we will need it for ath9k_htc, may be other drivers too
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
to reduce difference between ath9k and ath9k_htc
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On older chips, the INI value differ in similar ways as cycpwr_thr1, so
convert it to absolute values as well.
Since the ANI algorithm is different here compared to the old
implementation (fewer steps, controlled at a different point in time),
it makes sense to use values similar to what would be applied for newer
chips, just without relying on INI defaults.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The table was copied from the ANI implementation of AR9300. It assumes
that the INI values contain a baseline value that is usable as reference
from which to increase/decrease based on the noise immunity value.
On older chips, the differences are bigger and especially AR5008/AR9001
are configured to much more sensitive values than what is useful.
Improve ANI behavior by reverting to the absolute values used in the
previous implementation (expressed as a simple formula instead of the
old table).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The primary purpose of this piece of code was to selectively disable
OFDM weak signal detection. The checks for this are elsewhere, and an
earlier commit relaxed the restrictions for older chips, which are more
sensitive to interference.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unify scnprintf calls and include the current OFDM/CCK immunity level.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
qi->tqi_readyTime is written directly to registers that expect
microseconds as unit instead of TU.
When setting the CABQ ready time, cur_conf->beacon_interval is in TU, so
convert it to microseconds before passing it to ath9k_hw.
This should hopefully fix some Tx DMA issues with buffered multicast
frames in AP mode.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since commit 558ff225de (ath9k: fix
ps-poll responses under a-mpdu sessions) non-data frames would have
gotten a sequence number from a TIDs sequence counter instead of
using the global sequence counter.
This can lead to instable connections.
To fix this only select the correct TID if we are processing a
data frame. Furthermore, prevent non-data frames to get a sequence
number from a TID sequence counter by adding a check to
ath_tx_setup_buffer.
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: reduce baseband hang detection false positive rate"
added a delay in the loop checking the baseband state, however it was
unreachable due to previous 'continue' statements.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Seems like we have an old bug, where we incidently overwrites
the max_antenna_gain we pass to firmware, with zero value.
End of all we are artifically reducing the output power.
This patch removes the excessive assignment on max_antenna_gain,
which is being provided by regulatory domain, and consequently
improves the tx power.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Consolidate the list of msdu skbs into the msdu-head skb, delete the
rest of the skbs, pass the msdu-head skb on up the stack as normal.
Tested with high-speed TCP and UDP traffic on modified firmware that
supports raw-rx.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Smatch suggests to propagate error code from wil_find_cid(), and, indeed,
it is a good idea.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wrong index comparison logic, found by smatch:
drivers/net/wireless/ath/wil6210/debugfs.c:402 wil_txdesc_debugfs_show() warn: buffer overflow 'wil->vring_tx' 24 <= 24
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Older chipsets are more sensitive to high PHY error counts, and the
current noise immunity thresholds were based on tests run at QCA with
newer chipsets.
This patch brings back the values from the old ANI implementation for
old chipsets, and it also disables weak signal detection on an earlier
noise immunity level, to improve overall radio stability on affected
devices.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit 80b4205b "ath9k: Fix OFDM weak signal detection for AP mode"
prevented weak signal detection changes from taking effect in AP mode on
all chipsets, claiming it is "not allowed".
The main reason for not disabling weak signal detection in AP mode is
that typically beacon RSSI is used to track whether it is needed to
boost range, and this is unavailable in AP mode for obvious reasons.
The problem with not disabling weak signal detection is that older
chipsets are very sensitive to high PHY error counts. When faced with
heavy noise, this can lead to an excessive amount of "Failed to stop
TX DMA" errors in the field.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to 802.11n-2012 standard in paragraph PPDU Fromat(20.3.2) HT-mixed
format Hearder PPDU contains : L_STF, L_LTF, L_SIG, HT_SIG, HT_STF, HT_LTF
they are symbols in the preamble, there are in time unit(us) that's for why
it can't be computed in bytes
Signed-off-by: Sylvain ROGER RIEUNIER <sylvain.roger.rieunier@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using multiple vdevs (stations, aps, etc), it is
nice to be able to associate log messages with specific
interfaces. So, add vdev-id to most logging messages.
Add return code as well, where it was missing.
kvalo: unify some of the messages to follow the same style
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Groupcast frames are not subject for BACK reordering because they are not
ACK'ed and one can't request re-transmitt
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
implement del_station() method in the struct cfg80211_ops
It allows to disconnect single peer from the AP
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When notifying about Rx mgmt (ex: during scan), extract
signal strength reported by the hardware.
signal is not MBM, it is arbitrary units 0..100
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Need to fill translation table before calling WMI with WMI_VRING_CFG_CMDID
since firmware may generate events during this call; and events need translation
table filled to be properly dispatched
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disconnect event reported by the FW, should lead to disconnection
of only requested peer. Find for the appropriate CID and disconnect
only it
For AP-like interface, notify cfg80211 with del_sta(),
for the client type interface, disconnect and turn link off.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calculate statistics per connection, report with "iw station dump"
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rx stats is not calculated per STA - just give some number
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When FW notifies about BACK status change, it provides ring ID.
Process BA status for requested connection only. As for now, FW
don't report Rx BACK status, it reports Tx one instead.
As per current algorithm used in the firmware, imply Rx BACK
state is in sync with Tx one
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware do not support "real" broadcast on the air.
Use method similar to the Directed Multicast Service (DMS) as
described in the 10.23.15.2 "DMS procedures"
This service copies frame and delivers unicast for each associated peer
Do the following: send original frame to 1-st Tx vring, and send copies
to all other active vrings.
As currently hardware/firmware don't support A-MSDU, convert broadcast
frame to unicast instead of wrapping it in A-MSDU
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are 24 possible Tx vrings; when doind multiple connections, more then
one vring has to be used. Search for free one and select it.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When running multiple connections, hardware can't do BACK reordering
and it should be done on the host.
Model after mac80211's implementation. Drop RCU for now;
to be re-added when BACK will be stabilized
BACK handshaking is not implemented yet in the hardware,
pretend it was done to support the way FW operating
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable multiple (up to 8 - HW/FW limitation) simultaneous connections.
Each connection has its own CID (connection ID) that describes chip's
beam-forming entity. Tx Vring should refer to correct CID for frame to reach
its destination.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Print '_' for the 'idle' descriptors - this makes vring representation more visible.
Also, for the Tx side, differentiate descriptors having associated skb's - print ones
with skb as 'H' and without as 'h'. Good to represent scattered frames.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Expand debug capabilities to query all Tx/Rx descriptors. Usefull to analyse
various hardware/software stall situations. Printed is whole descriptor content
and the frame itself.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement management frame passing. In order to receive frame on the other
side, remain_on_channel() should be implemented as well
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and rename it to ath9k_cmn_setup_ht_cap
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and rename it to ath9k_cmn_init_channels_rates.
sbands are move to ath_common as well.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It doesn't make much sense to calculate the ring
size fill count because it already is memoized in
a separate variable.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
One of the premises was to guarantee serialized
completion handling for upper layers
(HTC/WMI/HTT). Since quite some time now it is no
longer necessary.
The other premise was to batch up tx/rx
completions to take advantage of hot caches.
However frame tx/rx completion indications come in
on a single pipe already so they are already
batched up. More meaningful batching is done in
HTT itself.
This means PCI completion is no longer necessary
to keep around. It just wastes memory, cycles and
SLOC.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is inefficient to grab irqsave spinlocks for
skb lists for each queue/dequeue action.
Using rx_ring.lock and tx_lock allows to use less
heavy bh spinlock functions and moving locking
upwards allows to toggle spinlocks less often.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HTT Rx endpoint processes both frame rx
indications and frame tx completion indications.
Those completions typically come in batches and
may be mixed so it makes sense to defer processing
hoping to get a bunch of them and take advantage
of hot caches.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Going through full htc tx path for htt tx is a
waste of resources. By skipping it it's possible
to easily submit scatter-gather to the pci hif for
reduced host cpu load and improved performance.
The new approach uses dma pool to store the
following metadata for each tx request:
* msdu fragment list
* htc header
* htt tx command
The htt tx command contains a msdu prefetch.
Instead of copying it original mapped msdu address
is used to submit a second scatter-gather item to
hif to make a complete htt tx command.
The htt tx command itself hands over dma mapped
pointers to msdus and completion of the command
itself doesn't mean the frame has been sent and
can be unmapped/freed. This is why htc tx
completion is skipped for htt tx as all tx related
resources are freed upon htt tx completion
indication event (which also implicitly means htt
tx command itself was completed).
Since now each htt tx request effectively consists
of 2 copy engine items CE_HTT_H2T_MSG_SRC_NENTRIES
is updated to allow maximum of
TARGET_10X_NUM_MSDU_DESC msdus being queued. This
keeps the tx path resource management simple.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
PCI is capable of handling scatter-gather lists.
This can be used to avoid copying memory.
Change the name of the callback while at to
reflect its purpose.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The flag wasn't used anymore. No need to keep it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no real benefit from using them. DMA-API
already provides debugging. Some skbuffs are
already mapped directly with DMA-API since wrapper
arguments were insufficient and extending them
would be pointless.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
After we pass frames with INV_PEER to upper layer in commit 716ae53c56
("ath10k: pass frames with invalid peer status to upper layer") we could pass
some management frames (in case INVALID_PEER and MGMT_CTRL) twice to upper
layer, once via WMI and once via HTT. Next we could handle assoc request twice.
This patch remove such regression.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Indicate spectrum management support in hardware
flags, while we already handle power set
(IEEE80211_CONF_CHANGE_POWER) in the ath10k driver.
This enable 802.11h support for station mode.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Retrieve the mactime of ieee80211_rx_status based on received
data frame. The value is obtained from the htt_rx_indication_ppdu
structure and only available in 32-bit.
kvalo: white space fixes
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The arsta structure wasn't initialized for
non-ap interfaces. This should fix related
warnings/crashes.
Reported-By: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The nwifi header is padded to 4 bytes. This wasn't
a problem until one tried to (at least) rx 4addr
frames.
This finally allows managed iface to be used in a
bridge.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Makes it easier to determine why some failures
happened.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Implement the get TSF by simply returning 0 so that IBSS
merging is happening. Otherwise, IBSS nodes that have similar
SSID naming won't merge. This is simply fooling the mac80211
that the TSF in the received beacon is higher than the local TSF.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Only set sc->rx.discard_next to rx_stats->rs_more when actually
discarding the current descriptor.
Also, fix a detection of broken descriptors:
First the code checks if the current descriptor is not done.
Then it checks if the next descriptor is done.
Add a check that afterwards checks the first descriptor again, because
it might have been completed in the mean time.
This fixes a regression introduced in
commit 723e711356
"ath9k: fix handling of broken descriptors"
Cc: stable@vger.kernel.org
Reported-by: Marco André Dinis <marcoandredinis@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check if the baseband state remains stable, and add a small delay
between register reads.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only one channel is returned - the one currently being used.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some chips, baseband watchdog hangs are more common than others, and
the driver has support for handling them.
Interrupts even after a watchdog hang are also quite common, so there's
not much point in spamming the user's logfiles.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
5/10 MHz channel bandwidth is configured via the PLL clock, instead of
the AR_PHY_MODE register. Using that register is AR93xx specific, and
makes the mode incompatible with earlier chipsets.
In some early versions, these flags were apparently applied at the wrong
point in time and thus did not cause connectivity issues, however now
they are causing problems, as pointed out in this OpenWrt ticket:
https://dev.openwrt.org/ticket/14916
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trivially reduces text size too.
$ size drivers/net/wireless/ath/ath9k/debug.o*
text data bss dec hex filename
34436 2528 5128 42092 a46c drivers/net/wireless/ath/ath9k/debug.o.new
34464 2528 5128 42120 a488 drivers/net/wireless/ath/ath9k/debug.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Number of MAC hangs and stuck beacons were missing
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 handles the actual operations, so ath9k can just indicate
support for this. Based on initial tests, this combination seems to
work fine.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When passing tx frames to the U-APSD queue for powersave poll responses,
the ath_atx_tid pointer needs to be passed to ath_tx_setup_buffer for
proper sequence number accounting.
This fixes high latency and connection stability issues with ath9k
running as AP and a few kinds of mobile phones as client, when PS-Poll
is heavily used
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The minimum CCA power threshold values have to be adjusted
for existing cards to be in compliance with new regulations.
Newer cards will make use of the values obtained from EEPROM,
support for this was added earlier. To make sure that cards
that are already in use and don't have proper values in EEPROM,
do not violate regulations, use the initvals instead.
Cc: stable@vger.kernel.org
Reported-by: Jeang Daniel <dyjeong@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: wil6210@qca.qualcomm.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows dynamic changes of bandwidth/nss/smps,
e.g. via ht/vht operation mode change
notification.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware ignores SMPS flags in peer assoc command.
For SMPS to work it is necessary to set peer
parameter after peer assoc command so that tx
chainmask is setup properly.
This should fix packet loss and improve throughput
with stations that have SMPS enabled upon
association.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
I modified Michal's commit c930f744bd ("ath10k: implement channel switching") to return
when vdev_start() fails, but forgot to release conf_mutex.
Found by coccinelle:
>> drivers/net/wireless/ath/ath10k/mac.c:2745:5-11: preceding lock on line 2663
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes a checkpatch warning in ath10k:
drivers/net/wireless/ath/ath10k/mac.c:1636: WARNING: Avoid CamelCase: <regpair->regDmnEnum>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix a checkpatch warning:
drivers/net/wireless/ath/ath10k/debug.h:95: CHECK: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The dtim period sent to FW was 0 because the dtim period
was never set. This caused an incorrect dtim count to be sent in
beacons.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes problems seen with multiple softap clients and reconnecting
softap clients.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is more line with the names of the other members
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3680 has a few registers on other addresses.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After fw caps exchange, print the FW's capabilities.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If wowlan if off mac80211 will stop / start the driver on suspend /
resume. This causes problems on resume since request_firmware is called
from start. Fix this by caching the nv.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some wcnss firmwares the start command can take up to 300ms to
complete. Currently there is a 200ms timeout for SMD command to
complete which causes the start to fail.
Increase the timeout to 500ms. Also improve debug information
regarding SMD command completion time.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Response format is not in the canonical format.
wcn36xx_smd_rsp_status_check cannot be used.
* Save the FW caps in wcn36xx struct for later use.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the original code we shift "AR5K_PHY(256) >> 28" which is zero but
the intent was to shift the return value of ath5k_hw_reg_read() like we
do a couple lines later.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As result deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Oleksij Rempel