The help text of CONFIG_MTD_OF_PARTS refers to additional documentation
in booting-without-of.txt but this documentation was moved to another
file in commit efcc2da3fd (Stefan Roese:
Factor MTD physmap bindings out of booting-without-of). This updates the
help text to point to the right place.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
[Brian: fixed doc reference]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
update a comment in nand_command_lp() about specific requirements of
individual commands, the DEPLETE1 command was removed in the past and
the comment no longer applied
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
For the DDR Quad read, the dummy cycles maybe 3 or 6 which is less then 8.
The dummy cycles is actually 8 for SPI fast/dual/quad read.
This patch makes preparations for the DDR quad read, it fixes the wrong dummy
value for both the spi-nor.c and m25p80.c.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
NAND devices with page sizes over 4 KiB require more than 4-bits of ECC
coverage. This patch calculates the value of ecc_bytes based on a still
assumed 512-byte step size (13-bits) and the ecc_strength.
Example:
Micron M73A devices (8 KiB page) require 8-bit ECC per 512-byte
Signed-off-by: Jordan Friendshuh <jfriendshuh@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The drivers/mtd/nand/gpio.c driver does not GPIO bitbang the complete
NAND protocol, but instead is GPIO _assisted_ -- a memory mapped interface
communicates commands and data, and only few control signals are connected
to GPIO pins.
Expand comments in the driver source and in the Kconfig description to
better reflect the very nature of the driver. The previous text could be
mistaken for complete GPIO bitbanging.
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* A regression from 3.16 which was noticed in 3.17. With the restructuring of
the m25p80.c driver and the SPI NOR library framework, we omitted proper
listing of the SPI device IDs. This means m25p80.c wouldn't auto-load
(modprobe) properly when built as a module. For now, we duplicate the device
IDs into both modules.
* The OMAP / ELM modules were depending on an implicit link ordering. Use
deferred probing so that the new link order (in 3.18-rc) can still allow for
successful probing.
* Fix suspend/resume support for LH28F640BF NOR flash
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=IxjM
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20141102' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"Three main MTD fixes for 3.18:
- A regression from 3.16 which was noticed in 3.17. With the
restructuring of the m25p80.c driver and the SPI NOR library
framework, we omitted proper listing of the SPI device IDs. This
means m25p80.c wouldn't auto-load (modprobe) properly when built as
a module. For now, we duplicate the device IDs into both modules.
- The OMAP / ELM modules were depending on an implicit link ordering.
Use deferred probing so that the new link order (in 3.18-rc) can
still allow for successful probing.
- Fix suspend/resume support for LH28F640BF NOR flash"
* tag 'for-linus-20141102' of git://git.infradead.org/linux-mtd:
mtd: cfi_cmdset_0001.c: fix resume for LH28F640BF chips
mtd: omap: fix mtd devices not showing up
mtd: m25p80,spi-nor: Fix module aliases for m25p80
mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
mtd: m25p80: get rid of spi_get_device_id
After '#echo mem > /sys/power/state' some devices can not be properly resumed
because apparently the MTD Partition Configuration Register has been reset
to default thus the rootfs cannot be mounted cleanly on resume.
An example of this can be found in the SA-1100 Developer's Manual at 9.5.3.3
where the second step of the Sleep Shutdown Sequence is described:
"An internal reset is applied to the SA-1100. All units are reset...".
As workaround we refresh the PCR value as done initially on chip setup.
This behavior and the fix are confirmed by our tests done on 2 different Zaurus
collie units with kernel 3.17.
Fixes: 812c5fa82bae: ("mtd: cfi_cmdset_0001.c: add support for Sharp LH28F640BF NOR")
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Since commit 6d178ef2fd ("mtd: nand: Move ELM driver and rename as
omap_elm"), I don't have any mtd devices present on my am335x. This
changes the link order of the omap_elm and omap2 objects, causing them
to probe in the wrong order.
To fix this, make elm_config defer probing until the omap_elm driver is
actually loaded.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add support for the sunxi NAND Flash Controller (NFC).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Brian: tweaked to fix ecc->steps issue]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
nandsim can simulate NAND Flash which returns the ID bytes specified
by first_id_byte, ..., fourth_id_byte module parameters.
In order to simulate NAND flash which returns more than four ID bytes,
this adds id_bytes module parameter which is specified by the array of
byte like this:
# modprobe nandsim id_bytes=0x98,0xdc,0x90,0x26,0x76,0x15,0x01,0x08 bch=1
This doesn't add fifth_id_byte, ..., seventh_id_byte module parameters,
because they are redundant. But the existing first_id_byte, ...,
fourth_id_byte module parameters are preserved and add "(obsolete)" to
the description.
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
With CONFIG_OF=n, we can see the following warning:
drivers/mtd/devices/docg3.c:2122:28: warning: 'docg3_dt_ids' defined but not used [-Wunused-variable]
static struct of_device_id docg3_dt_ids[] = {
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Sometimes the trx offsets are 0, in that case there is no partition and
we should not try to add one.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[Brian: rewrapped]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Modify phram to include <linux/io.h> rather than <asm/io.h>
Signed-off-by: Rob Ward <robert.ward114@googlemail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When clk_prepare_enable(q->clk) fails it is clearer to disable the previous
acquired clock (q->clk_en) in the error path rather than doing it locally.
So disable q->clk_en in the error path only.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The 'map_failed' label will return 'ret', so we need to assign the error
code to 'ret', otherwise the probe function will return success.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This replaces kzalloc() and ioremap() calls by devm_ functions
in the probe() routine, which automatically release the corresponding
resources when probe() fails or when the device is removed.
This simplifies simplifies the error management code, and brings
the below improvements or changes:
A. Fixing a bug reported by "make coccicheck":
If "board = devm_kzalloc()" fails, the probe() function jumps
incorrectly to label "no_res" and therefore returns without
running iounmap().
B. Requesting the memory region
Using devm_ioremap_resource() makes the probe() function request
the corresponding memory region before running ioremap(), as
it is supposed to do.
C. Standardizing the error codes:
The use of devm_ioremap_resource() changes the return value:
* -ENOMEM instead of -EIO in case of ioremap() failure,
* -EINVAL instead of -ENODEV in case of platform_get_resource()
failure.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This is needed for some new Netgear devices (e.g. R6250).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Avoid the following compile warning:
drivers/mtd/maps/bfin-async-flash.c: In function 'bfin_flash_probe':
drivers/mtd/maps/bfin-async-flash.c:129: warning: unused variable 'ret'
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add device-tree support. This is straightforward as docg3 only uses the
standard IOMEM resources.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Since the commit 97a288ba2c ("ARM: omap2+: gpmc-nand: Use
dynamic platform_device_alloc()") gpmc-nand driver supports
multiple NAND flash devices connected to the single controller.
Remove global variable to make the code thread-safe.
Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is currently no useful way to override the default
implementation of this operation. The returned struct spi_device_id
must have a pointer to struct flash_info in its private data, but this
structure is defined inside spi-nor.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
seq_printf doesn't return a useful value, so remove
these misuses.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
m25p80's device ID table is now spi_nor_ids, defined in spi-nor. The
MODULE_DEVICE_TABLE() macro doesn't work with extern definitions, but
its use was also removed at the same time. Now if m25p80 is built as
a module it doesn't get the necessary aliases to be loaded
automatically.
A clean solution to this will involve defining the list of device
IDs in spi-nor.h and removing struct spi_device_id from the spi-nor
API, but this is quite a large change.
As a quick fix suitable for stable, copy the device IDs back into
m25p80.
Fixes: 03e296f613 ("mtd: m25p80: use the SPI nor framework")
Cc: <stable@vger.kernel.org> # 3.16.x: 32f1b7c8352f: mtd: move support for struct flash_platform_data into m25p80
Cc: <stable@vger.kernel.org> # 3.16.x: 90e55b3812a1: mtd: m25p80: get rid of spi_get_device_id
Cc: <stable@vger.kernel.org> # 3.16.x: 70f3ce0510af: mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
Cc: <stable@vger.kernel.org> # 3.16.x
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
Pull block layer driver update from Jens Axboe:
"This is the block driver pull request for 3.18. Not a lot in there
this round, and nothing earth shattering.
- A round of drbd fixes from the linbit team, and an improvement in
asender performance.
- Removal of deprecated (and unused) IRQF_DISABLED flag in rsxx and
hd from Michael Opdenacker.
- Disable entropy collection from flash devices by default, from Mike
Snitzer.
- A small collection of xen blkfront/back fixes from Roger Pau Monné
and Vitaly Kuznetsov"
* 'for-3.18/drivers' of git://git.kernel.dk/linux-block:
block: disable entropy contributions for nonrot devices
xen, blkfront: factor out flush-related checks from do_blkif_request()
xen-blkback: fix leak on grant map error path
xen/blkback: unmap all persistent grants when frontend gets disconnected
rsxx: Remove deprecated IRQF_DISABLED
block: hd: remove deprecated IRQF_DISABLED
drbd: use RB_DECLARE_CALLBACKS() to define augment callbacks
drbd: compute the end before rb_insert_augmented()
drbd: Add missing newline in resync progress display in /proc/drbd
drbd: reduce lock contention in drbd_worker
drbd: Improve asender performance
drbd: Get rid of the WORK_PENDING macro
drbd: Get rid of the __no_warn and __cond_lock macros
drbd: Avoid inconsistent locking warning
drbd: Remove superfluous newline from "resync_extents" debugfs entry.
drbd: Use consistent names for all the bi_end_io callbacks
drbd: Use better variable names
NAND
* Cleanup for Denali driver
* Atmel: add support for new page sizes
* Atmel: fix up 'raw' mode support
* Atmel: miscellaneous cleanups
* New timing mode helpers for non-ONFI NAND
* OMAP: allow driver to be (properly) built as a module
* bcm47xx: RESET support and other cleanups
SPI NOR
* Miscellaneous cleanups, to prepare framework for wider use (some further
work still pending)
* Compile-time configuration to select 4K vs. 64K support for flash that
support both (necessary for using UBIFS on some SPI NOR)
A few scattered code quality fixes, detected by Coverity
See the changesets for more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUP2dfAAoJEFySrpd9RFgtiUYQAKHmzTw4UR5lZNwBHLPIk5mV
d11If+kGwY5wVTG0f7+d0RxXWQLP11LnWn7S9JK3ttvuc5L8ev4jCjtbR6aRQZgy
6vdqqvOv/kqP+Q4FclVIdEPzEgLurg4zCuVoDaMkhIKkdmrcw3inWSt7F+/2dJYb
OAPRoOSv8hnmQheH85v8zpHrovcYLY9tGoSlv0Yu8pKapyp7LT2E/wPaXh16VjZG
A8Qr6NsSZR/5UY5RZmMewkKkB/T25miPwwdiXvdwbWoKRn8pPlg/NJ9ae8BXcyFg
GsOuQWnjdDJE+Orud5IBWEARpW98SbtksQSVtoZPLE4iK9gglsUgiXAI2W8/MQkP
cvmGDz1q80jNF4m/RJSY9frGXRCK3ICOue6g24JDmgioQYZ/Weqo0gtpYQnYiWPb
lYsNgNrOM2clLVnVbUMD5LwFf7oEspgZkyqirwaqJ+lP3Elyc6VTr3BvClQpdpyb
tZ7g5PC/zlU+IcFbiGCgsvkoFsWQ7aT0thchNn4RmP8QbNNL/OJ1gIMat0at2Aon
nqYfkJVi/a7lHCYmhP9rdEWqhOSljtvyjeE7A5XSPVlYxP+xSOyyEKDCcIbh8chH
pC11WASnbDRP/ldAuZf67s2ot62u1sD3Az4fdYgf04wFpq7s52MLkeThUrSsm2L0
ljLrSCV/8l2XYqvyYBQm
=/jCH
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20141015' of git://git.infradead.org/linux-mtd
Pull MTD update from Brian Norris:
"Sorry for delaying this a bit later than usual. There's one mild
regression from 3.16 that was noticed during the 3.17 cycle, and I
meant to send a fix for it along with this pull request. I'll
probably try to queue it up for a later pull request once I've had a
better look at it, hopefully by -rc2 at the latest.
Summary for this pull:
NAND
- Cleanup for Denali driver
- Atmel: add support for new page sizes
- Atmel: fix up 'raw' mode support
- Atmel: miscellaneous cleanups
- New timing mode helpers for non-ONFI NAND
- OMAP: allow driver to be (properly) built as a module
- bcm47xx: RESET support and other cleanups
SPI NOR
- Miscellaneous cleanups, to prepare framework for wider use (some
further work still pending)
- Compile-time configuration to select 4K vs. 64K support for flash
that support both (necessary for using UBIFS on some SPI NOR)
A few scattered code quality fixes, detected by Coverity
See the changesets for more"
* tag 'for-linus-20141015' of git://git.infradead.org/linux-mtd: (59 commits)
mtd: nand: omap: Correct CONFIG_MTD_NAND_OMAP_BCH help message
mtd: nand: Force omap_elm to be built as a module if omap2_nand is a module
mtd: move support for struct flash_platform_data into m25p80
mtd: spi-nor: add Kconfig option to disable 4K sectors
mtd: nand: Move ELM driver and rename as omap_elm
nand: omap2: Replace pr_err with dev_err
nand: omap2: Remove horrible ifdefs to fix module probe
mtd: nand: add Hynix's H27UCG8T2ATR-BC to nand_ids table
mtd: nand: support ONFI timing mode retrieval for non-ONFI NANDs
mtd: physmap_of: Add non-obsolete map_rom probe
mtd: physmap_of: Fix ROM support via OF
MAINTAINERS: add l2-mtd.git, 'next' tree for MTD
mtd: denali: fix indents and other trivial things
mtd: denali: remove unnecessary parentheses
mtd: denali: remove another set-but-unused variable
mtd: denali: fix include guard and license block of denali.h
mtd: nand: don't break long print messages
mtd: bcm47xxnflash: replace some magic numbers
mtd: bcm47xxnflash: NAND_CMD_RESET support
mtd: bcm47xxnflash: add cmd_ctrl handler
...
Drivers currently call spi_nor_match_id() and then spi_nor_scan().
This adds a dependency on struct spi_device_id which we want to
avoid. Make spi_nor_scan() do it for them.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This simplifies the way we use spi_nor framework and will allow us to
drop spi_nor_match_id.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The MTD_NAND_OMAP_BCH doesn't harm on legacy OMAP platforms
so don't state that it should be disabled for them.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit adds a hidden option to build the omap_elm as a module, if
omap2_nand is a module (and similarly in the built-in case).
This fixes the following build error when omap2_nand is chosen built-in,
and omap_elm is chosen as a module:
drivers/built-in.o: In function `omap_nand_probe':
drivers/mtd/nand/omap2.c:2010: undefined reference to `elm_config'
drivers/mtd/nand/omap2.c:1980: undefined reference to `elm_config'
drivers/mtd/nand/omap2.c:1927: undefined reference to `elm_config'
drivers/built-in.o: In function `omap_elm_correct_data':
drivers/mtd/nand/omap2.c:1444: undefined reference to `elm_decode_bch_error_page'
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Clear QUEUE_FLAG_ADD_RANDOM in all block drivers that set
QUEUE_FLAG_NONROT.
Historically, all block devices have automatically made entropy
contributions. But as previously stated in commit e2e1a148 ("block: add
sysfs knob for turning off disk entropy contributions"):
- On SSD disks, the completion times aren't as random as they
are for rotational drives. So it's questionable whether they
should contribute to the random pool in the first place.
- Calling add_disk_randomness() has a lot of overhead.
There are more reliable sources for randomness than non-rotational block
devices. From a security perspective it is better to err on the side of
caution than to allow entropy contributions from unreliable "random"
sources.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We need to add fm_sb too.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Tanya Brokhman <tlinder@codeaurora.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This "type" seems to be an extra hint for m25p80 about the flash. Some
archs register flash_platform_data with "name" set to "m25p80" and then
with a real flash name set in "type". It seems to be a trick specific
to the m25p80 so let's move it out of spi-nor.
Btw switch to the spi_nor_match_id instead of iterating spi_nor_ids.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Current situation with 4K sectors is quite messy. First of all, some
MTD "users" don't work with such small size. An example may be UBIFS
which requires 15 KiB erase blocks as a minimum. In theory spi-nor
should provide multiple erase regions and MTD "users" should use the
one they need. Unforunately that is not implemented.
In the result our flashes database in spi-nor is hackish. For some
flashes we pretend they don't support 4K sectors just because some
distribution uses UBIFS on it. This ofc leads to conflicts, like
Samsung using w25q128 with 4K sectors vs. OpenWrt requiring it to
pretend it's 64 KiB blocks only.
My idea (plan?) for fixing this situation:
1) Use real hw info (this requires a way for disabling 4K for now)
2) Provide detailed info about erase regions
3) Make UBIFS work with devices that support 4K sectors
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It confused me more than once that the cancel flag of the
work function does not indicate the cancellation of a single work.
In fact it indicates the WL sub-system shutdown and therefore
worker functions have to free their wl_entries too.
That's why you cannot cancel a single work, you can only shutdown
all works.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
There is no need to set err, it will be overwritten in any case
later at:
if (scrub)
err = ubi_wl_scrub_peb(ubi, pnum);
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The while loop in produce_free_peb() assumes that each work will produce a
free PEB. This is not true.
If ubi->works_count is 1 and the only scheduled work is the
wear_leveling_worker() produce_free_peb() can loop forever in case
nobody schedules an erase work.
Fix this issue by checking in the while loop whether work is scheduled.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The ELM driver is only used by the OMAP NAND driver, so let's move it
to the nand/ directory. Additionally, let's rename it to a less confusing
name, so the module is built with a meaningful name, instead of the previous
'elm.ko'.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Usage of pr_err is frowned upon, so replace it with dev_err.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The current code abuses ifdefs to determine if the selected ECC scheme
is supported by the running kernel. As a result the code is hard to read,
and it also fails to load as a module.
This commit removes all the ifdefs and instead introduces a function
omap2_nand_ecc_check() to check if the ECC is supported by using
IS_ENABLED(CONFIG_xxx).
Since IS_ENABLED() is true when a config is =y or =m, this change fixes the
module so it can be loaded with no issues.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the full description of the Hynix H27UCG8T2ATR-BC NAND chip in the
nand_ids table so that we can later use the NAND ECC infos and ONFI timings
mode in controller drivers.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add an onfi_timing_mode_default field to nand_chip and nand_flash_dev in
order to support NAND timings definition for non-ONFI NAND.
NAND that support better timings mode than the default one have to define
a new entry in the nand_ids table.
The default timing mode should be deduced from timings description from
the datasheet and the ONFI specification
(www.onfi.org/~/media/ONFI/specs/onfi_3_1_spec.pdf, chapter 4.15
"Timing Parameters").
You should choose the closest mode that fit the timings requirements of
your NAND chip.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Previously, the only way to map a NOR device as a simple ROM was to
use the obsolete "direct-mapped" compatible binding (which further
requires device_type = "nor" and probe-type = "NOR" properties).
This patch adds an "mtd-rom" compatible binding to the "map_rom"
probe type.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The "ROM" and unknown probe types within the obsolete "direct-mapped"
probe function used the nonexistent "mtd_rom" probe instead of the
intended "map_rom".
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
- Fix indents
- Do not break a line unless it is longer than 80 columns
- Do not insert a whitespace before ';'
- Use whitespaces around operators
- Use braces for a "else" block where the "if" block uses ones.
Besides, eliminate all the warnings reported by checkpatch.pl:
- WARNING: quoted string split across lines
- WARNING: else is not generally useful after a break or return
- WARNING: Missing a blank line after declarations
- WARNING: Avoid line continuations in quoted strings
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We should use parentheses only when they are necessary
or they really improve the readability.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The variable "irq_status" in denali_read_page_raw() is set, but not used.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
I noticed this during a code review. We are checking that the strlen()
of ->name is not less than the ->name_len which the user gave us. I
believe this bug is harmless but clearly we meant to return here instead
of setting an error code and then not using it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
It looks like this header file is a concatenation of two headers.
Anyway, the include guard should be renamed and placed at the correct
postion and the license block in the middle should be deleted.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This follows Chapter 2 of Linux's CodingStyle:
> However, never break user-visible strings such as printk messages,
> because that breaks the ability to grep for them.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This won't be used by NAND subsystem as we implement cmdfunc on our
own, but will allow us to write a bit cleaner code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We are supposed to mask value, not multiply it. Add some comments btw.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Old devices used to have NVRAM at the very end of flash and they could
be unaligned (starting at some offset in a block).
In new devices NVRAM can be located quite randomly, however it seems to
always start at the beginning of a block. For example Netgear R6250 has
NVRAM located right after the bootloader, before the kernel partition.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
For PMECC, the pmecc_bytes_per_sector has same meaning as ecc.bytes.
So remove pmecc_bytes_per_sector and use ecc.bytes instead.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
For PMECC, the pmecc_sector_number has same meaning as ecc.steps.
So use ecc.steps to replace the pmecc_sector_number.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit adds a new platform-data boolean property that enables use
of a flash-based bad block table. This can also be enabled by setting
the 'nand-on-flash-bbt' devicetree property.
If the flash BBT is not enabled, the driver falls back to use OOB
bad block markers only, as before. If the flash BBT is enabled the
kernel will keep track of bad blocks using a BBT, in addition to
the OOB markers.
As explained by Brian Norris the reasons for using a BBT are:
""
The primary reason would be that NAND datasheets specify it these days.
A better argument is that nobody guarantees that you can write a
bad block marker to a worn out block; you may just get program failures.
This has been acknowledged by several developers over the last several
years.
Additionally, you get a boot-time performance improvement if you only
have to read a few pages, instead of a page or two from every block on
the flash.
""
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Retrieve the NFC clock to make sure it is enabled. Make that optional to ensure
compatibility with previous device trees but document it as mandatory so newer
device trees will include it.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The UBI_IOCVOLUP ioctl is used to start an update and also to
truncate a volume. In the first case, a "volume updated" notification
is dispatched when the update is done.
This commit adds the "volume updated" notification to be also sent when
the volume is truncated. This is required for UBI block and gluebi to get
notified about the new volume size.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@vger.kernel.org # v3.15+
Static volumes can change its 'used_bytes' when they get updated,
and so the block interface must listen to the UBI_VOLUME_UPDATED
notification to resize the block device accordingly.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@vger.kernel.org # v3.15+
We are currently taking the block device size from the ubi_volume_info.size
field. However, this is not the amount of data in the volume, but the
number of reserved physical eraseblocks, and hence leads to an incorrect
representation of the volume.
In particular, this produces I/O errors on static volumes as the block
interface may attempt to read unmapped PEBs:
$ cat /dev/ubiblock0_0 > /dev/null
UBI error: ubiblock_read_to_buf: ubiblock0_0 ubi_read error -22
end_request: I/O error, dev ubiblock0_0, sector 9536
Buffer I/O error on device ubiblock0_0, logical block 2384
[snip]
Fix this by using the ubi_volume_info.used_bytes field which is set to the
actual number of data bytes for both static and dynamic volumes.
While here, improve the error message to be less stupid and more useful:
UBI error: ubiblock_read_to_buf: ubiblock0_1 ubi_read error -9 on LEB=0, off=15872, len=512
It's worth noticing that the 512-byte sector representation of the volume
is only correct if the volume size is multiple of 512-bytes. This is true for
virtually any NAND device, given eraseblocks and pages are 512-byte multiple
and hence so is the LEB size.
Artem: tweak the error message and make it look more like other UBI error
messages.
Fixes: 9d54c8a33e ("UBI: R/O block driver on top of UBI volumes")
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@vger.kernel.org # v3.15+
commit 4df38926f3 ("UBI: block: Avoid disk size integer overflow")
introduced a dereference on dev (which is not initialized at that
point) when printing a warning message. Re-order disk_capacity check
after the dev is found.
Found by cppcheck:
[drivers/mtd/ubi/block.c:509]: (error) Uninitialized variable: dev
Artem: tweak the error message a bit
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
I ran into this error after a ubiupdatevol, because I forgot to backport
e9110361a9 UBI: fix the volumes tree sorting criteria.
UBI error: process_pool_aeb: orphaned volume in fastmap pool
UBI error: ubi_scan_fastmap: Attach by fastmap failed, doing a full scan!
kmem_cache_destroy ubi_ainf_peb_slab: Slab cache still has objects
CPU: 0 PID: 1 Comm: swapper Not tainted 3.14.18-00053-gf05cac8dbf85 #1
[<c000d298>] (unwind_backtrace) from [<c000baa8>] (show_stack+0x10/0x14)
[<c000baa8>] (show_stack) from [<c01b7a68>] (destroy_ai+0x230/0x244)
[<c01b7a68>] (destroy_ai) from [<c01b8fd4>] (ubi_attach+0x98/0x1ec)
[<c01b8fd4>] (ubi_attach) from [<c01ade90>] (ubi_attach_mtd_dev+0x2b8/0x868)
[<c01ade90>] (ubi_attach_mtd_dev) from [<c038b510>] (ubi_init+0x1dc/0x2ac)
[<c038b510>] (ubi_init) from [<c0008860>] (do_one_initcall+0x94/0x140)
[<c0008860>] (do_one_initcall) from [<c037aadc>] (kernel_init_freeable+0xe8/0x1b0)
[<c037aadc>] (kernel_init_freeable) from [<c02730ac>] (kernel_init+0x8/0xe4)
[<c02730ac>] (kernel_init) from [<c00093f0>] (ret_from_fork+0x14/0x24)
UBI: scanning is finished
Freeing the cache in the error path fixes the Slab error.
Tested on at91sam9g35 (3.14.18+fastmap backports)
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable <stable@vger.kernel.org> # 3.10+
The variable "retry" in wait_for_irq() is set, but not used.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We should rathar use "int" type for loop iterators.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Useless casts result in unreadable source code.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
All of these variables are initialized to zero and then
set to a different value below.
Zero-initializing is redundant.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We should use
/*
* Blah Blah ...
* ...
*/
for multi-line comment blocks.
In addition, refactor some comments where it seems reasonable and
remove some comments where the code is clear enough such as:
/* clear interrupts */
clear_interrupts(denali);
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* A tiny comment tweak, to kill a bunch of DocBook warnings added during the
merge window
* A small fixup to the OTP routines' error handling
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7uT9
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20140905' of git://git.infradead.org/linux-mtd
Pull mtd fixes from Brian Norris:
"Two trivial MTD updates for 3.17-rc4:
- a tiny comment tweak, to kill a bunch of DocBook warnings added
during the merge window
- a small fixup to the OTP routines' error handling"
* tag 'for-linus-20140905' of git://git.infradead.org/linux-mtd:
mtd: nand: fix DocBook warnings on nand_sdr_timings doc
mtd: cfi_cmdset_0002: check return code for get_chip()
commit 65b97cf6b8 introduced in v3.7 caused a regression
by using a reversed CS_MASK thus causing omap_calculate_ecc to
always fail. As the NAND base driver never checks for .calculate()'s
return value, the zeroed ECC values are used as is without showing
any error to the user. However, this won't work and the NAND device
won't be guarded by any error code.
Fix the issue by using the correct mask.
Code was tested on omap3beagle using the following procedure
- flash the primary bootloader (MLO) from the kernel to the first
NAND partition using nandwrite.
- boot the board from NAND. This utilizes OMAP ROM loader that
relies on 1-bit Hamming code ECC.
Fixes: 65b97cf6b8 (mtd: nand: omap2: handle nand on gpmc)
Cc: <stable@vger.kernel.org> [3.7+]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For v3.12 and prior, 1-bit Hamming code ECC via software was the
default choice. Commit c66d039197 in v3.13 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.
This ECC layout change causes NAND filesystems created in v3.12
and prior to be unusable in v3.13 and later. So revert back to
using software ECC by default if an ECC scheme is not explicitely
specified.
This defect can be observed on the following boards during legacy boot
-omap3beagle
-omap3touchbook
-overo
-am3517crane
-devkit8000
-ldp
-3430sdp
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It's a one-liner doing no magic and its name may be confusing because
it does not have to use JEDEC (e.g. when using alternative read_id).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix the bug in handling gpio flash read/write when offset + len
from MTD exceeds the window size
Signed-off-by: Aaron Wu <Aaron.wu@analog.com>
[Brian: made some commentary edits. Also note that the BUG_ON() was
provably false for all non-negative inputs (since x % y <= x), so we
dropped it.]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
drivers/mtd/nand/nand_timings.c:45: warning: integer constant is too large for ‘long’ type
[ Editorial note: This is a false warning. Looking at ISO draft N1124
(this is approximately C11, the first PDF I had lying around),
section 6.4.4.1 (statement 5):
"The type of an integer constant is the first of the
corresponding list in which its value can be represented."
So this should not be an overflow, and any toolchain that says so
(e.g., GCC 4.4) is buggy.
-Brian ]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When enable NFC sram write, it will failed the mtd_nandbiterrs.ko test.
As in driver's nfc_sram_write_page(), if ops->mode equal to MTD_OSP_RAW,
driver assumes the data buffer contains one page data and one oob data
followed. And driver will write the page data and oob data to nand.
But this is wrong implementation. Since the data buffer don't contains the
oob data to write. We should write the chip->oob_poi to nand's oob.
So this patch fix it by writing the oob data from chip->oob_poi.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
chip->pagebuf is a 32-bit type (int), so the shift will only be applied
as 32-bit. Fix this for 64-bit safety.
Caught by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The condition "if (irq_status == 0)" already ensures that one half of
the ternary ?: is dead. I think this should probably actually be a FAIL,
not a PASS.
Caught by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Jamie Iles <jamie@jamieiles.com>
These multiplications are done with 32-bit arithmetic, then converted to
64-bit. We should widen the integers first to prevent overflow. This
could be a problem for large (>4GB) MTD's.
Detected by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
MTD used to allow compiling out character device support. This was
dropped in the following commit, but some of the accompanying logic was
never dropped:
commit 660685d9d1
Author: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Date: Thu Mar 14 13:27:40 2013 +0200
mtd: merge mtdchar module with mtdcore
The weird logic was flagged by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
There is one theoretical case that could fall through to using an
uninitialized value as the return code. Let's give it a value of 0.
Untested.
Caught by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When checking the upper boundary (i.e., whether an address is higher
than the maximum size of the MTD), we should be doing an inclusive check
(greater or equal). For instance, an address of 16MB (0x1000000) on a
16MB device is invalid.
The strengthening of this bounds check is redundant for those which
already have a address+length check and ensure that the length is
non-zero, but let's just fix them all, for completeness.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The variable 'retries' is never modified, so if the reset operation
never is going to complete, we'll get stuck in an infinite loop.
It looks like the intention was to decrement 'retries' on every loop.
Untested.
Caught by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Do nand reset before write protect check.
If we want to check the WP# low or high through STATUS READ and check bit 7,
we must reset the device, other operation (eg.erase/program a locked block) can
also clear the bit 7 of status register.
As we know the status register can be refreshed, if we do some operation to trigger it,
for example if we do erase/program operation to one block that is locked, then READ STATUS,
the bit 7 of READ STATUS will be 0 indicate the device in write protect, then if we do
erase/program operation to another block that is unlocked, the bit 7 of READ STATUS will
be 1 indicate the device is not write protect.
Suppose we checked the bit 7 of READ STATUS is 0 then judge the WP# is low (write protect),
but in this case the WP# maybe high if we do erase/program operation to a locked block,
so we must reset the device if we want to check the WP# low or high through STATUS READ and
check bit 7.
Signed-off-by: White Ding <bpqw@micron.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fixed checkpatch warnings: "WARNING: Prefer seq_puts to seq_printf"
This patch is created with reference to the ongoing lkml thread
https://lkml.org/lkml/2014/7/15/646
where Andrew Morton wrote:
"
- puts is presumably faster
- puts doesn't go rogue if you accidentally pass it a "%".
- this patch would actually make compiled object files few bytes smaller.
Perhaps because seq_printf() is a varargs function, forcing the
caller to pass args on the stack instead of in registers.
"
Signed-off-by: Samarth Parikh <samarthp@ymail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
MAP10 command with '0x2000' data sets up a read-ahead/write access.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit adds the support in the spi-nor driver of the Micron
M25PX80 flash, a 8 Mbit SPI flash from Micron.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
PMECC can support 512, 1k, 2k, 4k, 8k page size.
The driver currently only support 2k page size nand flash. So this patch
add support to 512, 1k, 4k and 8k page size nand flash.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some nand with 8k page size like Micron MT29F32G08ABAAAWP need more than 20us.
Signed-off-by: Raphaël Poggi <poggi.raph@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use NULL instead of 0 when returning an address. This fixes a
sparse warning.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We check "cs" for array overflows but we don't check for underflows and
it upsets the static checkers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
fixes are:
* UBI deleted list items while iterating the list with 'list_for_each_entry'
* The UBI block driver did not work properly with very large UBI volumes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zgqa
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.17-rc1' of git://git.infradead.org/linux-ubifs
Pull UBI/UBIFS changes from Artem Bityutskiy:
"No significant changes, mostly small fixes here and there. The more
important fixes are:
- UBI deleted list items while iterating the list with
'list_for_each_entry'
- The UBI block driver did not work properly with very large UBI
volumes"
* tag 'upstream-3.17-rc1' of git://git.infradead.org/linux-ubifs: (21 commits)
UBIFS: Add log overlap assertions
Revert "UBIFS: add a log overlap assertion"
UBI: bugfix in ubi_wl_flush()
UBI: block: Avoid disk size integer overflow
UBI: block: Set disk_capacity out of the mutex
UBI: block: Make ubiblock_resize return something
UBIFS: add a log overlap assertion
UBIFS: remove unnecessary check
UBIFS: remove mst_mutex
UBIFS: kernel-doc warning fix
UBI: init_volumes: Ignore volumes with no LEBs
UBIFS: replace seq_printf by seq_puts
UBIFS: replace count*size kzalloc by kcalloc
UBIFS: kernel-doc warning fix
UBIFS: fix error path in create_default_filesystem()
UBIFS: fix spelling of "scanned"
UBIFS: fix some comments
UBIFS: remove useless @ecc in struct ubifs_scan_leb
UBIFS: remove useless statements
UBIFS: Add missing break statements in dbg_chk_pnode()
...
AMD-compatible CFI driver:
- Support OTP programming for Micron M29EW family
- Increase buffer write timeout, according to detected flash parameter info
NAND
- Add helpers for retrieving ONFI timing modes
- GPMI: provide option to disable bad block marker swapping (required for
Ka-On electronics platforms)
SPI NOR
- EON EN25QH128 support
- Support new Flag Status Register (FSR) on a few Micron flash
Common
- New sysfs entries for bad block and ECC stats
And a few miscellaneous refactorings, cleanups, and driver improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Wkmz
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20140808' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"AMD-compatible CFI driver:
- Support OTP programming for Micron M29EW family
- Increase buffer write timeout, according to detected flash
parameter info
NAND
- Add helpers for retrieving ONFI timing modes
- GPMI: provide option to disable bad block marker swapping (required
for Ka-On electronics platforms)
SPI NOR
- EON EN25QH128 support
- Support new Flag Status Register (FSR) on a few Micron flash
Common
- New sysfs entries for bad block and ECC stats
And a few miscellaneous refactorings, cleanups, and driver
improvements"
* tag 'for-linus-20140808' of git://git.infradead.org/linux-mtd: (31 commits)
mtd: gpmi: make blockmark swapping optional
mtd: gpmi: remove line breaks from error messages and improve wording
mtd: gpmi: remove useless (void *) type casts and spaces between type casts and variables
mtd: atmel_nand: NFC: support multiple interrupt handling
mtd: atmel_nand: implement the nfc_device_ready() by checking the R/B bit
mtd: atmel_nand: add NFC status error check
mtd: atmel_nand: make ecc parameters same as definition
mtd: nand: add ONFI timing mode to nand_timings converter
mtd: nand: define struct nand_timings
mtd: cfi_cmdset_0002: fix do_write_buffer() timeout error
mtd: denali: use 8 bytes for READID command
mtd/ftl: fix the double free of the buffers allocated in build_maps()
mtd: phram: Fix whitespace issues
mtd: spi-nor: add support for EON EN25QH128
mtd: cfi_cmdset_0002: Add support for locking OTP memory
mtd: cfi_cmdset_0002: Add support for writing OTP memory
mtd: cfi_cmdset_0002: Invalidate cache after entering/exiting OTP memory
mtd: cfi_cmdset_0002: Add support for reading OTP
mtd: spi-nor: add support for flag status register on Micron chips
mtd: Account for BBT blocks when a partition is being allocated
...
This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 3.17. It contains:
- misc Cavium Octeon, BCM47xx, BCM63xx and Alchemy updates
- MIPS ptrace updates and cleanups
- various fixes that will also go to -stable
- a number of cleanups and small non-critical fixes.
- NUMA support for the Loongson 3.
- more support for MSA
- support for MAAR
- various FP enhancements and fixes"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (139 commits)
MIPS: jz4740: remove unnecessary null test before debugfs_remove
MIPS: Octeon: remove unnecessary null test before debugfs_remove_recursive
MIPS: ZBOOT: implement stack protector in compressed boot phase
MIPS: mipsreg: remove duplicate MIPS_CONF4_FTLBSETS_SHIFT
MIPS: Bonito64: remove a duplicate define
MIPS: Malta: initialise MAARs
MIPS: Initialise MAARs
MIPS: detect presence of MAARs
MIPS: define MAAR register accessors & bits
MIPS: mark MSA experimental
MIPS: Don't build MSA support unless it can be used
MIPS: consistently clear MSA flags when starting & copying threads
MIPS: 16 byte align MSA vector context
MIPS: disable preemption whilst initialising MSA
MIPS: ensure MSA gets disabled during boot
MIPS: fix read_msa_* & write_msa_* functions on non-MSA toolchains
MIPS: fix MSA context for tasks which don't use FP first
MIPS: init upper 64b of vector registers when MSA is first used
MIPS: save/disable MSA in lose_fpu
MIPS: preserve scalar FP CSR when switching vector context
...
This patch changes the static memory controller registers to offsets
from base, prefixes them with AU1000_ to avoid silent failures due to
changed addresses and introduces helpers to access them.
No functional changes, comparing assembly of a few select functions shows
no differences.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7463/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the _safe variant because we're iterating over a list where items get
deleted and freed.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch fixes the issue that on very large UBI volumes
UBI block does not work correctly.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
There's no need to set the disk capacity with the mutex held, so this
commit takes the variable setting out of the mutex. This simplifies
the disk capacity fix for very large volumes in a follow up commit.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Currently, ubiblock_resize() can fail if the device is not found
in the list. This commit changes the return type, so the function can
return something meaningful on error paths.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
With a flash-based BBT there is no reason to move the Factory Bad
Block Marker from the data area buffer (to where it is mapped by the
GPMI NAND controller) to the OOB buffer. Thus, make this feature
configurable via DT. This is required for the Ka-Ro electronics
platforms.
In the original code 'this->swap_block_mark' was synonymous with
'!GPMI_IS_MX23()', so use the latter at the relevant places.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix the following error, which sometimes happens during the NFC data
transfer:
atmel_nand 80000000.nand: Time out to wait for interrupt: 0x00010000
atmel_nand 80000000.nand: something wrong, No XFR_DONE interrupt comes.
The root cause is that in the interrupt handler, we read the ISR but
only handle one interrupt. If more than one interrupt arrive at the same
time, then the second one will be lost.
During the NFC data transfer. Two NFC interrupts (NFC_CMD_DONE and
NFC_XFR_DONE) may come at the same time.
NFC_CMD_DONE means NFC command is sent, and NFC_XFR_DONE means NFC data
is transferred.
This patch can handle multiple NFC interrupts at the same time. During
the NFC data transfer, we need to wait for two NFC interrupts:
NFC_CMD_DONE and NFC_XFR_DONE.
Also we separate the completion initialization code to a
nfc_prepare_interrupt(), which is paired with nfc_wait_interrupt().
We call nfc_prepare_interrupt() before sending out nfc commands, to make
sure no interrupt lost.
Reported-by: Matthieu CRAPET <Matthieu.CRAPET@ingenico.com>
Tested-by: Matthieu Crapet <Matthieu.Crapet@ingenico.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In nfc_device_ready(), it's more reasonable to check R/B bit in NFC_SR
than waiting for the R/B interrupt. It cost less time.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Tested-by: Matthieu Crapet <Matthieu.Crapet@ingenico.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add a new function to read the NFC status. Meantime, this function will
check if there is any errors in NFC.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Tested-by: Matthieu Crapet <Matthieu.Crapet@ingenico.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If the ecc parameter is not the same as definition, when the
mtd core check these parameters, it will give the error result.
Take the following as an example:
Calculate how many bits can be corrected in one page.
According to the ecc parameters definition,
one page correct bits = (mtd->writesize * ecc->strength) / ecc->size
take the following use case as an example:
mtd->writesize = 2048 bytes
ecc->strength = 4 bytes (for 512 bytes)
before this patch, the ecc->size = 2048, so the result is 4 bytes.
after this patch, the ecc->size = 512, so the result is 16 bytes.
So, align the ecc parameters the same as definition to correct
this kind of error.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add a converter to retrieve NAND timings from an ONFI NAND timing mode.
At the moment, only SDR NAND timings are supported.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
UBI assumes that ubi_attach_info will only contain ubi_ainf_volume
structures for volumes with at least one LEB.
In scanning mode this is true because UBI can nicely create a ubi_ainf_volume
on demand while creating the EBA table.
For fastmap this is not true, the fastmap on-flash structure has a list of
all volumes, the ubi_ainf_volume structures are created from this list.
So it can happen that an empty volume ends up in init_volumes().
We can easely deal with that by looking into ->leb_count too.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
1. Fix UBI fastmap support which we broke in 3.16-rc1 by reversing the
volumes RB-tree sorting criteria.
2. Make sure that we scrub all PEBs where we see bit-flips - we were missing
some of them when the fastmap feature was enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9bjU
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.16-rc6' of git://git.infradead.org/linux-ubifs
Pull UBI fixes from Artem Bityutskiy:
"Two UBI fastmap-related fixes for v3.16:
- fix UBI fastmap support which we broke in 3.16-rc1 by reversing the
volumes RB-tree sorting criteria.
- make sure that we scrub all PEBs where we see bit-flips - we were
missing some of them when the fastmap feature was enabled"
* tag 'upstream-3.16-rc6' of git://git.infradead.org/linux-ubifs:
UBI: fastmap: do not miss bit-flips
UBI: fix the volumes tree sorting criteria
For some NOR flashes, the size of the buffer program has been increased
from 256 bytes to 512 bytes, and so 2ms maximum timeout can may not be
sufficient for all different vendor's NOR flash. There is maximum
timeout information in the CFI area, so we instead of picking a fixed
value, we can calculate this according to the standard CFI parameters
parsed at probe time. If we haven't probed this information, or it is
smaller than 2000us, then specify a minimum value 2000us.
Tested with Micron JS28F512M29EWx and Micron MT28EW512ABA flash devices.
Signed-off-by: Bean Huo <beanhuo@outlook.com>
[Brian: fix up comments, use 'max()']
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The return value from 'ubi_io_read_ec_hdr()' was stored in 'err', not in 'ret'.
This fix makes sure Fastmap-enabled UBI does not miss bit-flip while reading EC
headers, events and scrubs the affected PEBs.
This issue was reported by Coverity Scan.
Artem: improved the commit message.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The Denali NAND driver reads only 5 bytes of ID, but some Hynix and Samsung
have size parameters in the 6th byte. As a result, the page and oob size
for a Hynix H27UAG8T2B were calculated incorrectly and the driver failed to
load.
The solution is to read 8 bytes of ID, as expected by the NAND framework.
Signed-off-by: Graham Moore <grmoore@altera.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
I got the following panic on my fsl p5020ds board.
Unable to handle kernel paging request for data at address 0x7375627379737465
Faulting instruction address: 0xc000000000100778
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=24 CoreNet Generic
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.15.0-next-20140613 #145
task: c0000000fe080000 ti: c0000000fe088000 task.ti: c0000000fe088000
NIP: c000000000100778 LR: c00000000010073c CTR: 0000000000000000
REGS: c0000000fe08aa00 TRAP: 0300 Not tainted (3.15.0-next-20140613)
MSR: 0000000080029000 <CE,EE,ME> CR: 24ad2e24 XER: 00000000
DEAR: 7375627379737465 ESR: 0000000000000000 SOFTE: 1
GPR00: c0000000000c99b0 c0000000fe08ac80 c0000000009598e0 c0000000fe001d80
GPR04: 00000000000000d0 0000000000000913 c000000007902b20 0000000000000000
GPR08: c0000000feaae888 0000000000000000 0000000007091000 0000000000200200
GPR12: 0000000028ad2e28 c00000000fff4000 c0000000007abe08 0000000000000000
GPR16: c0000000007ab160 c0000000007aaf98 c00000000060ba68 c0000000007abda8
GPR20: c0000000007abde8 c0000000feaea6f8 c0000000feaea708 c0000000007abd10
GPR24: c000000000989370 c0000000008c6228 00000000000041ed c0000000fe00a400
GPR28: c00000000017c1cc 00000000000000d0 7375627379737465 c0000000fe001d80
NIP [c000000000100778] .__kmalloc_track_caller+0x70/0x168
LR [c00000000010073c] .__kmalloc_track_caller+0x34/0x168
Call Trace:
[c0000000fe08ac80] [c00000000087e6b8] uevent_sock_list+0x0/0x10 (unreliable)
[c0000000fe08ad20] [c0000000000c99b0] .kstrdup+0x44/0x90
[c0000000fe08adc0] [c00000000017c1cc] .__kernfs_new_node+0x4c/0x130
[c0000000fe08ae70] [c00000000017d7e4] .kernfs_new_node+0x2c/0x64
[c0000000fe08aef0] [c00000000017db00] .kernfs_create_dir_ns+0x34/0xc8
[c0000000fe08af80] [c00000000018067c] .sysfs_create_dir_ns+0x58/0xcc
[c0000000fe08b010] [c0000000002c711c] .kobject_add_internal+0xc8/0x384
[c0000000fe08b0b0] [c0000000002c7644] .kobject_add+0x64/0xc8
[c0000000fe08b140] [c000000000355ebc] .device_add+0x11c/0x654
[c0000000fe08b200] [c0000000002b5988] .add_disk+0x20c/0x4b4
[c0000000fe08b2c0] [c0000000003a21d4] .add_mtd_blktrans_dev+0x340/0x514
[c0000000fe08b350] [c0000000003a3410] .mtdblock_add_mtd+0x74/0xb4
[c0000000fe08b3e0] [c0000000003a32cc] .blktrans_notify_add+0x64/0x94
[c0000000fe08b470] [c00000000039b5b4] .add_mtd_device+0x1d4/0x368
[c0000000fe08b520] [c00000000039b830] .mtd_device_parse_register+0xe8/0x104
[c0000000fe08b5c0] [c0000000003b8408] .of_flash_probe+0x72c/0x734
[c0000000fe08b750] [c00000000035ba40] .platform_drv_probe+0x38/0x84
[c0000000fe08b7d0] [c0000000003599a4] .really_probe+0xa4/0x29c
[c0000000fe08b870] [c000000000359d3c] .__driver_attach+0x100/0x104
[c0000000fe08b900] [c00000000035746c] .bus_for_each_dev+0x84/0xe4
[c0000000fe08b9a0] [c0000000003593c0] .driver_attach+0x24/0x38
[c0000000fe08ba10] [c000000000358f24] .bus_add_driver+0x1c8/0x2ac
[c0000000fe08bab0] [c00000000035a3a4] .driver_register+0x8c/0x158
[c0000000fe08bb30] [c00000000035b9f4] .__platform_driver_register+0x6c/0x80
[c0000000fe08bba0] [c00000000084e080] .of_flash_driver_init+0x1c/0x30
[c0000000fe08bc10] [c000000000001864] .do_one_initcall+0xbc/0x238
[c0000000fe08bd00] [c00000000082cdc0] .kernel_init_freeable+0x188/0x268
[c0000000fe08bdb0] [c0000000000020a0] .kernel_init+0x1c/0xf7c
[c0000000fe08be30] [c000000000000884] .ret_from_kernel_thread+0x58/0xd4
Instruction dump:
41bd0010 480000c8 4bf04eb5 60000000 e94d0028 e93f0000 7cc95214 e8a60008
7fc9502a 2fbe0000 419e00c8 e93f0022 <7f7e482a> 39200000 88ed06b2 992d06b2
---[ end trace b4c9a94804a42d40 ]---
It seems that the corrupted partition header on my mtd device triggers
a bug in the ftl. In function build_maps() it will allocate the buffers
needed by the mtd partition, but if something goes wrong such as kmalloc
failure, mtd read error or invalid partition header parameter, it will
free all allocated buffers and then return non-zero. In my case, it
seems that partition header parameter 'NumTransferUnits' is invalid.
And the ftl_freepart() is a function which free all the partition
buffers allocated by build_maps(). Given the build_maps() is a self
cleaning function, so there is no need to invoke this function even
if build_maps() return with error. Otherwise it will causes the
buffers to be freed twice and then weird things would happen.
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix various whitespace issues.
No functional changes.
Signed-off-by: Rob Ward <robert.ward114@googlemail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This family of chips was long ago supported by the pre-cfi driver.
CFI code tested on several Zaurus SL-5500 (Collie) 2x16 on 32 bit bus.
Function is_LH28F640BF() mimics is_m29ew() from cmdset_0002.c
Buffer write fixes as seen in 2007 patch c/o
Anti Sullin <anti.sullin <at> artecdesign.ee>
http://comments.gmane.org/gmane.linux.ports.arm.kernel/36733
[Brian: this patch is semi-urgent, because the following patch switches
to using CFI detection for a chip which (until now) is unsupported by
the CFI driver
9218310 ARM: 8084/1: sa1100: collie: revert back to cfi_probe
]
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In commit 67a9ad9b8a ("mtd: nand: Warn the user if the selected ECC
strength is too weak"), a check was added to inform the user when the
ECC used for a NAND device is weaker than the recommended ECC
advertised by the NAND chip. However, the warning uses WARN_ON(),
which has two undesirable side-effects:
- It just prints to the kernel log the fact that there is a warning
in this file, at this line, but it doesn't explain anything about
the warning itself.
- It dumps a stack trace which is very noisy, for something that the
user is most likely not able to fix. If a certain ECC used by the
kernel is weaker than the advertised one, it's most likely to make
sure the kernel uses an ECC that is compatible with the one used by
the bootloader, and changing the bootloader may not necessarily be
easy. Therefore, normal users would not be able to do anything to
fix this very noisy warning, and will have to suffer from it at
every kernel boot. At least every time I see this stack trace in my
kernel boot log, I wonder what new thing is broken, just to realize
that it's once again this NAND ECC warning.
Therefore, this commit turns:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at /home/thomas/projets/linux-2.6/drivers/mtd/nand/nand_base.c:4051 nand_scan_tail+0x538/0x780()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.16.0-rc3-dirty #4
[<c000e3dc>] (unwind_backtrace) from [<c000bee4>] (show_stack+0x10/0x14)
[<c000bee4>] (show_stack) from [<c0018180>] (warn_slowpath_common+0x6c/0x8c)
[<c0018180>] (warn_slowpath_common) from [<c001823c>] (warn_slowpath_null+0x1c/0x24)
[<c001823c>] (warn_slowpath_null) from [<c02c50cc>] (nand_scan_tail+0x538/0x780)
[<c02c50cc>] (nand_scan_tail) from [<c0639f78>] (orion_nand_probe+0x224/0x2e4)
[<c0639f78>] (orion_nand_probe) from [<c026da00>] (platform_drv_probe+0x18/0x4c)
[<c026da00>] (platform_drv_probe) from [<c026c1f4>] (really_probe+0x80/0x218)
[<c026c1f4>] (really_probe) from [<c026c47c>] (__driver_attach+0x98/0x9c)
[<c026c47c>] (__driver_attach) from [<c026a8f0>] (bus_for_each_dev+0x64/0x94)
[<c026a8f0>] (bus_for_each_dev) from [<c026bae4>] (bus_add_driver+0x144/0x1ec)
[<c026bae4>] (bus_add_driver) from [<c026cb00>] (driver_register+0x78/0xf8)
[<c026cb00>] (driver_register) from [<c026da5c>] (platform_driver_probe+0x20/0xb8)
[<c026da5c>] (platform_driver_probe) from [<c00088b8>] (do_one_initcall+0x80/0x1d8)
[<c00088b8>] (do_one_initcall) from [<c0620c9c>] (kernel_init_freeable+0xf4/0x1b4)
[<c0620c9c>] (kernel_init_freeable) from [<c049a098>] (kernel_init+0x8/0xec)
[<c049a098>] (kernel_init) from [<c00095f0>] (ret_from_fork+0x14/0x24)
---[ end trace 62f87d875aceccb4 ]---
Into the much shorter, and much more useful:
nand: WARNING: MT29F2G08ABAEAWP: the ECC used on your system is too weak compared to the one required by the NAND chip
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch removes s5pc100 related onenand codes because of no more
support for S5PC100 SoC in mainline.
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for the locking of the one time
programmable (OTP) memory of Micron M29EW devices.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds support for writing the one time programmable (OTP)
memory of Micron M29EW devices.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When the one time programmable (OTP) memory region is entered by
issuing the 0xaa/0x55/0x88 command, the OTP memory occupies the
addresses which are normally used by the first sector of the regular
flash memory. This patch therefore invalidates cache for this
addresses after entering/exiting OTP memory.
This patch also moves the code into separate functions.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The Micron M29EW has a 256 byte one time programmable (OTP) memory.
This patch adds support for reading this memory. This support will be
extended for locking and writing in subsequent patches.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some new Micron flash chips require reading the flag status register to
determine when operations have completed.
Furthermore, chips with multi-die stacks of the 65nm 256Mb QSPI also
require reading the status register before reading the flag status
register.
This patch adds support for the flag status register in the n25q512ax3
and n25q00 Micron QSPI flash chips.
Signed-off-by: Graham Moore <grmoore@altera.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Michal Sojka