Commit Graph

12 Commits

Author SHA1 Message Date
Baruch Siach c43593d81a dt-bindings: net: don't confuse with generic PHY property
This complements commit 9a94b3a4bd (dt-binding: phy: don't confuse with
Ethernet phy properties).

The generic PHY 'phys' property sometime appears in the same node with
the Ethernet PHY 'phy' or 'phy-handle' properties. Add a warning in
ethernet.txt to reduce confusion.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-09-08 20:49:42 -07:00
Linus Torvalds dd6ec12f3b DeviceTree for 4.13:
- vsprintf format specifier %pOF for device_node's. This will enable us
   to stop storing the full node names. Conversion of users will happen
   next cycle.
 
 - Update documentation to point to DT specification instead of ePAPR.
 
 - Split out graph and property functions to a separate file.
 
 - New of-graph functions for ALSA
 
 - Add vendor prefixes for RISC-V, Linksys, iWave Systems, Roofull,
   Itead, and BananaPi.
 
 - Improve dtx_diff utility filename printing.
 -----BEGIN PGP SIGNATURE-----
 
 iQItBAABCAAXBQJZXpNsEBxyb2JoQGtlcm5lbC5vcmcACgkQ+vtdtY28YcO2gg//
 VxhXDs6+oTkBCUzVtEHue/yv44q8Sa7M3jY3/VqVSLa3Eopp/4dmDgBAtWYYX2ou
 KfUl0+yD4cSKhw6oxycwsaS61zf8JkM4sbXYQTphty/5lwxq0/i3OGj98Uk9w9JH
 kM+b1Wi7Z6GBzqh1GuS4E+ADSktMadxd0LugXZvDEMVQZusv/nzWxzq/bdMUqW19
 0nvBL9ABRAPirhBuMSWpYlEEkwQn7JF3LO3i8IBDhhFzMsvbfR7cTp+ydt6I2pk8
 h8DxlsaPIOWH5KePNEmzsd1VlV/HcNl7/vZb0ev0Eb94TLHJRJ7V0ZMQxc5vxHgN
 x6aMlBLHGzG6LI5CV30pWAD/qrrtXNbqmlj1Qjd+FXen6NuQSngSfo5aXzXrM6X5
 ZUD7ou9KzYObraOarU6w2qSICok85bGQHOiBQDVTmE4E/4AVscnc1VQi/rTHrt2O
 Yt3AV8iwaum8q2PVOVKdy8tu7x/7BzBdSObYtjjMIuWcrInnlIyUkmehtCl38kqV
 fd6OIVEOhTJTr0CYDiXEbKtG81j7JhoREdVZvzcEhWFGt/98Rjc9tkTihhFzky4m
 D6lpzpf8mvemrBiMegyQbhVcfHyo0fJe+6giV7cssf2Xhe1QkC15UXywbccO7xFJ
 nf3yqCl8YVEPG0l1MrR+YEHHcnr4ZIEZpejOv+SzZeg=
 =DNwf
 -----END PGP SIGNATURE-----

Merge tag 'devicetree-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux

Pull DeviceTree updates from Rob Herring:

 - vsprintf format specifier %pOF for device_node's. This will enable us
   to stop storing the full node names. Conversion of users will happen
   next cycle.

 - Update documentation to point to DT specification instead of ePAPR.

 - Split out graph and property functions to a separate file.

 - New of-graph functions for ALSA

 - Add vendor prefixes for RISC-V, Linksys, iWave Systems, Roofull,
   Itead, and BananaPi.

 - Improve dtx_diff utility filename printing.

* tag 'devicetree-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (32 commits)
  of: document /sys/firmware/fdt
  dt-bindings: Add RISC-V vendor prefix
  vsprintf: Add %p extension "%pOF" for device tree
  of: find_node_by_full_name rewrite to compare each level
  of: use kbasename instead of open coding
  dt-bindings: thermal: add file extension to brcm,ns-thermal
  of: update ePAPR references to point to Devicetree Specification
  scripts/dtc: dtx_diff - Show real file names in diff header
  of: detect invalid phandle in overlay
  of: be consistent in form of file mode
  of: make __of_attach_node() static
  of: address.c header comment typo
  of: fdt.c header comment typo
  of: make of_fdt_is_compatible() static
  dt-bindings: display-timing.txt convert non-ascii characters to ascii
  Documentation: remove overlay-notes reference to non-existent file
  dt-bindings: usb: exynos-usb: Add missing required VDD properties
  dt-bindings: Add vendor prefix for Linksys
  MAINTAINERS: add device tree ABI documentation file
  of: Add vendor prefix for iWave Systems Technologies Pvt. Ltd
  ...
2017-07-07 10:37:54 -07:00
Florian Fainelli 29b65f5f97 dt-bindings: Add "internal" as a valid 'phy-mode' property
A number of Ethernet MACs have internal Ethernet PHYs and the internal
wiring makes it so that this knowledge needs to be available using the
standard 'phy-mode' property.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-23 15:06:42 -04:00
Frank Rowand 076fb0c4b6 of: update ePAPR references to point to Devicetree Specification
The Devicetree Specification has superseded the ePAPR as the
base specification for bindings.  Update files in Documentation
to reference the new document.

First reference to ePAPR in Documentation/devicetree/bindings/arm/cci.txt
is generic, remove it.

Some files are not updated because there is no hypervisor chapter
in the Devicetree Specification:
   Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt
   Documenation/virtual/kvm/api.txt
   Documenation/virtual/kvm/ppc-pv.txt

Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
2017-06-22 11:22:06 -05:00
Russell King c125ca0918 net: phy: add XAUI and 10GBASE-KR PHY connection types
XAUI allows XGMII to reach an extended distance by using a XGXS layer at
each end of the MAC to PHY link, operating over four Serdes lanes.

10GBASE-KR is a single lane Serdes backplane ethernet connection method
with autonegotiation on the link.  Some PHYs use this to connect to the
ethernet interface at 10G speeds, switching to other connection types
when utilising slower speeds.

10GBASE-KR is also used for XFI and SFI to connect to XFP and SFP fiber
modules.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-06 21:14:13 -04:00
Andrew Lunn 55601a8806 net: phy: Add 2000base-x, 2500base-x and rxaui modes
The mv88e6390 ports 9 and 10 supports some additional PHY modes. Add
these modes to the PHY core so they can be used in the binding.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-07 10:34:42 -05:00
Martin Blumenstingl e5f3a4a56c Documentation: devicetree: clarify usage of the RGMII phy-modes
RGMII requires special RX and/or TX delays depending on the actual
hardware circuit/wiring. These delays can be added by the MAC, the PHY
or the designer of the circuit (the latter means that no delay has to
be added by PHY or MAC).
There are 4 RGMII phy-modes used describe where a delay should be
applied:
- rgmii: the RX and TX delays are either added by the MAC (where the
  exact delay is typically configurable, and can be turned off when no
  extra delay is needed) or not needed at all (because the hardware
  wiring adds the delay already). The PHY should neither add the RX nor
  TX delay in this case.
- rgmii-rxid: configures the PHY to enable the RX delay. The MAC should
  not add the RX delay in this case.
- rgmii-txid: configures the PHY to enable the TX delay. The MAC should
  not add the TX delay in this case.
- rgmii-id: combines rgmii-rxid and rgmii-txid and thus configures the
  PHY to enable the RX and TX delays. The MAC should neither add the RX
  nor TX delay in this case.

Document these cases in the ethernet.txt documentation to make it clear
when to use each mode.
If applied incorrectly one might end up with MAC and PHY both enabling
for example the TX delay, which breaks ethernet TX traffic on 1000Mbit/s
links.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-28 12:06:54 -05:00
Sean Wang 4ce4862a81 Documentation: devicetree: revise ethernet device-tree binding about TRGMII
add phy-mode "trgmii" to
Documentation/devicetree/bindings/net/ethernet.txt

Cc: devicetree@vger.kernel.org
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-24 08:26:09 -04:00
Stas Sergeev 4cba5c2103 of_mdio: add new DT property 'managed' to specify the PHY management type
Currently the PHY management type is selected by the MAC driver arbitrary.
The decision is based on the presence of the "fixed-link" node and on a
will of the driver's authors.
This caused a regression recently, when mvneta driver suddenly started
to use the in-band status for auto-negotiation on fixed links.
It appears the auto-negotiation may not work when expected by the MAC driver.
Sebastien Rannou explains:
<< Yes, I confirm that my HW does not generate an in-band status. AFAIK, it's
a PHY that aggregates 4xSGMIIs to 1xQSGMII ; the MAC side of the PHY (with
inband status) is connected to the switch through QSGMII, and in this context
we are on the media side of the PHY. >>
https://lkml.org/lkml/2015/7/10/206

This patch introduces the new string property 'managed' that allows
the user to set the management type explicitly.
The supported values are:
"auto" - default. Uses either MDIO or nothing, depending on the presence
of the fixed-link node
"in-band-status" - use in-band status

Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>

CC: Rob Herring <robh+dt@kernel.org>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Kumar Gala <galak@codeaurora.org>
CC: Florian Fainelli <f.fainelli@gmail.com>
CC: Grant Likely <grant.likely@linaro.org>
CC: devicetree@vger.kernel.org
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-21 16:12:55 -07:00
Vince Bridgers 13967f0c2a stmmac: Add properties for transmit and receive fifo sizes
The Synopsys stmmac fifo sizes are configurable, and need to be known
in order to configure certain controller features. This patch adds
tx-fifo-depth and rx-fifo-depth properties to the stmmac document
file.

Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-16 13:58:42 -04:00
Thomas Petazzoni b9d12085f2 net: phy: add minimal support for QSGMII PHY
This commit adds the necessary definitions for the PHY layer to
recognize "qsgmii" as a valid PHY interface. A QSMII interface, as
defined at
http://en.wikipedia.org/wiki/Media_Independent_Interface#Quad_Serial_Gigabit_Media_Independent_Interface,
is "is a method of combining four SGMII lines into a 5Gbit/s
interface. QSGMII, like SGMII, uses LVDS signalling for the TX and RX
data and a single LVDS clock signal. QSGMII uses significantly fewer
signal lines than four SGMII busses."

This type of MAC <-> PHY connection might require special handling on
the MAC driver side, so it should be possible to express this type of
MAC <-> PHY connection, for example in the Device Tree.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: devicetree@vger.kernel.org
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-16 14:36:12 -04:00
Sergei Shtylyov e8f08ee0ad DT: net: document Ethernet bindings in one place
This patch is an attempt to gather the Ethernet related bindings in one file,
like it's done in the MMC and some other subsystems. It should save some of
the trouble of documenting several properties over and over in each binding
document, instead only making reference to the main file.

I have used the Embedded Power Architecture(TM) Platform Requirements (ePAPR)
standard as a base for the properties description, also documenting some ad-hoc
properties that have been introduced over time despite having direct analogs in
ePAPR.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-18 17:05:39 -05:00