Commit 5fe5b767dc ("ASoC: dapm: Do not pretend to support controls for non
mixer/mux widgets") revealed ill-defined control in a route between
"STENL Mux" and DACs in max98090.c:
max98090 i2c-193C9890:00: Control not supported for path STENL Mux -> [NULL] -> DACL
max98090 i2c-193C9890:00: ASoC: no dapm match for STENL Mux --> NULL --> DACL
max98090 i2c-193C9890:00: ASoC: Failed to add route STENL Mux -> NULL -> DACL
max98090 i2c-193C9890:00: Control not supported for path STENL Mux -> [NULL] -> DACR
max98090 i2c-193C9890:00: ASoC: no dapm match for STENL Mux --> NULL --> DACR
max98090 i2c-193C9890:00: ASoC: Failed to add route STENL Mux -> NULL -> DACR
Since there is no control between "STENL Mux" and DACs the control name must
be NULL not "NULL".
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Commit e409dfbfcc ("ASoC: dapm: Add a few supply widget sanity checks")
broke digital microphone support in max98090.c:
max98090 i2c-193C9890:00: Conditional paths are not supported for supply widgets (DMICL_ENA -> [DMIC] -> DMIC Mux)
max98090 i2c-193C9890:00: ASoC: no dapm match for DMICL_ENA --> DMIC --> DMIC Mux
max98090 i2c-193C9890:00: ASoC: Failed to add route DMICL_ENA -> DMIC -> DMIC Mux
max98090 i2c-193C9890:00: Conditional paths are not supported for supply widgets (DMICR_ENA -> [DMIC] -> DMIC Mux)
max98090 i2c-193C9890:00: ASoC: no dapm match for DMICR_ENA --> DMIC --> DMIC Mux
max98090 i2c-193C9890:00: ASoC: Failed to add route DMICR_ENA -> DMIC -> DMIC Mux
Problem is partially caused by commit f69e3caa9e ("ASoC: max98090: Enable
both DMIC channels also when using mono configuration") which connects
"DMICL_ENA" and "DMICR_ENA" supply widgets to "DMIC Mux".
Fix the breakage by reverting f69e3caa9e and then by adding additional
"DMICR_ENA" to "DMICL" and "DMICL_ENA" to "DMICR" cross-connections. This
disconnects these supply widgets from the mux and makes sure that both DMIC
data channels are still enabled together.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Baytrail-based chromebooks have a 20MHz mclk, the code was setting
the divisor incorrectly in this case. According to the 98090
datasheet, the divisor should be set to DIV1 for 10 <= mclk <= 20.
Correct this and the surrounding clock ranges as well to match the
datasheet.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to MAX98090 specification "Digital microphone clock (DMC) is
enabled once both data channels are enabled.". Therefore both digital
microphone data channels must be enabled also when using mono microphone
configuration.
Fix this by moving "DMICL_ENA" and "DMICR_ENA" supply widgets from "DMICL"
and "DMICR" inputs to "DMIC Mux" in order to enable both data channels
whenever there is active mono or stereo digital microphone input path.
Use of "DMICL" and "DMICR" inputs are retained for informative source and in
case the driver would find use for exact digital microphone configuration in
the future.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no other use for extmic_mux than setting it to zero so remove it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
struct max98090_priv member irq is now used only locally in
max98090_i2c_probe() and can be removed.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Keep MAX98090 interrupt requested after i2c device probing as long as the
driver is loaded. This fixes the issue where subsequent codec probe
max98090_probe() call fails in interrupt request since interrupt wasn't
freed over codec remove-reprobe cycle.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All MAX98090 input clocks MCLK, LRCLK and BCLK must be running and stable
before powering on the codec in slave mode. Otherwise the PLL may not lock
to LRCLK causing silence in playback and capture. How often that happens is
somewhat hardware and clock configuration specific.
Now if wanting to follow strictly this clocks must be active before
powering the codec on requirement we should have a notification from DAI
driver to codec driver when clocks are activated and take codec out of
shutdown only after that. Plus take care of possible active bypass paths.
However, when PLL unlock occurs, MAX98090 asserts the PLL Unlock Flag which
can be configured as an IRQ source. This allows to workaround around the
issue by toggling the codec power shortly in case of PLL lock failure.
In order to prevent needlessly toggling codec power in case of short PLL
unlocks at the beginning of stream this patch implements delayed activation
for PLL unlock interrupt. Then workaround is run only when the PLL doesn't
lock at all.
Power toggling workaround for PLL unlock comes originally from
Liam Girdwood <liam.r.girdwood@linux.intel.com> and delayed activation from
me.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max98090_{suspend,resume}() functions are used for system sleep and
therefore need to be guarded by CONFIG_PM_SLEEP rather than CONFIG_PM.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
max98090_handle_pdata() is not doing anything other than printing
a message if pdata is not valid. This can be removed.
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
CODEC type (MAX98090/MAX98091) can be specified from device-tree file,
it can also be obtained from the CODEC during runtime.
Add an explicit check to figure out if both are matching, else print
a message warning about the same.
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The MAX98091 CODEC is the same as MAX98090 CODEC, but with an extra
microphone. Existing driver for MAX98090 CODEC already has support
for MAX98091 CODEC. Adding proper compatible string so that MAX98091
CODEC can be specified from device tree.
Signed-off-by: Wonjoon Lee <woojoo.lee@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
max98090.c doesn't free the threaded interrupt it requests. This causes
an oops when doing "cat /proc/interrupts" after snd-soc-max98090.ko is
unloaded.
Fix this by requesting the interrupt by using devm_request_threaded_irq().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Stable <stable@vger.kernel.org> # 3.10+
Signed-off-by: Mark Brown <broonie@linaro.org>
If master clock is provided through device tree, then update
the master clock frequency during set_sysclk.
Documentation has been updated to reflect the change.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds the clock divisor and multiplier NI, MI values for audio
sampling frequencies 44100 and 48000 Hz and PCLK 19.2 MHz. This is useful
for the Odroid X2/U2 boards when the codec works in master mode and its
MCLK clock is fed from the I2S CDCLK output.
Signed-off-by: Chen Zhen <zhen1.chen@samsung.com>
[s.nawrocki@samsung.com: edited the commit description]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Microphone bias level configuration register can configure voltage between
2.2 V and 2.8 V but doesn't manage is voltage on or off. Microphone bias
on/off state is controlled by "MICBIAS" DAPM widget.
Therefore there is no need to update bias voltage conditionally depending on
jack state each time when codec goes to SND_SOC_BIAS_ON state and setting
can be moved to max98090_probe() as driver currently doesn't support other
levels than 2.8 V.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
BCL is being configured in two places producing a warning message.
Make sure we only configure BCLK once and when we are master.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add ACPI ID for MAX98090 and ACPI 5 I2C device probing support.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make sure the cache is fully flushed at resume time.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make sure we reset codec and clear any IRQs on resume. This matches
the init sequence in probe.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Reset needs to wait 20ms before other codec IO is performed. This wait
was not being performed. Fix this by making sure the reset register is not
restored with the cache, but use the manual reset method in resume with
the wait.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
TLV for digital sidetone volume is wrong, this fix matches it to the
datasheet.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SND_SOC_DAPM_VIRT_MUX and SOC_DAPM_ENUM_VIRT are deprecated and merely an alias
for SND_SOC_DAPM_MUX and SOC_DAPM_ENUM. Replace the deprecated macros so we can
eventually remove their definition.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_match_ptr is defined in of.h. Include it explicitly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
For CODEC controls snd_kcontrol_chip() currently returns a pointer to the
CODEC that registered the control. With the upcoming consolidation of
platform and CODEC controls this will change. Prepare for this by introducing
the snd_soc_kcontrol_codec() helper function that will hide the implementation
details of how the CODEC for a control can be obtained. This will allow us to
change this easily in the future.
The patch also updates all CODEC drivers to use the new helper function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a device tree match table. This serves to make the driver's support
of device tree more explicit. Perhaps the fallback for DT matching to
using the i2c_device_id table will go away one day, since it fails in
face of devices from different vendors with the same name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver assigns a value to the control_data field of the driver's state
struct, but never reads it again. Which means it is unused and can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
For some CODEC drivers like who act as the MFDs children are ignored
by this patch.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For the upcoming consolidation for MUXs and virtual MUXs we need to mark virtual
enums as such.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Just replace with the helper macro. No functional change at all.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The REVISION_ID register is not currently marked readable. snd_soc_read()
refuses to read the register, and hence probe() fails.
Fixes: d4807ad2c4 ("regmap: Check readable regs in _regmap_read")
[exposed the bug, by checking for readability]
Fixes: 685e42154d ("ASoC: Replace max98090 Device Driver")
[left out this register from the readable list]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Sync regcache when entering STANDBY from OFF. ON isn't entered with
OFF as the current state, so the registers were not being re-synced
after suspend/resume.
The 98088 and 98095 already call regcache_sync from STANDBY.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
None of the delayed work the driver schedules has particularly short delays
and it is not performance sensitive so let the scheduler run it wherever
is most efficient rather than in a per CPU workqueue by using the system
power efficient workqueue.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Otherwise the functions will be defined but unreferenced when runtime PM
is disabled, generating warnings.
Signed-off-by: Mark Brown <broonie@linaro.org>
request_threaded_irq() rejects calls which both do not specify a handler
(indicating that the primary IRQ handler should be used) and do not set
IRQF_ONESHOT because the combination is unsafe with level-triggered
interrupts. It is safe in this case, though, since max98090 IRQs are
edge-triggered and the interrupts aren't ACK'ed until the codec's IRQ
status register is read. Because of this, an IRQF_ONESHOT interrupt
doesn't really make a difference, but request one anyway in order to make
request_threaded_irq() happy.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The max98090 driver currently treats the digital mic enable as a supply
on the record path, causing the digital mic enable to always be turned on
when attempting to record. This is incorrect, however, since the digital
mic enable is also a mux control where 0 selects the ADC output as input
to the record-path DSP and 1 selects the digital mic. This patch adds
a virtual DMIC mux to the reocrd path so that we can switch between the
ADC and the digital mic for recording.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jarkko Nikula