The device is very similar to (0x0fe6, 0x8101),
And works well with dm9601 driver.
Signed-off-by: Shahar Havivi <shaharh@redhat.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix the RTL8111DP turn off the power when DASH is enabled.
- RTL_GIGA_MAC_VER_27 must wait for tx finish before reset.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Adjust and remove certain settings of RTL8102E which are for previous chips.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-off-by: Francois Romieu <romieu@fr.zoreil.com>
It results in the wrong point address and influences RTL8168DP.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
DM9000 revision B needs 1 ms delay after PHY power-on.
PHY must be powered on by writing 0 into register DM9000_GPR before
all other settings will change (see Davicom spec and example code).
Remember, that register DM9000_GPR was not changed by reset sequence.
Without this fix the FIFO is out of sync and sends wrong data after
sequence of "ifconfig ethX down ; ifconfig ethX up".
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/sfc/ethtool.c: In function ‘efx_ethtool_self_test’:
drivers/net/sfc/ethtool.c:613: warning: the frame size of 1200 bytes
is larger than 1024 bytes
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/DMA-API-HOWTO.txt states:
"DMA transfers need to be synced properly in order for
the cpu and device to see the most uptodate and correct
copy of the DMA buffer."
Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As reported and found by Johannes Stezenbach:
rt2800{pci,usb} do not report the Michael MIC in RXed frames, but do check
the Michael MIC in hardware. Therefore we have to report to mac80211 that the
received frame does not include the Michael MIC.
https://bugzilla.kernel.org/show_bug.cgi?id=16608
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fast channel change fixes:
a) Always set OFDM timings
b) Don't re-activate PHY
c) Enable only NF calibration, not AGC
https://bugzilla.kernel.org/show_bug.cgi?id=27382
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
net: deinit automatic LIST_HEAD
net: dont leave active on stack LIST_HEAD
net: provide default_advmss() methods to blackhole dst_ops
tg3: Restrict phy ioctl access
drivers/net: Call netif_carrier_off at the end of the probe
ixgbe: work around for DDP last buffer size
ixgbe: fix panic due to uninitialised pointer
e1000e: flush all writebacks before unload
e1000e: check down flag in tasks
isdn: hisax: Use l2headersize() instead of dup (and buggy) func.
arp_notify: unconditionally send gratuitous ARP for NETDEV_NOTIFY_PEERS.
cxgb4vf: Use defined Mailbox Timeout
cxgb4vf: Quiesce Virtual Interfaces on shutdown ...
cxgb4vf: Behave properly when CONFIG_DEBUG_FS isn't defined ...
cxgb4vf: Check driver parameters in the right place ...
pch_gbe: Fix the MAC Address load issue.
iwlwifi: Delete iwl3945_good_plcp_health.
net/can/softing: make CAN_SOFTING_CS depend on CAN_SOFTING
netfilter: nf_iterate: fix incorrect RCU usage
pch_gbe: Fix the issue that the receiving data is not normal.
...
Correct channel setting function must be used for AR2317.
When I tested ahb patch on bullet2 all seemed to work fine,
but it couldn't connect another host (using ibss for example).
During an analysis I observed that it's transmitting on another
channel. I looked into madwifi code and understood that
the problem is in channel setting function. So atheros RF2317 not
fully handled in the current ath5k version and must be patched.
Signed-off-by: Nikolay Ledovskikh <nledovskikh@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
taken two RT35XX EDIMAX from DPO_RT3562_3592_3062_LinuxSTA_V2.4.1.1_20101217
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'fixes-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: make sure MAYDAY_INITIAL_TIMEOUT is at least 2 jiffies long
workqueue, freezer: unify spelling of 'freeze' + 'able' to 'freezable'
workqueue: wake up a worker when a rescuer is leaving a gcwq
If management firmware is present and the device is down, the firmware
will assume control of the phy. If a phy access were allowed from the
host, it will collide with firmware phy accesses, resulting in
unpredictable behavior. This patch fixes the problem by disallowing phy
accesses during the problematic condition.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without calling of netif_carrier_off at the end of the probe the operstate
is unknown when the device is initially opened. By default the carrier is
on so when the device is opened and netif_carrier_on is called the link
watch event is not fired and operstate remains zero (unknown).
This patch fixes this behavior in forcedeth and r8169.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A HW limitation was recently discovered where the last buffer in a DDP offload
cannot be a full buffer size in length. Fix the issue with a work around by
adding another buffer with size = 1.
Signed-off-by: Amir Hanania <amir.hanania@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Systems containing an 82599EB and running a backported driver from
upstream were panicing on boot. It turns out hw->mac.ops.setup_sfp is
only set for 82599, so one should check to be sure that pointer is set
before continuing in ixgbe_sfp_config_module_task. I verified by
inspection that the upstream driver has the same issue and also added a
check before the call in ixgbe_sfp_link_config.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was not flushing all writebacks before unloading, possibly
causing memory to be written by the hardware after the driver had
reinitialized the rings.
This adds missing functionality to flush any pending writebacks and is
called in all spots where descriptors should be completed before the driver
begins processing.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is part of a fix to avoid any tasks running while the driver is
exiting and deinitializing resources.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are two spellings in use for 'freeze' + 'able' - 'freezable' and
'freezeable'. The former is the more prominent one. The latter is
mostly used by workqueue and in a few other odd places. Unify the
spelling to 'freezable'.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Steven Whitehouse <swhiteho@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: set flow handler for secondary interrupt controller of 5249
m68knommu: remove use of IRQ_FLG_LOCK from 68360 platform support
m68knommu: fix dereference of port.tty
m68knommu: add missing linker __modver section
m68knommu: fix mis-named variable int set_irq_chip loop
m68knommu: add optimize memmove() function
m68k: remove arch specific non-optimized memcmp()
m68knommu: fix use of un-defined _TIF_WORK_MASK
m68knommu: Rename m548x_wdt.c to m54xx_wdt.c
m68knommu: fix m548x_wdt.c compilation after headers renaming
m68knommu: Remove dependencies on nonexistent M68KNOMMU
VF Driver should use mailbox command timeout specified in t4fw_interface.h
rather than hard-coded value of 500ms.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a Virtual Machine is rebooted, KVM currently fails to issue a Function
Level Reset against any "Attached PCI Devices" (AKA "PCI Passthrough"). In
addition to leaving the attached device in a random state in the next booted
kernel (which sort of violates the entire idea of a reboot reseting hardware
state), this leaves our peer thinking that the link is still up. (Note that
a bug has been filed with the KVM folks, #25332, but there's been no
response on that as of yet.) So, we add a "->shutdown()" method for the
Virtual Function PCI Device to handle administrative shutdowns like a
reboot.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_DEBUG_FS we get "ERR_PTR()"s back from the debugfs routines
instead of NULL. Use the right predicates to check for this.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check module parameter validity in the module initialization routine instead
of the PCI Device Probe routine.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the specification of hardware,
the processing at the time of driver starting was modified.
This device write automatically the MAC address read from serial ROM
into a MAC Adress1A/1B register at the time of power on reset.
However, when stable clock is not supplied,
the writing of MAC Adress1A/1B register may not be completed.
In this case, it is necessary to load MAC address to MAC Address1A/1B register
by the MAC Address1 load register.
This patch always does the above processing,
in order not to be dependent on system environment.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes this build warning:
drivers/net/wireless/iwlwifi/iwl-3945.c:411:13: warning: 'iwl3945_good_plcp_health' defined but not used
As per Johannes Berg.
Signed-off-by: David S. Miller <davem@davemloft.net>
The statement 'select CAN_SOFTING' may ignore the dependancies
for CAN_SOFTING while selecting CAN_SOFTING_CS, as is therefore a bad choice.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This PCH_GBE driver had an issue that the receiving data is not normal.
This driver had not removed correctly the padding data
which the DMA include in receiving data.
This patch fixed this issue.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables it by default when the driver starts.
This has been required by many people and seems to actually be
useful on STB.
At any rate, the WoL modes can be selected and turned-on/off
by using the ethtool at run-time by users.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In drivers/net/usb/hso.c::hso_create_bulk_serial_device() we have this
code:
...
serial = kzalloc(sizeof(*serial), GFP_KERNEL);
if (!serial)
goto exit;
...
exit:
hso_free_tiomget(serial);
...
hso_free_tiomget() directly dereferences its argument, which in the
example above is a NULL pointer, ouch.
I could just add a 'if (serial)' test at the 'exit' label, but since most
freeing functions in the kernel accept NULL pointers (and it seems like
this was also assumed here) I opted to instead change 'hso_free_tiomget()'
so that it is safe to call it with a NULL argument. I also modified the
function to get rid of a pointles conditional before the call to
'usb_free_urb()' since that function already tests for NULL itself -
besides fixing the NULL deref this change also buys us a few bytes in
size.
Before:
$ size drivers/net/usb/hso.o
text data bss dec hex filename
32200 592 9960 42752 a700 drivers/net/usb/hso.o
After:
$ size drivers/net/usb/hso.o
text data bss dec hex filename
32196 592 9960 42748 a6fc drivers/net/usb/hso.o
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll leak the memory allocated to 'urb' in
drivers/net/usb/usbnet.c:kevent() when we 'goto fail_lowmem' and the 'urb'
variable goes out of scope while still completely unused.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
virtio_net: Add schedule check to napi_enable call
x25: Do not reference freed memory.
pch_can: fix tseg1/tseg2 setting issue
isdn: hysdn: Kill (partially buggy) CVS regision log reporting.
can: softing_cs needs slab.h
pch_gbe: Fix the issue which a driver locks when rx offload is set by ethtool
netfilter: nf_conntrack: set conntrack templates again if we return NF_REPEAT
pch_can: fix module reload issue with MSI
pch_can: fix rmmod issue
pch_can: fix 800k comms issue
net: Fix lockdep regression caused by initializing netdev queues too early.
net/caif: Fix dangling list pointer in freed object on error.
USB CDC NCM errata updates for cdc_ncm host driver
CDC NCM errata updates for cdc.h
ixgbe: update version string
ixgbe: cleanup variable initialization
ixgbe: limit VF access to network traffic
ixgbe: fix for 82599 erratum on Header Splitting
ixgbe: fix variable set but not used warnings by gcc 4.6
e1000: add support for Marvell Alaska M88E1118R PHY
...
Under harsh testing conditions, including low memory, the guest would
stop receiving packets. With this patch applied we no longer see any
problems in the driver while performing these tests for extended periods
of time.
Make sure napi is scheduled subsequent to each napi_enable.
Signed-off-by: Bruce Rogers <brogers@novell.com>
Signed-off-by: Olaf Kirch <okir@suse.de>
Cc: stable@kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patch "[PATCH 1/3] pch_can: fix 800k comms issue" is wrong.
I should have modified tseg1_min not tseg2_min.
This patch reverts tseg2_min to 1 and set tseg1_min to 2.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Randy Dunlap <randy.dunlap@oracle.com>
softing_cs.c uses kzalloc & kfree, so it needs to include linux/slab.h.
drivers/net/can/softing/softing_cs.c:234: error: implicit declaration of function 'kfree'
drivers/net/can/softing/softing_cs.c:271: error: implicit declaration of function 'kzalloc'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=654599
Many users report very low speed problem on 3945 devices,
this patch fixes problem, but only for some of them.
For unknown reason, sometimes after hw scanning, device is not able
to receive frames at high rate. Since plcp health check may request
hw scan to "reset radio", performance problem start to be observable
after update kernel to .35, where plcp check was introduced.
Bug reporter confirmed that removing plcp check fixed problem for him.
Reported-and-tested-by: SilvioTO <silviotoya@yahoo.it>
Cc: stable@kernel.org # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This driver will be in a deadlock, When the rx offload is set by ethtool.
The pch_gbe_reinit_locked function was modified.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, in case reload pch_can,
pch_can not to be able to catch interrupt.
The cause is bus-master is not set in pch_can.
Thus, add enabling bus-master processing.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when rmmod pch_can, kernel failure occurs.
The cause is pci_iounmap executed before pch_can_reset.
Thus pci_iounmap moves after pch_can_reset.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, 800k comms fails since prop_seg set zero.
(EG20T PCH CAN register of prop_seg must be set more than 1)
To prevent prop_seg set to zero, change tseg2_min 1 to 2.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Specification links:
- CDC NCM errata link:
http://www.usb.org/developers/devclass_docs/NCM10_012011.zip
- CDC and WMC errata link:
http://www.usb.org/developers/devclass_docs/CDC1.2_WMC1.1_012011.zip
Changes:
- driver updated to match cdc.h header with errata changes
- added support for USB_CDC_SET_NTB_INPUT_SIZE control request with
8 byte length
- fixes to comply with specification: send only control requests supported by
device, set number of datagrams for IN direction, connection speed structure
update, etc.
- packet loss fixed for tx direction; misleading flag renamed.
- adjusted hard_mtu value.
Signed-off-by: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will synchronize the version string with that of the latest source
forge driver which shares its functionality.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller