MSM sd host controller is capable of HW busy detection of device busy
signaling over DAT0 line. And it requires the R1B response for commands
that have this response associated with them.
So set the below two host capabilities for qcom SDHC.
- MMC_CAP_WAIT_WHILE_BUSY
- MMC_CAP_NEED_RSP_BUSY
Recent development of the mmc core in regards to this, revealed this as
being a potential bug, hence the stable tag.
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1587363626-20413-2-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When SDHC gets reset (E.g. in runtime suspend path), CQE also gets
reset and goes to disable state. But s/w state still points it as CQE
is in enabled state. Since s/w and h/w states goes out of sync,
it results in s/w request timeout for subsequent CQE requests.
To synchronize CQE s/w and h/w state during SDHC reset,
explicitly deactivate CQE just before SDHC reset.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1583503724-13943-3-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHC core with new 14lpp and later tech DLL should not enable
PWRSAVE_DLL since such controller's internal gating cannot meet
following MCLK requirement:
When MCLK is gated OFF, it is not gated for less than 0.5us and MCLK
must be switched on for at-least 1us before DATA starts coming.
Adding support for this requirement.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1581077075-26011-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This function is not exported and only used in this file. Mark it static.
Cc: Ritesh Harjani <riteshh@codeaurora.org>
Cc: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Fixes: 87a8df0dce ("mmc: sdhci-msm: Add CQHCI support for sdhci-msm")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200206162124.201195-1-swboyd@chromium.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The DDR_CONFIG register offset got updated after a specific
minor version of sdcc V4. This offset change has not been properly
taken care of while updating register changes for sdcc V5.
Correcting proper offset for this register.
Also updating this register value to reflect the recommended RCLK
delay.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/0101016ea738ec72-fa0f852d-20f8-474a-80b2-4b0ef63b132c-000000@us-west-2.amazonses.com
Fixes: f15358885d ("mmc: sdhci-msm: Define new Register address map")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The newly added sdhci_msm_restore_sdr_dll_config() function is only called
if CONFIG_PM is enabled:
drivers/mmc/host/sdhci-msm.c:1050:12: error:
'sdhci_msm_restore_sdr_dll_config' defined but not used
[-Werror=unused-function]
Better remove the incorrect #ifdef altogether and just use __maybe_unused,
which is harder to get wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Clock Data Recovery (CDR) circuit allows to automatically adjust
the RX sampling-point/phase for high frequency cards (SDR104, HS200...).
CDR is automatically enabled during DLL configuration.
However, according to the APQ8016 reference manual, this function
must be disabled during TX and tuning phase in order to prevent any
interferences during tuning challenges and unexpected phase alteration
during TX transfers.
This patch enables/disables CDR according to the current transfer mode.
This fixes sporadic write transfer issues observed with some SDR104 and
HS200 cards.
Inspired by sdhci-msm downstream patch:
https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/432516/
Reported-by: Leonid Segal <leonid.s@variscite.com>
Reported-by: Manabu Igusa <migusa@arrowjapan.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On few SDHCI-MSM controllers, the host controller's clock tuning
circuit may go out of sync if controller clocks are gated which
eventually will result in data CRC, command CRC/timeout errors.
To overcome this h/w limitation, the DLL needs to be re-initialized
and restored with its old settings once clocks are ungated.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support to use the new compatible string "qcom,sdhci-msm-v5".
Based on the msm variant, pick the relevant variant data and
use it for register read/write to msm specific registers.
Signed-off-by: Sayali Lokhande <sayalil@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In addition to offsets of certain registers changing, the registers in
core_mem have been shifted to HC mem as well. To access these
registers, define msm version specific functions. These functions can
be loaded into the function pointers at the time of probe based on
the msm version detected.
Also defind new data structure to hold version specific Ops and
register addresses.
Signed-off-by: Sayali Lokhande <sayalil@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For SDCC version 5.0.0, MCI registers are removed from SDCC
interface and some registers are moved to HC.
Define a new data structure where we can statically define
the address offsets for the registers in different SDCC versions.
Signed-off-by: Sayali Lokhande <sayalil@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now we have a proper implementation for the power irq handling and this
quirk is not needed anymore. In fact, it is causing card detection delays
on apq8096 platforms and the following error is displayed:
sdhci_msm 74a4900.sdhci: mmc0: pwr_irq for req: (4) timed out
The quirk is forcing the controller to retain 1.8V signalling on the slot
even when a new card is inserted, which is not correct. The proper behavior
would be to reset the controller in order to start with 3.3V signaling.
Fixes: c0309b3803 ("mmc: sdhci-msm: Add sdhci msm register write APIs which wait for pwr irq")
Suggested-by: Vijay Viswanath <vviswana@codeaurora.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The PADs for SD card are dual-voltage that support 3v/1.8v. Those PADs
have a control signal (io_pad_pwr_switch/mode18 ) that indicates
whether the PAD works in 3v or 1.8v.
SDHC core on msm platforms should have IO_PAD_PWR_SWITCH bit set/unset
based on actual voltage used for IO lines. So when power irq is
triggered for io high or io low, the driver should check the voltages
supported and set the pad accordingly.
Signed-off-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
During probe check whether the vdd-io regulator of sdhc platform device
can support 1.8V and 3V and store this information as a capability of
platform device.
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Not all instances of the SDCC core supports changing signal voltage and
as such will not generate a power interrupt when the software attempts
to change the voltage. This results in probing the eMMC on some devices
to take over 2 minutes.
Check that the SWITCHABLE_SIGNALING_VOLTAGE bit in MCI_GENERICS is set
before waiting for the power interrupt.
Cc: Sahitya Tummala <stummala@codeaurora.org>
Cc: Vijay Viswanath <vviswana@codeaurora.org>
Fixes: c0309b3803 ("mmc: sdhci-msm: Add sdhci msm register write APIs which wait for pwr irq")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The __WARN_printf() function is not portable across architectures
and causes a compile-time error on x86 and others that don't use
the asm-generic version of asm/bug.h:
drivers/mmc/host/sdhci-msm.c: In function 'sdhci_msm_check_power_status':
drivers/mmc/host/sdhci-msm.c:1066:4: error: implicit declaration of function '__WARN_printf'; did you mean '__dev_printk'? [-Werror=implicit-function-declaration]
__WARN_printf("%s: pwr_irq for req: (%d) timed out\n",
^~~~~~~~~~~~~
The change that introduced this error, "mmc: sdhci-msm: Add sdhci msm
register write APIs which wait for pwr irq", likely meant to use
dev_warn(), so I'm changing over to that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Register writes which change voltage of IO lines or turn the IO bus
on/off require controller to be ready before progressing further. When
the controller is ready, it will generate a power irq which needs to be
handled. The thread which initiated the register write should wait for
power irq to complete. This will be done through the new sdhc msm write
APIs which will check whether the particular write can trigger a power
irq and wait for it with a timeout if it is expected.
The SDHC core power control IRQ gets triggered when -
* There is a state change in power control bit (bit 0)
of SDHCI_POWER_CONTROL register.
* There is a state change in 1.8V enable bit (bit 3) of
SDHCI_HOST_CONTROL2 register.
* Bit 1 of SDHCI_SOFTWARE_RESET is set.
Also add support APIs which are used by sdhc msm write APIs to check
if power irq is expected to be generated and wait for the power irq
to come and complete if the irq is expected.
This patch requires CONFIG_MMC_SDHCI_IO_ACCESSORS to be enabled.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a rare scenario in HW, where the first clear pulse could
be lost when the actual reset and clear/read of status register
are happening at the same time. Fix this by retrying upto 10 times
to ensure the status register gets cleared. Otherwise, this will
lead to a spurious power IRQ which results in system instability.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDCC controller reset (SW_RST) during probe may trigger power irq if
previous status of PWRCTL was either BUS_ON or IO_HIGH_V. So before we
enable the power irq interrupt in GIC (by registering the interrupt
handler), we need to ensure that any pending power irq interrupt status
is acknowledged otherwise power irq interrupt handler would be fired
prematurely.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The delay circuit used to support HS400 is calibrated based on two
additional clocks. When these clocks are not available and
FF_CLK_SW_RST_DIS is not set in CORE_HC_MODE, reset might fail. But on
some platforms this doesn't work properly and below dump can be seen in
the kernel log.
mmc0: Reset 0x1 never completed.
mmc0: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc0: sdhci: Sys addr: 0x00000000 | Version: 0x00001102
mmc0: sdhci: Blk size: 0x00004000 | Blk cnt: 0x00000000
mmc0: sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
mmc0: sdhci: Present: 0x01f80000 | Host ctl: 0x00000000
mmc0: sdhci: Power: 0x00000000 | Blk gap: 0x00000000
mmc0: sdhci: Wake-up: 0x00000000 | Clock: 0x00000002
mmc0: sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
mmc0: sdhci: Int enab: 0x00000000 | Sig enab: 0x00000000
mmc0: sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
mmc0: sdhci: Caps: 0x742dc8b2 | Caps_1: 0x00008007
mmc0: sdhci: Cmd: 0x00000000 | Max curr: 0x00000000
mmc0: sdhci: Resp[0]: 0x00000000 | Resp[1]: 0x00000000
mmc0: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000
mmc0: sdhci: Host ctl2: 0x00000000
mmc0: sdhci: ============================================
Add support for the additional calibration clocks to allow these
platforms to be configured appropriately.
Cc: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Cc: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By stuffing the runtime controlled clocks into a clk_bulk_data array we
can utilize the newly introduced bulk clock operations and clean up the
error paths. This allow us to handle additional clocks in subsequent
patch, without the added complexity.
Cc: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Programming legacy HOST SDMA Buffer Boundary bits in Block Size Register
(0x04) is not supported in Qualcomm sdhci controllers. Writing to this
would cause the controller not to transfer last block in case block size
is 4 bytes or less.
This issue was noticed while testing sdio wlan card on Qcom DB410c board.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The spin lock is not necessary in set_ios. Anything that is racing with
changes to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host. So remove spin_lock and friends
from sdhci_set_ios and related callbacks.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
This removes CDC init sequence comments which are
not useful anyway.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
platform_execute_tuning should not really exist as it does not
do anything useful.
So remove this ops and directly plug sdhci_msm_execute_tuning
with mmc_host_ops.
Also in case of HS400 tuning clear SDHCI_HS400_TUNING flag once
HS400 related mode selection is done.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This provides enhanced_strobe mode feature support in sdhci-msm
driver.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
During tuning execution for HS400 mode, HW sequence recommends
to select MCLK_SEL/2(0x3) in VENDOR_SPEC & sdhc msm clock at GCC
to be 400MHZ (nearest supported clk). Add this change in tuning
sequence during HS400 tuning.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Program CORE_CSR_CDC_DELAY_CFG for hardware recommended 1.25ns delay.
We may see data CRC errors if it's programmed for any other delay
value.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The vendor specific func register doesn't get reset when using the
software reset register. The various bootloader's could leave this
in an unknown state, hence reset this register to it's power on reset
value during probe.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out sdhci_msm_hs400 used for DLL calibration in HS400
modes. This function will be needed for enhanced_strobe as well.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out msm_set/get_clock_rate_for_bus_mode for it's later
use in changing the tuning sequence for selecting HS400
bus speed mode.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This factors out sdhci_msm_hc_select_mode to later use
it during enhanced_strobe mode select.
It also further breaks sdhci_msm_hc_select_mode
into separate functions for configuring HS400 mode
or other modes.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The newer msm sdhci's cores use a different DLL hardware for HS400.
Update the configuration and calibration of the newer DLL block.
The HS400 DLL block used previously is CDC LP 533 and requires
programming multiple registers and waiting for configuration to
complete and then enable it. It has about 18 register writes and
two register reads.
The newer HS400 DLL block is SDC4 DLL and requires two register
writes for configuration and one register read to confirm that it
is initialized. There is an additional register write to enable
the power save mode for SDC4 DLL block.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Krishna Konda <kkonda@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In HS400 mode a new RCLK is introduced on the interface for read data
transfers. The eMMC5.0 device transmits the read data to the host with
respect to rising and falling edges of RCLK. In order to ensure correct
operation of read data transfers in HS400 mode, the incoming RX data
needs to be sampled by delayed version of RCLK.
The CDCLP533 delay circuit shifts the RCLK by T/4. It needs to be
initialized, configured and enabled once during HS400 mode switch and
when operational voltage/clock is changed.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Save the tuning phase once the tuning is performed.
This phase value will be used while calibrating DLL
for HS400 mode.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The following msm platform specific changes are added to support HS400.
- Allow tuning for HS400 mode.
- Configure HS400 timing mode using the VENDOR_SPECIFIC_FUNC register.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHC MSM controller need 2x clock for MCLK at GCC.
Hence make required changes to have 2x clock for
DDR timing modes.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci-msm controller may have different clk-rates for each
bus speed mode. Thus implement set_clock callback for
sdhci-msm driver.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This add get_min_clock() and get_max_clock() callback
for sdhci-msm. sdhci-msm min/max clocks may be different
hence implement these callbacks.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDCC core with minor version >= 0x42 introduced new 14lpp
DLL. This has additional requirements in the reset sequence
for DLL tuning. Make necessary changes as needed.
Without this patch we see below errors on such SDHC controllers
sdhci_msm 7464900.sdhci: mmc0: DLL failed to LOCK
mmc0: tuning execution failed: -110
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch changes the poor style of writel/readl registers
into more readable format. This avoid mixed style format
of readl/writel in sdhci-msm driver.
This patch also removes the one line comments which were present for
above writel/readl, since they were of no help.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Provides runtime PM callbacks to enable and disable clock resources
when idle. Also support system PM callbacks to be called during system
suspend and resume.
Reviewed-by: Ritesh Harjani <riteshh@codeaurora.org>
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Tested-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Pramod Gurav <pramod.gurav@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Veerabhadrarao Badiganti