* In btrfs_delete_inode, wait for ordered extents after calling
truncate_inode_pages. This is much faster, and more correct
* Properly clear our the PageChecked bit everywhere we redirty the page.
* Change the writepage fixup handler to lock the page range and check to
see if an ordered extent had been inserted since the improperly dirtied
page was discovered
* Wait for ordered extents outside the transaction. This isn't required
for locking rules but does improve transaction latencies
* Reduce contention on the alloc_mutex by dropping it while incrementing
refs on a node/leaf and while dropping refs on a leaf.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Data checksumming is done right before the bio is sent down the IO stack,
which means a single bio might span more than one ordered extent. In
this case, the checksumming data is split between two ordered extents.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Checksum items are not inserted until the entire ordered extent is on disk,
but individual pages might be clean and available for reclaim long before
the whole extent is on disk.
In order to allow those pages to be freed, we need to be able to search
the list of ordered extents to find the checksum that is going to be inserted
in the tree. This way if the page needs to be read back in before
the checksums are in the btree, we'll be able to verify the checksum on
the page.
This commit adds the ability to search the pending ordered extents for
a given offset in the file, and changes btrfs_releasepage to allow
ordered pages to be freed.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This changes the ordered data code to update i_size after the extent
is on disk. An on disk i_size is maintained in the in-memory btrfs inode
structures, and this is updated as extents finish.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The old data=ordered code would force commit to wait until
all the data extents from the transaction were fully on disk. This
introduced large latencies into the commit and stalled new writers
in the transaction for a long time.
The new code changes the way data allocations and extents work:
* When delayed allocation is filled, data extents are reserved, and
the extent bit EXTENT_ORDERED is set on the entire range of the extent.
A struct btrfs_ordered_extent is allocated an inserted into a per-inode
rbtree to track the pending extents.
* As each page is written EXTENT_ORDERED is cleared on the bytes corresponding
to that page.
* When all of the bytes corresponding to a single struct btrfs_ordered_extent
are written, The previously reserved extent is inserted into the FS
btree and into the extent allocation trees. The checksums for the file
data are also updated.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This allows us to delete an unlinked inode with dirty pages from the list
instead of forcing commit to write these out before deleting the inode.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
2.6.18 seems to get caught in an infinite loop when
cancel_rearming_delayed_workqueue is called more than once, so this switches
to cancel_delayed_work, which is arguably more correct.
Also, balance_dirty_pages can run into problems with 2.6.18 based kernels
because it doesn't have the per-bdi dirty limits. This avoids calling
balance_dirty_pages on the btree inode unless there is actually something
to balance, which is a good optimization in general.
Finally there's a compile fix for ordered-data.h
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Using ilookup5 during data=ordered writeback could deadlock on I_LOCK. This
saves a pointer to the inode instead.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This forces file data extents down the disk along with the metadata that
references them. The current implementation is fairly simple, and just
writes out all of the dirty pages in an inode before the commit.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Chris Mason