dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217112656.30860-1-peter.ujfalusi@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Here is the "big" set of driver core patches for 5.5-rc1
There's a few minor cleanups and fixes in here, but the majority of the
patches in here fall into two buckets:
- debugfs api cleanups and fixes
- driver core device link support for boot dependancy issues
The debugfs api cleanups are working to slowly refactor the debugfs apis
so that it is even harder to use incorrectly. That work has been
happening for the past few kernel releases and will continue over time,
it's a long-term project/goal
The driver core device link support missed 5.4 by just a bit, so it's
been sitting and baking for many months now. It's from Saravana Kannan
to help resolve the problems that DT-based systems have at boot time
with dependancy graphs and kernel modules. Turns out that no one has
actually tried to build a generic arm64 kernel with loads of modules and
have it "just work" for a variety of platforms (like a distro kernel)
The big problem turned out to be a lack of depandancy information
between different areas of DT entries, and the work here resolves that
problem and now allows devices to boot properly, and quicker than a
monolith kernel.
All of these patches have been in linux-next for a long time with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd6m6Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yntJQCcCqg6RQ7LTdHuZv1ETeefXlsfk00An1Jtean6
42bWGx52bGFvAcpjWy8R
=P7hq
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core patches for 5.5-rc1
There's a few minor cleanups and fixes in here, but the majority of
the patches in here fall into two buckets:
- debugfs api cleanups and fixes
- driver core device link support for boot dependancy issues
The debugfs api cleanups are working to slowly refactor the debugfs
apis so that it is even harder to use incorrectly. That work has been
happening for the past few kernel releases and will continue over
time, it's a long-term project/goal
The driver core device link support missed 5.4 by just a bit, so it's
been sitting and baking for many months now. It's from Saravana Kannan
to help resolve the problems that DT-based systems have at boot time
with dependancy graphs and kernel modules. Turns out that no one has
actually tried to build a generic arm64 kernel with loads of modules
and have it "just work" for a variety of platforms (like a distro
kernel). The big problem turned out to be a lack of dependency
information between different areas of DT entries, and the work here
resolves that problem and now allows devices to boot properly, and
quicker than a monolith kernel.
All of these patches have been in linux-next for a long time with no
reported issues"
* tag 'driver-core-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (68 commits)
tracing: Remove unnecessary DEBUG_FS dependency
of: property: Add device link support for interrupt-parent, dmas and -gpio(s)
debugfs: Fix !DEBUG_FS debugfs_create_automount
of: property: Add device link support for "iommu-map"
of: property: Fix the semantics of of_is_ancestor_of()
i2c: of: Populate fwnode in of_i2c_get_board_info()
drivers: base: Fix Kconfig indentation
firmware_loader: Fix labels with comma for builtin firmware
driver core: Allow device link operations inside sync_state()
driver core: platform: Declare ret variable only once
cpu-topology: declare parse_acpi_topology in <linux/arch_topology.h>
crypto: hisilicon: no need to check return value of debugfs_create functions
driver core: platform: use the correct callback type for bus_find_device
firmware_class: make firmware caching configurable
driver core: Clarify documentation for fwnode_operations.add_links()
mailbox: tegra: Fix superfluous IRQ error message
net: caif: Fix debugfs on 64-bit platforms
mac80211: Use debugfs_create_xul() helper
media: c8sectpfe: no need to check return value of debugfs_create functions
of: property: Add device link support for iommus, mboxes and io-channels
...
There are a couple of statements that are indented by an extra
space, clean this up by remove the extraneous spaces.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
"dw_mci.state" is an enum, which is compatible with u32, so there is no
need to cast its address, preventing further compiler checks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20191025094130.26033-8-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"dw_mci.pending_events" and "dw_mci.completed_events" are "unsigned
long", i.e. 32-bit or 64-bit, depending on the platform. Hence casting
their addresses to "u32 *", and calling debugfs_create_x32() breaks
operation on 64-bit platforms.
Fix this by using the new debugfs_create_xul() helper instead.
Fixes: f95f3850f7 ("mmc: dw_mmc: Add Synopsys DesignWare mmc host driver.")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20191025094130.26033-7-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In cases when SDIO IRQs have been enabled, runtime suspend is prevented by
the driver. However, this still means dw_mci_runtime_suspend|resume() gets
called during system suspend/resume, via pm_runtime_force_suspend|resume().
This means during system suspend/resume, the register context of the dw_mmc
device most likely loses its register context, even in cases when SDIO IRQs
have been enabled.
To re-enable the SDIO IRQs during system resume, the dw_mmc driver
currently relies on the mmc core to re-enable the SDIO IRQs when it resumes
the SDIO card, but this isn't the recommended solution. Instead, it's
better to deal with this locally in the dw_mmc driver, so let's do that.
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In commit 46d179525a ("mmc: dw_mmc: Wait for data transfer after
response errors.") we fixed a tuning-induced hang that I saw when
stress testing tuning on certain SD cards. I won't re-hash that whole
commit, but the summary is that as a normal part of tuning you need to
deal with transfer errors and there were cases where these transfer
errors was putting my system into a bad state causing all future
transfers to fail. That commit fixed handling of the transfer errors
for me.
In downstream Chrome OS my fix landed and had the same behavior for
all SD/MMC commands. However, it looks like when the commit landed
upstream we limited it to only SD tuning commands. Presumably this
was to try to get around problems that Alim Akhtar reported on exynos
[1].
Unfortunately while stress testing reboots (and suspend/resume) on
some rk3288-based Chromebooks I found the same problem on the eMMC on
some of my Chromebooks (the ones with Hynix eMMC). Since the eMMC
tuning command is different (MMC_SEND_TUNING_BLOCK_HS200
vs. MMC_SEND_TUNING_BLOCK) we were basically getting back into the
same situation.
I'm hoping that whatever problems exynos was having in the past are
somehow magically fixed now and we can make the behavior the same for
all commands.
[1] https://lkml.kernel.org/r/CAGOxZ53WfNbaMe0_AM0qBqU47kAfgmPBVZC8K8Y-_J3mDMqW4A@mail.gmail.com
Fixes: 46d179525a ("mmc: dw_mmc: Wait for data transfer after response errors.")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Alim Akhtar <alim.akhtar@gmail.com>
Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Card write threshold control is supposed to be set since controller
version 2.80a for data write in HS400 mode and data read in
HS200/HS400/SDR104 mode. However the current code returns without
configuring it in the case of data writing in HS400 mode.
Meanwhile the patch fixes that the current code goes to
'disable' when doing data reading in HS400 mode.
Fixes: 7e4bf1bc95 ("mmc: dw_mmc: add the card write threshold for HS400 mode")
Signed-off-by: Qing Xia <xiaqing17@hisilicon.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It was found that in IDMAC mode after soft-reset driver switches
to PIO mode.
That's what happens in case of DTO timeout overflow calculation failure:
1. soft-reset is called
2. driver restarts dma
3. descriptors states are checked, one of descriptor is owned by the IDMAC.
4. driver can't use DMA and then switches to PIO mode.
Failure was already fixed in:
https://www.spinics.net/lists/linux-mmc/msg48125.html.
Behaviour while soft-reset is not something we except or
even want to happen. So we switch from dw_mci_idmac_reset
to dw_mci_idmac_init, so descriptors are cleaned before starting dma.
And while at it explicitly zero des0 which otherwise might
contain garbage as being allocated by dmam_alloc_coherent().
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: linux-snps-arc@lists.infradead.org
Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'num-slots' property had already deprecated.
Remove the 'nom-slots' property that is kept to maintain the compatibility.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'clock-freq-min-max' property had already deprecated.
Remove the 'clock-freq-min-max' property that is kept to maintain
the compatibility.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clang reports a compile warning:
drivers/mmc/host/dw_mmc.c:2124:5: warning: Value stored to 'prev_state'
is never read
By checking the code, prev_state and state assignment for
STATE_SENDING_CMD is indeed never used after jumping to unlock tag.
So remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the newly added macro to simply to the code.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 9d9491a7da ("mmc: dw_mmc: Fix the DTO timeout calculation")
and commit 4c2357f57d ("mmc: dw_mmc: Fix the CTO timeout calculation")
made changes, which cause multiply overflow for 32-bit systems. The broken
timeout calculations leads to unexpected ETIMEDOUT errors and causes
stacktrace splat (such as below) during normal data exchange with SD-card.
| Running : 4M-check-reassembly-tcp-cmykw2-rotatew2.out -v0 -w1
| - Info: Finished target initialization.
| mmcblk0: error -110 transferring data, sector 320544, nr 2048, cmd
| response 0x900, card status 0x0
DIV_ROUND_UP_ULL helps to escape usage of __udivdi3() from libgcc and so
code gets compiled on all 32-bit platforms as opposed to usage of
DIV_ROUND_UP when we may only compile stuff on a very few arches.
Lets cast this multiply to u64 type to prevent the overflow.
Fixes: 9d9491a7da ("mmc: dw_mmc: Fix the DTO timeout calculation")
Fixes: 4c2357f57d ("mmc: dw_mmc: Fix the CTO timeout calculation")
Tested-by: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Reported-by: Vineet Gupta <Vineet.Gupta1@synopsys.com> # ARC STAR 9001306872 HSDK, sdio: board crashes when copying big files
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: <stable@vger.kernel.org> # 4.14
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cat /sys/kernel/debug/mmc0/regs will hang up the system since
it's in runtime suspended state, so the genpd and biu_clk is
off. This patch fixes this problem by calling pm_runtime_get_sync
to wake it up before reading the registers.
Fixes: e9ed8835e9 ("mmc: dw_mmc: add runtime PM callback")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add num_caps field for dw_mci_drv_data to validate the controller
id from DT alias and non-DT ways.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 800d78bfcc ("mmc: dw_mmc: add support for implementation specific callbacks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out dw_mci_init_slot_caps to consolidate parsing
all differents types of capabilities from host contrllers.
No functional change intended.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 800d78bfcc ("mmc: dw_mmc: add support for implementation specific callbacks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The recent CTO timer introduced in commit 03de19212e ("mmc: dw_mmc:
introduce timer for broken command transfer over scheme") was causing
observable problems due to race conditions. Previous patches have
fixed those race conditions.
It can be observed that these same race conditions ought to be
theoretically possible with the DTO timer too though they are
massively less likely to happen because the data timeout is always set
to 0xffffff right now. That means even at a 200 MHz card clock we
were arming the DTO timer for 94 ms:
>>> (0xffffff * 1000. / 200000000) + 10
93.886075
We always also were setting the DTO timer _after_ starting the
transfer, unlike how the old code was seting the CTO timer.
In any case, even though the DTO timer is much less likely to have
races, it still makes sense to add code to handle it _just in case_.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Just like the CTO timeout calculation introduced recently, the DTO
timeout calculation was incorrect. It used "bus_hz" but, as far as I
can tell, it's supposed to use the card clock. Let's account for the
div value, which is documented as 2x the value stored in the register,
or 1 if the register is 0.
NOTE: This was likely not terribly important until commit 16a34574c6
("mmc: dw_mmc: remove the quirks flags") landed because "DIV" is
documented on Rockchip SoCs (the ones that used to define the quirk)
to always be 0 or 1. ...and, in fact, it's documented to only be 1
with EMMC in 8-bit DDR52 mode. Thus before the quirk was applied to
everyone it was mostly OK to ignore the DIV value.
I haven't personally observed any problems that are fixed by this
patch but I also haven't tested this anywhere with a DIV other an 0.
AKA: this problem was found simply by code inspection and I have no
failing test cases that are fixed by it. Presumably this could fix
real bugs for someone out there, though.
Fixes: 16a34574c6 ("mmc: dw_mmc: remove the quirks flags")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This attempts to instill a bit of paranoia to the code dealing with
the CTO timer. It's believed that this will make the CTO timer more
robust in the case that we're having very long interrupt latencies.
Note that I originally thought that perhaps this patch was being
overly paranoid and wasn't really needed, but then while I was running
mmc_test on an rk3399 board I saw one instance of the message:
dwmmc_rockchip fe320000.dwmmc: Unexpected interrupt latency
I had debug prints in the CTO timer code and I found that it was
running CMD 13 at the time.
...so even though this patch seems like it might be overly paranoid,
maybe it really isn't?
Presumably the bad interrupt latency experienced was due to the fact
that I had serial console enabled as serial console is typically where
I place blame when I see absurdly large interrupt latencies. In this
particular case there was an (unrelated) printout to the serial
console just before I saw the "Unexpected interrupt latency" printout.
...and actually, I managed to even reproduce the problems by running
"iw mlan0 scan > /dev/null" while mmc_test was running. That not only
does a bunch of PCIe traffic but it also (on my system) outputs some
SELinux log spam.
Fixes: 03de19212e ("mmc: dw_mmc: introduce timer for broken command transfer over scheme")
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the commit 03de19212e ("mmc: dw_mmc: introduce timer for broken
command transfer over scheme") we tried to calculate the expected
hardware command timeout value. Unfortunately that calculation isn't
quite correct in all cases. It used "bus_hz" but, as far as I can
tell, it's supposed to use the card clock. Let's account for the div
value, which is documented as 2x the value stored in the register, or
1 if the register is 0.
NOTE: It's not expected that this will actually fix anything important
since the 10 ms margin added by the function will pretty much dwarf
any calculations. The card clock should be 100 kHz at minimum and:
1000 ms/s * (255 * 2) / 100000 Hz.
Gives us 5.1 ms.
...so really the point of this patch is just to make the code more
"correct" in case anyone ever tries to remove the 10 ms buffer.
Fixes: 03de19212e ("mmc: dw_mmc: introduce timer for broken command transfer over scheme")
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When running with the commit 03de19212e ("mmc: dw_mmc: introduce
timer for broken command transfer over scheme") I found this message
in the log:
Unexpected command timeout, state 7
It turns out that we weren't properly cancelling the new CTO timer in
the case that a voltage switch was done. Let's promote the cancel
into the dw_mci_cmd_interrupt() function to fix this.
Fixes: 03de19212e ("mmc: dw_mmc: introduce timer for broken command transfer over scheme")
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Don't populate the const arrays mszs on the stack, instead make them
static. Makes the object code smaller by over 310 bytes:
Before:
text data bss dec hex filename
47527 8528 320 56375 dc37 drivers/mmc/host/dw_mmc.o
After:
text data bss dec hex filename
47055 8688 320 56063 daff drivers/mmc/host/dw_mmc.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per the databook of designware mmc controller 2.70a, table 3-2, cmd
done interrupt should be fired as soon as the the cmd is sent via
cmd line. And the response timeout interrupt should be generated
unconditioinally as well if the controller doesn't receive the resp.
However that doesn't seem to meet the fact of rockchip specified Soc
platforms using dwmmc. We have continuously found the the cmd done or
response timeout interrupt missed somehow which took us a long time to
understand what was happening. Finally we narrow down the root to
the reconstruction of sample circuit for dwmmc IP introduced by
rockchip and the buggy design sweeps over all the existing rockchip
Socs using dwmmc disastrously.
It seems no way to work around this bug without the proper break-out
mechanism so that we seek for a parallel pair the same as the handling
for missing data response timeout, namely dto timer. Adding this cto
timer seems easily to handle this bug but it's hard to restrict the code
under the rockchip specified context. So after merging this patch, it
sets up the cto timer for all the platforms using dwmmc IP which isn't
ideal but at least we don't advertise new quirk here. Fortunately, no
obvious performance regression was found by test and the pre-existing
similar catch-all timer for sdhci has proved it's an acceptant way to
make the code as robust as possible.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196321
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
[shawn.lin: rewrite the code and the commit msg throughout]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This commit modifies dw_mci_probe(), it moves reset assertion before
drv_data->init(host)
Some driver needs to access controller registers in its .init() ops. So,
in order to make such access safe, we should do controller reset before
.init() being called.
Signed-off-by: Wei Li <liwei213@huawei.com>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Chen Jun <chenjun14@huawei.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change to print the information about when the deprecated "num-slots" DT
binding is being used, as to avoid confusion when browsing the log:
dwmmc_rockchip fe320000.dwmmc: 'num-slots' was deprecated.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: d30a8f7bdf ("mmc: dw_mmc: deprecated the "num-slots" property")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the 'cur_slot'. Instead, just use 'slot'.
There is no multiple slots, so we need to consider only one slot.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Doesn't need to pass the id value for slot functions.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It doesn't need to use the array of slots anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dwmmc controller has used the only one slot.
It doesn't need to check the other slots.
Remove the loop about finding slots.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dwmmc controller is supporting only one slot per a IP.
Even though DWMMC IP is provided the multiple slot, but there is no
usage in real world.
In mmc subsystem, not allow the multiple slot concept.
Then "num-slots" property is deprecated.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.comi>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using the device_property interfaces allows the dw_mmc driver to work
on platforms which run on either device tree or ACPI.
Signed-off-by: David Woods <dwoods@mellanox.com>
Reviewed-by: Chris Metcalf <cmetcalf@mellanox.com>
Cc: stable@vger.linux.org
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit a6db2c8603 ("mmc: dw_mmc: Don't allow Runtime PM for
SDIO cards")'
As dw_mmc now is capable of preventing runtime PM suspend while SDIO IRQs
are enabled, let's drop the less fine-grained method, which is preventing
runtime PM suspend for all SDIO cards - no matter of whether SDIO IRQs are
being enabled or not.
In this way we don't keep the host runtime PM resumed, unless it's really
needed, thus avoiding to waste power.
Especially when SDIO IRQs is supported via a separate out-of-band IRQ line,
which isn't defined by the SDIO standard, typically the SDIO func driver
doesn't enable SDIO IRQs via sdio_claim_irq(). So, for these cases we can
now allow the dwmmc device to be runtime PM suspended in-between requests.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
To be able to handle SDIO IRQs the dw_mmc device needs to be powered and
providing clock to the SDIO card. Therefore, we must not allow the device
to be runtime PM suspended while SDIO IRQs are enabled.
To fix this, let's increase the runtime PM usage count while the mmc core
enables SDIO IRQs. Later when the mmc core tells dw_mmc to disable SDIO
IRQs, we drop the usage count to again allow runtime PM suspend.
This now becomes the default behaviour for dw_mmc. In cases where SDIO IRQs
can be re-routed as GPIO wake-ups during runtime PM suspend, one could
potentially allow runtime PM suspend. However, that will have to be
addressed as a separate change on top of this one.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Convert to use the more lightweight method for processing SDIO IRQs, which
involves the following changes:
- Enable MMC_CAP2_SDIO_IRQ_NOTHREAD when SDIO IRQ is supported and use
sdio_signal_irq() instead of mmc_signal_sdio_irq().
- Mask the SDIO IRQ before signaling a new one to be processed.
- Implement the ->ack_sdio_irq() callback to unmask the SDIO IRQ.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Too much condition iteration makes the code
less readable. Slightly improve it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No need to declar it there, remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Peter Ujfalusi