The ID pin for USB2 is hardwired HIGH.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On this EVM, the USB cable state has to be determined via the
ID pin tied to a GPIO line. We use the gpio-usb-extcon driver
to read the ID pin and the extcon framework to forward
the USB cable state information to the USB driver so the
controller can be configured in the right mode (host/peripheral).
NOTE: the ports on this board cannot switch roles. They are
configured either host or peripheral by hardwiring the
respective ID pins.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
TPS gpio now controls a 5v 500mA TL5209 regulator which may be supply
a fan (such as AFB02505HHB) over J1 connector for various purposes.
Provide device tree node to enable the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add CPSW DT binding to beagle X15 DTS in order to
get ethernet working with this board.
Note that we're also adding sleep state which will
place all pins in mux mode 15 - which means "driver
off" - thus conserving power.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BeagleBoard-X15 is the next generation Open Source Hardware
BeagleBoard based on TI's AM5728 SoC featuring dual core 1.5GHz A15
processor. The platform features 2GB DDR3L (w/dual 32bit busses),
eSATA, 3 USB3.0 ports, integrated HDMI (1920x1080@60), separate LCD
port, video In port, 4GB eMMC, uSD, Analog audio in/out, dual 1G
Ethernet.
For more information, refer to:
BeagleBoard-X15 Wiki:
http://www.elinux.org/Beagleboard:BeagleBoard-X15
AM5728 is part of the Sitara product family whose additional details
will be available: http://www.ti.com/lsds/ti/arm/overview.page
Technical Reference Manual for AM5728 is public domain at:
http://www.ti.com/lit/spruhz6
Just add basic support for the moment, the following updates are needed:
i) Ethernet - depends on SoC dts fixes
ii) USB Client (USB2) - depends on GPIO extcon
ii) HDMI - additional driver fixes pending
iii) Audio - additional driver fixes pending
NOTE:
AM5728 Data Manual (SPRS915L - August 2014) section 4.1.1 states: "All
unused power supply balls must be supplied with the voltages specified
in the Section 5.2, Recommended Operating Conditions". This implies
that all unused voltage rails for AM5728 can never be switched off even
if the hardware blocks inside that voltage domain is unused. Switching
off these unused rails may result in stability issues on other domains
and increased leakage and power-on-hour impacts.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi