SIZEOF_ARRAY is not used (anymore). Besides, ARRAY_SIZE, defined in
include/linux/kernel.h, should be used rather than explicitly coding some
variant of it.
Signed-off-by: Christoph Jaeger <christophjaeger@linux.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reading firmware status register to detect whether firmware is
running or not didn't work 100% reliably. That register was
likely set by firmware itself which means it could not contain
reasonable values until firmware is up and running. Usually it
just worked as some garbage value was returned accidentally but it
appears that in some cases returned garbage value was 0x00 which
was considered "firmware is up and running" by the driver and
firmware loading was skipped leaving device to non-working state.
Fix problem by removing unreliable check and let the driver keep
count whether firmware is loaded or not.
Signed-off-by: Andreas Matthies <a.matthies@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
changeset 768e6dadd7 caused a regression on using mb86a20s
in parallel mode, as the parallel mode selection got
overriden by mb86a20s_init2.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media updates from Mauro Carvalho Chehab:
"This series contain:
- new i2c video drivers: ml86v7667 (video decoder),
ths8200 (video encoder)
- a new video driver for EasyCap cards based on Fushicai USBTV007
- Improved support for OF and embedded systems, with V4L2 async
initialization and a better support for clocks
- API cleanups on the ioctls used by the v4l2 debug tool
- Lots of cleanups
- As usual, several driver improvements and new cards additions
- Revert two changesets that change the minimal symbol rate for
stv0399, as request by Manu
- Update MAINTAINERS and other files to point to my new e-mail"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (378 commits)
MAINTAINERS & ABI: Update to point to my new email
[media] stb0899: restore minimal rate to 5Mbauds
[media] exynos4-is: Correct colorspace handling at FIMC-LITE
[media] exynos4-is: Set valid initial format on FIMC.n subdevs
[media] exynos4-is: Set valid initial format on FIMC-IS-ISP subdev pads
[media] exynos4-is: Fix format propagation on FIMC-IS-ISP subdev
[media] exynos4-is: Set valid initial format at FIMC-LITE
[media] exynos4-is: Fix format propagation on FIMC-LITE.n subdevs
[media] MAINTAINERS: Update S5P/Exynos FIMC driver entry
[media] Documentation: Update driver's directory in video4linux/fimc.txt
[media] exynos4-is: Change fimc-is firmware file names
[media] exynos4-is: Add support for Exynos5250 MIPI-CSIS
[media] exynos4-is: Add Exynos5250 SoC support to fimc-lite driver
[media] exynos4-is: Drop drvdata handling in fimc-lite for non-dt platforms
[media] media: i2c: tvp514x: remove manual setting of subdev name
[media] media: i2c: tvp7002: remove manual setting of subdev name
[media] mem2mem: set missing v4l2_dev pointer
[media] wl128x: add missing struct v4l2_device
[media] tvp514x: Fix init seqeunce
[media] saa7134: Fix sparse warnings by adding __user annotation
...
According with Manu Abraham, stb0899 seek algorithm is broken
for symbol rates bellow to 5Mbauds. So, revert those patches:
55b3318 [media] stb0899: allow minimum symbol rate of 2000000
2eeed77 [media] stb0899: allow minimum symbol rate of 1000000
Requested-by: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is no longer needed since the core now handles this through DBG_G_CHIP_INFO.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
There are a few cases where breaking the code into separate
lines make it worse to read. However, on several places,
breaking it to make checkpatch.pl happier is OK and improves
code readability.
So, break longer lines where that won't cause harm.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
There are several places where: state->var = (some_var)
The parenthesis there are doing nothing but making it
harder to read and breaking the 80 columns soft limits.
Just get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
Almost all 80-col warnings are related to comments. There's
one, however, that it is due to a one-line enum declaration
for enum agc_ctrl_mode.
Break it into one line per enumered data.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
The comments markup language used on Kernel is defined at:
Documentation/kernel-doc-nano-HOWTO.txt
Remove invalid markups from the header file.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
Fixes the following checkpatch.pl warnings:
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(10);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
replace all occurrences of printk(KERN_* by
pr_info/pr_warn/pr_err/pr_debug/pr_cont macros.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
Thare are lots of CamelCase warnings produced by checkpatch.pl.
This weren't fixed at the time the driver got submitted due
to the lack of manpower do to such cleanup.
Now that I have one script that automates this task, cleans
it. That makes the driver almost checkpatch-compliant,
except for 80 column warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
Log10 routine is already defined at dvb_math.h and provides a good
enough approximation for 100 x log10(). So, instead of reinventing
the wheel, use the already existing function.
While here, don't use CamelCase on the function name.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For consistency, it is necessary to use the autodetected inversion
instead of the configured one.
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In non S2 mode, the device is able to autodetect inversion. So
let's store it for tuning to S2 transponders.
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Usually, inversion doesn't change in a system. Storing the last
successful inversion value speeds up tuning of DVB-S2 transponders.
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Looks like product datasheets for tuners containing STB0899 are
suggesting specification for min. symbol rate of 2MS/s.
Some specs found here, all suggesting 2MS/s for min. symbol rate:
Comtech DVBS2-6899
http://comtech.sg1002.myweb.hinet.net/pdf/dvbs2-6899.pdf
TechniSat SkyStar HD2
http://www.scaistar.com/skystar2/skystarhd2.htm
Azurewave AD-SP400
http://www.pulsat.com/products/AzureWave-AD%252dSP400-High-Definition-PC-Card.html
New patch:
This makes minimum symbol rate driver capabilities on par with some
accessible datasheet specifications*, and allows tuning on linux to
transponders that have symbol rate between 2000000-5000000, too.
Patch was tested successfully on Eutelsat 16A transponders that
became reachable with it (2000000 < symbol rate < 5000000):
* DVB/S 12507050 V 2532000 3/4
* DVB/S2 12574000 V 4355000 3/4 8PSK
* DVB/S 12593000 V 2500000 2/3
* DVB/S 12596940 V 2848000 2/3
* DVB/S 12600750 V 2500000 1/2
* DVB/S 12675590 H 4248000 3/4
(*) Datasheet: http://comtech.sg1002.myweb.hinet.net/pdf/dvbs2-6899.pdf
Maximum Symbol Rate
QPSK/LDPC/PCH: 20-30Mbps
8PSK/LDPC/BCH: 10-30Mbps
DVB: 2-45Mbps
^--------- min. symbol rate
Signed-off-by: Zoran Turalija <zoran.turalija@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Throughout the zig-zag-implementations, inversion is taken into
account when reading and writing the CFR register, which contains
the derotator frequency. As swapping IQ signals changes the sign
of that register for example, the idea is to compensate that sign
change by multiplying the register value with the inversion enum
value.
The current enum values 0 and 1 for IQ_SWAP_OFF and IQ_SWAP_ON
don't work in the case IQ_SWAP_OFF, due to the multiplication by
zero (I've only found a single device which actually uses
IQ_SWAP_OFF in it's config).
I've changed the enum values to +1 and -1 to accommodate to the
intended usage.
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It seems that current inversion handling addresses only the signal
routing on the PCB, i. e. IQ signals are either swapped or not.
But when the device is operated in a Satellite Channel Router (SCR)
environment, an additional inversion is required due to the way how
the SCR works. Therefore it makes sense to me to always enable auto
inversion handling and drop the enum value IQ_SWAP_AUTO.
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes minimum symbol rate driver capabilities on par with
windows driver, and allows tuning on linux to transponders that
have symbol rate below 5000000, too.
Patch was tested successfully on Eutelsat 16A transponders that
became reachable with it (1000000 < symbol rate < 5000000):
* DVB/S 12507050 V 2532000 3/4
* DVB/S2 12574000 V 4355000 3/4 8PSK
* DVB/S 12593000 V 2500000 2/3
* DVB/S 12596940 V 2848000 2/3
* DVB/S 12600750 V 2500000 1/2
* DVB/S 12675590 H 4248000 3/4
Signed-off-by: Zoran Turalija <zoran.turalija@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Contrary to the chip's specs, the register's value is signed, so we
need to sign extend the value before using it in calculations like
when determining the offset frequency.
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb-frontends/dib8000.c: In function ‘dib8000_set_frontend’:
drivers/media/dvb-frontends/dib8000.c:3556: warning: ‘ret’ is used uninitialized in this function
Remove the variable and return zero instead.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes check for EPERM in dbg_g/s_register
as this check is already performed by core.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The check if the values for c, h and n are within the range is
always true, as, if one of this values is out of range, the
previous "if" clauses will default to a value within the
range.
That fixes the following warning:
drivers/media/dvb-frontends/dib0090.c: In function 'dib0090_set_EFUSE':
drivers/media/dvb-frontends/dib0090.c:1545:5: warning: comparison is always true due to limited range of data type [-Wtype-limits]
and makes the code easier to read.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb-frontends/dib8000.c: In function 'dib8000_wait_lock':
drivers/media/dvb-frontends/dib8000.c:3972:1: warning: 'value' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/media/dvb-frontends/dib8000.c:2419:6: note: 'value' was declared here
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
isdbt_sb_subchannel is unsigned with 8 bits. So, it will
never be -1. Instead, any value bigger than 13 is invalid.
As is, the current code generates the following warnings:
drivers/media/dvb-frontends/dib8000.c: In function 'dib8000_set_isdbt_common_channel':
drivers/media/dvb-frontends/dib8000.c:2358:3: warning: comparison is always true due to limited range of data type [-Wtype-limits]
drivers/media/dvb-frontends/dib8000.c: In function 'dib8000_tune':
drivers/media/dvb-frontends/dib8000.c:3107:8: warning: comparison is always false due to limited range of data type [-Wtype-limits]
drivers/media/dvb-frontends/dib8000.c:3153:9: warning: comparison is always false due to limited range of data type [-Wtype-limits]
drivers/media/dvb-frontends/dib8000.c:3160:5: warning: comparison is always false
It should also be noticed that ARIB STD-B31, item
"3.15.6.8 Number of segments" at TMCC table defines the
value 15 for unused segment, and 14 as reserved.
So, better to change the check to consider any value
bigger than 13 to mean that sub-channels should be
disabled, fixing the warning and doing the right thing
even if an invalid value is filled by userspace.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dtv_property_cache is used on several places on very long lines.
On all places it is used, a long list of struct reference is done.
Instead of doing it, at the routines where it is used more than once,
replace it by one temporary var. That may help the compiler to
use a better code. It also makes easier to review the code, as the
lines becomes closer to 80 columns, making them a way clearer
to read.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* topic/r820t: (31 commits)
[media] r820t: Don't divide the IF by two
[media] r820t: disable auto gain/VGA setting
[media] rtl2832: Fix IF calculus
[media] r820t: put it into automatic gain mode
[media] r820t: Fix hp_cor filter mask
[media] r820t: fix PLL calculus
[media] r820t: Don't put it in standby if not initialized yet
[media] r820t: avoid rewrite all regs when not needed
[media] r820t: Allow disabling IMR callibration
[media] r820t: add a commented code for GPIO
[media] r820t: add IMR calibrate code
[media] r820t: proper initialize the PLL register
[media] r820t: use usleep_range()
[media] r820t: fix prefix of the r820t_read() function
[media] r820t: split the function that read cached regs
[media] r820t: better report signal strength
[media] r820t: add support for diplexer
[media] r820t: Show the read data in the bit-reversed order
[media] r820t: use the second table for 7MHz
[media] r820t: Invert bits for read ops
...
The intend of this patch is to improve the support of the dib0090 tuner.
The ramp tables have been updated. Also some minor enhancements has been
added (EFUSE and reset).
Signed-off-by: Olivier Grenie <olivier.grenie@parrot.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@parrot.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The intend of this patch is to improve the support of the dib7000p. It is
now possible to set the minimum value for the AGC1. Also, the driver takes
into account the frequency offset introduced in the tuned frequency.
Signed-off-by: Olivier Grenie <olivier.grenie@parrot.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@parrot.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The intend of this patch is to improve the support of the dib8000.
Signed-off-by: Olivier Grenie <olivier.grenie@parrot.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@parrot.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sparse complains that these are "dubious one-bit signed bitfields" and
the comment says it was intended to be 1 and 0 instead of -1 and 0.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Spectrum is inverted. So, we need to invert it when calculating the
value for the IF register
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
DVBT_EN_BBIN should be set on both places where IF is set. So,
move it to a function and call it where needed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
There are some init stuff to be done for each new tuner at the
demod code. Add the code there for r820t.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
Symbol rate ratio were using a rough calculus, as the code was
limited to 32 bits arithmetic. Change it to 64 bits, in order
to better estimate the bandwidth low-pass filter on the demod.
This should reduce the noise and improve reception.
Reported-by: Hans-Peter Jansen <hpj@urpla.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using 'i' for the guard interval temporary var is a bad idea, as
'i' is generally used by "anonymous" indexes.
Let's rename modulation, fec and guard interval temp vars with
a meaningful name, as that makes easier to understand the code
and avoids cut-and-paste types of error.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Dan Carpenter <dan.carpenter@oracle.com>:
Smatch warnings:
drivers/media/dvb-frontends/mb86a20s.c:644 mb86a20s_layer_bitrate() error: buffer overflow 'state->estimated_rate' 3 <= 3
What happens there is that estimate_rate index should be the layer
number, and not the guard interval.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We're using the anonymous 'i' to indicate the layer number
on several places on the driver. That's not good, as some
cut-and-paste type of change might be doing the wrong thing.
So, call it as "layer" everywhere.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using the magic number "3", use NUM_LAYERS macro
on all places that are related to the ISDB-T layers.
This makes the source code a little more readable.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hauppauge Nova-S-Plus DVB-S model 92001 does not lock on horizontal
polarisation. According with the info provided at the BZ, model
92002 does.
The difference is that, on model 92001, the tone select is done via
isl6421, while, on other devices, this is done via cx24123 code.
This patch adds a way to override the demod's set_tone at isl6421
driver. In order to avoid regressions, the override is enabled
only for cx88 Nova S plus model 92001. For all other models and
devices, the set_tone is provided by the demod driver.
Patch originally proposed at bz@9476[1] by Michel Meyers and
John Donoghue but applying the original patch would break support
for all other devices based on isl6421.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=9476
Tested-by: Adam Sampson <ats@offog.org>
Tested-by: Hans-Peter Jansen <hpj@urpla.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
au8522_attach is dependent on CONFIG_DVB_AU8522_DTV, not CONFIG_DVB_AU8522.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that au0828 has been converted to the control framework these
compatilibity ops are no longer needed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Last parameter of function GetLockStatus() isn't used so drop it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changeset 8f3741e accidentally broke the CNR estimation. It should
be calculated as "a + b - c". However, previously, the subtraction
by c only occurred if SNR would be positive, due to a bad binding
to DVBv3 API.
This also fixes the following warning:
drivers/media/dvb-frontends/drxk_hard.c:2556:6: warning: variable 'c' set but not used [-Wunused-but-set-variable]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use register address auto increment to reduce I/O when large
register / values tables are written.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That register is property of demodulator so move it correct place.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Those are demodulator init tables according to used tuner tuner
config. af9033 demod driver does those inits currently and due
to that these duplicate inits could be removed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dumped out from the Windows driver version 12.07.06.1
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dumped out from the Windows driver version 12.07.06.1
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dumped out from the Windows driver version 12.07.06.1
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dumped out from the Windows driver version 12.07.06.1
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dumped out from the Windows driver version 12.07.06.1
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dumped out from the Windows driver version 12.07.06.1
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dumped out from Windows driver version 12.07.06.1, 07/06/2012.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for tuners integrated to the IT9135 and IT9137.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Kconfig entry for "TS2020 based tuners" defaults to modular if
DVB_FE_CUSTOMISE is set. But that Kconfig symbol was replaced with
MEDIA_SUBDRV_AUTOSELECT as of v3.7. So use the new symbol. And negate
the logic, so we are in line with all the similar entries in this file.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The DVBv3 signal strength indicator is bogus: it doesn't range
from 0 to 65535 as it would be expected. Also, 0 means the max
signal strength.
Now that a better way to estimate it was added, use the new
way.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The AZ6007 driver released by Terratec has a better way to
estimate the signal strength, at CtrlSigStrength(). Port it
to the driver.
It should be noticed that there are two parameters there that
are tuner-specific.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original az6007 driver has the code to calculate such
stats. Add it to the driver, reporting them via DVBv5
stats API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
goto err and goto err_gateoff before mutex_lock(&state->internal->demod_lock)
lead to unlock of unheld mutex in stv090x_sleep().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that some devices initialize register 0x2a with different
values, add the calculus formula, instead of hardcoding it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Up to now, the driver was simply assuming TV mode, 13 segs.
Implement the logic to control the ISDB operational mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signal strength is always available. There's no reason to reset
it, as it has its own logic to reset it already.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Always init the frontend when set_frontend is called. The rationale
is: it was noticed that, on some devices, it fails to lock with a
different channel. It seems that some other registers need to be
restored to its initial state, when the channel changes.
As it is better to reset everything, even wasting a few more
miliseconds than to loose channel lock, let's change the logic
to always reset.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the AGC settings present on a newer device.
The initial settings were taken from one of the first devices with
mb86a20s, and there are several reports that this is not working
properly on some places.
So, instead of keeping using it, get the parameters taken from a
newer device. Tests are welcomed.
Tested also with cx231xx PixelView SBTVD Hybrid with no regressions
noticed so far.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
State 9 means TS started to be output, and it should be
associated with FE_HAS_SYNC.
The mb86a20scan get CNR statistics at state 7, when frame sync
is obtained.
As CNR may help to adjust the antenna, provide it earlier.
A latter patch could eventually start outputing MER measures
earlier, but that would require a bigger change, and probably
won't be better than the current way, as the time between
changing from state 8 to 9 is generally lower than the time
to get the stats collected.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of hardcoding a fixed IF frequency of 3.3 MHz, use
the IF frequency provided by the tuner driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are a few debug tests that are shown with dev_err() or
dev_info(). Replace them by dev_dbg().
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The address of a variable is impossible to be null, so we remove the check.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch introduces the use of IS_ENABLED() macro. For example,
replacing:
#if defined(CONFIG_I2C) || (defined(CONFIG_I2C_MODULE) && defined(MODULE))
with:
#if IS_ENABLED(CONFIG_I2C)
All changes made by this patch respect the same replacement pattern.
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sometimes there is a problem when trying to access the non-existing registers
of the second demodulator path on the STV0903.
This change removes the calls in case the driver is used on a STV0903.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The logic that resets the device is wrong. It should be resetting
just the layer that got read. Also, stop is needed before updating
the counters.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The logic that resets the device is wrong. It should be resetting
just the layer that got read. Also, stop is needed before updating
the counters.
While there, rename it, as we'll soon introduce a postBER logic
there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add both per-layer and global block error count and block count,
for PER and UCB measurements.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add Signal/Noise ratio measurement. On this device, a global measure
is taken by the demod. It also provides per-layer CNR measurements,
based on Modulation Error measures (MER).
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do a better job on setting the bit error counters, in order to
have all layer measures to happen in a little less than one
second.
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the methods to read bit error/bit count measurements from
mb86a20s. On ISDB-T devices, those reads are done per layer.
However, as userspace applications may not be aware of that,
add a global measure that will sum the bit errors and bit
counts for each layer, storing them into a global value.
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of providing separate callbacks to read the several FE
stats properties, the better seems to use just one method that will:
- Read lock status;
- Read signal strength;
- if locked, get TMCC data;
- if locked, get DVB statistics.
As the DVB frontend thread will call this read_status callback
on every 3 seconds, and userspace can even call it earlier,
all stats data and layers layout will be updated together if
available, with is a good thing.
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Feng's kbuild test:
From: kbuild test robot <fengguang.wu@intel.com>
Subject: drivers/media/dvb-frontends/mb86a20s.c:706 mb86a20s_attach() error: potential null dereference 'state'. (kzalloc returns null)
Date: Wed, 23 Jan 2013 19:30:43 +0800
commit: f66d81b54d [media] mb86a20s: convert it to use dev_info/dev_err/dev_dbg
drivers/media/dvb-frontends/mb86a20s.c:706 mb86a20s_attach() error: potential null dereference 'state'. (kzalloc returns null)
drivers/media/dvb-frontends/mb86a20s.c:706 mb86a20s_attach() error: we previously assumed 'state' could be null (see line 705)
As, at mb86a20s_attach(), we have an i2c pointer, use it for all printk
messages there, instead of state->i2c.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of having its own set of macros, use the Kernel default
ones for debug, error and info.
While here, do some cleanup on the debug printk's.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Christoph Jaeger