Several audio decoders were just bound as if they were part of
bttv driver. In fact, they are generic enough to be used by other
drivers as well, since they use I2C event bus to communicate.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
when checking the -Wextra signedness warnings issued by gcc 4.1
I came across this one:
drivers/media/video/vivi.c:1001: warning: comparison of unsigned expression < 0 is always false
Since videobuf_reqbufs() returns negative values on errors the current
code does no real error checking since gcc removes the comparison.
This patch fixes this issue by making ret a normal, signed integer.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Several changes at register stuff were done since commit
b45009b028, but I've forgot
to add the copyright line for this. Those changes allowed
cx88 to have multiple tuners, allowing it to support hardware with
separated radio and video tuners. It also allows binding a tuner to an
specific i2c address.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The Coverity checker spotted the following two array overflows.
Registers 0xcc and 0xdc were cached on reg[] array, with only 128 elements,
instead of 256.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx88-alsa can be compiled in (in distro built kernels, for example), but
not used. In those cases, the audio DMA restart is needed for proper sound
on NICAM channels.
This patch enables the DMA restart even with ALSA, but the functions now
check if cx88-alsa is really active.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Although not dangerous, it may allow a normal user with access to a machine
to untune a TV channel.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the FX2 does not reset properly during reboot, it can present an
invalid USB device ID and fail to attach. Prevent this situation
from occuring by resetting the USB part of the card when the PCI part
probes.
Also fix the GPIO configurations so that analog capture will not
inadvertantly reset the USB part.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If an eeprom defined two tuners and they supported more than eight
standards combined (as opposed to each), it would overflow an array.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/video/pvrusb2/pvrusb2-i2c-cmd-v4l2.c: In function 'set_standard':
drivers/media/video/pvrusb2/pvrusb2-i2c-cmd-v4l2.c:33: warning: format '%llx' expects type 'long long unsigned int', but argument 2 has type 'v4l2_std_id'
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
1) It sets LNBDCPol differently based on the card type. Now it should
work properly for both the kworld and geniatech cards.
2) It stops returning an error for the SEC_VOLTAGE_OFF voltage command
(the cx88-dvb level handles the actual voltage on/off, but it still
passes the ioctl down to the cx24123 level, which previously rejected
the OFF as invalid so the ioctl would report failure)
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Yeasah Pell <yeasah@schwide.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tested on x64 with a bttv board. Most Get ioctls are fixed. The only
non-completely working one is VIDIOCGAUDIO. All other IOR ioctls give the
same results on x86_64 and i386 architectures.
Thanks to Alastair Poole <netstar@gatheringofgray.com> for part of this
patch and tests on ppc64.
Signed-off-by: Alastair Poole <netstar@gatheringofgray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch cleans up some whitespace problems after the dvb_attach changes
in cx88-dvb.c and saa7134-dvb.c, and converts some capitalized i2c address
constants to lowercase.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The test in dvb-pll to see if a tuner's PLL responds when attaching fails
on NXT2004 based boards before the firmware is loaded.
This patch allows us to avoid this test by not passing an I2C bus handle to
the dvb_pll_attach routine, just as Chris Pascoe has done for MT352 and
ZL10353 based boards when used in cx88-dvb.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Typical wiring of MT352 and ZL10353 based tuners differs from dvb-pll's
expectation that the PLL is directly accessible. On these boards, the
PLL is actually hidden behind the demodulator, and as such can only be
accessed via the demodulator's interface. It was failing to communicate
with the PLL during an attach test and subsequently not connecting the
tuner ops.
By passing a NULL I2C bus handle to dvb_pll_attach, this accessibility
check can be bypassed. Do this for the affected boards. Also fix a
possible NULL dereference at sleep time, which would otherwise be
exposed by this change.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for Acorp TV134DS and FlyDVB-S cards (both based on
tda10086+tda826x)
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Allow it to be en/disabled
Disable it in < 2.6.17 due to symbol_xxx() bug
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Only devices using > 1 frontend were ported; ones which did not are left
using static binding.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This change causes the pvrusb2 driver to limit horizontal resolution
to be only 720 if 24xxx device hardware is being used. This is a
workaround for an unsolved problem in the driver where if the
resolution is set to something other than 720 the video quality will
be _seriously_ degraded. It only happens on 24xxx devices (29xxx are
unaffected by the problem and unaffected by this change). Once the
problem is finally solved, this small change can be removed.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The internal control implementation in the pvrusb2 driver normally
encodes integer range limits using literal values in a const
structure. This change adds two function pointers, which if not null
will be called through in order to determine integer min / max
values.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 implementation for VIDIOC_[S|TRY]_FMT was hardcoding
limits on the range for allowed resolution, but it would be much
better if we instead just queried the internal control for these
values. This then opens the door for the driver to adjust these
limits based on the detected hardware.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix a few miscellaneous issues in the pvrusb2 driver related to use of
the new mpeg controls. This also should fix problems involving
update of the saa7115 / cx25840 configuration as control changes are made.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A buffer was set just before an if block, and then again in both branches
of the if. Obvious coding error.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for Shenzhen Tungsten Ages Tech TE-DTV-250 OEM for
Swann PCI TV Tuner Card
Signed-off-by: David Bussenschutt <buzz@oska.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for Norwood PCI TV Tuner (non-pro)
Signed-off-by: Peter Naulls <peter@chocky.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds autodetection support for the AverMedia M150-D
blackbird MPEG encoder / analog video capture card.
This board is known to work with the ASUS PVR 416 configuration.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
add initial support for Hauppauge WinTV-HVR3000 TriMode Analog/DVB-S/DVB-T
only analog is working for now
Signed-off-by: Eric Thomas <ethomas@claranet.fr>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since kernel include autoconf.h via command line, those config.h inclusion
can be removed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It is just another Lifeview clone
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The change is just an additional PCI ID
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Analog TV, CVBS, S-video and DVB-T are working,
DVB-S not yet
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The v4l2 API documentation for VIDIOC_ENUMSTD says:
To enumerate all standards applications shall begin at index
zero, incrementing by one until the driver returns EINVAL.
The actual code, however, tests the index this way:
if (index<=0 || index >= vfd->tvnormsize) {
ret=-EINVAL;
So any application which passes in index=0 gets EINVAL right off the bat
- and, in fact, this is what happens to mplayer. So I think the
following patch is called for, and maybe even appropriate for a 2.6.18.x
stable release.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Several DVB modules depends on I2C
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L1 support should be disabled when no CONFIG_VIDEO_V4L1_COMPAT is defined,
to allow checking for broken V4L2 ports. This is very important during the
migration phase for V4L2 API.
However, userspace apps should be capable of using both APIs, since they need
to test at runtime, via VIDIOCGCAP ioctl, if V4L1 is supported. So, when
__KERNEL__ is not defined, those ioctls and corresponding structs should be
visible.
This patch also removes the obsolete defines HAVE_V4L1 and HAVE_V4L2, that
where causing some confusion, and were replaced by CONFIG_VIDEO_V4L1_COMPAT
and CONFIG_VIDEO_V4L2.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The tena_9533_di_pal_ranges use 0x04 instead the original 0x08 for the
UHF (range 2) switching. This is wrong and therefore nothing happens.
Restore tuner_ymec_tvf66t5_b_dff_pal_ranges[] to make the UHF switch
working again.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In bugzilla #6943, Maxim Britov reported:
"I can enable Logitech quickcam support in .config, but it want be compile.
I have to add into drivers/media/video/Makefile:
obj-$(CONFIG_USB_QUICKCAM_MESSENGER) += usbvideo/"
He's right, just enable that driver as module while disabling every other
driver that gets into that directory, nothing will get compiled.
This patch fixes the Makefile.
Signed-off-by: Diego Calleja <diegocg@gmail.com>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Without the LNA these tuners perform very poorly (read 'unwatchable') when
the signal is weak.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Due to a wrong statement order the 'standard' module option didn't
work for 'G' model chips.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx25840_read4 assembled the bytes in the wrong order.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The compat_ioctl support of the pwc driver was dropped during the last update of the driver.
I suppose it was by mistake. If yes here is the patch to restore the support.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@looxix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A previous patch changed VBI_OFFSET to match what the datasheets say it
should be. However, the bt8x8 datasheets are wrong. The old value of
244 is closer to what is actually observed. The real value appears to
not be constant and is different for different chip revisions.
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Take note of which sysfs files / groups that the pvrusb2 successfully
creates and only delete those specific items when tearing things
down. (Previously we just blindly tore everything down every time.)
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Revert bttv-driver.c from video_device_create_file() to use
class_device_create_file() again. video_device_create_file() is only
available when V4L1 is on.
Proper error checking is added for failure of class_device_create_file().
Will print error message and unroll partially created sysfs entries.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add proper error checking and roll-back for failure of
class_device_create_file() in videodev.c. Print error messages and
unroll partially created sysfs entries.
Also, failure of class_device_register() in video_register_device() is
handled correctly. It was failing to de-allocate the minor number. This
must be done in video_register_device(), since the caller has no way of
knowing if failure occurred before or after the class device was
registered.
Also added an error message if video_register_device() is called with
an unknown type, which should never happen.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A patch from Aug, 17 activated by mistake OVERLAY flag on cx88-video,
together with several cx88-blackbird cleanups. This makes the cx88 driver
to report:
/dev/video0 [v4l2]: ioctl VIDIOC_G_FBUF: Invalid argument
instead of:
/dev/video0 [v4l2]: no overlay support
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removed usage of HAVE_V4L1
Including videodev.h will just include videodev2.h if V4L1 is not supported
V4L1 code at core drivers will honor CONFIG_V4L1_COMPAT stuff
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
video_code size is 24 on i386 and 32 on x86_64, so a proper handling is needed
on compat_ioctl32 to fix it.
This code should be tested, since just *a few* boards use this ioctl.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Check __must_check warnings for class_device_register and class_device_create_file
video_device_create_file was declared as a void, but instead should
return the int value of class_device_create_file.
Move the check from bttv-driver.c into v4l2-dev.h, because all other
callers of video_device_create_file must also be checked.
Replace the call to class_device_create_file in videodev.c with
video_device_create_file, as defined in v4l2-dev.h, so that the
return value of class_device_create_file will be checked.
Check the return value of class_device_register in videodev.c and
pvrusb2-sysfs.c
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
With the LG H06xF tuners, an auxiliary byte must be sent after the
standard four-byte i2c sequence. The code that does this is currently in
the wrong place, causing random bytes to be written to the tuner over
i2c in the set_type function.
This patch moves this code from set_type to default_set_tv_freq.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix keycode calculations (all codes for this remote were wrong due to a
lost + sign)
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Two different exports with the same name are not a good idea:
$ grep -r EXPORT_SYMBOL\(dmasound_init\) *
drivers/media/video/saa7134/saa7134-core.c:EXPORT_SYMBOL(dmasound_init);
sound/oss/dmasound/dmasound_core.c:EXPORT_SYMBOL(dmasound_init);
$
This patch renames the saa7134 dmasound_{init,exit} to
saa7134_dmasound_{init,exit}.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch just sets the option noninterlaced to 1 by default since
it has no known disadvantages. It is still possibe to get the old
behaviour by setting noninterlaced=0.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
To prevent autoloading of the driver, as it then conflicts with every other
saa7146 device in existence.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use release_firmware() to free requested resources.
According to Documentation/firmware_class/README the request_firmware()
call should be followed by a release_firmware(). Some drivers do not
however free the firmware previously allocated with request_firmware().
This patch tries to fix this by making sure that release_firmware() is used
as expected.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following possible cleanups:
- make needlessly global code static
- #if 0 unused global functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for the Geniatech Digistar, aka
Digiwave 103g DVB-S card.
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Saqeb Akhter <johoja@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Previously the pvrusb2 driver was conditionalizing printing of the
device register / unregister messages against a debug mask. This sort
of information should always appear, thus this patch.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The supported standards by the tuner on tveeprom were too restricted.
It were showing just the main format, instead of the format family.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Many tda9887 settings depend on the chosen tuner. Expand the tuner parameters
to include these tda9887 settings.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We should no longer try to load the tda9887 module, because it no longer
exists. The tda9887 driver has been merged into the tuner module.
This patch removes all instances of request_module("tda9887") from
the following video4linux drivers: bttv, cx88, em28xx and saa7134.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch implements the newer v4l2 control features to make the
standard user controls and mpeg encoder controls of cx88-blackbird
video encoder boards available to userspace.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6: (22 commits)
[PATCH] devfs: Remove it from the feature_removal.txt file
[PATCH] devfs: Last little devfs cleanups throughout the kernel tree.
[PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV
[PATCH] devfs: Remove the tty_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the line_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the videodevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed
[PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree
[PATCH] devfs: Remove devfs_remove() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_cdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_symlink() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree
[PATCH] devfs: Remove devfs_*_tape() functions from the kernel tree
[PATCH] devfs: Remove devfs support from the sound subsystem
[PATCH] devfs: Remove devfs support from the ide subsystem.
[PATCH] devfs: Remove devfs support from the serial subsystem
[PATCH] devfs: Remove devfs from the init code
[PATCH] devfs: Remove devfs from the partition code
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
[PATCH] i386: export memory more than 4G through /proc/iomem
[PATCH] 64bit Resource: finally enable 64bit resource sizes
[PATCH] 64bit Resource: convert a few remaining drivers to use resource_size_t where needed
[PATCH] 64bit resource: change pnp core to use resource_size_t
[PATCH] 64bit resource: change pci core and arch code to use resource_size_t
[PATCH] 64bit resource: change resource core to use resource_size_t
[PATCH] 64bit resource: introduce resource_size_t for the start and end of struct resource
[PATCH] 64bit resource: fix up printks for resources in misc drivers
[PATCH] 64bit resource: fix up printks for resources in arch and core code
[PATCH] 64bit resource: fix up printks for resources in pcmcia drivers
[PATCH] 64bit resource: fix up printks for resources in video drivers
[PATCH] 64bit resource: fix up printks for resources in ide drivers
[PATCH] 64bit resource: fix up printks for resources in mtd drivers
[PATCH] 64bit resource: fix up printks for resources in pci core and hotplug drivers
[PATCH] 64bit resource: fix up printks for resources in networks drivers
[PATCH] 64bit resource: fix up printks for resources in sound drivers
[PATCH] 64bit resource: C99 changes for struct resource declarations
Fixed up trivial conflict in drivers/ide/pci/cmd64x.c (the printk that
was changed by the 64-bit resources had been deleted in the meantime ;)
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes two needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A card number is not unique enough. Instead, let the caller specify the
prefix of the status messages.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab