The qual element in ieee80211_rx_status is not used anymore, so we don't need
to set it in the wl1271_rx_status() function. This saves a bit of time in
the RX path.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PA calibration for ar9271 ath9k_hw_9271_pa_cal() can run during
reset or initial calibration, update the PA calibration to account
for that and initialize PA calibration variables for both conditions.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is required for the ar9271 hardware as well.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'XFP' driver is really a driver for the QT2022C2 and QT2025C PHYs,
covering both more and less than XFP. Rename its functions and
constants to reflect reality and to reduce namespace pollution when
sfc is a built-in driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only multi-speed PHY driver using this is 10Xpress, and it does
not support non-autoneg operation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_fc_resolve() is specific to MDIO and is not used by any other
function.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTD partition is named based on the netdev name, which is set to
'eth%d' before registration. Also, the MTD partition will currently
be left registered if netdev registration fails.
Fix both these problems by moving the MTD probe after netdev
registration. Hold the RTNL to serialise this with the netdev
notifier that calls efx_mtd_rename().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These cleanup functions will never be called if the MMIO region could
not be mapped.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC and PHY probing are bound up together, as evidenced by the
initialisation of efx_nic::loopback_modes. Remove the current
arbitrary separation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies the implementation a lot.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes efx_pci_remove_main() more obviously the inverse of
efx_pci_probe_main(), and matches our out-of-tree driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the duplicated logic in efx_enqueue_skb() and
efx_tx_queue_insert() with an inline function, efx_max_tx_len().
Remove the failed attempt at abstracting hardware-specifics and put
all the magic numbers in efx_max_tx_len().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move size and mask definitions into efx.h; calculate page orders in falcon.c.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While we're at it, use type suffixes of 'd', 'q' and 'o', consistent
with register type names.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Siena is still based on the Falcon hardware architecture and will
share many of these definitions, so replace falcon_hwdefs.h with
regs.h.
The new definitions have been generated according to a naming
convention which incorporates the type and revision information.
Update the code accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there are now separate blocks of code to set the thresholds for
each NIC type, it is no longer useful to include them in the NIC type
description.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros are not extensible to more than two NIC types without
repetition of register definitions, and they are only used to deal
with a few fields in RX_CFG_REG and global events which moved between
Falcon rev A1 and B0.
Therefore:
- Move RX_CFG_REG initialisation into its own function which tests the
NIC revision just once
- Explicitly test the NIC revision when checking the RX_RECOVERY flag in
global events
- Merge definitions of RX_XOFF_MAC_EN flag, which did not move
- Remove the macro definitions
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Siena will require entirely different board code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commits 27fbc7d 'mdio: Expose pause frame advertising flags to ethtool'
and c634263 'sfc: 10Xpress: Initialise pause advertising flags'
added to our reported advertising flags.
efx_mdio_set_settings() requires that all advertising flags are
also present in the supported flags, so make sure that is true.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the private functions alloc_can_skb() and
alloc_can_err_skb() of the at91_can driver public and adapts all
drivers to use these. While making the patch I realized, that
the skb's are *not* setup consistently. It's now done as shown
below:
skb->protocol = htons(ETH_P_CAN);
skb->pkt_type = PACKET_BROADCAST;
skb->ip_summed = CHECKSUM_UNNECESSARY;
*cf = (struct can_frame *)skb_put(skb, sizeof(struct can_frame));
memset(*cf, 0, sizeof(struct can_frame));
The frame is zeroed out to avoid uninitialized data to be passed to
user space. Some drivers or library code did not set "pkt_type" or
"ip_summed". Also, "__constant_htons()" should not be used for
runtime invocations, as pointed out by David Miller.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i2400m-sdio requires iwmc3200top for its operation
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iwmc3200wifi requires iwmc3200top for its operation
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds Intel Wireless MultiCom 3200 top driver.
IWMC3200 is 4Wireless Com CHIP (GPS/BT/WiFi/WiMAX).
Top driver is responsible for device initialization and firmware download.
Firmware handled by top is responsible for top itself and
as well as bluetooth and GPS coms. (Wifi and WiMax provide their own firmware)
In addition top driver is used to retrieve firmware logs
and supports other debugging features
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change RX large buffer size based on MTU. If pages are larger
than the MTU the page is divided up into multiple chunks and passed to
the hardware. When pages are smaller than MTU each RX buffer can
contain be comprised of up to 2 pages.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to have better cache layouts of struct sock (separate zones
for rx/tx paths), we need this preliminary patch.
Goal is to transfert fields used at lookup time in the first
read-mostly cache line (inside struct sock_common) and move sk_refcnt
to a separate cache line (only written by rx path)
This patch adds inet_ prefix to daddr, rcv_saddr, dport, num, saddr,
sport and id fields. This allows a future patch to define these
fields as macros, like sk_refcnt, without name clashes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xmit handler doesn't need to wake the queue after stopping
it temporarily (some other drivers are doing the same).
Patch on net-next-2.6, multiple netperf sessions tested.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Group device now cleanly reacts to failures during channel start and
implements a clean rollback.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The creation of a new lcs device requires a call to the function
ccw_device_set_online() for the read and the write channel. Failure
of either call should terminate the lcs device creation immediately
with return code -ENODEV.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Timer_list structure in lcs_send_lancmd() is allocated on stack.
Initialization with init_timer() leads to above ODEBUG message.
Instead use init_timer_on_stack() which prevents above msg.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware hang detection and recovery (reset) need to
be disabled for diagnostic tools, which can run
some disruptive tests.
This adds a driver level control to turn off this
feature by diag tools.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use -EIO or -EINVAL as error codes, these can get passed up
to applications (tools).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for different windowing scheme for on chip
memory in future chip revisions. This is required by
diagnostic tools.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Future revisions need different chip reset sequence
and firmware initialization.
Also clean up some never used debug code.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Future revisions of the chip have 128 bit memory
transactions. Require drivers to implement rmw
in case of sub-128 bit accesses by driver. This
is mostly used by diagnostic tools.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new PCI ids to support next generation of BladeEngine device.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device is limited to the maximal BW allocation, so it should be displayed as
the link speed to notify the user.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is really no need to clear the MAC or the FW filtering rules - it was
added for completion, but caused race conditions with load/unload. Removing this
redundant code
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DCC commands are not protected with the RTNL lock, so a mutex should be added
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When working with DCC, a function can be disabled or enabled (virtual link down
or up). Using the function state introduced some race conditions with the
load/unload flow.
Using a separate flag to indicate that the function is disabled.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Value of zero was used to disable the fairness mechanism. Though the code
(driver and FW) allowed changing the value at run time, it did not allow to do
that if the mechanism was disabled to begin with.
Fixed the FW to allow turning on and off the mechanism at run time. Fixed the
code to read the value from the chip at the right sequence.
Without this fix, if the initial value was set to zero, traffic could not run on
the interface.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lock_kernel/unlock_kernel() in cycle_kernel_lock() which is called
in tun_chr_open() is not serializing against anything and safe to
remove.
tun_chr_fasync() is serialized by get/put_tun() and fasync_helper()
has no dependency on BKL. The modification of tun->flags is racy with
and without the BKL so removing it does not make it worse.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mechanism to clear the statistics register is dependent
on the status of GMIIEN bit in MAC control register. If the
GMIIEN bit is set, the stats registers are write to decrement.
If the GMIIEN bit is cleared, the stats registers are plain
read/write registers. The stats register clearing operation
must take into account the current state of GMIIEN as it
can be cleared when the interface is brought down.
With existing implementation logic, querying for interface stats
when the interface is down, can corrupt the statistics counters.
This patch examines the GMIIEN bit status in MAC_CONTROL
register before choosing an appropriate mask for clearing stats
registers.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Acked-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extracted from Realtek's 8.012.00 r8168 driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Simon Farnsworth <simon.farnsworth@onelan.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the driver to accept a MAC address specified in platform_data.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5675f221 overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 337e067d overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 23d26497 overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit fd8235bb overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 59aa3cc4 overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sysfs entries to enable register and memory access
for diagnostic tools.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since register and onboard memory access has separate
window registers, they need not be kept under same lock.
Also, memory is always accessed from process context
(mostly for firmware init and diagnostic tools).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use common variables crb_win, ocm_win for all revisions of chip.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add access to on chip memory, this is used by
debug and diagnostic tools only.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sub 64-bit / unaligned access to oncard memory was only used
by old diagnostic tools, causes some intermittent issues when
memory controller agent is used. The new access method was
added by commit ea6828b8aa
("netxen: improve pci memory access"). Firmware init anyway
uses 8-byte strides.
This also fixes address/offset calculation for NX2031 context
memory (SIU). For NX3031, SIU uses same register offsets
as packet memory (MIU).
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bit V_MAC_RX_PL_THRSH(4) was already set a few lines higher.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The negation makes it a bool before the comparison and hence it
will never evaluate to true.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added support of private MAC address per port and provisioning
packet handler for iSCSI traffic only.
The above changes are isolated to the cxgb3 driver, independent of any scsi or iscsi driver changes.
Acked-by: Karen Xie <kxie@chelsio.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Rakesh Ranjan <rakesh@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Runtime PM support to the sh_eth driver.
The clock to the ethernet hardware block will be
enabled as long as the network device is up.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the sh_eth driver to allow passing the mac address
using the platform data structure. This to simplify board
setup code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the CAN controller driver to define the number of echo
skb's used for the local loopback (echo), as suggested by Kurt Van
Dijck, with the function:
struct net_device *alloc_candev(int sizeof_priv,
unsigned int echo_skb_max);
The CAN drivers have been adapted accordingly. For the ems_usb driver,
as suggested by Sebastian Haas, the number of echo skb's has been
increased to 10, which improves the transmission performance a lot.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cisco HDLC uses keepalive packets and sequence numbers to determine link
state. In rare cases both ends could transmit keepalive packets at the same
time, causing the received sequence numbers to be treated as incorrect.
Now we accept our current sequence number as well as the previous one.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function bond_create_proc_entry is currently of type int.
Two versions of this function exist:
The one in the ifdef CONFIG_PROC_FS branch always return 0.
The one in the else branch (which is empty) return nothing.
When CONFIG_PROC_FS is undef, this cause the following warning:
drivers/net/bonding/bond_main.c: In function `bond_create_proc_entry':
drivers/net/bonding/bond_main.c:3393: warning: control reaches end of
non-void function
No caller of this function use the returned value.
So change the returned type from int to void and remove the
useless return 0; .
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Reported-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
3c574_cs:
spin_lock the set_multicast_list function.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Belkin F8T012xx1 bluetooth adaptor has the same vendor and product
IDs as the Belkin F5D5050, so we need to teach the pegasus driver to
ignore adaptors belonging to the "Wireless" class 0xE0. For this one
case anyway, seeing as pegasus is a driver for "Wired" adaptors.
Signed-off-by: Chris Rankin <rankincj@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resource_size_t for PCI resource remapping instead
of unsigned long. Physical addresses can exceed range of
long data type (e.g with PAE).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethoc.c: In function ‘ethoc_open’:
drivers/net/ethoc.c:667: warning: comparison of distinct pointer types
lacks a cast
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/wireless/libertas/cmdresp.c: In function ‘lbs_process_event’:
drivers/net/wireless/libertas/cmdresp.c:519: error: ‘TASK_INTERRUPTIBLE’
undeclared (first use in this function)
drivers/net/wireless/libertas/cmdresp.c:519: error: (Each undeclared
identifier is reported only once
drivers/net/wireless/libertas/cmdresp.c:519: error: for each function it
appears in.)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet NIC driver for VMware's vmxnet3
From: Shreyas Bhatewara <sbhatewara@vmware.com>
This patch adds driver support for VMware's virtual Ethernet NIC: vmxnet3
Guests running on VMware hypervisors supporting vmxnet3 device will thus have
access to improved network functionalities and performance.
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Ronghua Zhang <ronghua@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IXP 2000 network driver was failing to build as it has its own
statistics gathering which was not compatible with the recent network
device operations changes. This patch fixes the driver in the obvious
way and has been compile tested. I have been unable to get the ixp2000
maintainer to comment or test this fix.
Signed-off-by: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio module now handles reconfiguration of pause advertising
through ethtool, but not initialisation. Add the necessary
initialisation to tenxpress_phy_init().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mdio45_ethtool_gset_npage() and mdio45_ethtool_gset(), check MDIO
pause frame advertising flags and set the corresponding ethtool flags.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if pause autoneg is off we do not set either pause
advertising flag. If autonegotiation of speed and duplex settings is
enabled, there is no way for the link partner to distinguish this from
our refusing to use pause frames.
We should instead set the advertising flags according to the forced
mode so that the link partner can follow our lead. This is consistent
with the behaviour of other drivers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to various cleanups and refactorings this is now straightforward:
convert the gianfar driver to dev_pm_ops, plus add ->restore() callback
that will fully reinitialize MAC internal registers and BDs.
Note that I kept legacy suspend/resume callbacks so that this patch
doesn't depend on PowerPC changes (i.e. dev_pm_ops support for OF
platform drivers).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After hibernation we want to just reinitialize BDs, no need to allocate
anything. So, factor out BDs initialization code from
gfar_alloc_skb_resourses().
Also, teach gfar_init_bds() to reuse already allocated RX SKBs, i.e.
just call gfar_init_rxbdp() if a SKB was already allocated and mapped.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to just reinitialize RX BDs after hibernation, no need to
map the skb->data again. So let's factor gfar_init_rxbdp() out of
gfar_new_rxbdp().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For hibernation we want to call gfar_init_mac() without need to
free/allocate_skb_resources sequence, so save the DMA address into a
private struct, and move tbase/rbase initialization to gfar_init_mac().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two new functions implemented: gfar_alloc_skb_resources() and
gfar_init_mac(). We'll use gfar_init_mac() for restoring after
hibernation.
The patch just moves the code around, there should be no functional
changes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
startup_gfar() sets the wrap bit for the last rxbd just after
gfar_new_rxbdp() call, which is issued for all rxbds. And
gfar_new_rxbdp() has the following check already:
if (bdp == priv->rx_bd_base + priv->rx_ring_size - 1)
lstatus |= BD_LFLAG(RXBD_WRAP);
So we don't need to set the bit again.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove dma_free_coherent() from stop_gfar() and gfar_start() calls,
place it into free_skb_resources(). That makes SKB resources management
more understandable, plus free_skb_resources() will be used as a cleanup
routine for gfar_alloc_skb_resources() that will be implemented soon.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're going to split the startup_gfar() into 3 separate functions,
so let's cleanup the code a little bit so that cosmetic changes
won't distract attention from logical ones.
- Remove needless casts (e.g. (struct sk_buff **)kmalloc());
- Turn 'unsigned long vaddr;' into 'void *vaddr', to avoid casting;
- Add new 'struct device *dev' variable as a shorthand for
'&priv->ofdev->dev' that is used all over the place, also rename
'struct net_device *dev' to 'struct net_device *ndev';
- Turn printk(KERN_ERR ...) to pr_err(...), which is shorter;
- Don't return bogus -1 (i.e. -EPERM) when request_irq() fails;
- Turn '&priv->regs->' to just '®s->'.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/cnic.c: In function 'cnic_init_storm_conn_bufs':
drivers/net/cnic.c:1757: error: implicit declaration of function 'csum_ipv6_magic'
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool set settings to pasemi_mac_ethtool.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/wireless/libertas/cmdresp.c: In function ‘lbs_process_event’:
drivers/net/wireless/libertas/cmdresp.c:519: error: ‘TASK_INTERRUPTIBLE’
undeclared (first use in this function)
drivers/net/wireless/libertas/cmdresp.c:519: error: (Each undeclared
identifier is reported only once
drivers/net/wireless/libertas/cmdresp.c:519: error: for each function it
appears in.)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to the way it interacts with the networking
stack and other parts of mac80211, ieee80211_rx()
must be called with disabled softirqs.
[1] http://thread.gmane.org/gmane.linux.kernel.wireless.general/39440/focus=40266
Reported-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Need to free the dynamic allocated memory before ieee80211_free_hw();
once call ieee80211_free_hw(), should not reference to "priv" data
structure.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If ace_load_firmware() fails, ace_init() cleans up but still returns
0, leading to an oops as seen in <http://bugs.debian.org/521383>.
It should pass the error code up.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add iSCSI support for bnx2x devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Shmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hardware and software structures for bnx2x devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor ring init. code for subsequent 10G patches. Also add rtnl_lock()
in cnic_uio_open() to prevent race condition with netdev events.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the main CNIC registration, callback, MAC addr. setup functions.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Shmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to initialize hardware blocks used for iSCSI.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Shmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For iSCSI MAC address setup in later patches.
Signed-off-by: Shmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the SPQ (slow-path queue) operations will be used
by the cnic code in later patches.
Signed-off-by: Shmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_ring->sbq_buf_len now holds the length of the mapped portion of the
buffer rather than the overall length.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver has nothing to do, but this marker prevents the event from
showing up 'not handled'.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove explicit setting of error reporting bits.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need PHY drivers to initialize in a static kernel before
the MAC drivers that use them. So link them in first.
Based upon a report by Felix Radensky.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is somewhat non-sensical to allow selecting wireless
drivers without showing wireless core code options, and
since the wext refactoring this has made it possible to
generate configurations that will not build. Avoid this
and make wireless drivers select the wireless options.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This came in through the patch titled:
libertas: first stab at cfg80211 support
I only noticed it because it breaks compat-wireless :)
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: sujith.manoharan@atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows the recently added backplane device IDs that support KR
to fail over to KX during link setup. This is accomplished by the new MAC
link setup function ixgbe_setup_mac_link_smartspeed(). Comments were also
updated to better document the reason for the delays chosen for KX, KX4, BX,
BX4 and KR connections.
Signed-off-by: Don Skidmore <don.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will add the device ID for the 82599-based Ethernet
Express Module X520-P2 SFI card.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the EMAC V4 implementations support 16K Tx FIFOs. This
patch adds support for this functionality and fixes typos in the
Tx FIFO size error messages.
Signed-off-by: Dave Mitchell <dmitchell@appliedmicro.com>
Acked-by: Prodyut Hazarika <phazarika@appliedmicro.com>
Acked-by: Victor Gallardo <vgallardo@appliedmicro.com>
Acked-by: Loc Ho <lho@appliedmicro.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was accidentally omitted from one of the previous patches for firmware event
handling. The handler needs to the enable firmware irq mask when it's done
processing or it may not get any more events interrupts.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call set_multi API after reset recovery. This was exposed by tripping
tx_timeout.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wait for NIC fifo and MGMNT fifo to empty before applying reset.
Otherwise broken frames can be processed by management processor and
cause it to hang.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The addresses were being added to the filter properly, but were not
being enabled. This adds enable bit to filter write.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcast/multicast should always be routed to the default (zeroeth) rx
ring. Broadcast frames are already routed correctly. This fixes
routing for multicast frames.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently frames are routed based on their type and MAC address. This
patch adds the port number on which the frame arrived to the routing.
This prevents problems in the case where both interfaces have the same MAC address in
a routing configuration.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix RX queue table size and change from random to default hash values.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI HECC (High End CAN Controller) module is found on many TI devices. It
has 32 hardware mailboxes with full implementation of CAN protocol 2.0B
with bus speeds up to 1Mbps. Specifications of the module are available
on TI web <http://www.ti.com>
Signed-off-by: Anant Gole <anantgole@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private myri10ge_priv structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable old_active is first set to bond->curr_active_slave.
Then, it is unconditionally set to new_active, without being used in between.
The first assignment, having no side effect, is useless.
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When parsing module parameters, bond_check_params() erroneously use
'xor_mode' as the name of a module parameter in an error message.
The right name for this parameter is 'xmit_hash_policy'.
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
As kindly pointed out by Andrey Yurovsky, CONFIG_LIBERTAS already
selects FW_LOADER.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
lbs_is_cmd_allowed() check is added in __lbs_cmd_async() and
lbs_prepare_and_send_command(). The check is removed from other places.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And move it to hw code on mac.c where it belongs.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The core driver needs to be stopped and then as a last step the
hardware needs to be stopped and its structure free'd. We do this
by moving the core driver cleanup to a new helper ath_clean_core()
and have ath_cleanup() call it. Only as a last step does
ath_cleanup() now free the hw.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is used in several places, ensure we do it right in all
callers by using a helper.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
debugfs uses the hardware for several debugfs files as such the
hardware must be initialized and available prior to its usage. The
same applies to when we free the hw structs -- free debufs file
entries prior to free'ing the hardware.
Reported-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
What this means is we can enable now debug prints without
requiring CONFIG_ATH9K_DEBUG.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 has long provided us the association ID. This isn't useful except
for Power-Save polling which now gets enabled. We can now poll for our
pending frames on the AP during power save.
You can review the details of Power-Save on the wireless wiki:
http://wireless.kernel.org/en/developers/Documentation/ieee80211/power-savings
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a regression introduced by patch titled:
"atheros: define shared bssidmask setting"
The register for the BSSID was exchanged for the bssid mask register.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have access to common->curbssid and common->curaid so just
use those. Note that common->curaid is always 0 so this keeps
our current behaviour of always using 0 for now. Once we fix
storing the association ID passed by mac80211 this will
require no changes here.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The trick was to add four bytes whenever this was used. There
are two places where this was missed.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a typo on the second bssid mask register.
This was caused by the patch titled:
"ath5k: use common curbssid, bssidmask and macaddr"
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also sorts all "source" lines in the wireless/Kconfig.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify the suspend and resume callbacks of ath5k by converting the
driver to struct dev_pm_ops and allowing the PCI PM core to do the
PCI-specific suspend/resume handling.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set firmware and hardware version in wiphy so that user space can access
it.
(Modification from original in favor of cfg80211 ethtool support. -- JWL)
Cc: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both 1000 & 6000 series NICs contain on-chip OTP memory that
replaces the off-chip EEPROM memory. The nature of OTP means
there is a limited number of times a particular board can go through the
factory flow and be (re)calibrated. As a consequence there will be some boards
that contain EEPROM memory because OTP blocks were full.
In the signature validation routine, iwlwifi needs to make sure
"select bit" and "EEPROM/OTP signature" agree on the type of
NVM to be used to configure the system.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace iwl_poll_direct_bit with iwl_poll_bit when accessing CSR registers.
There is no need to power up the mac to access CSR registers.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Ben M Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unify the usage of apm_stop_master and apm_stop
across all hardwares.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The iwlwifi drivers have LED blinking requirements that
mac80211 cannot fulfill due to the use of just a single
LED instead of different ones for TX, RX, radio etc.
Instead, the single LED blinks according to transfers
and is solid on the rest of the time. As such, having
LED class devices registered that mac80211 triggers are
connected to is pointless as we don't use the triggers
anyway.
Remove all the useless code and add hooks into the
driver itself. At the same time, make the LED code
abstracted so the core code that determines blink rate
etc. can be shared between 3945 and agn in iwlcore.
At the same time, the fact that we removed the use of
the mac80211 LED triggers means we can also remove the
IWLWIFI_LEDS Kconfig symbol since the LED support is
now self-contained.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to have an easier way to debug issues, create
trace events (using the ftrace framework) that will
allow us to follow exactly what the driver is doing
with the device.
The text format isn't all that useful, but the binary
format can also be obtained easily via debugfs and
then analysed on the fly or offline with debugging
tools.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Multiple MPDUs can be aggregated, transmitted, and finally acknowledged
together using a single BA frame. Block ACK (BA) contains
bitmap size of 64*16 bits so the maximum frame count is 64.
The default value of aggregation frame count suggested by uCode is 31 to
achieve best performance.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver should clear the translate table area after receiving "Alive"
response from uCode. This patch corrects a mistake when doing this.
Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Guo Chaohong <chaohong.guo@linux.intel.com>
Acked-by: Ben M Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to support different type of 1000 series NICs we release to
customers before the production release, iwlwifi driver need to support
all the NICs has EEPROM version greater than 0x15c.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When uCode detects critical temperature it should send "card state
notification" interrupt to driver and then shut itself down to prevent
overheating. There is a race condition where uCode shuts down before it
can deliver the interrupt to driver.
Additional method provided here for driver to enter CT_KILL state based
on temperature reading.
How it works:
Method 1:
If driver receive "card state notification" interrupt from uCode; it
enters "CT_KILL" state immediately
Method 2:
If the last temperature report by Card reach Critical temperature,
driver will send "statistic notification" request to uCode to verify the
temperature reading, if driver can not get reply from uCode within
300ms, driver will enter CT_KILL state automatically.
Method 3:
If the last temperature report by Card did not reach Critical
temperature, but uCode already shut down due to critical temperature.
All the host commands send to uCode will not get process by uCode;
when command queue reach the limit, driver will check the last reported
temperature reading, if it is within pre-defined margin, enter "CT_KILL"
state immediately. In this case, when uCode ready to exit from "CT_KILL" state,
driver need to restart the adapter in order to reset all the queues and
resume normal operation.
One additional issue being address here, when system is in CT_KILL
state, both tx and rx already stopped, but driver still can send host
command to uCode, it will flood the command queue since card was not
responding; adding STATUS_CT_KILL flag to reject enqueue host commands
to uCode if it is in CT_KILL state, when uCode is ready to come out of
CT_KILL, driver will clear the STATUS_CT_KILL bit and allow enqueue the host
commands to uCode to recover from CT_KILL state.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The file was accidentally added in commit ef2f8d4577 ("wl1251: add
wl1251 prefix to all 1251 files"). This happened when I rebased the
patches from a private tree.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add timer based auto deep sleep feature in libertas driver which can be
configured using iwconfig command. This is tested on SD8688, SD8686 cards
with firmware versions 10.38.1.p25, 9.70.4.p0 respectively on 32-bit and 64-bit
platforms. Tests have been done for USB/CS cards to make sure that the patch
won't break USB/CS code. We didn't test the if_spi driver.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the incorporation of the patch entitled "wext: refactor", some
of the wireless drivers in drivers/staging fail to build because they
need to have CONFIG_WIRELESS_EXT and CONFIG_WEXT_PRIV defined.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Refactor wext to
* split out iwpriv handling
* split out iwspy handling
* split out procfs support
* allow cfg80211 to have wireless extensions compat code
w/o CONFIG_WIRELESS_EXT
After this, drivers need to
- select WIRELESS_EXT - for wext support
- select WEXT_PRIV - for iwpriv support
- select WEXT_SPY - for iwspy support
except cfg80211 -- which gets new hooks in wext-core.c
and can then get wext handlers without CONFIG_WIRELESS_EXT.
Wireless extensions procfs support is auto-selected
based on PROC_FS and anything that requires the wext core
(i.e. WIRELESS_EXT or CFG80211_WEXT).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hw code should never use private driver data, but
sometimes we need a backpointer so just stuff it on
the common ath struct.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows for hw support to be enabled for ar9271.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hw code for Atheros 802.11n hardware is commmon between
different chipsets. This moves this code into a separate
module, the next expected user of this code will be
the ath9k_htc module.
The ath9k/ dir is now selected by ATH9K_HW, an option which
gets selected by either ath9k or ath9k_htc, but remains
invisible for user menuconfig configuration. If either
ath9k or ath9k_htc will be compiled into the kernel
ath9k_hw will also be compiled in.
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PCI and debug code will not be shared between ath9k and
ath9k_htc, so make that code use the common read/write ops.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho