The error codes were not set on some of these error paths.
Also the error handling was more confusing than it needed to be so I
cleaned it up and shuffled it around a bit.
Fixes: d2fb0a0438 ("dmaengine: break out channel registration")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201113101631.GE168908@mwanda
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Split IS_ERR_OR_NULL() check followed by additional conditional
to two simple conditionals. This increases readability and saves memory:
Function old new delta
dma_request_chan 700 697 -3
Total: Before=10224, After=10221, chg -0.03%
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200828144519.14483-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
New drivers should use dma_request_chan() instead
dma_request_slave_channel()
dma_request_slave_channel() is a simple wrapper for dma_request_chan()
eating up the error code for channel request failure and makes deferred
probing impossible.
Move the dma_request_slave_channel() into the header as inline function,
mark it as deprecated.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200828110507.22407-1-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are DMA devices (like ours version of Synopsys DW DMAC) which have
DMA capabilities non-uniformly redistributed between the device channels.
In order to provide a way of exposing the channel-specific parameters to
the DMA engine consumers, we introduce a new DMA-device callback. In case
if provided it gets called from the dma_get_slave_caps() method and is
able to override the generic DMA-device capabilities.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200723005848.31907-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some devices may lack the support of the hardware accelerated SG list
entries automatic walking through and execution. In this case a burden of
the SG list traversal and DMA engine re-initialization lies on the
DMA engine driver (normally implemented by using a DMA transfer completion
IRQ to recharge the DMA device with a next SG list entry). But such
solution may not be suitable for some DMA consumers. In particular SPI
devices need both Tx and Rx DMA channels work synchronously in order
to avoid the Rx FIFO overflow. In case if Rx DMA channel is paused for
some time while the Tx DMA channel works implicitly pulling data into the
Rx FIFO, the later will be eventually overflown, which will cause the data
loss. So if SG list entries aren't automatically fetched by the DMA
engine, but are one-by-one manually selected for execution in the
ISRs/deferred work/etc., such problem will eventually happen due to the
non-deterministic latencies of the service execution.
In order to let the DMA consumer know about the DMA device capabilities
regarding the hardware accelerated SG list traversal we introduce the
max_sg_burst capability. It is supposed to be initialized by the DMA engine
driver with 0 if there is no limitation of the number of SG entries
atomically executed and with non-zero value if there is such constraints,
so the upper limit is determined by the number set to the property.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200723005848.31907-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some hardware aside from default 0/1 may have greater minimum burst
transactions length constraints. Here we introduce the DMA device
and slave capability, which if required can be initialized by the DMA
engine driver with the device-specific value.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200723005848.31907-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Bunch of updates to drivers like dmatest, dw-edma, ioat,
mmp-tdma and k3-udma along with Renesas binding update to json-schema
-----BEGIN PGP SIGNATURE-----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=Jun4
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.8-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"A fairly small dmaengine update which includes mostly driver updates
(dmatest, dw-edma, ioat, mmp-tdma and k3-udma) along with Renesas
binding update to json-schema"
* tag 'dmaengine-5.8-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (39 commits)
dmaengine: imx-sdma: initialize all script addresses
dmaengine: ti: k3-udma: Use proper return code in alloc_chan_resources
dmaengine: ti: k3-udma: Remove udma_chan.in_ring_cnt
dmaengine: ti: k3-udma: Add missing dma_sync call for rx flush descriptor
dmaengine: at_xdmac: Replace zero-length array with flexible-array
dmaengine: at_hdmac: Replace zero-length array with flexible-array
dmaengine: qcom: bam_dma: Replace zero-length array with flexible-array
dmaengine: ti: k3-udma: Use PTR_ERR_OR_ZERO() to simplify code
dmaengine: moxart-dma: Drop pointless static qualifier in moxart_probe()
dmaengine: sf-pdma: Simplify the error handling path in 'sf_pdma_probe()'
dmaengine: qcom_hidma: use true,false for bool variable
dmaengine: dw-edma: support local dma device transfer semantics
dmaengine: Fix doc strings to satisfy validation script
dmaengine: Include dmaengine.h into dmaengine.c
dmaengine: dmatest: Describe members of struct dmatest_info
dmaengine: dmatest: Describe members of struct dmatest_params
dmaengine: dmatest: Allow negative timeout value to specify infinite wait
Revert "dmaengine: dmatest: timeout value of -1 should specify infinite wait"
dmaengine: stm32-dma: direct mode support through device tree
dt-bindings: dma: add direct mode support through device tree in stm32-dma
...
The validation kernel doc script complains about undescribed
function parameters
.../dmaengine.c:155: warning: Function parameter or member 'dev' not descr ibed in 'dev_to_dma_chan'
.../dmaengine.c:251: warning: cannot understand function prototype: 'dma_cap_mask_t dma_cap_mask_all; '
.../dmaengine.c:257: warning: cannot understand function prototype: 'struct dma_chan_tbl_ent '
.../dmaengine.c:264: warning: cannot understand function prototype: 'struct dma_chan_tbl_ent __percpu *channel_table[DMA_TX_TYPE_END]; '
.../dmaengine.c:304: warning: Function parameter or member 'chan' not described in 'dma_chan_is_local'
.../dmaengine.c:304: warning: Function parameter or member 'cpu' not described in 'dma_chan_is_local'
.../dmaengine.c:414: warning: Function parameter or member 'chan' not described in 'balance_ref_count'
.../dmaengine.c:447: warning: Function parameter or member 'chan' not described in 'dma_chan_get'
.../dmaengine.c:494: warning: Function parameter or member 'chan' not described in 'dma_chan_put'
Add descriptions to the function parameters and in some cases update
existing text as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200429122151.50989-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When the channel register code was changed to allow hotplug operations,
dynamic indexing wasn't taken into account. When channels are randomly
plugged and unplugged out of order, the serial indexing breaks. Convert
channel indexing to using IDA tracking in order to allow dynamic
assignment. The previous code does not cause any regression bug for
existing channel allocation besides idxd driver since the hotplug usage
case is only used by idxd at this point.
With this change, the chan->idr_ref is also not needed any longer. We can
have a device with no channels registered due to hot plug. The channel
device release code no longer should attempt to free the dma device id on
the last channel release.
Fixes: e81274cd6b ("dmaengine: add support to dynamic register/unregister of channels")
Reported-by: Yixin Zhang <yixin.zhang@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Yixin Zhang <yixin.zhang@intel.com>
Link: https://lore.kernel.org/r/158679961260.7674.8485924270472851852.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- Core:
- Some code cleanup and optimization in core by Andy
- Debugfs support for displaying dmaengine channels by Peter
- Drivers:
- New driver for uniphier-xdmac controller
- Updates to stm32 dma, mdma and dmamux drivers and PM support
- More updates to idxd drivers
- Bunch of changes in tegra-apb driver and cleaning up of pm functions
- Bunch of spelling fixes and Replace zero-length array patches
- Shutdown hook for fsl-dpaa2-qdma driver
- Support for interleaved transfers for ti-edma and virtualization
support for k3-dma driver
- Support for reset and updates in xilinx_dma driver
- Improvements and locking updates in at_hdma driver
-----BEGIN PGP SIGNATURE-----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=+UJ7
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"Core:
- Some code cleanup and optimization in core by Andy
- Debugfs support for displaying dmaengine channels by Peter
Drivers:
- New driver for uniphier-xdmac controller
- Updates to stm32 dma, mdma and dmamux drivers and PM support
- More updates to idxd drivers
- Bunch of changes in tegra-apb driver and cleaning up of pm
functions
- Bunch of spelling fixes and Replace zero-length array patches
- Shutdown hook for fsl-dpaa2-qdma driver
- Support for interleaved transfers for ti-edma and virtualization
support for k3-dma driver
- Support for reset and updates in xilinx_dma driver
- Improvements and locking updates in at_hdma driver"
* tag 'dmaengine-5.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (89 commits)
dt-bindings: dma: renesas,usb-dmac: add r8a77961 support
dmaengine: uniphier-xdmac: Remove redandant error log for platform_get_irq
dmaengine: tegra-apb: Improve DMA synchronization
dmaengine: tegra-apb: Don't save/restore IRQ flags in interrupt handler
dmaengine: tegra-apb: mark PM functions as __maybe_unused
dmaengine: fix spelling mistake "exceds" -> "exceeds"
dmaengine: sprd: Set request pending flag when DMA controller is active
dmaengine: ppc4xx: Use scnprintf() for avoiding potential buffer overflow
dmaengine: idxd: remove global token limit check
dmaengine: idxd: reflect shadow copy of traffic class programming
dmaengine: idxd: Merge definition of dsa_batch_desc into dsa_hw_desc
dmaengine: Create debug directories for DMA devices
dmaengine: ti: k3-udma: Implement custom dbg_summary_show for debugfs
dmaengine: Add basic debugfs support
dmaengine: fsl-dpaa2-qdma: remove set but not used variable 'dpaa2_qdma'
dmaengine: ti: edma: fix null dereference because of a typo in pointer name
dmaengine: fsl-dpaa2-qdma: Adding shutdown hook
dmaengine: uniphier-xdmac: Add UniPhier external DMA controller driver
dt-bindings: dmaengine: Add UniPhier external DMA controller bindings
dmaengine: ti: k3-udma: Implement support for atype (for virtualization)
...
Create a placeholder directory for each registered DMA device.
DMA drivers can use the dmaengine_get_debugfs_root() call to get their
debugfs root and can populate with custom files to aim debugging.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200306142839.17910-4-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Via the /sys/kernel/debug/dmaengine/summary users can get information
about the DMA devices and the used channels.
Example output on am654-evm with audio using two channels and after running
dmatest on 4 channels:
dma0 (285c0000.dma-controller): number of channels: 96
dma1 (31150000.dma-controller): number of channels: 267
dma1chan0 | 2b00000.mcasp:tx
dma1chan1 | 2b00000.mcasp:rx
dma1chan2 | in-use
dma1chan3 | in-use
dma1chan4 | in-use
dma1chan5 | in-use
For slave channels we can show the device and the channel name a given
channel is requested.
For non slave devices the only information we know is that the channel is
in use.
DMA drivers can implement the optional dbg_summary_show callback to
provide controller specific information instead of the generic one.
It is easy to extend the generic dmaengine_summary_show() to print
additional information about the used channels.
I have taken the idea from gpiolib and clk subsystems.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200306142839.17910-2-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Dmaengine core warns the drivers registering for missing .device_release
implementation. The warning is accurate for dmaengine controllers which
hotplug but not for rest.
So reduce this to a debug log.
Link: https://lore.kernel.org/r/20200306135018.2286959-1-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
No need to use goto to jump over the
return chan ? chan : ERR_PTR(-EPROBE_DEFER);
We can just revert the check and return right there.
Do not fail the channel request if the chan->name allocation fails, but
print a warning about it.
Change the dev_err to dev_warn if sysfs_create_link() fails as it is not
fatal.
Only attempt to remove the DMA_SLAVE_NAME symlink if it is created - or it
was attempted to be created.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200131093859.3311-2-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 71723a96b8 ("dmaengine: Create symlinks between DMA channels and
slaves") changed the dma_request_chan() function flow in such a way that
it always returns EPROBE_DEFER in case of channels that cannot be found.
This break the operation of the devices which have optional DMA channels
as it puts their drivers in endless deferred probe loop. Fix this by
propagating the proper error value.
Fixes: 71723a96b8 ("dmaengine: Create symlinks between DMA channels and slaves")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200130070834.17537-1-m.szyprowski@samsung.com
[vkoul: fix typo in patch title]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently it is not easy to find out which DMA channels are in use, and
which slave devices are using which channels.
Fix this by creating two symlinks between the DMA channel and the actual
slave device when a channel is requested:
1. A "slave" symlink from DMA channel to slave device,
2. A "dma:<name>" symlink slave device to DMA channel.
When the channel is released, the symlinks are removed again.
The latter requires keeping track of the slave device and the channel
name in the dma_chan structure.
Note that this is limited to channel request functions for requesting an
exclusive slave channel that take a device pointer (dma_request_chan()
and dma_request_slave_channel*()).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Link: https://lore.kernel.org/r/20200117153056.31363-1-geert+renesas@glider.be
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit aa1e6f1a38 ("dmaengine: kill struct dma_client and
supporting infrastructure") removed the last user of the
dma_device_satisfies_mask() wrapper.
Remove the wrapper, and rename __dma_device_satisfies_mask() to
dma_device_satisfies_mask(), to get rid of one more function starting
with a double underscore.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200121093311.28639-2-geert+renesas@glider.be
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The metadata is best described as side band data or parameters traveling
alongside the data DMAd by the DMA engine. It is data
which is understood by the peripheral and the peripheral driver only, the
DMA engine see it only as data block and it is not interpreting it in any
way.
The metadata can be different per descriptor as it is a parameter for the
data being transferred.
If the DMA supports per descriptor metadata it can implement the attach,
get_ptr/set_len callbacks.
Client drivers must only use either attach or get_ptr/set_len to avoid
misconfiguration.
Client driver can check if a given metadata mode is supported by the
channel during probe time with
dmaengine_is_metadata_mode_supported(chan, DESC_METADATA_CLIENT);
dmaengine_is_metadata_mode_supported(chan, DESC_METADATA_ENGINE);
and based on this information can use either mode.
Wrappers are also added for the metadata_ops.
To be used in DESC_METADATA_CLIENT mode:
dmaengine_desc_attach_metadata()
To be used in DESC_METADATA_ENGINE mode:
dmaengine_desc_get_metadata_ptr()
dmaengine_desc_set_metadata_len()
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20191223110458.30766-5-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
error log for dma_channel_table_init() failure pointed a mere
"initialization failure", which is not very helpful message, so print
additional details like function name and error code.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We call dma_device_put() and module_put() after invoking
.device_free_chan_resources callback, but we should also take care of
router devices and invoke this after .route_free callback. So move it
after .route_free
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Adding a reference count helps drivers to properly implement the unbind
while in use case.
References are taken and put every time a channel is allocated or freed.
Once the final reference is put, the device is removed from the
dma_device_list and a release callback function is called to signal
the driver to free the memory.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Link: https://lore.kernel.org/r/20191216190120.21374-5-logang@deltatee.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
So it can be called by a release function which is needed higher up in
the code. No functional changes intended.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Link: https://lore.kernel.org/r/20191216190120.21374-4-logang@deltatee.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The module reference is taken to ensure the callbacks still exist
when they are called. If the channel holds the last reference to the
module, the module can disappear before device_free_chan_resources() is
called and would cause a call into free'd memory.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Link: https://lore.kernel.org/r/20191216190120.21374-3-logang@deltatee.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dma_chan_to_owner() dereferences the driver from the struct device to
obtain the owner and call module_[get|put](). However, if the backing
device is unbound before the dma_device is unregistered, the driver
will be cleared and this will cause a NULL pointer dereference.
Instead, store a pointer to the owner module in the dma_device struct
so the module reference can be properly put when the channel is put, even
if the backing device was destroyed first.
This change helps to support a safer unbind of DMA engines.
If the dma_device is unregistered in the driver's remove function,
there's no guarantee that there are no existing clients and a users
action may trigger the WARN_ONCE in dma_async_device_unregister()
which is unlikely to leave the system in a consistent state.
Instead, a better approach is to allow the backing driver to go away
and fail any subsequent requests to it.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Link: https://lore.kernel.org/r/20191216190120.21374-2-logang@deltatee.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- Add support in dmaengine core to do device node checks for DT devices and
update bunch of drivers to use that and remove open coding from drivers
- New driver/driver support for new hardware, namely:
- MediaTek UART APDMA
- Freescale i.mx7ulp edma2
- Synopsys eDMA IP core version 0
- Allwinner H6 DMA
- Updates to axi-dma and support for interleaved cyclic transfers
- Greg's debugfs return value check removals on drivers
- Updates to stm32-dma, hsu, dw, pl330, tegra drivers
-----BEGIN PGP SIGNATURE-----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=R+aC
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- Add support in dmaengine core to do device node checks for DT devices
and update bunch of drivers to use that and remove open coding from
drivers
- New driver/driver support for new hardware, namely:
- MediaTek UART APDMA
- Freescale i.mx7ulp edma2
- Synopsys eDMA IP core version 0
- Allwinner H6 DMA
- Updates to axi-dma and support for interleaved cyclic transfers
- Greg's debugfs return value check removals on drivers
- Updates to stm32-dma, hsu, dw, pl330, tegra drivers
* tag 'dmaengine-5.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (68 commits)
dmaengine: Revert "dmaengine: fsl-edma: add i.mx7ulp edma2 version support"
dmaengine: at_xdmac: check for non-empty xfers_list before invoking callback
Documentation: dmaengine: clean up description of dmatest usage
dmaengine: tegra210-adma: remove PM_CLK dependency
dmaengine: fsl-edma: add i.mx7ulp edma2 version support
dt-bindings: dma: fsl-edma: add new i.mx7ulp-edma
dmaengine: fsl-edma-common: version check for v2 instead
dmaengine: fsl-edma-common: move dmamux register to another single function
dmaengine: fsl-edma: add drvdata for fsl-edma
dmaengine: Revert "dmaengine: fsl-edma: support little endian for edma driver"
dmaengine: rcar-dmac: Reject zero-length slave DMA requests
dmaengine: dw: Enable iDMA 32-bit on Intel Elkhart Lake
dmaengine: dw-edma: fix semicolon.cocci warnings
dmaengine: sh: usb-dmac: Use [] to denote a flexible array member
dmaengine: dmatest: timeout value of -1 should specify infinite wait
dmaengine: dw: Distinguish ->remove() between DW and iDMA 32-bit
dmaengine: fsl-edma: support little endian for edma driver
dmaengine: hsu: Revert "set HSU_CH_MTSR to memory width"
dmagengine: pl330: add code to get reset property
dt-bindings: pl330: document the optional resets property
...
When user try to request one DMA channel by __dma_request_channel(), it won't
validate if it is the correct DMA device to request, that will lead each DMA
engine driver to validate the correct device node in their filter function
if it is necessary.
Thus we can add the matching device node validation in the DMA engine core,
to remove all of device node validation in the drivers.
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details the full
gnu general public license is included in this distribution in the
file called copying
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 9 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.244154651@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch series "Replace all open encodings for NUMA_NO_NODE", v3.
All these places for replacement were found by running the following
grep patterns on the entire kernel code. Please let me know if this
might have missed some instances. This might also have replaced some
false positives. I will appreciate suggestions, inputs and review.
1. git grep "nid == -1"
2. git grep "node == -1"
3. git grep "nid = -1"
4. git grep "node = -1"
This patch (of 2):
At present there are multiple places where invalid node number is
encoded as -1. Even though implicitly understood it is always better to
have macros in there. Replace these open encodings for an invalid node
number with the global macro NUMA_NO_NODE. This helps remove NUMA
related assumptions like 'invalid node' from various places redirecting
them to a common definition.
Link: http://lkml.kernel.org/r/1545127933-10711-2-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> [ixgbe]
Acked-by: Jens Axboe <axboe@kernel.dk> [mtip32xx]
Acked-by: Vinod Koul <vkoul@kernel.org> [dmaengine.c]
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Acked-by: Doug Ledford <dledford@redhat.com> [drivers/infiniband]
Cc: Joseph Qi <jiangqi903@gmail.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull IDA updates from Matthew Wilcox:
"A better IDA API:
id = ida_alloc(ida, GFP_xxx);
ida_free(ida, id);
rather than the cumbersome ida_simple_get(), ida_simple_remove().
The new IDA API is similar to ida_simple_get() but better named. The
internal restructuring of the IDA code removes the bitmap
preallocation nonsense.
I hope the net -200 lines of code is convincing"
* 'ida-4.19' of git://git.infradead.org/users/willy/linux-dax: (29 commits)
ida: Change ida_get_new_above to return the id
ida: Remove old API
test_ida: check_ida_destroy and check_ida_alloc
test_ida: Convert check_ida_conv to new API
test_ida: Move ida_check_max
test_ida: Move ida_check_leaf
idr-test: Convert ida_check_nomem to new API
ida: Start new test_ida module
target/iscsi: Allocate session IDs from an IDA
iscsi target: fix session creation failure handling
drm/vmwgfx: Convert to new IDA API
dmaengine: Convert to new IDA API
ppc: Convert vas ID allocation to new IDA API
media: Convert entity ID allocation to new IDA API
ppc: Convert mmu context allocation to new IDA API
Convert net_namespace to new IDA API
cb710: Convert to new IDA API
rsxx: Convert to new IDA API
osd: Convert to new IDA API
sd: Convert to new IDA API
...
This patch adds the dmaenginem_async_device_register for DMA code.
Use the Devres to call the release for the DMA engine driver.
Signed-off-by: Huang Shijie <sjhuang@iluvatar.ai>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If there are no DMA devices registered yet, return with EPROBE_DEFER
similarly to the case when requesting a slave channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'cmd_pause' DMA channel capability means that respective DMA engine
supports both pausing and resuming given DMA channel. However, in some
cases it is important to know if DMA channel can be paused without the
need to resume it. This is a typical requirement for proper residue
reading on transfer timeout in UART drivers. There are also some DMA
engines with limited hardware, which doesn't really support resuming.
Reporting pause and resume capabilities separately allows UART drivers to
properly check for the really required capabilities and operate in DMA
mode also in systems with limited DMA hardware. On the other hand drivers,
which rely on full channel suspend/resume support, should now check for
both 'pause' and 'resume' features.
Existing clients of dma_get_slave_caps() have been checked and the only
driver which rely on proper channel resuming is soc-generic-dmaengine-pcm
driver, which has been updated to check the newly added capability.
Existing 'cmd_pause' now only indicates that DMA engine support pausing
given DMA channel.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
As files move around, their previous links break. Fix the
references for them.
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
DMAengine core has BUG_ON to check for mandatory operations and ones based
on capabilities, but they use BUG_ON, so remove and move to error returns
and logging the errors gracefully
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There are no in kernel consumers for DMA_SG op. Removing operation,
dead code, and test code in dmatest.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Gary Hook <gary.hook@amd.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Kedareswara rao Appana <appana.durga.rao@xilinx.com>
Cc: Li Yang <leoyang.li@nxp.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This fixes the following warning when building with clang and
CONFIG_DMA_ENGINE_RAID=n :
drivers/dma/dmaengine.c:1102:11: error: array index 2 is past the end of the array (which contains 1 element) [-Werror,-Warray-bounds]
return &unmap_pool[2];
^ ~
drivers/dma/dmaengine.c:1083:1: note: array 'unmap_pool' declared here
static struct dmaengine_unmap_pool unmap_pool[] = {
^
drivers/dma/dmaengine.c:1104:11: error: array index 3 is past the end of the array (which contains 1 element) [-Werror,-Warray-bounds]
return &unmap_pool[3];
^ ~
drivers/dma/dmaengine.c:1083:1: note: array 'unmap_pool' declared here
static struct dmaengine_unmap_pool unmap_pool[] = {
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dmaengine currently uses an IDR to allocate DMA IDs, but it only needs
to know whether IDs are in use or not; the ID to pointer functionality
of the IDR is unused. That means it can use the more space-efficient IDA.
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When check for capabilities recognize slave support by either DMA_SLAVE or
DMA_CYCLIC bit set. If we don't do that the user can't get a normally worked
DMA support for engines that doesn't have one of the mentioned bits set.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit ef859312c3 ("dmaengine: core: Use dev_ functions for debug and
error prints") wasn't quite right in __dma_request_channel() by claiming
that all pr_ prints have valid DMA channel pointer. Obviously it is not
true as __dma_request_channel() is looking for a channel and returns NULL
if it does not find it.
Prevent this potential NULL pointer dereference by reverting back to
pr_debug().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_get_slave_caps() API only checked for slave capability where
we use slave capabilities for cyclic dma operations as well, so we
should add the cyclic case here too.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Dave Jiang