When using VXLAN tunnels and a sky2 device, I have experienced
checksum failures of the following type:
[ 4297.761899] eth0: hw csum failure
[...]
[ 4297.765223] Call Trace:
[ 4297.765224] <IRQ> [<ffffffff8172f026>] dump_stack+0x46/0x58
[ 4297.765235] [<ffffffff8162ba52>] netdev_rx_csum_fault+0x42/0x50
[ 4297.765238] [<ffffffff8161c1a0>] ? skb_push+0x40/0x40
[ 4297.765240] [<ffffffff8162325c>] __skb_checksum_complete+0xbc/0xd0
[ 4297.765243] [<ffffffff8168c602>] tcp_v4_rcv+0x2e2/0x950
[ 4297.765246] [<ffffffff81666ca0>] ? ip_rcv_finish+0x360/0x360
These are reliably reproduced in a network topology of:
container:eth0 == host(OVS VXLAN on VLAN) == bond0 == eth0 (sky2) -> switch
When VXLAN encapsulated traffic is received from a similarly
configured peer, the above warning is generated in the receive
processing of the encapsulated packet. Note that the warning is
associated with the container eth0.
The skbs from sky2 have ip_summed set to CHECKSUM_COMPLETE, and
because the packet is an encapsulated Ethernet frame, the checksum
generated by the hardware includes the inner protocol and Ethernet
headers.
The receive code is careful to update the skb->csum, except in
__dev_forward_skb, as called by dev_forward_skb. __dev_forward_skb
calls eth_type_trans, which in turn calls skb_pull_inline(skb, ETH_HLEN)
to skip over the Ethernet header, but does not update skb->csum when
doing so.
This patch resolves the problem by adding a call to
skb_postpull_rcsum to update the skb->csum after the call to
eth_type_trans.
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AVM BlueFritz! USB controllers had a special handling in the
Bluetooth core when it comes to reading the supported commands.
Both drivers now set the HCI_QUIRK_BROKEN_LOCAL_COMMANDS and with
that it is no longer needed to look for vendor specific details.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The AVM BlueFritz! 2.0 USB dongles do not support the HCI command for
reading the local supported commands. So set this quirk to let the
core know about it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The AVM BlueFritz! 1.0 USB dongles do not support the HCI command for
reading the local supported commands. So set this quirk to let the
core know about it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some controllers advertise support for Bluetooth 1.2 specification,
but they do not support the HCI Read Local Supported Commands command.
If that is the case, then the driver can quirk the behavior and force
the core to skip this command. This will allow removing vendor specific
checks out of the core.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The __ldcw macro has a problem when its argument needs to be reloaded from
memory. The output memory operand and the input register operand both need to
be reloaded using a register in class R1_REGS when generating 64-bit code.
This fails because there's only a single register in the class. Instead, use a
memory clobber. This also makes the __ldcw macro a compiler memory barrier.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Helge Deller <deller@gmx.de>
The total stream number of Skylake's input and output stream
exceeds 15, which will cause some streams do not work because
of the overflow on SDxCTL.STRM field if using the legacy
stream tag allocation method.
This patch uses the new stream tag allocation method by add
the flag AZX_DCAPS_SEPARATE_STREAM_TAG for Skylake platform.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Implemented separate stream_tag assignment for input and output streams.
According to hda specification stream tag must be unique throughout the
input streams group, however an output stream might use a stream tag
which is already in use by an input stream. This change is necessary
to support HW which provides a total of more than 15 stream DMA engines
which with legacy implementation causes an overflow on SDxCTL.STRM
field (and the whole SDxCTL register) and as a result usage of
Reserved value 0 in the SDxCTL.STRM field which confuses HDA controller.
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull drm fixes from Dave Airlie:
"Xmas fixes pull:
core:
one atomic fix, revert the WARN_ON dumb buffers patch.
agp:
fixup Dave J.
nouveau:
fix 3.18 regression for old userspace
tegra fixes:
vblank and iommu fixes
amdkfd:
fix bugs shown by testing with userspace, init apertures once
msm:
hdmi fixes and cleanup
i915:
misc fixes
There is also a link ordering fix that I've asked to be cc'ed to you,
putting iommu before gpu, it fixes an issue with amdkfd when things
are all in the kernel, but I didn't like sending it via my tree
without discussion.
I'll probably be a bit on/off for a few weeks with pulls now, due to
holidays and LCA, so don't be surprised if stuff gets a bit backed up,
and things end up a bit large due to lag"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (28 commits)
Revert "drm/gem: Warn on illegal use of the dumb buffer interface v2"
agp: Fix up email address & attributions in AGP MODULE_AUTHOR tags
nouveau: bring back legacy mmap handler
drm/msm/hdmi: rework HDMI IRQ handler
drm/msm/hdmi: enable regulators before clocks to avoid warnings
drm/msm/mdp5: update irqs on crtc<->encoder link change
drm/msm: block incoming update on pending updates
drm/atomic: fix potential null ptr on plane enable
drm/msm: Deletion of unnecessary checks before the function call "release_firmware"
drm/msm: Deletion of unnecessary checks before two function calls
drm/tegra: dc: Select root window for event dispatch
drm/tegra: gem: Use the proper size for GEM objects
drm/tegra: gem: Flush buffer objects upon allocation
drm/tegra: dc: Fix a potential race on page-flip completion
drm/tegra: dc: Consistently use the same pipe
drm/irq: Add drm_crtc_vblank_count()
drm/irq: Add drm_crtc_handle_vblank()
drm/irq: Add drm_crtc_send_vblank_event()
drm/i915: Disable PSMI sleep messages on all rings around context switches
drm/i915: Force the CS stall for invalidate flushes
...
One that lockdep turned up, I didn't go far enough with cleanup
of attributes for IPMI. This has been there a long time; my
previous fix of this didn't fix all the attributes.
One fix for some arches that need an explicit linux/ctype.h for
isspace().
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlSXWLcACgkQIXnXXONXERd+LACeKXjsGiTpTUe4vjnOsJj8oLPg
I80AmwT20SVzlxGSVqSrwBn6uVirwjs5
=ByuY
-----END PGP SIGNATURE-----
Merge tag 'for-linus-2' of git://git.code.sf.net/p/openipmi/linux-ipmi
Pull ipmi driver bugfixes from Corey Minyard:
"Fix two bugs:
One that lockdep turned up, I didn't go far enough with cleanup of
attributes for IPMI. This has been there a long time; my previous fix
of this didn't fix all the attributes.
One fix for some arches that need an explicit linux/ctype.h for
isspace()"
* tag 'for-linus-2' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi: Fix compile issue with isspace()
ipmi: Finish cleanup of BMC attributes
net/openvswitch/vport-gre.c:188:5-11: inconsistent IS_ERR and PTR_ERR, PTR_ERR on line 189
PTR_ERR should access the value just tested by IS_ERR
Semantic patch information:
There can be false positives in the patch case, where it is the call
IS_ERR that is wrong.
Generated by: scripts/coccinelle/tests/odd_ptr_err.cocci
CC: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When connectable mode is enabled (page scan on) through some non-mgmt
method the HCI_CONNECTABLE flag will not be set. For backwards
compatibility with user space versions not using mgmt we should not
require HCI_CONNECTABLE to be set if HCI_MGMT is not set.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 3.17+
When controllers set the HCI_QUIRK_INVALID_BDADDR flag, it is required
by userspace to program a valid public Bluetooth device address into
the controller before it can be used.
After successful address configuration, the internal state changes and
the controller runs the complete initialization procedure. However one
small difference is that this is no longer the HCI_SETUP stage. The
HCI_SETUP stage is only valid during initial controller setup. In this
case the stack runs the initialization as part of the HCI_CONFIG stage.
The controller version information, default name and supported commands
are only stored during HCI_SETUP. While these information are static,
they are not read initially when HCI_QUIRK_INVALID_BDADDR is set. So
when running in HCI_CONFIG state, these information need to be updated
as well.
This especially impacts Bluetooth 4.1 and later controllers using
extended feature pages and second event mask page.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org # 3.17+
Add tpc entry to ath9k debugfs in order to enable/disable hw TPC
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable hw TPC by default on AR9003 based chips
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove the function rtl8723be_phy_get_txpower_level() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove the function rtl92ee_get_available_desc() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With this change, all of the drivers now use the common routine. As this
driver has VHT capability, an additional parameter is needed, thus all the
drivers had to be modified.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The code uses macros to determine the parameters that are passed to the
rate setting routine. A simpler method is implemented.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The code uses macros to determine the parameters that are passed to the
rate setting routine. A simpler method is implemented.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Device RTL8821AE is the first if the rtlwifi devices to implement 802.11ac
capability. As a result, VHT rate descriptors are needed. In addition, the
driver is converted to use the descriptors in rtlwifi.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This common set of rate descriptors is renamed to be DESC_RATExx.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver is also converted to use the rate-mapping code in the core.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver duplicates a routine found in the core.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver currently has its owm version of this routine that duplicates
a routine in rtlwifi.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Four of the drivers (92ce, 92cu, 92de, and 92se) supply an argument to the
rate-mapping routine that is never used, thus it can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These changes match those of the latest vendor driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These changes were found in the latest vendor driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch applies changes found in the latest vendor driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This change helps the device maintain a connection.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Two of the macros that control power sequencing have values to be set that
contain bits that are not covered by the associated mask.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The existing method for loading both normal and WOWLAN firmware for the
device duplicates a lot of code. This solution is much cleaner.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The minimum number of pulses per burst on FCC radar type 5 is 1.
Use this number for correct radar detection.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Memory allocated by kmemdup() in rsi_load_ta_instructions() is leaked.
But duplication of firmware data here is useless,
so the patch removes kmemdup() at all.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove the function rtl92d_set_fw_pwrmode_cmd() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver looks for pdata->oob_irq_supported to find out if wowl can be
supported. However, not all platforms populate pdata in which case we crash
the kernel because of NULL pointer dereference.
Fixes: 330b4e4be9 ("brcmfmac: Add wowl support for SDIO devices.")
Reported-by: Christophe Prigent <christophe.prigent@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 24a0aa212e ("cfg80211: make WEXT compatibility unselectable")
made it impossible to depend on CFG80211_WEXT. It does still allow to
select that symbol. (Yes, the commit summary is confusing.)
So make IPW2200 select CFG80211_WEXT, so that the ipw2200 driver can be
enabled in config again.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A 1-byte burst size is rather inefficient and has been shown to cause
TX issues during testing. Increase the DMA burst size to 4-bytes for
both RX and TX DMA when using the 8-bit FIFO.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
skb_scrub_packet() is called when a packet switches between a context
such as between underlay and overlay, between namespaces, or between
L3 subnets.
While we already scrub the packet mark, connection tracking entry,
and cached destination, the security mark/context is left intact.
It seems wrong to inherit the security context of a packet when going
from overlay to underlay or across forwarding paths.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Flavio Leitner <fbl@sysclose.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When vlan tags are stacked, it is very likely that the outer tag is stored
in skb->vlan_tci and skb->protocol shows the inner tag's vlan_proto.
Currently netif_skb_features() first looks at skb->protocol even if there
is the outer tag in vlan_tci, thus it incorrectly retrieves the protocol
encapsulated by the inner vlan instead of the inner vlan protocol.
This allows GSO packets to be passed to HW and they end up being
corrupted.
Fixes: 58e998c6d2 ("offloading: Force software GSO for multiple vlan tags.")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar says:
====================
openvswitch: datapath fixes
Following patch series is mostly targeted to MPLS fixes. other
patches are related datapth transmit path error handling.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error vxlan_xmit_one() can free already freed skb.
Also fixes memory leak of dst-entry.
Fixes: acbf74a763 ("vxlan: Refactor vxlan driver to make use
of the common UDP tunnel functions").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today vport-send has complex error handling because it involves
freeing skb and updating stats depending on return value from
vport send implementation.
This can be simplified by delegating responsibility of freeing
skb to the vport implementation for all cases. So that
vport-send needs just update stats.
Fixes: 91b7514cdf ("openvswitch: Unify vport error stats
handling")
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPLS GSO needs to know inner most protocol to process GSO packets.
Fixes: 25cd9ba0ab ("openvswitch: Add basic MPLS support to
kernel").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux stack does not implement GSO for packet with multiple
encapsulations. Therefore there was check in MPLS action
validation to detect such case, But this check introduced
bug which deleted one or more actions from actions list.
Following patch removes this check to fix the validation.
Fixes: 25cd9ba0ab ("openvswitch: Add basic MPLS support to
kernel").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reported-by: Srinivas Neginhal <sneginha@vmware.com>
Acked-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPLS and Tunnel GSO does not work together. Reject packet which
request such GSO.
Fixes: 0d89d2035f ("MPLS: Add limited GSO support").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes MPLS GSO for case when mpls is compiled as kernel module.
Fixes: 0d89d2035f ("MPLS: Add limited GSO support").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jay Vosburgh