Merge commit e8b364b88c
(PM / Clocks: Do not acquire a mutex under a spinlock) fixing
a regression in drivers/base/power/clock_ops.c.
Conflicts:
drivers/base/power/clock_ops.c
Commit b7ab83e (PM: Use spinlock instead of mutex in clock
management functions) introduced a regression causing clocks_mutex
to be acquired under a spinlock. This happens because
pm_clk_suspend() and pm_clk_resume() call pm_clk_acquire() under
pcd->lock, but pm_clk_acquire() executes clk_get() which causes
clocks_mutex to be acquired. Similarly, __pm_clk_remove(),
executed under pcd->lock, calls clk_put(), which also causes
clocks_mutex to be acquired.
To fix those problems make pm_clk_add() call pm_clk_acquire(), so
that pm_clk_suspend() and pm_clk_resume() don't have to do that.
Change pm_clk_remove() and pm_clk_destroy() to separate
modifications of the pcd->clock_list list from the actual removal of
PM clock entry objects done by __pm_clk_remove().
Reported-and-tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch incorporates the regcache core code into regmap. All previous
patches have been no-ops essentially up to this point.
The bulk read operation is not supported by regcache at the moment. This
will be implemented incrementally.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for LZO compression when storing the register
cache.
For a typical device whose register map would normally occupy 25kB or 50kB
by using the LZO compression technique, one can get down to ~5-7kB. There
might be a performance penalty associated with each individual read/write
due to decompressing/compressing the underlying cache, however that should not
be noticeable. These memory benefits depend on whether the target architecture
can get rid of the memory occupied by the original register defaults cache
which is marked as __devinitconst. Nevertheless there will be some memory
gain even if the target architecture can't get rid of the original register
map, this should be around ~30-32kB instead of 50kB.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the rbtree cache compression type.
Each rbnode manages a variable length block of registers. There can be no
two nodes with overlapping blocks. Each block has a base register and a
currently top register, all the other registers, if any, lie in between these
two and in ascending order.
The reasoning behind the construction of this rbtree is simple. In the
snd_soc_rbtree_cache_init() function, we iterate over the register defaults
provided by the regcache core. For each register value that is non-zero we
insert it in the rbtree. In order to determine in which rbnode we need
to add the register, we first look if there is another register already
added that is adjacent to the one we are about to add. If that is the case
we append it in that rbnode block, otherwise we create a new rbnode
with a single register in its block and add it to the tree.
There are various optimizations across the implementation to speed up lookups
by caching the most recently used rbnode.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is the simplest form of a cache available in regcache. Any
registers whose default value is 0 are ignored. If any of those
registers are modified in the future, they will be placed in the
cache on demand. The cache layout is essentially using the provided
register defaults by the regcache core directly and does not re-map
it to another representation.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch introduces caching support for regmap. The regcache API
has evolved essentially out of ASoC soc-cache so most of the actual
caching types (except LZO) have been tested in the past.
The purpose of regcache is to optimize in time and space the handling
of register caches. Time optimization is achieved by not having to go
over a slow bus like I2C to read the value of a register, instead it is
cached locally in memory and can be retrieved faster. Regarding space
optimization, some of the cache types are better at packing the caches,
for e.g. the rbtree and the LZO caches. By doing this the sacrifice in
time still wins over doing I2C transactions.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make the debugfs stubs static inline to avoid future compilation issues due to
duplicated symbols when CONFIG_DEBUG_FS=n once internal.h is included by
multiple source files.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some buses like SPI have no standard notation of read or write operations.
The general scheme here is to set or clear specific bits in the register
address to indicate whether the operation is a read or write. We already
support having a read flag mask per bus, but as there is no standard
the bits which need to be set or cleared differ between devices and vendors,
thus we need a mechanism to specify them per device.
This patch adds two new entries to the regmap_config struct, read_flag_mask and
write_flag_mask. These will be or'ed onto the top byte when doing a read or
write operation. If both masks are empty the device will fallback to the
regmap_bus masks.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No longer used as users link directly with the bus types so the core
module infrastructure does refcounting for us.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The conversion to per bus type registration functions means we don't need
to do module_get()s to hold the bus types in memory (their users will link
to them) so we removed all those calls. This left module_put() calls in
the cleanup paths which aren't needed and which cause unbalanced puts if
we ever try to unload anything.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
compared to the most powerful and already existing helper (namely
platform_device_register_resndata) this allows to specify a dma_mask.
To make eventual extensions later more easy, a struct holding the used
information is created instead of passing the information by function
parameters.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The generic PM domains framework currently doesn't work with devices
whose power.irq_safe flag is set, because runtime PM callbacks for
such devices are run with interrupts disabled and the callbacks
provided by the generic PM domains framework use domain mutexes
and may sleep. However, such devices very well may belong to
power domains on some systems, so the generic PM domains framework
should take them into account.
For this reason, modify the generic PM domains framework so that the
domain .power_off() and .power_on() callbacks are never executed for
a domain containing devices with power.irq_safe set, although the
.stop_device() and .start_device() callbacks are still run for them.
Additionally, introduce a flag allowing the creator of a
struct generic_pm_domain object to indicate that its .stop_device()
and .start_device() callbacks may be run in interrupt context
(might_sleep_if() triggers if that flag is not set and one of those
callbacks is run in interrupt context).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add a global notification chain that gets called upon changes to the
aggregated constraint value for any device.
The notification callbacks are passing the full constraint request data
in order for the callees to have access to it. The current use is for the
platform low-level code to access the target device of the constraint.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Implement the per-device PM QoS constraints by creating a device
PM QoS API, which calls the PM QoS constraints management core code.
The per-device latency constraints data strctures are stored
in the device dev_pm_info struct.
The device PM code calls the init and destroy of the per-device constraints
data struct in order to support the dynamic insertion and removal of the
devices in the system.
To minimize the data usage by the per-device constraints, the data struct
is only allocated at the first call to dev_pm_qos_add_request.
The data is later free'd when the device is removed from the system.
A global mutex protects the constraints users from the data being
allocated and free'd.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Since the PM clock management code in drivers/base/power/clock_ops.c
is used for both runtime PM and system suspend/hibernation, the
definitions of data structures and headers related to it should not
be located in include/linux/pm_rumtime.h. Move them to a separate
header file.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Currently pm_genpd_runtime_resume() has to walk the list of devices
from the device's PM domain to find the corresponding device list
object containing the need_restore field to check if the driver's
.runtime_resume() callback should be executed for the device.
This is suboptimal and can be simplified by using power.sybsys_data
to store device information used by the generic PM domains code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Since the power.subsys_data device field will be used by multiple
filesystems, introduce a reference counting mechanism for it to avoid
freeing it prematurely or changing its value at a wrong time.
Make the PM clocks management code that currently is the only user of
power.subsys_data use the new reference counting.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Introduce struct pm_subsys_data that may be subclassed by subsystems
to store subsystem-specific information related to the device. Move
the clock management fields accessed through the power.subsys_data
pointer in struct device to the new strucutre.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Change the name of the second argument of pm_genpd_add_subdomain()
so that it is (a) shorter and (b) in agreement with the name of
the second argument of pm_genpd_add_subdomain().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Since it is now possible for a PM domain to have multiple masters
instead of one parent, rename the "wait for parent" status to reflect
the new situation.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Currently, for a given generic PM domain there may be only one parent
domain (i.e. a PM domain it depends on). However, there is at least
one real-life case in which there should be two parents (masters) for
one PM domain (the A3RV domain on SH7372 turns out to depend on the
A4LC domain and it depends on the A4R domain and the same time). For
this reason, allow a PM domain to have multiple parents (masters) by
introducing objects representing links between PM domains.
The (logical) links between PM domains represent relationships in
which one domain is a master (i.e. it is depended on) and another
domain is a slave (i.e. it depends on the master) with the rule that
the slave cannot be powered on if the master is not powered on and
the master cannot be powered off if the slave is not powered off.
Each struct generic_pm_domain object representing a PM domain has
two lists of links, a list of links in which it is a master and
a list of links in which it is a slave. The first of these lists
replaces the list of subdomains and the second one is used in place
of the parent pointer.
Each link is represented by struct gpd_link object containing
pointers to the master and the slave and two struct list_head
members allowing it to hook into two lists (the master's list
of "master" links and the slave's list of "slave" links). This
allows the code to get to the link from each side (either from
the master or from the slave) and follow it in each direction.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The next patch will make it possible for a generic PM domain to have
multiple parents (i.e. multiple PM domains it depends on). To
prepare for that change it is necessary to change pm_genpd_poweron()
so that it doesn't jump to the start label after running itself
recursively for the parent domain. For this purpose, introduce a new
PM domain status value GPD_STATE_WAIT_PARENT that will be set by
pm_genpd_poweron() before calling itself recursively for the parent
domain and modify the code in drivers/base/power/domain.c so that
the GPD_STATE_WAIT_PARENT status is guaranteed to be preserved during
the execution of pm_genpd_poweron() for the parent.
This change also causes pm_genpd_add_subdomain() and
pm_genpd_remove_subdomain() to wait for started pm_genpd_poweron() to
complete and allows pm_genpd_runtime_resume() to avoid dropping the
lock after powering on the PM domain.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If pm_genpd_remove_subdomain() is called to remove a PM domain's
subdomain and pm_genpd_poweron() is called for that subdomain at
the same time, and the pm_genpd_poweron() called by it recursively
for the parent returns an error, the first pm_genpd_poweron()'s
error code path will attempt to decrement the subdomain counter of
a PM domain that it's not a subdomain of any more.
Rearrange the code in pm_genpd_poweron() to prevent this from
happening.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
After the subdomain counter in struct generic_pm_domain has been
changed into an atomic_t field, it is possible to modify
pm_genpd_poweron() and pm_genpd_poweroff() so that they don't take
the parents locks. This requires pm_genpd_poweron() to increment
the parent's subdomain counter before calling itself recursively
for the parent and to decrement it if an error is to be returned.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Currently, pm_genpd_poweron() and pm_genpd_poweroff() need to take
the parent PM domain's lock in order to modify the parent's counter
of active subdomains in a nonracy way. This causes the locking to be
considerably complex and in fact is not necessary, because the
subdomain counters may be implemented as atomic fields and they
won't have to be modified under a lock.
Replace the unsigned in sd_count field in struct generic_pm_domain
by an atomic_t one and modify the code in drivers/base/power/domain.c
to take this change into account.
This patch doesn't change the locking yet, that is going to be done
in a separate subsequent patch.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
In commit a144c6a6c9 ("PM: Print a warning if firmware is requested
when tasks are frozen") we not only printed a warning if somebody tried
to load the firmware when tasks are frozen - we also failed the load.
But that check was done before the check for built-in firmware, and then
when we disallowed usermode helpers during bootup (commit 288d5abec831:
"Boot up with usermodehelper disabled"), that actually means that
built-in modules can no longer load their firmware even if the firmware
is built in too. Which used to work, and some people depended on it for
the R100 driver.
So move the test for usermodehelper_is_disabled() down, to after
checking the built-in firmware.
This should fix:
https://bugzilla.kernel.org/show_bug.cgi?id=40952
Reported-by: James Cloos <cloos@hjcloos.com>
Bisected-by: Elimar Riesebieter <riesebie@lxtec.de>
Cc: Michel Dänzer <michel@daenzer.net>
Cc: Rafael Wysocki <rjw@sisk.pl>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The lock member of struct pm_clk_data is of type struct mutex,
which is a problem, because the suspend and resume routines
defined in drivers/base/power/clock_ops.c cannot be executed
with interrupts disabled for this reason. Modify
struct pm_clk_data so that its lock member is a spinlock.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Unlike dynamic_pr_debug, dynamic uses of dev_dbg can not
currently add task_pid/KBUILD_MODNAME/__func__/__LINE__
to selected debug output.
Add a new function similar to dynamic_pr_debug to
optionally emit these prefixes.
Cc: Aloisio Almeida <aloisio.almeida@openbossa.org>
Noticed-by: Aloisio Almeida <aloisio.almeida@openbossa.org>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If id_entry is available then it is used. However if we remove first the
driver followed by the device, then the id_entry is pointing to driver's
memory which is long gone.
Since id->name and plat->name are equal there is no point in
distinguishing them.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
devres_release_all and devres_release_group both aquire the lock
&dev->devres_lock but the release of that lock is done in release_nodes.
This results in sparse noise about context imbalance.
Add a lock annotation to release_nodes to quiet this noise.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit b33f9cbd67 ("regmap: Specify a module license") added a
MODULES_LICENSE to this file without adding an include of module.h.
module.h should have been included anyway, since this file has
EXPORT_SYMBOLs as well. With the pending module.h split up, this would
probably have caused build problems.
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some of the entry points to pm runtime are not safe to
call in atomic context unless pm_runtime_irq_safe() has
been called. Inspecting the code, it is not immediately
obvious that the functions sleep at all, as they run
inside a spin_lock_irqsave, but under some conditions
they can drop the lock and turn on irqs.
If a driver incorrectly calls the pm_runtime apis, it can
cause sleeping and irq processing when it expects to stay
in atomic context.
Add might_sleep_if to the majority of the __pm_runtime_* entry points
to enforce correct usage.
Add pm_runtime_put_sync_autosuspend to the list of
functions that can be called in atomic context.
Signed-off-by: Colin Cross <ccross@android.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Function genpd_queue_power_off_work() is not defined for
CONFIG_PM_RUNTIME, so pm_genpd_poweroff_unused() causes a build
error to happen in that case. Fix the problem by making
pm_genpd_poweroff_unused() depend on CONFIG_PM_RUNTIME too.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Let userspace know what the access map for the device is. This is helpful
for verifying that the access map is correctly configured and could also
be useful for programs that try to work with the data. File format is:
register: R W V P
where R, W, V and P are 'y' or 'n' showing readable, writable, volatile
and precious respectively.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We're going to be using these in quite a few places so factor out the
readable/writable/volatile/precious checks.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_REGMAP_I2C/SPI are set to m when selected by a tristate config
option that's set to m. The regmap modules don't specify a license, so
fail to link to regmap_init at load time, since that is EXPORT_SYMBOL_GPL.
Fix this by specifying a license for the regmap modules.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
x86_64 size_t is not an int but the printf format specifier for size_t
should be an int.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
This fixes the following section mismatch issue:
WARNING: vmlinux.o(.text+0x1192bf): Section mismatch in reference from the function devtmpfsd() to the variable .init.data:setup_done
The function devtmpfsd() references the variable __initdata setup_done.
This is often because devtmpfsd lacks a __initdata annotation or the annotation of setup_done is wrong.
WARNING: vmlinux.o(.text+0x119342): Section mismatch in reference from the function devtmpfsd() to the variable .init.data:setup_done
The function devtmpfsd() references the variable __initdata setup_done.
This is often because devtmpfsd lacks a __initdata annotation or the annotation of setup_done is wrong.
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Warning(drivers/base/platform.c:50): No description found for parameter 'pdev'
Warning(drivers/base/platform.c:50): Excess function parameter 'dev' description in 'arch_setup_pdev_archdata'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Copy over the read parts of the ASoC debugfs implementation into regmap,
allowing users to see what the register values the device has are at
runtime. The implementation, especially the support for seeking, is
mostly due to Dimitris Papastamos' work in ASoC.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is mainly intended to be used by devices which can dynamically
block register writes at runtime, for other devices there is usually
limited value.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Trace single register reads and writes, plus start/stop tracepoints for
the actual I/O to see where we're spending time. This makes it easy to
have always on logging without overwhelming the logs and also lets us take
advantage of all the context and time information that the trace subsystem
collects for us.
We don't currently trace register values for bulk operations as this would
add complexity and overhead parsing the cooked data that's being worked
with.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When doing a single register write we use work_buf for both the register
and the value with the buffer formatted for sending directly to the device
so we can just do a write() directly. This saves allocating a temporary
buffer if we can't do gather writes and is likely to be faster than doing
a gather write.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is currently unused but we need to know which registers exist and
their properties in order to implement diagnostics like register map
dumps and the cache features.
We use callbacks partly because properties can vary at runtime (eg, through
access locks on registers) and partly because big switch statements are a
good compromise between readable code and small data size for providing
information on big register maps.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the use of pm_runtime_put_sync() is not safe from
interrupts-disabled context because rpm_idle() will release the
spinlock and enable interrupts for the idle callbacks. This enables
interrupts during a time where interrupts were expected to be
disabled, and can have strange side effects on drivers that expected
interrupts to be disabled.
This is not a bug since the documentation clearly states that only
_put_sync_suspend() is safe in IRQ-safe mode.
However, pm_runtime_put_sync() could be made safe when in IRQ-safe
mode by releasing the spinlock but not re-enabling interrupts, which
is what this patch aims to do.
Problem was found when using some buggy drivers that set
pm_runtime_irq_safe() and used _put_sync() in interrupts-disabled
context.
Reported-by: Colin Cross <ccross@google.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The local variable ret is defined twice in pm_genpd_poweron(), which
causes this function to always return 0, even if the PM domain's
.power_on() callback fails, in which case an error code should be
returned.
Remove the wrong second definition of ret and additionally remove an
unnecessary definition of wait from pm_genpd_poweron().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
create_path() on something without a single / in it will return err
without initializing it. It actually can't happen (we call that thing
only if create on the same path returns -ENOENT, which won't happen
happen for single-component path), but in this case initializing err
to 0 is more than making compiler to STFU - would be the right thing
to return on such paths; the function creates a parent directory of
given pathname and in that case it has no work to do...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dev_opp initial value shoule be ERR_PTR(), IS_ERR() is used to check
error.
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
updated Documentation/ja_JP/SubmittingPatches
debugfs: add documentation for debugfs_create_x64
uio: uio_pdrv_genirq: Add OF support
firmware: gsmi: remove sysfs entries when unload the module
Documentation/zh_CN: Fix messy code file email-clients.txt
driver core: add more help description for "path to uevent helper"
driver-core: modify FIRMWARE_IN_KERNEL help message
driver-core: Kconfig grammar corrections in firmware configuration
DOCUMENTATION: Replace create_device() with device_create().
DOCUMENTATION: Update overview.txt in Doc/driver-model.
pti: pti_tty_install documentation mispelling.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (99 commits)
drivers/virt: add missing linux/interrupt.h to fsl_hypervisor.c
powerpc/85xx: fix mpic configuration in CAMP mode
powerpc: Copy back TIF flags on return from softirq stack
powerpc/64: Make server perfmon only built on ppc64 server devices
powerpc/pseries: Fix hvc_vio.c build due to recent changes
powerpc: Exporting boot_cpuid_phys
powerpc: Add CFAR to oops output
hvc_console: Add kdb support
powerpc/pseries: Fix hvterm_raw_get_chars to accept < 16 chars, fixing xmon
powerpc/irq: Quieten irq mapping printks
powerpc: Enable lockup and hung task detectors in pseries and ppc64 defeconfigs
powerpc: Add mpt2sas driver to pseries and ppc64 defconfig
powerpc: Disable IRQs off tracer in ppc64 defconfig
powerpc: Sync pseries and ppc64 defconfigs
powerpc/pseries/hvconsole: Fix dropped console output
hvc_console: Improve tty/console put_chars handling
powerpc/kdump: Fix timeout in crash_kexec_wait_realmode
powerpc/mm: Fix output of total_ram.
powerpc/cpufreq: Add cpufreq driver for Momentum Maple boards
powerpc: Correct annotations of pmu registration functions
...
Fix up trivial Kconfig/Makefile conflicts in arch/powerpc, drivers, and
drivers/cpufreq
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
fs: take the ACL checks to common code
bury posix_acl_..._masq() variants
kill boilerplates around posix_acl_create_masq()
generic_acl: no need to clone acl just to push it to set_cached_acl()
kill boilerplate around posix_acl_chmod_masq()
reiserfs: cache negative ACLs for v1 stat format
xfs: cache negative ACLs if there is no attribute fork
9p: do no return 0 from ->check_acl without actually checking
vfs: move ACL cache lookup into generic code
CIFS: Fix oops while mounting with prefixpath
xfs: Fix wrong return value of xfs_file_aio_write
fix devtmpfs race
caam: don't pass bogus S_IFCHR to debugfs_create_...()
get rid of create_proc_entry() abuses - proc_mkdir() is there for purpose
asus-wmi: ->is_visible() can't return negative
fix jffs2 ACLs on big-endian with 16bit mode_t
9p: close ACL leaks
ocfs2_init_acl(): fix a leak
VFS : mount lock scalability for internal mounts
After we's done complete(&req->done), there's nothing to prevent the
scope containing *req from being gone and *req overwritten by any
kind of junk. So we must read req->next before that...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We should be reading the number of bytes we were asked for, not the size
of a single register.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regulator: Convert tps65023 to use regmap API
regmap: Add SPI bus support
regmap: Add I2C bus support
regmap: Add generic non-memory mapped register access API
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
There are many places in the tree where we implement register access for
devices on non-memory mapped buses, especially I2C and SPI. Since hardware
designers seem to have settled on a relatively consistent set of register
interfaces this can be effectively factored out into shared code. There
are a standard set of formats for marshalling data for exchange with the
device, with the actual I/O mechanisms generally being simple byte
streams.
We create an abstraction for marshaling data into formats which can be
sent on the control interfaces, and create a standard method for
plugging in actual transport underneath that.
This is mostly a refactoring and renaming of the bottom level of the
existing code for sharing register I/O which we have in ASoC. A
subsequent patch in this series converts ASoC to use this. The main
difference in interface is that reads return values by writing to a
location provided by a pointer rather than in the return value, ensuring
we can use the full range of the type for register data. We also use
unsigned types rather than ints for the same reason.
As some of the devices can have very large register maps the existing
ASoC code also contains infrastructure for managing register caches.
This cache work will be moved over in a future stage to allow for
separate review, the current patch only deals with the physical I/O.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (107 commits)
vfs: use ERR_CAST for err-ptr tossing in lookup_instantiate_filp
isofs: Remove global fs lock
jffs2: fix IN_DELETE_SELF on overwriting rename() killing a directory
fix IN_DELETE_SELF on overwriting rename() on ramfs et.al.
mm/truncate.c: fix build for CONFIG_BLOCK not enabled
fs:update the NOTE of the file_operations structure
Remove dead code in dget_parent()
AFS: Fix silly characters in a comment
switch d_add_ci() to d_splice_alias() in "found negative" case as well
simplify gfs2_lookup()
jfs_lookup(): don't bother with . or ..
get rid of useless dget_parent() in btrfs rename() and link()
get rid of useless dget_parent() in fs/btrfs/ioctl.c
fs: push i_mutex and filemap_write_and_wait down into ->fsync() handlers
drivers: fix up various ->llseek() implementations
fs: handle SEEK_HOLE/SEEK_DATA properly in all fs's that define their own llseek
Ext4: handle SEEK_HOLE/SEEK_DATA generically
Btrfs: implement our own ->llseek
fs: add SEEK_HOLE and SEEK_DATA flags
reiserfs: make reiserfs default to barrier=flush
...
Fix up trivial conflicts in fs/xfs/linux-2.6/xfs_super.c due to the new
shrinker callout for the inode cache, that clashed with the xfs code to
start the periodic workers later.
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
iommu/core: Fix build with INTR_REMAP=y && CONFIG_DMAR=n
iommu/amd: Don't use MSI address range for DMA addresses
iommu/amd: Move missing parts to drivers/iommu
iommu: Move iommu Kconfig entries to submenu
x86/ia64: intel-iommu: move to drivers/iommu/
x86: amd_iommu: move to drivers/iommu/
msm: iommu: move to drivers/iommu/
drivers: iommu: move to a dedicated folder
x86/amd-iommu: Store device alias as dev_data pointer
x86/amd-iommu: Search for existind dev_data before allocting a new one
x86/amd-iommu: Allow dev_data->alias to be NULL
x86/amd-iommu: Use only dev_data in low-level domain attach/detach functions
x86/amd-iommu: Use only dev_data for dte and iotlb flushing routines
x86/amd-iommu: Store ATS state in dev_data
x86/amd-iommu: Store devid in dev_data
x86/amd-iommu: Introduce global dev_data_list
x86/amd-iommu: Remove redundant device_flush_dte() calls
iommu-api: Add missing header file
Fix up trivial conflicts (independent additions close to each other) in
drivers/Makefile and include/linux/pci.h
We do _NOT_ want to mkdir the path itself - we are preparing to
mknod it, after all. Normally it'll fail with -ENOENT and
just do nothing, but if somebody has created the parent in
the meanwhile, we'll get buggered...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
... and give it a namespace where devtmpfs would be mounted on root,
thus avoiding abuses of vfs_path_lookup() (it was never intended to
be used with LOOKUP_PARENT). Games with credentials are also gone.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* pm-runtime:
OMAP: PM: disable idle on suspend for GPIO and UART
OMAP: PM: omap_device: add API to disable idle on suspend
OMAP: PM: omap_device: add system PM methods for PM domain handling
OMAP: PM: omap_device: conditionally use PM domain runtime helpers
PM / Runtime: Add new helper function: pm_runtime_status_suspended()
PM / Runtime: Consistent utilization of deferred_resume
PM / Runtime: Prevent runtime_resume from racing with probe
PM / Runtime: Replace "run-time" with "runtime" in documentation
PM / Runtime: Improve documentation of enable, disable and barrier
PM: Limit race conditions between runtime PM and system sleep (v2)
PCI / PM: Detect early wakeup in pci_pm_prepare()
PM / Runtime: Return special error code if runtime PM is disabled
PM / Runtime: Update documentation of interactions with system sleep
* pm-domains: (33 commits)
ARM / shmobile: Return -EBUSY from A4LC power off if A3RV is active
PM / Domains: Take .power_off() error code into account
ARM / shmobile: Use genpd_queue_power_off_work()
ARM / shmobile: Use pm_genpd_poweroff_unused()
PM / Domains: Introduce function to power off all unused PM domains
PM / Domains: Queue up power off work only if it is not pending
PM / Domains: Improve handling of wakeup devices during system suspend
PM / Domains: Do not restore all devices on power off error
PM / Domains: Allow callbacks to execute all runtime PM helpers
PM / Domains: Do not execute device callbacks under locks
PM / Domains: Make failing pm_genpd_prepare() clean up properly
PM / Domains: Set device state to "active" during system resume
ARM: mach-shmobile: sh7372 A3RV requires A4LC
PM / Domains: Export pm_genpd_poweron() in header
ARM: mach-shmobile: sh7372 late pm domain off
ARM: mach-shmobile: Runtime PM late init callback
ARM: mach-shmobile: sh7372 D4 support
ARM: mach-shmobile: sh7372 A4MP support
ARM: mach-shmobile: sh7372: make sure that fsi is peripheral of spu2
ARM: mach-shmobile: sh7372 A3SG support
...
Some users are apparently confused by dmesg output from
read_magic_time(), which looks like "real" time and date.
Add the "RTC" string to time stamps printed by read_magic_time() to
avoid that confusion.
Reported-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
cpufreq table allocated by opp_init_cpufreq_table is better
freed by OPP layer itself. This allows future modifications to
the table handling to be transparent to the users.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Currently pm_genpd_poweroff() discards error codes returned by
the PM domain's .power_off() callback, because it's safer to always
regard the domain as inaccessible to drivers after a failing
.power_off(). Still, there are situations in which the low-level
code may want to indicate that it doesn't want to power off the
domain, so allow it to do that by returning -EBUSY from .power_off().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Make pd_power_down_a3rv() use genpd_queue_power_off_work() to queue
up the powering off of the A4LC domain to avoid queuing it up when
it is pending.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Add a new function pm_genpd_poweroff_unused() queuing up the
execution of pm_genpd_poweroff() for every initialized generic PM
domain. Calling it will cause every generic PM domain without
devices in use to be powered off.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The macro MIN_MEMORY_BLOCK_SIZE is currently defined twice in two .c
files, and I need it in a third one to fix a powerpc bug, so let's
first move it into a header
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
In theory it is possible that pm_genpd_poweroff() for two different
subdomains of the same parent domain will attempt to queue up the
execution of pm_genpd_poweroff() for the parent twice in a row. This
would lead to unpleasant consequences, so prevent it from happening
by checking if genpd->power_off_work is pending before attempting to
queue it up.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Kevin points out that if there's a device that can wake up the system
from sleep states, but it doesn't generate wakeup signals by itself
(they are generated on its behalf by other parts of the system) and
it currently is not enabled to wake up the system (that is,
device_may_wakeup() returns "false" for it), we may need to change
its wakeup settings during system suspend (for example, the device
might have been configured to signal remote wakeup from the system's
working state, as needed by runtime PM). Therefore the generic PM
domains code should invoke the system suspend callbacks provided by
the device's driver, which it doesn't do if the PM domain is powered
off during the system suspend's "prepare" stage. This is a valid
point. Moreover, this code also should make sure that system wakeup
devices that are enabled to wake up the system from sleep states and
have to remain active for this purpose are not suspended while the
system is in a sleep state.
To avoid the above issues, make the generic PM domains' .prepare()
routine, pm_genpd_prepare(), force runtime resume of devices whose
system wakeup settings may need to be changed during system suspend
or that should remain active while the system is in a sleep state to
be able to wake it up from that state.
Reported-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Since every device in a PM domain has its own need_restore
flag, which is set by __pm_genpd_save_device(), there's no need to
walk the domain's device list and restore all devices on an error
from one of the drivers' .runtime_suspend() callbacks.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
A deadlock may occur if one of the PM domains' .start_device() or
.stop_device() callbacks or a device driver's .runtime_suspend() or
.runtime_resume() callback executed by the core generic PM domain
code uses a "wrong" runtime PM helper function. This happens, for
example, if .runtime_resume() from one device's driver calls
pm_runtime_resume() for another device in the same PM domain.
A similar situation may take place if a device's parent is in the
same PM domain, in which case the runtime PM framework may execute
pm_genpd_runtime_resume() automatically for the parent (if it is
suspended at the moment). This, of course, is undesirable, so
the generic PM domains code should be modified to prevent it from
happening.
The runtime PM framework guarantees that pm_genpd_runtime_suspend()
and pm_genpd_runtime_resume() won't be executed in parallel for
the same device, so the generic PM domains code need not worry
about those cases. Still, it needs to prevent the other possible
race conditions between pm_genpd_runtime_suspend(),
pm_genpd_runtime_resume(), pm_genpd_poweron() and pm_genpd_poweroff()
from happening and it needs to avoid deadlocks at the same time.
To this end, modify the generic PM domains code to relax
synchronization rules so that:
* pm_genpd_poweron() doesn't wait for the PM domain status to
change from GPD_STATE_BUSY. If it finds that the status is
not GPD_STATE_POWER_OFF, it returns without powering the domain on
(it may modify the status depending on the circumstances).
* pm_genpd_poweroff() returns as soon as it finds that the PM
domain's status changed from GPD_STATE_BUSY after it's released
the PM domain's lock.
* pm_genpd_runtime_suspend() doesn't wait for the PM domain status
to change from GPD_STATE_BUSY after executing the domain's
.stop_device() callback and executes pm_genpd_poweroff() only
if pm_genpd_runtime_resume() is not executed in parallel.
* pm_genpd_runtime_resume() doesn't wait for the PM domain status
to change from GPD_STATE_BUSY after executing pm_genpd_poweron()
and sets the domain's status to GPD_STATE_BUSY and increments its
counter of resuming devices (introduced by this change) immediately
after acquiring the lock. The counter of resuming devices is then
decremented after executing __pm_genpd_runtime_resume() for the
device and the domain's status is reset to GPD_STATE_ACTIVE (unless
there are more resuming devices in the domain, in which case the
status remains GPD_STATE_BUSY).
This way, for example, if a device driver's .runtime_resume()
callback executes pm_runtime_resume() for another device in the same
PM domain, pm_genpd_poweron() called by pm_genpd_runtime_resume()
invoked by the runtime PM framework will not block and it will see
that there's nothing to do for it. Next, the PM domain's lock will
be acquired without waiting for its status to change from
GPD_STATE_BUSY and the device driver's .runtime_resume() callback
will be executed. In turn, if pm_runtime_suspend() is executed by
one device driver's .runtime_resume() callback for another device in
the same PM domain, pm_genpd_poweroff() executed by
pm_genpd_runtime_suspend() invoked by the runtime PM framework as a
result will notice that one of the devices in the domain is being
resumed, so it will return immediately.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Currently, the .start_device() and .stop_device() callbacks from
struct generic_pm_domain() as well as the device drivers' runtime PM
callbacks used by the generic PM domains code are executed under
the generic PM domain lock. This, unfortunately, is prone to
deadlocks, for example if a device and its parent are boths members
of the same PM domain. For this reason, it would be better if the
PM domains code didn't execute device callbacks under the lock.
Rework the locking in the generic PM domains code so that the lock
is dropped for the execution of device callbacks. To this end,
introduce PM domains states reflecting the current status of a PM
domain and such that the PM domain lock cannot be acquired if the
status is GPD_STATE_BUSY. Make threads attempting to acquire a PM
domain's lock wait until the status changes to either
GPD_STATE_ACTIVE or GPD_STATE_POWER_OFF.
This change by itself doesn't fix the deadlock problem mentioned
above, but the mechanism introduced by it will be used for for this
purpose by a subsequent patch.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If pm_generic_prepare() in pm_genpd_prepare() returns error code,
the PM domains counter of "prepared" devices should be decremented
and its suspend_power_off flag should be reset if this counter drops
down to zero. Otherwise, the PM domain runtime PM code will not
handle the domain correctly (it will permanently think that system
suspend is in progress).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The runtime PM status of devices in a power domain that is not
powered off in pm_genpd_complete() should be set to "active", because
those devices are operational at this point. Some of them may not be
in use, though, so make pm_genpd_complete() call pm_runtime_idle()
in addition to pm_runtime_set_active() for each of them.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Patch 2e711c04db
(PM: Remove sysdev suspend, resume and shutdown operations)
deleted sysdev_suspend(), which was being relied on to call
check_wakeup_irqs() in suspend. If check_wakeup_irqs() is not
called, wake interrupts that are pending when suspend is
entered may be lost. It also breaks IRQCHIP_MASK_ON_SUSPEND,
which is handled in check_wakeup_irqs().
This patch adds a call to check_wakeup_irqs() in syscore_suspend(),
similar to what was deleted in sysdev_suspend().
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
dev->power.deferred_resume is used as a bool typically, so change
one assignment to false from 0, like other places.
Signed-off-by: ShuoX Liu <shuox.liu@intel.com>
On some architectures we need to setup pdev_archdata before we add the
device. Waiting til a bus_notifier is too late since we might need the
pdev_archdata in the bus notifier. One example is setting up of dma_mask
pointers such that it can be used in a bus_notifier.
We add weak noop version of arch_setup_pdev_archdata() and allow the arch
code to override with access the full definitions of struct device,
struct platform_device, and struct pdev_archdata.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch (as1475) adds device_lock() and device_unlock() calls to
the store methods for the power/control and power/autosuspend_delay_ms
sysfs attribute files. We don't want badly timed writes to these
files to cause runtime_resume callbacks to occur while a driver is
being probed for a device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The runtime PM documentation and kerneldoc comments sometimes spell
"runtime" with a dash (i.e. "run-time"). Replace all of those
instances with "runtime" to make the naming consistent.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
One of the roles of the PM core is to prevent different PM callbacks
executed for the same device object from racing with each other.
Unfortunately, after commit e866500247
(PM: Allow pm_runtime_suspend() to succeed during system suspend)
runtime PM callbacks may be executed concurrently with system
suspend/resume callbacks for the same device.
The main reason for commit e866500247
was that some subsystems and device drivers wanted to use runtime PM
helpers, pm_runtime_suspend() and pm_runtime_put_sync() in
particular, for carrying out the suspend of devices in their
.suspend() callbacks. However, as it's been determined recently,
there are multiple reasons not to do so, inlcuding:
* The caller really doesn't control the runtime PM usage counters,
because user space can access them through sysfs and effectively
block runtime PM. That means using pm_runtime_suspend() or
pm_runtime_get_sync() to suspend devices during system suspend
may or may not work.
* If a driver calls pm_runtime_suspend() from its .suspend()
callback, it causes the subsystem's .runtime_suspend() callback to
be executed, which leads to the call sequence:
subsys->suspend(dev)
driver->suspend(dev)
pm_runtime_suspend(dev)
subsys->runtime_suspend(dev)
recursive from the subsystem's point of view. For some subsystems
that may actually work (e.g. the platform bus type), but for some
it will fail in a rather spectacular fashion (e.g. PCI). In each
case it means a layering violation.
* Both the subsystem and the driver can provide .suspend_noirq()
callbacks for system suspend that can do whatever the
.runtime_suspend() callbacks do just fine, so it really isn't
necessary to call pm_runtime_suspend() during system suspend.
* The runtime PM's handling of wakeup devices is usually different
from the system suspend's one, so .runtime_suspend() may simply be
inappropriate for system suspend.
* System suspend is supposed to work even if CONFIG_PM_RUNTIME is
unset.
* The runtime PM workqueue is frozen before system suspend, so if
whatever the driver is going to do during system suspend depends
on it, that simply won't work.
Still, there is a good reason to allow pm_runtime_resume() to
succeed during system suspend and resume (for instance, some
subsystems and device drivers may legitimately use it to ensure that
their devices are in full-power states before suspending them).
Moreover, there is no reason to prevent runtime PM callbacks from
being executed in parallel with the system suspend/resume .prepare()
and .complete() callbacks and the code removed by commit
e866500247 went too far in this
respect. On the other hand, runtime PM callbacks, including
.runtime_resume(), must not be executed during system suspend's
"late" stage of suspending devices and during system resume's "early"
device resume stage.
Taking all of the above into consideration, make the PM core
acquire a runtime PM reference to every device and resume it if
there's a runtime PM resume request pending right before executing
the subsystem-level .suspend() callback for it. Make the PM core
drop references to all devices right after executing the
subsystem-level .resume() callbacks for them. Additionally,
make the PM core disable the runtime PM framework for all devices
during system suspend, after executing the subsystem-level .suspend()
callbacks for them, and enable the runtime PM framework for all
devices during system resume, right before executing the
subsystem-level .resume() callbacks for them.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Kevin Hilman <khilman@ti.com>
Some callers of pm_runtime_get_sync() and other runtime PM helper
functions, scsi_autopm_get_host() and scsi_autopm_get_device() in
particular, need to distinguish error codes returned when runtime PM
is disabled (i.e. power.disable_depth is nonzero for the given
device) from error codes returned in other situations. For this
reason, make the runtime PM helper functions return -EACCES when
power.disable_depth is nonzero and ensure that this error code
won't be returned by them in any other circumstances. Modify
scsi_autopm_get_host() and scsi_autopm_get_device() to check the
error code returned by pm_runtime_get_sync() and ignore -EACCES.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The common PM clock management functions may be used for system
suspend/resume as well as for runtime PM, so rename them
accordingly. Modify kerneldoc comments describing these functions
and kernel messages printed by them, so that they refer to power
management in general rather that to runtime PM.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
The common clocks management code in drivers/base/power/clock_ops.c
is going to be used during system-wide power transitions as well as
for runtime PM, so it shouldn't depend on CONFIG_PM_RUNTIME.
However, the suspend/resume functions provided by it for
CONFIG_PM_RUNTIME unset, to be used during system-wide power
transitions, should not behave in the same way as their counterparts
defined for CONFIG_PM_RUNTIME set, because in that case the clocks
are managed differently at run time.
The names of the functions still contain the word "runtime" after
this change, but that is going to be modified by a separate patch
later.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
There is the problem how to handle devices set up to wake up the
system from sleep states during system-wide power transitions.
In some cases, those devices can be turned off entirely, because the
wakeup signals will be generated on their behalf anyway. In some
other cases, they will generate wakeup signals if their clocks are
stopped, but only if power is not removed from them. Finally, in
some cases, they can only generate wakeup signals if power is not
removed from them and their clocks are enabled.
To allow platform-specific code to decide whether or not to put
wakeup devices (and their PM domains) into low-power state during
system-wide transitions, such as system suspend, introduce a new
generic PM domain callback, .active_wakeup(), that will be used
during the "noirq" phase of system suspend and hibernation (after
image creation) to decide what to do with wakeup devices.
Specifically, if this callback is present and returns "true", the
generic PM domain code will not execute .stop_device() for the
given wakeup device and its PM domain won't be powered off.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Kevin Hilman <khilman@ti.com>
Make generic PM domains support system-wide power transitions
(system suspend and hibernation). Add suspend, resume, freeze, thaw,
poweroff and restore callbacks to be associated with struct
generic_pm_domain objects and make pm_genpd_init() use them as
appropriate.
The new callbacks do nothing for devices belonging to power domains
that were powered down at run time (before the transition). For the
other devices the action carried out depends on the type of the
transition. During system suspend the power domain .suspend()
callback executes pm_generic_suspend() for the device, while the
PM domain .suspend_noirq() callback runs pm_generic_suspend_noirq()
for it, stops it and eventually removes power from the PM domain it
belongs to (after all devices in the domain have been stopped and its
subdomains have been powered off).
During system resume the PM domain .resume_noirq() callback
restores power to the PM domain (when executed for it first time),
starts the device and executes pm_generic_resume_noirq() for it,
while the .resume() callback executes pm_generic_resume() for the
device. Finally, the .complete() callback executes pm_runtime_idle()
for the device which should put it back into the suspended state if
its runtime PM usage count is equal to zero at that time.
The actions carried out during hibernation and resume from it are
analogous to the ones described above.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
There is some code in drivers/base/power/domain.c that will be useful
for both runtime PM and system-wide power transitions, so make it
depend on CONFIG_PM instead of CONFIG_PM_RUNTIME.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Introduce generic "noirq" power management callback routines for
subsystems in addition to the "regular" generic PM callback routines.
The new routines will be used, among other things, for implementing
system-wide PM transitions support for generic PM domains.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Introduce common headers, helper functions and callbacks allowing
platforms to use simple generic power domains for runtime power
management.
Introduce struct generic_pm_domain to be used for representing
power domains that each contain a number of devices and may be
parent domains or subdomains with respect to other power domains.
Among other things, this structure includes callbacks to be
provided by platforms for performing specific tasks related to
power management (i.e. ->stop_device() may disable a device's
clocks, while ->start_device() may enable them, ->power_off() is
supposed to remove power from the entire power domain
and ->power_on() is supposed to restore it).
Introduce functions that can be used as power domain runtime PM
callbacks, pm_genpd_runtime_suspend() and pm_genpd_runtime_resume(),
as well as helper functions for the initialization of a power
domain represented by a struct generic_power_domain object,
adding a device to or removing a device from it and adding or
removing subdomains.
Introduce configuration option CONFIG_PM_GENERIC_DOMAINS to be
selected by the platforms that want to use the new code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Reviewed-by: Kevin Hilman <khilman@ti.com>
The naming convention used by commit 7538e3db6e015e890825fbd9f86599b
(PM: Add support for device power domains), which introduced the
struct dev_power_domain type for representing device power domains,
evidently confuses some developers who tend to think that objects
of this type must correspond to "power domains" as defined by
hardware, which is not the case. Namely, at the kernel level, a
struct dev_power_domain object can represent arbitrary set of devices
that are mutually dependent power management-wise and need not belong
to one hardware power domain. To avoid that confusion, rename struct
dev_power_domain to struct dev_pm_domain and rename the related
pointers in struct device and struct pm_clk_notifier_block from
pwr_domain to pm_domain.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Kevin Hilman <khilman@ti.com>
The kernel configuration UEVENT_HELPER_PATH is a string to
the uevent helper program. Add more description about how
to disable this feature and how to enable it again during
runtime.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The help message for the configuration variable was inconsistent
with the way "make firmware_install" really works.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix some grammatical errors and reword a few sentences.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'driver-core-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
Connector: Correctly set the error code in case of success when dispatching receive callbacks
Connector: Set the CN_NETLINK_USERS correctly
pti: PTI semantics fix in pti_tty_cleanup.
pti: ENXIO error case memory leak PTI fix.
pti: double-free security PTI fix
drivers:misc: ti-st: fix skipping of change remote baud
drivers/base/platform.c: don't mark platform_device_register_resndata() as __init_or_module
st_kim: Handle case of no device found for ID 0
firmware: fix GOOGLE_SMI kconfig dependency warning
Commit 85eb8c8d0b (PM / Runtime:
Generic clock manipulation rountines for runtime PM (v6)) converted
the shmobile platform to using generic code for runtime PM clock
management, but it changed the behavior for CONFIG_PM_RUNTIME unset
incorrectly.
Specifically, for CONFIG_PM_RUNTIME unset pm_runtime_clk_notify()
should enable clocks for action equal to BUS_NOTIFY_BIND_DRIVER and
it should disable them for action equal to BUS_NOTIFY_UNBOUND_DRIVER
(instead of BUS_NOTIFY_ADD_DEVICE and BUS_NOTIFY_DEL_DEVICE,
respectively). Make this function behave as appropriate.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The PM core doesn't handle suspend failures correctly when it comes to
asynchronously suspended devices. These devices are moved onto the
dpm_suspended_list as soon as the corresponding async thread is
started up, and they remain on the list even if they fail to suspend
or the sleep transition is cancelled before they get suspended. As a
result, when the PM core unwinds the transition, it tries to resume
the devices even though they were never suspended.
This patch (as1474) fixes the problem by adding a new "is_suspended"
flag to dev_pm_info. Devices are resumed only if the flag is set.
[rjw:
* Moved the dev->power.is_suspended check into device_resume(),
because we need to complete dev->power.completion and clear
dev->power.is_prepared too for devices whose
dev->power.is_suspended flags are unset.
* Fixed __device_suspend() to avoid setting dev->power.is_suspended
if async_error is different from zero.]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org
This patch (as1473) renames the "in_suspend" field in struct
dev_pm_info to "is_prepared", in preparation for an upcoming change.
The new name is more descriptive of what the field really means.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org
Create a dedicated folder for iommu drivers, and move the base
iommu implementation over there.
Grouping the various iommu drivers in a single location will help
finding similar problems shared by different platforms, so they
could be solved once, in the iommu framework, instead of solved
differently (or duplicated) in each driver.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The loops over connection ID strings in pm_runtime_clk_notify()
should actually iterate over the strings and not over the elements
of the first of them, so make them behave as appropriate.
This fixes a regression introduced by commit 600b776eb3
(OMAP1 / PM: Use generic clock manipulation routines for runtime PM).
Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This reverts 737a3bb941 ("Driver core: move platform device
creation helpers to .init.text (if MODULE=n)"). That patch assumed that
platform_device_register_resndata() is only ever called from __init code
but that isn't true in the case ioctl->drm_ioctl->radeon_cp_init().
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=35192
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: Anthony Basile <blueness@gentoo.org>
Cc: Greg KH <gregkh@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (44 commits)
debugfs: Silence DEBUG_STRICT_USER_COPY_CHECKS=y warning
sysfs: remove "last sysfs file:" line from the oops messages
drivers/base/memory.c: fix warning due to "memory hotplug: Speed up add/remove when blocks are larger than PAGES_PER_SECTION"
memory hotplug: Speed up add/remove when blocks are larger than PAGES_PER_SECTION
SYSFS: Fix erroneous comments for sysfs_update_group().
driver core: remove the driver-model structures from the documentation
driver core: Add the device driver-model structures to kerneldoc
Translated Documentation/email-clients.txt
RAW driver: Remove call to kobject_put().
reboot: disable usermodehelper to prevent fs access
efivars: prevent oops on unload when efi is not enabled
Allow setting of number of raw devices as a module parameter
Introduce CONFIG_GOOGLE_FIRMWARE
driver: Google Memory Console
driver: Google EFI SMI
x86: Better comments for get_bios_ebda()
x86: get_bios_ebda_length()
misc: fix ti-st build issues
params.c: Use new strtobool function to process boolean inputs
debugfs: move to new strtobool
...
Fix up trivial conflicts in fs/debugfs/file.c due to the same patch
being applied twice, and an unrelated cleanup nearby.
Introduce generic .prepare() and .complete() power management
callbacks, currently missing, that can be used by subsystems and
power domains and export them. Provide NULL definitions of all
the generic system sleep callbacks for CONFIG_PM_SLEEP unset.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If device drivers allocate substantial amounts of memory (above 1 MB)
in their hibernate .freeze() callbacks (or in their legacy suspend
callbcks during hibernation), the subsequent creation of hibernate
image may fail due to the lack of memory. This is the case, because
the drivers' .freeze() callbacks are executed after the hibernate
memory preallocation has been carried out and the preallocated amount
of memory may be too small to cover the new driver allocations.
Unfortunately, the drivers' .prepare() callbacks also are executed
after the hibernate memory preallocation has completed, so they are
not suitable for allocating additional memory either. Thus the only
way a driver can safely allocate memory during hibernation is to use
a hibernate/suspend notifier. However, the notifiers are called
before the freezing of user space and the drivers wanting to use them
for allocating additional memory may not know how much memory needs
to be allocated at that point.
To let device drivers overcome this difficulty rework the hibernation
sequence so that the memory preallocation is carried out after the
drivers' .prepare() callbacks have been executed, so that the
.prepare() callbacks can be used for allocating additional memory
to be used by the drivers' .freeze() callbacks. Update documentation
to match the new behavior of the code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Now that we have CONFIG_DYNAMIC_DEBUG there is no need for yet
another flag causing dev_dbg() and pr_debug() statements in the
core PM code to produce output. Moreover, CONFIG_PM_VERBOSE
causes so much output to be generated that it's not really useful
and almost no one sets it.
References: https://bugzilla.kernel.org/show_bug.cgi?id=23182
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* power-domains:
PM: Fix build issue in clock_ops.c for CONFIG_PM_RUNTIME unset
PM: Revert "driver core: platform_bus: allow runtime override of dev_pm_ops"
OMAP1 / PM: Use generic clock manipulation routines for runtime PM
PM / Runtime: Generic clock manipulation rountines for runtime PM (v6)
PM / Runtime: Add subsystem data field to struct dev_pm_info
OMAP2+ / PM: move runtime PM implementation to use device power domains
PM / Platform: Use generic runtime PM callbacks directly
shmobile: Use power domains for platform runtime PM
PM: Export platform bus type's default PM callbacks
PM: Make power domain callbacks take precedence over subsystem ones
* syscore:
PM: Remove sysdev suspend, resume and shutdown operations
PM / PowerPC: Use struct syscore_ops instead of sysdevs for PM
PM / UNICORE32: Use struct syscore_ops instead of sysdevs for PM
PM / AVR32: Use struct syscore_ops instead of sysdevs for PM
PM / Blackfin: Use struct syscore_ops instead of sysdevs for PM
ARM / Samsung: Use struct syscore_ops for "core" power management
ARM / PXA: Use struct syscore_ops for "core" power management
ARM / SA1100: Use struct syscore_ops for "core" power management
ARM / Integrator: Use struct syscore_ops for core PM
ARM / OMAP: Use struct syscore_ops for "core" power management
ARM: Use struct syscore_ops instead of sysdevs for PM in common code
wakeup_source_add() adds an item into wakeup_sources list.
There is no need to call synchronize_rcu() at this point.
Its only needed in wakeup_source_remove()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The "wakeup" device sysfs file is only created if CONFIG_PM_SLEEP
is set, so put it under CONFIG_PM_SLEEP and make a build warning
related to it go away.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Some drivers erroneously use request_firmware() from their ->resume()
(or ->thaw(), or ->restore()) callbacks, which is not going to work
unless the firmware has been built in. This causes system resume to
stall until the firmware-loading timeout expires, which makes users
think that the resume has failed and reboot their machines
unnecessarily. For this reason, make _request_firmware() print a
warning and return immediately with error code if it has been called
when tasks are frozen and it's impossible to start any new usermode
helpers.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Reviewed-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
The driver core tries to prevent race conditions between runtime PM
and driver removal from happening by incrementing the runtime PM
usage counter of the device and executing pm_runtime_barrier() before
running the bus notifier and the ->remove() callbacks provided by the
device's subsystem or driver. This guarantees that, if a future
runtime suspend of the device has been scheduled or a runtime resume
or idle request has been queued up right before the driver removal,
it will be canceled or waited for to complete and no other
asynchronous runtime suspend or idle requests for the device will be
put into the PM workqueue until the ->remove() callback returns.
However, it doesn't prevent resume requests from being queued up
after pm_runtime_barrier() has been called and it doesn't prevent
pm_runtime_resume() from executing the device subsystem's runtime
resume callback. Morever, it prevents the device's subsystem or
driver from putting the device into the suspended state by calling
pm_runtime_suspend() from its ->remove() routine. This turns out to
be a major inconvenience for some subsystems and drivers that want to
leave the devices they handle in the suspended state.
To really prevent runtime PM callbacks from racing with the bus
notifier callback in __device_release_driver(), which is necessary,
because the notifier is used by some subsystems to carry out
operations affecting the runtime PM functionality, use
pm_runtime_get_sync() instead of the combination of
pm_runtime_get_noresume() and pm_runtime_barrier(). This will resume
the device if it's in the suspended state and will prevent it from
being suspended again until pm_runtime_put_*() is called.
To allow subsystems and drivers to put devices into the suspended
state by calling pm_runtime_suspend() from their ->remove() routines,
execute pm_runtime_put_sync() after running the bus notifier in
__device_release_driver(). This will require subsystems and drivers
to make their ->remove() callbacks avoid races with runtime PM
directly, but it will allow of more flexibility in the handling of
devices during the removal of their drivers.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The platform_bus_set_pm_ops() operation is deprecated in favor of the
new device power domain infrastructre implemented in commit
7538e3db6e (PM: add support for device
power domains)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
drivers/base/memory.c: In function 'memory_block_change_state':
drivers/base/memory.c:281: warning: unused variable 'i'
less beer, more testing
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On ppc64 the minimum memory section for hotplug is 16MB but most
recent machines have a memory block size of 256MB. This means
memory_block_change_state does 16 separate calls to
memory_section_action.
This also means we call the notifiers 16 times and the hook
in the ehea network driver is quite costly. To offline one 256MB
region takes:
# time echo offline > /sys/devices/system/memory/memory32/state
7.9s
This patch removes the loop and calls online_pages or
remove_memory once for the entire region and in doing so makes
the logic simpler since we don't have to back out if things fail
part way through.
The same test to offline one region now takes:
# time echo online > /sys/devices/system/memory/memory32/state
0.67s
Over 11 times faster.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since suspend, resume and shutdown operations in struct sysdev_class
and struct sysdev_driver are not used any more, remove them. Also
drop sysdev_suspend(), sysdev_resume() and sysdev_shutdown() used
for executing those operations and modify all of their users
accordingly. This reduces kernel code size quite a bit and reduces
its complexity.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Many different platforms and subsystems may want to disable device
clocks during suspend and enable them during resume which is going to
be done in a very similar way in all those cases. For this reason,
provide generic routines for the manipulation of device clocks during
suspend and resume.
Convert the ARM shmobile platform to using the new routines.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Once shmobile platforms have been converted to using power domains
for overriding the platform bus type's PM callbacks, it isn't
necessary to use the __weakly defined wrappers around the generinc
runtime PM callbacks in the platform bus type any more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Export the default PM callbacks defined for the platform bus type so
that they can be used by power domains for suspending and resuming
platform devices in the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Change the PM core's behavior related to power domains in such a way
that, if a power domain is defined for a given device, its callbacks
will be executed instead of and not in addition to the device
subsystem's PM callbacks.
The idea behind the initial implementation of power domains handling
by the PM core was that power domain callbacks would be executed in
addition to subsystem callbacks, so that it would be possible to
extend the subsystem callbacks by using power domains. It turns out,
however, that this wouldn't be really convenient in some important
situations.
For example, there are systems in which power can only be removed
from entire power domains. On those systems it is not desirable to
execute device drivers' PM callbacks until it is known that power is
going to be removed from the devices in question, which means that
they should be executed by power domain callbacks rather then by
subsystem (e.g. bus type) PM callbacks, because subsystems generally
have no information about what devices belong to which power domain.
Thus, for instance, if the bus type in question is the platform bus
type, its PM callbacks generally should not be called in addition to
power domain callbacks, because they run device drivers' callbacks
unconditionally if defined.
While in principle the default subsystem PM callbacks, or a subset of
them, may be replaced with different functions, it doesn't seem
correct to do so, because that would change the subsystem's behavior
with respect to all devices in the system, regardless of whether or
not they belong to any power domains. Thus, the only remaining
option is to make power domain callbacks take precedence over
subsystem callbacks.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Kevin Hilman <khilman@ti.com>
It turns out that some PCI devices are only found to be
wakeup-capable during registration, in which case, when
device_set_wakeup_capable() is called, device_is_registered() already
returns 'true' for the given device, but dpm_sysfs_add() hasn't been
called for it yet. This leads to situations in which the device's
power.can_wakeup flag is not set as requested because of failing
wakeup_sysfs_add() and its wakeup-related sysfs files are not
created, although they should be present. This is a post-2.6.38
regression introduced by commit cb8f51bdad
(PM: Do not create wakeup sysfs files for devices that cannot wake
up).
To work around this problem initialize the device's power.entry
field to an empty list head and make device_set_wakeup_capable()
check if it is still empty before attempting to add the devices
wakeup-related sysfs files with wakeup_sysfs_add(). Namely, if
power.entry is still empty at this point, device_pm_add() hasn't been
called yet for the device and its wakeup-related files will be
created later, so device_set_wakeup_capable() doesn't have to create
them.
Reported-and-tested-by: Tino Keitel <tino.keitel@tikei.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the line longer than 80 of memory_uevent function .
Signed-off-by: Wanlong Gao <wanlong.gao@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Before commit
b402843 (Driver core: move dev_get/set_drvdata to drivers/base/dd.c)
calling dev_set_drvdata with dev=NULL was an unchecked error. After some
discussion about what to return in this case removing the check (and so
producing a null pointer exception) seems fine.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes the res = NULL case more consistant to the res != NULL case
as now both overwrite pdev->resource.
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes the data = NULL case more consistent to the data != NULL case.
The functional change is that now
platform_device_add_data(somepdev, NULL, somesize)
sets pdev->dev.platform_data to NULL instead of not touching it.
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a device is registered to a bus it will be a) added to the list
of devices of the bus and b) bind to a driver (if one matches). As a
result of a driver being registered at this bus between a) and b) this
device could already be bound to a driver. This leads to a warning
and incorrect refcounting.
To fix this add a check to device_attach to identify an already bound
device.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The device_type structure does not contain data that changes
during usage and should be const. This allows devices to declare
the struct const.
I have patches to change all the subsystems, but need the infra
structure change first.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Device suspend/resume infrastructure is used not only by the suspend
and hibernate code in kernel/power, but also by APM, Xen and the
kexec jump feature. However, commit 40dc166cb5
(PM / Core: Introduce struct syscore_ops for core subsystems PM)
failed to add syscore_suspend() and syscore_resume() calls to that
code, which generally leads to breakage when the features in question
are used.
To fix this problem, add the missing syscore_suspend() and
syscore_resume() calls to arch/x86/kernel/apm_32.c, kernel/kexec.c
and drivers/xen/manage.c.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
In order for MFD drivers to fetch their cell pointer but also their
platform data one, an mfd cell pointer is added to the platform_device
structure.
That allows all MFD sub devices drivers to be MFD agnostic, unless
they really need to access their MFD cell data. Most of them don't,
especially the ones for IPs used by both MFD and non MFD SoCs.
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg KH <gregkh@suse.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Xen save/restore is going to use hibernate device callbacks for
quiescing devices and putting them back to normal operations and it
would need to select CONFIG_HIBERNATION for this purpose. However,
that also would cause the hibernate interfaces for user space to be
enabled, which might confuse user space, because the Xen kernels
don't support hibernation. Moreover, it would be wasteful, as it
would make the Xen kernels include a substantial amount of code that
they would never use.
To address this issue introduce new power management Kconfig option
CONFIG_HIBERNATE_CALLBACKS, such that it will only select the code
that is necessary for the hibernate device callbacks to work and make
CONFIG_HIBERNATION select it. Then, Xen save/restore will be able to
select CONFIG_HIBERNATE_CALLBACKS without dragging the entire
hibernate code along with it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Shriram Rajagopalan <rshriram@cs.ubc.ca>
Introduce Kconfig option allowing architectures where sysdev
operations used during system suspend, resume and shutdown have been
completely replaced with struct sycore_ops operations to avoid
building sysdev code that will never be used.
Make callbacks in struct sys_device and struct sysdev_driver depend
on ARCH_NO_SYSDEV_OPS to allows us to verify if all of the references
have been actually removed from the code the given architecture
depends on.
Make x86 select ARCH_NO_SYSDEV_OPS.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Some subsystems need to carry out suspend/resume and shutdown
operations with one CPU on-line and interrupts disabled. The only
way to register such operations is to define a sysdev class and
a sysdev specifically for this purpose which is cumbersome and
inefficient. Moreover, the arguments taken by sysdev suspend,
resume and shutdown callbacks are practically never necessary.
For this reason, introduce a simpler interface allowing subsystems
to register operations to be executed very late during system suspend
and shutdown and very early during resume in the form of
strcut syscore_ops objects.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
opp_find_freq_exact() documentation has is_available instead
of available. This also fixes warning with the kernel-doc:
scripts/kernel-doc drivers/base/power/opp.c >/dev/null
Warning(drivers/base/power/opp.c:246): No description found for parameter 'available'
Warning(drivers/base/power/opp.c:246): Excess function parameter 'is_available' description in 'opp_find_freq_exact'
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The code handling system-wide power transitions (eg. suspend-to-RAM)
can in theory execute callbacks provided by the device's bus type,
device type and class in each phase of the power transition. In
turn, the runtime PM core code only calls one of those callbacks at
a time, preferring bus type callbacks to device type or class
callbacks and device type callbacks to class callbacks.
It seems reasonable to make them both behave in the same way in that
respect. Moreover, even though a device may belong to two subsystems
(eg. bus type and device class) simultaneously, in practice power
management callbacks for system-wide power transitions are always
provided by only one of them (ie. if the bus type callbacks are
defined, the device class ones are not and vice versa). Thus it is
possible to modify the code handling system-wide power transitions
so that it follows the core runtime PM code (ie. treats the
subsystem callbacks as mutually exclusive).
On the other hand, the core runtime PM code will choose to execute,
for example, a runtime suspend callback provided by the device type
even if the bus type's struct dev_pm_ops object exists, but the
runtime_suspend pointer in it happens to be NULL. This is confusing,
because it may lead to the execution of callbacks from different
subsystems during different operations (eg. the bus type suspend
callback may be executed during runtime suspend of the device, while
the device type callback will be executed during system suspend).
Make all of the power management code treat subsystem callbacks in
a consistent way, such that:
(1) If the device's type is defined (eg. dev->type is not NULL)
and its pm pointer is not NULL, the callbacks from dev->type->pm
will be used.
(2) If dev->type is NULL or dev->type->pm is NULL, but the device's
class is defined (eg. dev->class is not NULL) and its pm pointer
is not NULL, the callbacks from dev->class->pm will be used.
(3) If dev->type is NULL or dev->type->pm is NULL and dev->class is
NULL or dev->class->pm is NULL, the callbacks from dev->bus->pm
will be used provided that both dev->bus and dev->bus->pm are
not NULL.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Kevin Hilman <khilman@ti.com>
Reasoning-sounds-sane-to: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
The platform bus type is often used to handle Systems-on-a-Chip (SoC)
where all devices are represented by objects of type struct
platform_device. In those cases the same "platform" device driver
may be used with multiple different system configurations, but the
actions needed to put the devices it handles into a low-power state
and back into the full-power state may depend on the design of the
given SoC. The driver, however, cannot possibly include all the
information necessary for the power management of its device on all
the systems it is used with. Moreover, the device hierarchy in its
current form also is not suitable for representing this kind of
information.
The patch below attempts to address this problem by introducing
objects of type struct dev_power_domain that can be used for
representing power domains within a SoC. Every struct
dev_power_domain object provides a sets of device power
management callbacks that can be used to perform what's needed for
device power management in addition to the operations carried out by
the device's driver and subsystem.
Namely, if a struct dev_power_domain object is pointed to by the
pwr_domain field in a struct device, the callbacks provided by its
ops member will be executed in addition to the corresponding
callbacks provided by the device's subsystem and driver during all
power transitions.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-and-acked-by: Kevin Hilman <khilman@ti.com>
The dpm_prepare() function increments the runtime PM reference
counters of all devices to prevent pm_runtime_suspend() from
executing subsystem-level callbacks. However, this was supposed to
guard against a specific race condition that cannot happen, because
the power management workqueue is freezable, so pm_runtime_suspend()
can only be called synchronously during system suspend and we can
rely on subsystems and device drivers to avoid doing that
unnecessarily.
Make dpm_prepare() drop the runtime PM reference to each device
after making sure that runtime resume is not pending for it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Kevin Hilman <khilman@ti.com>
After redefining CONFIG_PM to depend on (CONFIG_PM_SLEEP ||
CONFIG_PM_RUNTIME) the CONFIG_PM_OPS option is redundant and can be
replaced with CONFIG_PM.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Currently, wakeup sysfs attributes are created for all devices,
regardless of whether or not they are wakeup-capable. This is
excessive and complicates wakeup device identification from user
space (i.e. to identify wakeup-capable devices user space has to read
/sys/devices/.../power/wakeup for all devices and see if they are not
empty).
Fix this issue by avoiding to create wakeup sysfs files for devices
that cannot wake up the system from sleep states (i.e. whose
power.can_wakeup flags are unset during registration) and modify
device_set_wakeup_capable() so that it adds (or removes) the relevant
sysfs attributes if a device's wakeup capability status is changed.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
printk()s without a priority level default to KERN_WARNING. To reduce
noise at KERN_WARNING, this patch sets the priority level appriopriately
for unleveled printks()s. This should be useful to folks that look at
dmesg warnings closely.
Changed these messages to pr_info().
Signed-off-by: Mandeep Singh Baines <msb@chromium.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Since pm_save_wakeup_count() has just been changed to clear
events_check_enabled unconditionally before checking if there are
any new wakeup events registered since the last read from
/sys/power/wakeup_count, the detection of wakeup events during
suspend may be disabled, after it's been enabled, by writing a
"wrong" value back to /sys/power/wakeup_count. For this reason,
it is not necessary to update events_check_enabled in
pm_get_wakeup_count() any more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
According to Documentation/ABI/testing/sysfs-power, the
/sys/power/wakeup_count interface should only make the kernel react
to wakeup events during suspend if the last write to it has been
successful. However, if /sys/power/wakeup_count is written to two
times in a row, where the first write is successful and the second
is not, the kernel will still react to wakeup events during suspend
due to a bug in pm_save_wakeup_count().
Fix the bug by making pm_save_wakeup_count() clear
events_check_enabled unconditionally before checking if there are
any new wakeup events registered since the previous read from
/sys/power/wakeup_count.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The memory barrier in wakeup_source_deactivate() is supposed to
prevent the callers of pm_wakeup_pending() and pm_get_wakeup_count()
from seeing the new value of events_in_progress (0, in particular)
and the old value of event_count at the same time. However, if
wakeup_source_deactivate() is executed by CPU0 and, for instance,
pm_wakeup_pending() is executed by CPU1, where both processors can
reorder operations, the memory barrier in wakeup_source_deactivate()
doesn't affect CPU1 which can reorder reads. In that case CPU1 may
very well decide to fetch event_count before it's modified and
events_in_progress after it's been updated, so pm_wakeup_pending()
may fail to detect a wakeup event. This issue can be addressed by
using a single atomic variable to store both events_in_progress
and event_count, so that they can be updated together in a single
atomic operation.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The original macro worked only when applied to variables named 'dev'.
While this could have been fixed by simply renaming the macro argument,
a more type-safe replacement by an inline function is preferred.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As a follow-on to the recent patches I submitted that allowed for a sysfs
memory block to span multiple memory sections, we should also update the
probe routine to online all of the memory sections in a memory block. Without
this patch the current code will only add a single memory section. I think
the probe routine should add all of the memory sections in the specified memory
block so that its behavior is in line with memory hotplug actions through
the sysfs interfaces.
This patch applies on top of the previous sysfs memory updates to allow
a sysfs directory o span multiple memory sections.
https://lkml.org/lkml/2011/1/20/245
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the 'phys_index' property of a the memory_block struct to be
called start_section_nr, and add a end_section_nr property. The
data tracked here is the same but the updated naming is more in line
with what is stored here, namely the first and last section number
that the memory block spans.
The names presented to userspace remain the same, phys_index for
start_section_nr and end_phys_index for end_section_nr, to avoid breaking
anything in userspace.
This also updates the node sysfs code to be aware of the new capability for
a memory block to contain multiple memory sections and be aware of the memory
block structure name changes (start_section_nr). This requires an additional
parameter to unregister_mem_sect_under_nodes so that we know which memory
section of the memory block to unregister.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Reviewed-by: Robin Holt <holt@sgi.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the memory sysfs code such that each sysfs memory directory is now
considered a memory block that can span multiple memory sections per
memory block. The default size of each memory block is SECTION_SIZE_BITS
to maintain the current behavior of having a single memory section per
memory block (i.e. one sysfs directory per memory section).
For architectures that want to have memory blocks span multiple
memory sections they need only define their own memory_block_size_bytes()
routine.
Update the memory hotplug documentation to reflect the new behaviors of
memory blocks reflected in sysfs.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Reviewed-by: Robin Holt <holt@sgi.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When encountering an error while executing the driver's ->add method, we
should cancel registration and unwind what we've regged so far. The low
level ->add methods do return proper error codes but those aren't looked
at in sysdev_driver_register(). Fix that by sharing the unregistering
code.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use gcc's __func__ instead of the function name.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some place in firmware_class.c using "int uevent" define, but others use "bool
uevent".
This patch replace all int uevent define to bool.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add text, courtesy of Kay Sievers, that provides some background on
device_rename() and why it shouldn't be used.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1445) fixes a bug in the runtime PM core left over from
the addition of the no_callbacks flag. If this flag is set then it is
possible for rpm_suspend() to be called in_interrupt, so when
releasing spinlocks it's important not to re-enable interrupts.
To avoid an unnecessary save-and-restore of the interrupt flag, the
patch also inlines a pm_request_idle() call.
This fixes Bugzilla #27482.
(The offending code was added in 2.6.37, so it's not necessary to apply
this to any earlier stable kernels.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: tim blechmann <tim@klingt.org>
CC: <stable@kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
driver core: Document that device_rename() is only for networking
sysfs: remove useless test from sysfs_merge_group
driver-core: merge private parts of class and bus
driver core: fix whitespace in class_attr_string
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (34 commits)
HID: roccat: Update sysfs attribute doc
HID: roccat: don't use #pragma pack
HID: roccat: Add support for Roccat Kone[+] v2
HID: roccat: reduce number of functions in kone and pyra drivers
HID: roccat: declare meaning of pack pragma usage in driver headers
HID: roccat: use class for char device for sysfs attribute creation
sysfs: Introducing binary attributes for struct class
HID: hidraw: add compatibility ioctl() for 32-bit applications.
HID: hid-picolcd: Fix memory leak in picolcd_debug_out_report()
HID: picolcd: fix misuse of logical operation in place of bitop
HID: usbhid: base runtime PM on modern API
HID: replace offsets values with their corresponding BTN_* defines
HID: hid-mosart: support suspend/resume
HID: hid-mosart: ignore buttons report
HID: hid-picolcd: don't use flush_scheduled_work()
HID: simplify an index check in hid_lookup_collection
HID: Hoist assigns from ifs
HID: Remove superfluous __inline__
HID: Use vzalloc for vmalloc/memset(,0...)
HID: Add and use hid_<level>: dev_<level> equivalents
...
Added dev_bin_attrs to struct class similar to existing dev_attrs.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The __pm_generic_resume() function changes the given device's runtime
PM status to RPM_ACTIVE if its driver's callback returns 0, but it
only should do that if the rumtime PM is enabled for the device.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The registration of a new parentless device during system suspend
will not lead to any complications affecting the PM core (the device
will be effectively seen after the subsequent resume has completed),
so remove the code used for detection of such events.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The device power.status field is too complicated for its purpose
(storing the information about whether or not the device is in the
"active" state from the PM core's point of view), so replace it with
a bit field and modify all of its users accordingly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Since a separate list of devices is used to link devices that have
completed each stage of suspend (or resume), it is not necessary to
check dev->power.status in the core device resume routines any more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Instead of keeping all devices in the same list during system suspend
and resume, regardless of what suspend-resume callbacks have been
executed for them already, use separate lists of devices that have
had their ->prepare(), ->suspend() and ->suspend_noirq() callbacks
executed. This will allow us to simplify the core device suspend and
resume routines.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The compiler complains that calltime may be uninitialized in
pm_noirq_op(), so add extra initialization for that variable to
avoid the warning.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Before starting to suspend a device in __device_suspend() check if
there's a request to abort the power transition and return -EBUSY
in that case.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
To avoid confusion with the meaning and return value of
pm_check_wakeup_events() replace it with pm_wakeup_pending() that
will work the other way around (ie. return true when system-wide
power transition should be aborted).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Currently dpm_prepare() returns error code if it finds that a device
being suspended has a pending runtime resume request. However, it
should not do that if the checking for wakeup events is not enabled.
On the other hand, if the checking for wakeup events is enabled, it
can return error when a wakeup event is detected, regardless of its
source.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch (as1431c) makes the synchronous runtime-PM interface
suitable for use in interrupt handlers. Subsystems can call the new
pm_runtime_irq_safe() function to tell the PM core that a device's
runtime_suspend and runtime_resume callbacks should be invoked with
interrupts disabled and the spinlock held. This permits the
pm_runtime_get_sync() and the new pm_runtime_put_sync_suspend()
routines to be called from within interrupt handlers.
When a device is declared irq-safe in this way, the PM core increments
the parent's usage count, so the parent will never be runtime
suspended. This prevents difficult situations in which an irq-safe
device can't resume because it is forced to wait for its non-irq-safe
parent.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Commit 05aa55dddb changed routines to
succeed if the driver handler is not defined. Comments were not updated.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>