This fixes the jumbo frame support on EMAC V4 systems. Now the correct
bit is set depending on the EMAC version configured.
Tested on Kilauea (405EX) and Canyonlands (460EX).
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Move the "&& skb->ip_summed == CHECKSUM_PARTIAL" part out of
emac_has_feature parameters.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add "ibm,tah" to the compatible matching table of the ibm_newemac
tah driver. The type "tah" is still preserved for compatibility reasons.
New dts files should use the compatible property though.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Problem Description and Fix
---------------------------
When a pause packet(with destination as reserved Multicast address) is
received by the EMAC hardware to control the flow of frames being
transmitted by it, it is dropped by the hardware unless the reserved
Multicast address is hashed in to the GAHT[1-4] registers. This code fix
adds the default reserved multicast address to the GAHT[1-4] registers
in the EMAC(s) present on the chip. The flow control with Pause packets
will only work if the following register bits are programmed in EMAC:
EMACx_MR1[APP] = 1
EMACx_RMR[BAE] = 1
EMACx_RMR[MAE] = 1
Behavior that may be observed in a running system
-------------------------------------------------
A host transferring data from a PPC based system may send a Pause packet
to the PPC EMAC requesting it to slow down the flow of packets. If the
default reserved multicast MAC address is not programmed into the
GAHT[1-4] registers this Pause packet will be dropped by PPC EMAC and no
Flow Control will be done.
Signed-off-by: Pravin M. Bathija <pbathija@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With the removal the the "rgmii-interface" device_type property from the
dts files, the newemac driver needs an update to only rely on compatible
property.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Currently, all non TAH equipped 4xx PPC's call emac_start_xmit() upon
xmit. This routine doesn't check if the frame length exceeds the max.
MAL buffer size.
This patch now changes the driver to call emac_start_xmit_sg() on all
GigE platforms and not only the TAH equipped ones (440GX). This enables
an MTU of 9000 instead 4080.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Similar to of_find_compatible_node(), of_find_matching_node() and
for_each_matching_node() allow you to iterate over the device tree
looking for specific nodes, except that they take of_device_id
tables instead of strings.
This also moves of_match_node() from driver/of/device.c to
driver/of/base.c to colocate it with the of_find_matching_node which
depends on it.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
SPIN_LOCK_UNLOCKED is deprecated, use DEFINE_SPINLOCK instead
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This updates the copyright notices of the new EMAC driver to
avoid confusion as who is to be blamed for new bugs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The patch moves dev_set_drvdata(&ofdev->dev, dev) up before tah_reset(ofdev)
is called to avoid a NULL pointer dereference, since tah_reset uses drvdata.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a typo in ibm_newemac/core.c
(tah_port should be used instead of tah_ph)
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The EMAC4_MR1_OBCI(freq) macro expects freg in MHz,
while opb_bus_freq is kept in Hz. Correct this.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Depending on how the 44x processors are wired, some EMAC cells
might not be useable (and not connected to a PHY). However, some
device-trees may choose to still expose them (since their registers
are present in the MMIO space) but with an "unused" property in them.
Signed-off-by: Hugh Blemings <hugh@blemings.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There are a few variants of the STACR register that affect more than
just the "AXON" version of EMAC. Replace the current test of various
chip models with tests for generic properties in the device-tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
More than just "AXON" version of EMAC RGMII supports MDIO, so replace
the current test with a generic property in the device-tree that
indicates such support.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With some PHYs, when the link goes away, the EMAC reset fails due
to the loss of the RX clock I believe.
The old EMAC driver worked around that using some internal chip-specific
clock force bits that are different on various 44x implementations.
This is an attempt at doing it differently, by avoiding the reset when
there is no link, but forcing loopback mode instead. It seems to work
on my Taishan 440GX based board so far.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When using ZMII for MDIO only (such as 440GX with RGMII for data and ZMII for
MDIO), the ZMII code would fail to properly refcount, thus triggering a
BUG_ON().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This adds support for the Agere ET1011c PHY as found on the AMCC Taishan
board.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds BCM5248 and Marvell 88E1111 PHY support to NEW EMAC driver.
These PHY chips are used on PowerPC 440EPx boards.
The PHY code is based on the previous work by Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It's a bad idea to call flush_scheduled_work from within a
netdev->stop because the linkwatch will occasionally take the
rtnl lock from a workqueue context, and thus that can deadlock.
This reworks things a bit in that area to avoid the problem.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The EMAC driver "fix" was merged by mistake before the dust had settled on
the new napi synchronize interface (and before it got merged). The final
version of that function is spelled without underscores.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
net: Fix new EMAC driver for NAPI changes
This fixes the new EMAC driver for the NAPI updates. The previous patch
by Roland Dreier (already applied) to do that doesn't actually work. This
applies on top of it makes it work on my test Ebony machine.
This patch depends on "net: Add __napi_sycnhronize() to sync with napi poll"
posted previously.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With the base stored in dcr_host_t, there's no need for callers to pass
the dcr_n into dcr_unmap(). In fact this removes the possibility of them
passing the incorrect value, which would then be iounmap()'ed.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that all users of dcr_read()/dcr_write() add the dcr_host_t.base, we
can save them the trouble and do it in dcr_read()/dcr_write().
As some background to why we just went through all this jiggery-pokery,
benh sayeth:
Initially the goal of the dcr_read/dcr_write routines was to operate like
mfdcr/mtdcr which take absolute DCR numbers. The reason is that on 4xx
hardware, indirect DCR access is a pain (goes through a table of
instructions) and it's useful to have the compiler resolve an absolute DCR
inline.
We decided that wasn't worth the API bastardisation since most places
where absolute DCR values are used are low level 4xx-only code which may
as well continue using mfdcr/mtdcr, while the new API is designed for
device "instances" that can exist on 4xx and Axon type platforms and may
be located at variable DCR offsets.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that dcr_host_t contains the base address, we can use that in the
ibm_newemac code, rather than storing it separately.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
... since that sucker is not 32bit-only and on 64bit skb->tail is an
offset, not a pointer.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit da3dedd9 ("[NET]: Make NAPI polling independent of struct
net_device objects.") changed the interface to NAPI polling. Fix up
the ibm_newemac driver so that it works with this new interface. This
is actually a nice cleanup because ibm_newemac is one of the drivers
that wants to have multiple NAPI structures for a single net_device.
Compile-tested only as I don't have a system that uses the ibm_newemac
driver. This conversion the conversion for the ibm_emac driver that
was tested on real PowerPC 440SPe hardware.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs. The
same ASIC is also found in the Axon bridge chip. This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging. Specifically:
- Should be adjusted to properly use the dma mapping API.
Axon needs this.
- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices. The dependencies here between
EMAC, MAL, ZMII etc. make this complicated. At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Stefan Roese