Deferred probe is an expected return value for tegra_fuse_readl().
Given that the driver deals with it properly, there's no need to
output a warning that may potentially confuse users.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the XUSB pad controller found on Tegra194 SoCs. It is
mostly similar to the same IP found on Tegra186, but the number of
pads exposed differs, as do the programming sequences. Because most of
the Tegra194 XUSB PADCTL registers definition and programming sequence
are the same as Tegra186, Tegra194 XUSB PADCTL can share the same
driver, xusb-tegra186.c, with Tegra186 XUSB PADCTL.
Tegra194 XUSB PADCTL supports up to USB 3.1 Gen 2 speed, however, it
is possible for some platforms have long signal trace that could not
provide sufficient electrical environment for Gen 2 speed. This patch
adds a "maximum-speed" property to usb3 ports which can be used to
specify the maximum supported speed for any particular USB 3.1 port.
For a port that is not capable of SuperSpeedPlus, "maximum-speed"
property should carry "super-speed".
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As xusb-tegra186.c will be reused for Tegra194, it would be good to
protect Tegra186 soc data with CONFIG_ARCH_TEGRA_186_SOC. This commit
also reshuffles Tegra186 soc data single CONFIG_ARCH_TEGRA_186_SOC
will be sufficient.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for set_mode on UTMI phy. This allow XUSB host/device mode
drivers to configure the hardware to corresponding modes.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for set_mode on USB 2 phy. This allow XUSB host/device mode
drivers to configure the hardware to corresponding modes.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra XUSB host, device mode driver requires the USB 3 companion port
number for corresponding USB 2 port. Add API to retrieve the same.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For USB 2 ports that has usb-role-switch enabled, add usb-phy for
corresponding USB 2 phy. USB role changes from role switch are then
updated to corresponding host and device mode drivers via usb-phy notifier
block.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
[treding@nvidia.com: rebase onto Greg's usb-next branch]
Signed-off-by: Thierry Reding <treding@nvidia.com>
If usb-role-switch property is present in USB 2 port, register
usb-role-switch to receive usb role changes.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
[treding@nvidia.com: rebase onto Greg's usb-next branch]
Signed-off-by: Thierry Reding <treding@nvidia.com>
*) Fix phy_get() from erroring out if device link creation failed
*) Fix write timeouts in Motorola Mapphone mdm6600 PHY
*) Fix Broadcom brcm-sata PHY driver to write to the correct MDIO register
*) Add GMII PHY mode in supported modes of TI AM335x/437x/5xx SoCs
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=iSMT
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.6-rc_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
phy: for 5.6-rc
*) Fix phy_get() from erroring out if device link creation failed
*) Fix write timeouts in Motorola Mapphone mdm6600 PHY
*) Fix Broadcom brcm-sata PHY driver to write to the correct MDIO register
*) Add GMII PHY mode in supported modes of TI AM335x/437x/5xx SoCs
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.6-rc_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
phy: mapphone-mdm6600: Fix timeouts by adding wake-up handling
phy: brcm-sata: Correct MDIO operations for 40nm platforms
phy: ti: gmii-sel: do not fail in case of gmii
phy: ti: gmii-sel: fix set of copy-paste errors
phy: core: Fix phy_get() to not return error on link creation failure
phy: mapphone-mdm6600: Fix write timeouts with shorter GPIO toggle interval
This adds support for the PCI PHY found in the Amlogic AXG SoC Family.
This will allow to mutualize code in pci-meson.c between AXG and G12A
SoC.
This PHY also uses and chains an analog PHY, which on AXG platform
is needed to have reliable PCIe communication.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
This adds support for the MIPI analog PHY which is also used for PCIE
found in the Amlogic AXG SoC Family.
MIPI or PCIE selection is done by the #phy-cells, making the mode
static and exclusive.
For now only PCIE functionality is supported.
This PHY will be used to replace the mipi_enable clock gating logic
which was mistakenly added in the clock subsystem. This also activates
a non documented band gap bit in those registers that allows reliable
PCIE clock signal generation on AXG platforms.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
We have an interrupt handler for the wake-up GPIO pin, but we're missing
the code to wake-up the system. This can cause timeouts receiving data
for the UART that shares the wake-up GPIO pin with the USB PHY.
All we need to do is just wake the system and kick the autosuspend
timeout to fix the issue.
Fixes: 5d1ebbda03 ("phy: mapphone-mdm6600: Add USB PHY driver for MDM6600 on Droid 4")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
qcom_qmp_phy_init() is extended to support the additional register
writes needed in PCS MISC and the appropriate sequences and resources
are defined for the GEN2 PCIe QMP PHY found in SDM845.
Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The logic to write to MDIO registers on 40nm platforms was wrong
because it would use the port number as an offset from the base address
rather than the bank address of the PHY. This is hardly noticeable
because the only programming we do is enabling SSC or not, which is not
really causing an observable functional change.
Correct that mistake by passing down the struct brcm_sata_port structure
down to the brcm_sata_mdio_wr() and brcm_sata_mdio_rd() functions and do
the proper offsetting for 28nm, respectively 40nm platforms from there.
This means that brcm_sata_pcb_base() is now useless and is therefore
removed.
Fixes: c1602a1a0f ("phy: phy_brcmstb_sata: add support for MIPS-based platforms")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The "gmii" PHY interface mode is supported on TI AM335x/437x/5xx SoCs, so
don't fail if it's selected.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
- under PHY_INTERFACE_MODE_MII the 'mode' func parameter is assigned
instead of 'gmii_sel_mode' and it's working only because the default value
'gmii_sel_mode' is set to 0.
- console outputs use 'rgmii_id' and 'mode' values to print PHY mode
instead of using 'submode' value which is representing PHY interface mode
now.
This patch fixes above two cases.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
commit 987351e1ea ("phy: core: Add consumer device link support")
added device link support between PHY consumer and PHY provider.
However certain peripherals (DWC3 ULPI) have cyclic dependency
between the PHY provider and PHY consumer causing the device link
creation to fail.
Instead of erroring out on failure to create device link, only add a
debug print to indicate device link creation failed to get USB
working again in multiple platforms.
Fixes: 987351e1ea ("phy: core: Add consumer device link support")
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Alexandre TORGUE <alexandre.torgue@st.com>
I've noticed that when writing data to the modem the writes can time out
at some point eventually. Looks like kicking the modem idle GPIO every
600 ms instead of once a second fixes the issue. Note that this rate is
different from our runtime PM autosuspend rate MDM6600_MODEM_IDLE_DELAY_MS
that we still want to keep at 1 second, so let's add a separate define for
PHY_MDM6600_IDLE_KICK_MS.
Fixes: f7f50b2a7b ("phy: mapphone-mdm6600: Add runtime PM support for n_gsm on USB suspend")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Here is the big USB and Thunderbolt and PHY driver updates for 5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code has
begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXjFTNw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynpKQCgrh2FoobS2x0oFg/OUHdjokQV/BYAoJGWLOmt
8S5cnsCuLq3w5qpCcBva
=PMGd
-----END PGP SIGNATURE-----
Merge tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt/PHY driver updates from Greg KH:
"Here is the big USB and Thunderbolt and PHY driver updates for
5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code
has begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues"
[ Removed an incorrect compile test enablement for PHY_EXYNOS5250_SATA
that causes configuration warnings - Linus ]
* tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
Doc: ABI: add usb charger uevent
usb: phy: show USB charger type for user
usb: cdns3: fix spelling mistake and rework grammar in text
usb: phy: phy-gpio-vbus-usb: Convert to GPIO descriptors
USB: serial: cyberjack: fix spelling mistake "To" -> "Too"
USB: serial: ir-usb: simplify endpoint check
USB: serial: ir-usb: make set_termios synchronous
USB: serial: ir-usb: fix IrLAP framing
USB: serial: ir-usb: fix link-speed handling
USB: serial: ir-usb: add missing endpoint sanity check
usb: typec: fusb302: fix "op-sink-microwatt" default that was in mW
usb: typec: wcove: fix "op-sink-microwatt" default that was in mW
usb: dwc3: pci: add ID for the Intel Comet Lake -V variant
usb: typec: tcpci: mask event interrupts when remove driver
usb: host: xhci-tegra: set MODULE_FIRMWARE for tegra186
usb: chipidea: add inline for ci_hdrc_host_driver_init if host is not defined
usb: chipidea: handle single role for usb role class
usb: musb: fix spelling mistake: "periperal" -> "peripheral"
phy: ti: j721e-wiz: Fix build error without CONFIG_OF_ADDRESS
USB: usbfs: Always unlink URBs in reverse order
...
If CONFIG_OF_ADDRESS is not set and COMPILE_TEST=y, the following
error is seen while building phy-j721e-wiz.c
drivers/phy/ti/phy-j721e-wiz.o: In function `wiz_remove':
phy-j721e-wiz.c:(.text+0x1a): undefined reference to
`of_platform_device_destroy'
Fix the config dependency for PHY_J721E_WIZ here.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Signed-off-by: Hongbo Yao <yaohongbo@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20200117212310.2864-1-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
*) Add support in PHY core to create link between PHY consumer and PHY
provider
*) Add DisplayPort PHY configuration set to be used for negotiating the
configurations to be used between DisplayPort controller and
DisplayPort PHY
*) Add PHY wrapper driver (configure inputs to Cadence Sierra PHY) for
TI's J721E SoC and adapt Cadence Sierra PHY driver to be used for
J721E SoC (Supports USB and PCIe)
*) Add PHY driver for eMMC PHY in Intel LGM SoC
*) Add PHY support for 7216 and 7211 Broadcom SoCs which uses the new
Synopsys USB Controller
*) Add support for 16nm SATA PHY present in Broadcom 7216 SoC
*) Fix lost packet issue, fix MDIO from getting inaccessible, fix
occasional transaction failures, fix USB driver from crashing in
Broadcom USB PHY driver
*) Fix missing PCS SW reset in UFS PHY of Qualcomm SM8150
*) Use "struct phy_configure_opts_mipi_dphy" to pass parameters from
display controller to rockchip-inno-dsidphy
*) Other cleanups including compile testing for some of the PHY drivers,
fixing Kconfig indentation, duplicate writes in drivers etc.,
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=76zg
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 5.6
*) Add support in PHY core to create link between PHY consumer and PHY
provider
*) Add DisplayPort PHY configuration set to be used for negotiating the
configurations to be used between DisplayPort controller and
DisplayPort PHY
*) Add PHY wrapper driver (configure inputs to Cadence Sierra PHY) for
TI's J721E SoC and adapt Cadence Sierra PHY driver to be used for
J721E SoC (Supports USB and PCIe)
*) Add PHY driver for eMMC PHY in Intel LGM SoC
*) Add PHY support for 7216 and 7211 Broadcom SoCs which uses the new
Synopsys USB Controller
*) Add support for 16nm SATA PHY present in Broadcom 7216 SoC
*) Fix lost packet issue, fix MDIO from getting inaccessible, fix
occasional transaction failures, fix USB driver from crashing in
Broadcom USB PHY driver
*) Fix missing PCS SW reset in UFS PHY of Qualcomm SM8150
*) Use "struct phy_configure_opts_mipi_dphy" to pass parameters from
display controller to rockchip-inno-dsidphy
*) Other cleanups including compile testing for some of the PHY drivers,
fixing Kconfig indentation, duplicate writes in drivers etc.,
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (54 commits)
dt-bindings: phy: Add PHY_TYPE_DP definition
phy: ti: j721e-wiz: Fix return value check in wiz_probe()
dt-bindings: usb: Convert Allwinner A80 USB PHY controller to a schema
phy: intel-lgm-emmc: Fix warning by adding missing MODULE_LICENSE
phy: ti: j721e-wiz: Manage typec-gpio-dir
dt-bindings: phy: ti,phy-j721e-wiz: Add Type-C dir GPIO
phy: cadence: Sierra: add phy_reset hook
phy: cadence: Sierra: remove redundant initialization of pointer regmap
phy: Add DisplayPort configuration options
phy: Enable compile testing for some of drivers
phy: mediatek: Fix Kconfig indentation
phy: intel-lgm-emmc: Add support for eMMC PHY
dt-bindings: phy: intel-emmc-phy: Add YAML schema for LGM eMMC PHY
phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC
dt-bindings: phy: Document WIZ (SERDES wrapper) bindings
phy: cadence: Sierra: Use correct dev pointer in cdns_sierra_phy_remove()
phy: cadence: Sierra: Set cmn_refclk_dig_div/cmn_refclk1_dig_div frequency to 25MHz
phy: cadence: Sierra: Change MAX_LANES of Sierra to 16
phy: cadence: Sierra: Check for PLL lock during PHY power on
phy: cadence: Sierra: Get reset control "array" for each link
...
In case of error, the function devm_ioremap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
commit 95f1061f715e ("phy: intel-lgm-emmc: Add support for eMMC PHY")
introduces the below warning
WARNING: modpost: missing MODULE_LICENSE() in
drivers/phy/intel/phy-intel-emmc.o
Fix it by adding missing MODULE_LICENSE.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Based on this GPIO state we need to configure LN10
bit to swap lane0 and lane1 if required (flipped connector).
Type-C companions typically need some time after the cable is
plugged before and before they reflect the correct status of
Type-C plug orientation on the DIR line.
Type-C Spec specifies CC attachment debounce time (tCCDebounce)
of 100 ms (min) to 200 ms (max).
Use the DT property to figure out if we need to add delay
or not before sampling the Type-C DIR line.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Some platforms e.g. J721e need lane swap register
to be programmed before reset is deasserted.
This patch ensures that we propagate the phy_reset
back to the reset controller driver.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The pointer regmap is being initialized with a value that is never
read and it is being updated later with a new value from
phy->regmap_common_cdb. The initialization is redundant and can be
removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Some of the phy drivers can be compile tested to increase build
coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for eMMC PHY on Intel's Lightning Mountain SoC.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for WIZ module present in TI's J721E SoC. WIZ is a SERDES
wrapper used to configure some of the input signals to the SERDES. It is
used with both Sierra(16G) and Torrent(10G) SERDES. This driver configures
three clock selects (pll0, pll1, dig), two divider clocks and supports
resets for each of the lanes.
[jsarha@ti.com: Add support for Torrent(10G) SERDES wrapper]
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
commit 44d30d6228 ("phy: cadence: Add driver for Sierra PHY"),
incorrectly used parent device pointer to get driver data. Fix it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Set cmn_refclk_dig_div/cmn_refclk1_dig_div frequency to 25MHz
as specified in "Common Module Clock Configurations" of the Cadence
Sierra 16FFC Multi-Protocol PHY PMA Specification. It is set to 25MHz
since the only user of Cadence Sierra SERDES, TI J721E SoC provides
input clock frequency of 100MHz. For other frequencies,
cmn_refclk_dig_div/cmn_refclk1_dig_div should be configured
based on the "Common Module Clock Configurations".
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Sierra SERDES IP supports upto 16 lanes (though not all of it
will be enabled in a platform). Allow Sierra driver to support a
maximum of upto 16 lanes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
A link may have multiple lanes each with a separate reset. Get
reset control "array" in order to reset all the lanes associated
with the link.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The existing configuration done in Cadence Sierra driver is only for
reference and is not used in any platforms. Remove them and configure
both lane cdb and common cdb registers to be used with external
SSC configuration. This is validated in TI J721E platform.
Signed-off-by: Anil Varughese <aniljoy@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Instead of invoking cdns_sierra_phy_init() from probe, add it in
phy_ops so that it's initialized when the PHY consumer invokes
phy_init()
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
SERDES_16G in TI's J721E SoC uses Cadence Sierra PHY. Add
support to use Cadence Sierra driver in J721E SoC.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use "regmap" for read and write to Sierra registers. This is in
perparation for adding SERDES_16G support present in TI's J721E
SoC.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Certain platforms like TI J721E using Cadence Sierra Serdes
doesn't provide explicit phy_clk and reset (APB reset) control.
Make them optional here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for 7211 USB wake. Disable all possible 7211 USB logic
for S2/S5 if USB wake is not enabled.
On the 7211, the XHCI wake signal was not connected properly and
only goes to the USB1_USB1_CTRL_TP_DIAG1 diagonstic register.
The workaround is to have VPU code running that polls for the
proper bit in the DIAG register and to wake the system when
the bit is asserted.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This is a result of the USB 2.0 clocks not being disabled/enabled
during suspend/resume on XHCI only systems.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The BDC "Read Transaction Size" needs to be changed from 1024
bytes to 256 bytes to prevent occasional transaction failures.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When there is no device connected and FSM is enabled, the XHCI puts
the PHY into suspend mode. When the PHY is put into suspend mode
the USB LDO powers down the PHY. This causes the MDIO to be
inaccessible and its registers reset to default. The fix is to
disable FSM.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Handle defer on clk_get because the new SCMI clock driver comes
up after this driver.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The 7211b0 has added the STB XHCI Synopsys controller and it
will be used instead of the RPi based DWC USB controller. The new
Synopsys XHCI controller core is the same one that is used on the
7216, but because of the way the STB USB PHY is used on both the A0
and B0, some of the PHY control is different.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The 7216 has the new USB XHCI controller from Synopsys. While
this new controller and the PHY are similar to the STB versions,
the major differences are:
- Many of the registers and fields in the CTRL block have been
removed or changed.
- A new set of Synopsys control registers, BCHP_USB_XHCI_GBL, were
added.
- MDIO functionality has been replaced with direct access registers
in the BCHP_USB_XHCI_GBL block.
- Power up PHY defaults that had to be changed by MDIO in previous
chips will now power up with the correct defaults.
A new init module was created for this new Synopsys USB controller.
A new compatible string was added and the driver will dispatch
into one of two init modules based on it. A "reg-names" field was
added so the driver can more easily get optional registers.
A DT bindings document was also added for this driver.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The driver is being restructured in preparation for adding support
for the new Synopsys USB conroller on the 7216. Since all the bugs
and work-arounds in previous STB chips are supposed to be fixed,
most of the code in phy-brcm-usb-init.c is not needed. Instead of
adding more complexity to the already complicated phy-brcm-usb-init.c
module, the driver will be restructured to use a vector table to
dispatch into different C modules for the different controllers.
There was also some general cleanup done including some ipp setup
code that was incorrect.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add the ability to handle USB wake events from USB devices when
in S2 mode. Typically there is some additional configuration
needed to tell the USB device to generate the wake event when
suspended but this varies with the different USB device classes.
For example, on USB Ethernet dongles, ethtool should be used to
enable the magic packet wake functionality in the dongle.
NOTE: This requires that the "power/wakeup" sysfs entry for
the USB device generating the wakeup be set to "enabled".
This functionality requires a special hardware sideband path that
will trigger the AON_PM_L2 interrupt needed to wake the system from
S2 even though the USB host controllers are in IDDQ (low power state)
and most USB related clocks are shut off. For the sideband signaling
to work we need to leave the usbx_freerun clock running, but this
clock consumes very little power by design. There's a bug in the
XHCI wake hardware so only EHCI/OHCI wake is currently supported.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently the Phy driver will put the USB phys into the max
power saving mode (IDDQ) when there is no corresponding XHCI, EHCI
or OHCI client (through rmmod, unbind or if the driver is not
builtin). This change will also put the Phys into IDDQ mode
on suspend so that S2 will get the additional power savings.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The BRCM USB Phy, ohci, ehci and xhci drivers all use the USB clocks
but not all drivers use the clk_prepare_enable/clk_disable_unprepare
versions to enable/disable the clocks. This change gets all drivers
using the prepare version.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When the EHCI controller received a 512 byte USB packet that
had to be broken into 2 256 byte bursts across the SCB bus AND
there was a following 512 byte USB packet, the second burst of
data from the first packet was sometimes being lost. If the
burst size was changed to 128 bytes via the EBR_SCB_SIZE field
in the USB_CTRL_EBRIDGE register we'd see the 4th 128 byte burst
of the first packet being lost. This problem became much worse
if other threads were running that accessed memory, like a memcpy
test. Setting the EBR_SCB_SIZE to 512, which prevents breaking
the EHCI USB packet (max size of 512 bytes) into bursts, fixed
the problem.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
For V4 QMP UFS Phy, we need to assert reset bits, configure the phy and
then deassert it, so add the QPHY_SW_RESET register which does this.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
SM8150 QMPY phy for UFS and onwards the PHY_SW_RESET is present in PHY's
PCS register so we should not mark no_pcs_sw_reset for sm8150 and
onwards
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We already write to QPHY_POWER_DOWN_CONTROL in qcom_qmp_phy_com_init()
before invoking qcom_qmp_phy_configure() so remove the duplicate write.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We already define register offsets so use them in register layout.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
7216 is a 16nm process chip with a slightly different version of the PHY
SerdDeS/AFE that requires a specific tuning sequence. Key on the
compatible string to perform that initialization.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
During review it came to light that exposing the pll clock outside is
not the right approach and struct phy_configure_opts_mipi_dphy exists
just for that reason to transfer parameters to the phy.
So drop the exposed clock and rely on the phy configure options
to bring in the correct rate. That way we can also just drop the
open coded timing struct and default values function.
Fixes: b7535a3bc0 ("phy/rockchip: Add support for Innosilicon MIPI/LVDS/TTL PHY")
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fixes coccicheck warning:
drivers/phy/lantiq/phy-lantiq-vrx200-pcie.c:389:2-3: Unneeded semicolon
Fixes: e52a632195 ("phy: lantiq: vrx200-pcie: add a driver for the Lantiq VRX200 PCIe PHY")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ma Feng <mafeng.ma@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Clang warns:
../drivers/phy/qualcomm/phy-qcom-apq8064-sata.c:83:4: warning:
misleading indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
usleep_range(DELAY_INTERVAL_US, DELAY_INTERVAL_US + 50);
^
../drivers/phy/qualcomm/phy-qcom-apq8064-sata.c:80:3: note: previous
statement is here
if (readl_relaxed(addr) & mask)
^
1 warning generated.
This warning occurs because there is a space after the tab on this line.
Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.
Fixes: 1de990d8a1 ("phy: qcom: Add driver for QCOM APQ8064 SATA PHY")
Link: https://github.com/ClangBuiltLinux/linux/issues/816
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In order to enforce suspend/resume ordering, this commit creates link
between phy consumers and phy devices. This link avoids to suspend phy
before phy consumers.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
[jonathanh@nvidia.com: Fix an abort when of_phy_get() returns error]
Signed-off-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Some of the phy drivers can be compile tested to increase build
coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200103164710.4829-2-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch network drivers, phy drivers, and SFP/phylink over to use the
more correct 10GBASE-R, rather than 10GBASE-KR. 10GBASE-KR is backplane
ethernet, which is 10GBASE-R with autonegotiation on top, which our
current usage on the affected platforms does not have.
The only remaining user of PHY_INTERFACE_MODE_10GKR is the Aquantia
PHY, which has a separate mode for 10GBASE-KR.
For Marvell mvpp2, we detect 10GBASE-KR, and rewrite it to 10GBASE-R
for compatibility with existing DT - this is the only network driver
at present that makes use of PHY_INTERFACE_MODE_10GKR.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 287422a95f ("drm/rockchip: Round up _before_ giving to the clock framework")
changed what rate clk_round_rate() is called with, an additional 999 Hz
added to the requsted mode clock. This has caused a regression on RK3328
and presumably also on RK3228 because the inno-hdmi-phy clock requires an
exact match of the requested rate in the pre pll config table.
When an exact match is not found the parent clock rate (24MHz) is returned
to the clk_round_rate() caller. This cause wrong pixel clock to be used and
result in no-signal when configuring a mode on RK3328.
Fix this by rounding the rate down to closest 1000 Hz in round_rate func,
this allows an exact match to be found in pre pll config table.
Fixes: 287422a95f ("drm/rockchip: Round up _before_ giving to the clock framework")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We are currently writing the same register twice. Let's enable the USB
PHY only at the end of the function.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When docked to a Motorola lapdock or media dock, we're in USB A-host mode
with VBUS provided by the dock. When in regular USB A-host mode, we're
providing the VBUS. And in regular USB A-host mode we must also keep
kicking the VBUS to keep it active.
Let's wait a bit before configuring the USB PHY to allow some time between
the ID and VBUS changes. And let's add vbus_provider flag so we can detect
docked mode and regularo USB A-host mode better.
With better USB A-host mode detection, we can now also just kick the
VBUS to keep it enabled and leave out the unnecessary line muxing.
We only need to set and clear vbus_provider in the delayed work so no
locking is needed for it currently.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The micro-USB connector on Motorola Mapphone devices can be muxed between
the SoC and the mdm6600 modem. But even when used for the SoC, configuring
the PHY with ID pin grounded will wake up the modem from idle state. Looks
like the issue is probably caused by line glitches.
We can prevent the glitches by using a previously unknown mode of the
GPIO mux to prevent the USB lines from being connected to the moden while
configuring the USB PHY, and enable the USB lines after configuring the
PHY.
Note that this only prevents waking up mdm6600 as regular USB A-host mode,
and does not help when connected to a lapdock. The lapdock specific issue
still needs to be debugged separately.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Only the used bits get cleared with bitmap_zero() when we call
gpiod_get_array_value_cansleep(). We must mask only the bits we're
using for ddata->status as the other bits in the bitmap may not be
initialized.
And let's also drop useless debug code accidentally left over while
at it.
Fixes: b9762bebc6 ("gpiolib: Pass bitmaps, not integer arrays, to get/set array")
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We must let the USB host idle things properly before we switch to debug
UART mode. Otherwise the USB host may never idle after disconnecting
devices, and that causes the next enumeration to be flakey.
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Fixes: 6d6ce40f63 ("phy: cpcap-usb: Add CPCAP PMIC USB support")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
It's typical for the QHP PHY to take slightly above 1ms to initialize,
so increase the timeout of the PHY ready check to 10ms - as already done
in the downstream PCIe driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Evan Green <evgreen@chromium.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The driver calls clk_prepare_enable in probe but the corresponding
clk_disable_unprepare() is in ti_pipe3_disable_clocks().
Move clk_disable_unprepare() to remove to make them symmetric.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch corrects the SPDX License Identifier style in
header files related to PHY drivers for Qualcomm platforms.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
If musb_mailbox() returns an error, we must still continue to finish
configuring the phy.
Otherwise the phy state may end up only half initialized, and this can
cause the debug serial console to stop working. And this will happen if the
usb driver musb controller is not loaded.
Let's fix the issue by adding helper for cpcap_usb_try_musb_mailbox().
Fixes: 6d6ce40f63 ("phy: cpcap-usb: Add CPCAP PMIC USB support")
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo
-----BEGIN PGP SIGNATURE-----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=dk7w
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Olof Johansson:
"Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
soc: fsl: add RCPM driver
dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
memory: tegra: Consolidate registers definition into common header
memory: tegra: Ensure timing control debug features are disabled
memory: tegra: Introduce Tegra30 EMC driver
memory: tegra: Do not handle error from wait_for_completion_timeout()
memory: tegra: Increase handshake timeout on Tegra20
memory: tegra: Print a brief info message about EMC timings
memory: tegra: Pre-configure debug register on Tegra20
memory: tegra: Include io.h instead of iopoll.h
memory: tegra: Adapt for Tegra20 clock driver changes
memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
memory: tegra: Add gr2d and gr3d to DRM IOMMU group
memory: tegra: Set DMA mask based on supported address bits
soc: at91: Add Atmel SFR SN (Serial Number) support
memory: atmel-ebi: switch to SPDX license identifiers
memory: atmel-ebi: move NUM_CS definition inside EBI driver
soc: mediatek: Refactor bus protection control
soc: mediatek: Refactor sram control
...
-----BEGIN PGP SIGNATURE-----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=uUXw
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Warn if a host bridge has no NUMA info (Yunsheng Lin)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis
Efremov)
Resource management:
- Fix boot-time Embedded Controller GPE storm caused by incorrect
resource assignment after ACPI Bus Check Notification (Mika
Westerberg)
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control
the MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA
devices downstream (Subbaraya Sundeep)
- Consolidate DT "dma-ranges" parsing and convert all host drivers to
use shared parsing (Rob Herring)
Error reporting:
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC
even if platform didn't grant control over AER (Olof Johansson)
Hotplug:
- Avoid returning prematurely from sysfs requests to enable or
disable a PCIe hotplug slot (Lukas Wunner)
- Don't disable interrupts twice when suspending hotplug ports (Mika
Westerberg)
- Fix deadlocks when PCIe ports are hot-removed while suspended (Mika
Westerberg)
Power management:
- Remove unnecessary ASPM locking (Bjorn Helgaas)
- Add support for disabling L1 PM Substates (Heiner Kallweit)
- Allow re-enabling Clock PM after it has been disabled (Heiner
Kallweit)
- Add sysfs attributes for controlling ASPM link states (Heiner
Kallweit)
- Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl"
sysfs files (Heiner Kallweit)
- Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on
USB 2.0 or 1.1 connect events (Kai-Heng Feng)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk
for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we
only did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn
Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0)
instead of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
Virtualization:
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn
Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the
VFs, but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and
associated VFs can be enabled independently (Kuppuswamy
Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof
Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn
Helgaas)
- Hide PRI and PASID state restoration functions used only inside the
PCI core (Bjorn Helgaas)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George
Cherian)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Unify ACS quirk implementations (Bjorn Helgaas)
Amlogic Meson host bridge driver:
- Fix meson PERST# GPIO polarity problem (Remi Pommarel)
- Add DT bindings for Amlogic Meson G12A (Neil Armstrong)
- Fix meson clock names to match DT bindings (Neil Armstrong)
- Add meson support for Amlogic G12A SoC with separate shared PHY
(Neil Armstrong)
- Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe
combo PHY (Neil Armstrong)
- Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)
- Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT
(Neil Armstrong)
Broadcom iProc host bridge driver:
- Invalidate iProc PAXB address mapping before programming it
(Abhishek Shah)
- Fix iproc-msi and mvebu __iomem annotations (Ben Dooks)
Cadence host bridge driver:
- Refactor Cadence PCIe host controller to use as a library for both
host and endpoint (Tom Joseph)
Freescale Layerscape host bridge driver:
- Add layerscape LS1028a support (Xiaowei Bao)
Intel VMD host bridge driver:
- Add VMD bus 224-255 restriction decode (Jon Derrick)
- Add VMD 8086:9A0B device ID (Jon Derrick)
- Remove Keith from VMD maintainer list (Keith Busch)
Marvell ARMADA 3700 / Aardvark host bridge driver:
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted
before the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi
Pommarel)
- Don't rely on jiffies in Aardvark config access path since
interrupts may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
Marvell ARMADA 370 / XP host bridge driver:
- Make mvebu_pci_bridge_emul_ops static (Ben Dooks)
Microsoft Hyper-V host bridge driver:
- Add hibernation support for Hyper-V virtual PCI devices (Dexuan
Cui)
- Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan
Cui)
- Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui)
Mobiveil host bridge driver:
- Change mobiveil csr_read()/write() function names that conflict
with riscv arch functions (Kefeng Wang)
NVIDIA Tegra host bridge driver:
- Fix Tegra CLKREQ dependency programming (Vidya Sagar)
Renesas R-Car host bridge driver:
- Remove unnecessary header include from rcar (Andrew Murray)
- Tighten register index checking for rcar inbound range programming
(Marek Vasut)
- Fix rcar inbound range alignment calculation to improve packing of
multiple entries (Marek Vasut)
- Update rcar MACCTLR setting to match documentation (Yoshihiro
Shimoda)
- Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual
(Yoshihiro Shimoda)
- Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon
Horman)
Rockchip host bridge driver:
- Make rockchip 0V9 and 1V8 power regulators non-optional (Robin
Murphy)
Socionext UniPhier host bridge driver:
- Set uniphier to host (RC) mode always (Kunihiko Hayashi)
Endpoint drivers:
- Fix endpoint driver sign extension problem when shifting page
number to phys_addr_t (Alan Mikhak)
Misc:
- Add NumaChip SPDX header (Krzysztof Wilczynski)
- Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski)
- Remove unused includes (Krzysztof Wilczynski)
- Removed unused sysfs attribute groups (Ben Dooks)
- Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas)
- Add PCIe Link Control 2 register field definitions to replace magic
numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas)
- Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and
Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas)
- Use pcie_capability_read_word() instead of pci_read_config_word()
in AMDGPU and Radeon CIK/SI (Frederick Lawler)
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
- Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe)
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
- Fix dwc find_next_bit() usage (Niklas Cassel)
- Fix pcitest.c fd leak (Hewenliang)
- Fix typos and comments (Bjorn Helgaas)
- Fix Kconfig whitespace errors (Krzysztof Kozlowski)"
* tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits)
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer
PCI: hv: Change pci_protocol_version to per-hbus
PCI: hv: Add hibernation support
PCI: hv: Reorganize the code in preparation of hibernation
MAINTAINERS: Remove Keith from VMD maintainer
PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code
PCI/ASPM: Add sysfs attributes for controlling ASPM link states
PCI: Fix indentation
drm/radeon: Prefer pcie_capability_read_word()
drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions
drm/radeon: Correct Transmit Margin masks
drm/amdgpu: Prefer pcie_capability_read_word()
PCI: uniphier: Set mode register to host mode
drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions
...
Here is the big set of char/misc and other driver patches for 5.5-rc1
Loads of different things in here, this feels like the catch-all of
driver subsystems these days. Full details are in the shortlog, but
nothing major overall, just lots of driver updates and additions.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd6ewA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymNXACfebVkDrFOH9EqDgFArPvZ1i9EmZ4AoLbE1Wki
ftJApk+Ov1BT2TvClOza
=cXqg
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc and other driver patches for 5.5-rc1
Loads of different things in here, this feels like the catch-all of
driver subsystems these days. Full details are in the shortlog, but
nothing major overall, just lots of driver updates and additions.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (198 commits)
char: Fix Kconfig indentation, continued
habanalabs: add more protection of device during reset
habanalabs: flush EQ workers in hard reset
habanalabs: make the reset code more consistent
habanalabs: expose reset counters via existing INFO IOCTL
habanalabs: make code more concise
habanalabs: use defines for F/W files
habanalabs: remove prints on successful device initialization
habanalabs: remove unnecessary checks
habanalabs: invalidate MMU cache only once
habanalabs: skip VA block list update in reset flow
habanalabs: optimize MMU unmap
habanalabs: prevent read/write from/to the device during hard reset
habanalabs: split MMU properties to PCI/DRAM
habanalabs: re-factor MMU masks and documentation
habanalabs: type specific MMU cache invalidation
habanalabs: re-factor memory module code
habanalabs: export uapi defines to user-space
habanalabs: don't print error when queues are full
habanalabs: increase max jobs number to 512
...
Here is the big set of USB patches for 5.5-rc1
Lots of little things in here:
- typec updates and additions
- usb-serial drivers cleanups and fixes
- misc USB drivers cleanups and fixes
- gadget drivers new features and controllers added
- usual xhci additions
- other minor changes
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd5+Iw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylA4wCbB3P206oHeHLBe9Eika3D8gM9/fMAn2oWlmpB
Xh7wr30FGC02zU/KBpJ1
=U5qC
-----END PGP SIGNATURE-----
Merge tag 'usb-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big set of USB patches for 5.5-rc1
Lots of little things in here:
- typec updates and additions
- usb-serial drivers cleanups and fixes
- misc USB drivers cleanups and fixes
- gadget drivers new features and controllers added
- usual xhci additions
- other minor changes
All of these have been in linux-next with no reported issues"
* tag 'usb-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (223 commits)
usb: gadget: udc: gr_udc: create debugfs directory under usb root
usb: gadget: atmel: create debugfs directory under usb root
usb: musb: create debugfs directory under usb root
usb: serial: Fix Kconfig indentation
usb: misc: Fix Kconfig indentation
usb: gadget: Fix Kconfig indentation
usb: host: Fix Kconfig indentation
usb: dwc3: Fix Kconfig indentation
usb: gadget: configfs: Fix missing spin_lock_init()
usb-storage: Disable UAS on JMicron SATA enclosure
USB: documentation: flags on usb-storage versus UAS
USB: uas: heed CAPACITY_HEURISTICS
USB: uas: honor flag to avoid CAPACITY16
usb: host: xhci-tegra: Correct phy enable sequence
usb-serial: cp201x: support Mark-10 digital force gauge
usb: chipidea: imx: pinctrl for HSIC is optional
usb: chipidea: imx: refine the error handling for hsic
usb: chipidea: imx: change hsic power regulator as optional
usb: chipidea: imx: check data->usbmisc_data against NULL before access
usb: chipidea: core: change vbus-regulator as optional
...
Add dependency from TI_CPSW_SWITCHDEV.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The px30 soc from Rockchip shares the same register description as
the rk3328, so can re-use its definitions.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Commit f0b5c2c963 ("phy: qcom-usb-hs: Replace the extcon API")
switched from extcon_register_notifier() to the resource-managed
API, i.e. devm_extcon_register_notifier().
This is problematic in this case, because the extcon notifier
is dynamically registered/unregistered whenever the PHY is powered
on/off. The resource-managed API does not unregister the notifier
until the driver is removed, so as soon as the PHY is power cycled,
attempting to register the notifier again results in:
double register detected
WARNING: CPU: 1 PID: 182 at kernel/notifier.c:26 notifier_chain_register+0x74/0xa0
Call trace:
...
extcon_register_notifier+0x74/0xb8
devm_extcon_register_notifier+0x54/0xb8
qcom_usb_hs_phy_power_on+0x1fc/0x208
...
... and USB stops working after plugging the cable out and in
another time.
The easiest way to fix this is to make a partial revert of
commit f0b5c2c963 ("phy: qcom-usb-hs: Replace the extcon API")
and avoid using the resource-managed API in this case.
Fixes: f0b5c2c963 ("phy: qcom-usb-hs: Replace the extcon API")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix the below smatch warning by adding variable check rather than the
hardcoded value.
warn: array off by one? 'data->select_value[channel_num]'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: e52a632195 ("phy: lantiq: vrx200-pcie: add a driver for the Lantiq VRX200 PCIe PHY")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Innosilicon Video Combo PHY not only supports MIPI DSI,
but also LVDS and TTL functions with small die size and low
pin count. Customers can choose according to their own applications.
Signed-off-by: Wyon Bi <bivvy.bi@rock-chips.com>
[removed TTL mode for now, as it required a hook back into the dsi host]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Allwinner H6 SoC contains a USB3 PHY (with USB2 DP/DM lines also
controlled).
Add a driver for it.
The register operations in this driver is mainly extracted from the BSP
USB3 driver.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
SM8150 UFS PHY is v4 of QMP phy. Add support for V4 QMP phy register
defines and support for SM8150 QMP UFS PHY.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Now phy-gmii-sel will disable MAC TX internal delay for PHY interface mode
"rgmii-rxid" which is incorrect.
Hence, fix it by enabling MAC TX internal delay in the case of "rgmii-rxid"
mode.
Fixes: 92b58b3474 ("phy: ti: introduce phy-gmii-sel driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use the new regulator helper instead of a for loop.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/phy/ti/phy-dm816x-usb.c:192:29: warning:
variable phy_data set but not used [-Wunused-but-set-variable]
It is never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Since the role_store() uses strncmp(), it's possible to refer
out-of-memory if the sysfs data size is smaller than strlen("host").
This patch fixes it by using sysfs_streq() instead of strncmp().
Reported-by: Pavel Machek <pavel@denx.de>
Fixes: 9bb86777fb ("phy: rcar-gen3-usb2: add sysfs for usb role swap")
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tegra XUSB device control driver needs to control vbus override
during its operations, add API for the support.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tegra XUSB device control driver needs to control vbus override
during its operations, add API for the support.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
On Tegra210, usb2 only otg/peripheral ports dont work in device mode.
They need an assosciated usb3 port to work in device mode. Identify
an unused usb3 port and assign it as a fake USB3 port to USB2 only
port whose mode is otg/peripheral.
Based on work by BH Hsieh <bhsieh@nvidia.com>.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Configure the port capabilities based on usb_dr_mode settings.
Based on work by JC Kuo <jckuo@nvidia.com>.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The xhci_ec_base variable is a pointer, so don't compare
it with an integer.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
As platform_get_irq() now prints an error when the interrupt does not
exist, a scary warning may be printed for an optional interrupt:
phy_rcar_gen3_usb2 ee0a0200.usb-phy: IRQ index 0 not found
Fix this by calling platform_get_irq_optional() instead.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The local variable @priv is set but not used, can be removed
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Don't populate the array serdes_reg on the stack but instead make it
static const. Makes the object code smaller by 228 bytes.
Before:
text data bss dec hex filename
23875 6232 64 30171 75db drivers/phy/phy-xgene.o
After:
text data bss dec hex filename
23551 6328 64 29943 74f7 drivers/phy/phy-xgene.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
As platform_get_irq() now prints an error when the interrupt does not
exist, a scary warning may be printed for an optional interrupt:
phy_rcar_gen3_usb2 ee0a0200.usb-phy: IRQ index 0 not found
Fix this by calling platform_get_irq_optional() instead.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add PHY driver for the USB2 PHY found on Marvell MMP3 SoC.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds extended PCIe PHY functions for the Amlogic G12A
USB3+PCIE Combo PHY to support reset, power_on and power_off for
PCIe exclusively.
With these callbacks, we can handle all the needed operations of the
Amlogic PCIe controller driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Core:
* Ensure HWMON devices are registered with valid names
* Fix device wakeup code
Drivers:
* bq25890_charger: Add BQ25895 support
* axp288_fuel_gauge: Add Minix Neo Z83-4 to blacklist
* sc27xx: improve battery calibration
* misc. small fixes all over drivers
-----BEGIN PGP SIGNATURE-----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=cIXy
-----END PGP SIGNATURE-----
Merge tag 'for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Core:
- Ensure HWMON devices are registered with valid names
- Fix device wakeup code
Drivers:
- bq25890_charger: Add BQ25895 support
- axp288_fuel_gauge: Add Minix Neo Z83-4 to blacklist
- sc27xx: improve battery calibration
- misc small fixes all over drivers"
* tag 'for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (24 commits)
power: supply: cpcap-charger: Enable vbus boost voltage
power: supply: sc27xx: Add POWER_SUPPLY_PROP_CALIBRATE attribute
power: supply: sc27xx: Optimize the battery capacity calibration
power: supply: sc27xx: Make sure the alarm capacity is larger than 0
power: supply: sc27xx: Fix the the accuracy issue of coulomb calculation
power: supply: sc27xx: Fix conditon to enable the FGU interrupt
power: supply: sc27xx: Add POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN attribute
power: supply: max77650: add MODULE_ALIAS()
power: supply: isp1704: remove redundant assignment to variable ret
power: supply: bq25890_charger: Add the BQ25895 part
power: supply: sc27xx: Replace devm_add_action() followed by failure action with devm_add_action_or_reset()
power: supply: sc27xx: Introduce local variable 'struct device *dev'
power: reset: reboot-mode: Fix author email format
power: supply: ab8500: remove set but not used variables 'vbup33_vrtcn' and 'bup_vch_range'
power: supply: max17042_battery: Fix a typo in function names
power: reset: gpio-restart: Fix typo when gpio reset is not found
power: supply: Init device wakeup after device_add()
power: supply: ab8500_charger: Mark expected switch fall-through
power: supply: sbs-battery: only return health when battery present
MAINTAINERS: N900: Remove isp1704_charger.h record
...
clk registration by clk providers and debugfs "nice to haves" for rate
constraints. I'll highlight that we're now setting the clk_init_data pointer
inside struct clk_hw to NULL during clk_register(), which may break some
drivers that thought they could use that pointer during normal operations. That
change has been sitting in next for a while now but maybe something is still
broken. We'l see. Other than that the core framework changes aren't invasive
and they're fixing bugs, simplifying, and making things better.
On the clk driver side we got the usual addition of new SoC support, new
features for existing drivers, and bug fixes scattered throughout. The biggest
diffstat is the Amlogic driver that gained CPU clk support in addition to
migrating to the new way of specifying clk parents. After that the Qualcomm,
i.MX, Mediatek, and Rockchip clk drivers got support for various new SoCs and
clock controllers from those vendors.
Core:
- Drop NULL checks in clk debugfs
- Add min/max rates to clk debugfs
- Set clk_init_data pointer inside clk_hw to NULL after registration
- Make clk_bulk_get_all() return an 'id' corresponding to clock-names
- Evict parents from parent cache when they're unregistered
New Drivers:
- Add clock driver for i.MX8MN SoCs
- Support aspeed AST2600 SoCs
- Support for Mediatek MT6779 SoCs
- Support qcom SM8150 GCC and RPMh clks
- Support qcom QCS404 WCSS clks
- Add CPU clock support for Armada 7K/8K (specifically AP806 and AP807)
- Addition of clock driver for Rockchip rk3308 SoCs
Updates:
- Add regulator support to the cdce925 clk driver
- Add support for Raspberry Pi 4 bcm2711 SoCs
- Add SDIO gate support to aspeed driver
- Add missing of_node_put() calls in various clk drivers
- Migrate Amlogic driver to new clock parent description method
- Add DVFS support to Amlogic Meson g12
- Add Amlogic Meson g12a reset support to the axg audio clock controller
- Add sm1 support to the Amlogic Meson g12a clock controller
- Switch i.MX8MM clock driver to platform driver
- Add Hifi4 DSP related clocks for i.MX8QXP SoC
- Fix Audio PLL setting and parent clock for USB
- Misc i.MX8 clock driver improvements and corrections
- Set floor ops for Qualcomm SD clks so that rounding works
- Fix "always-on" Clock Domains on Renesas R-Car M1A, RZ/A1, RZ/A2, and RZ/N1
- Enable the Allwinner V3 SoC and fix the i2s clock for H6
-----BEGIN PGP SIGNATURE-----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=z8wK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have a small collection of core framework updates this time, mostly
around clk registration by clk providers and debugfs "nice to haves"
for rate constraints. I'll highlight that we're now setting the
clk_init_data pointer inside struct clk_hw to NULL during
clk_register(), which may break some drivers that thought they could
use that pointer during normal operations. That change has been
sitting in next for a while now but maybe something is still broken.
We'l see. Other than that the core framework changes aren't invasive
and they're fixing bugs, simplifying, and making things better.
On the clk driver side we got the usual addition of new SoC support,
new features for existing drivers, and bug fixes scattered throughout.
The biggest diffstat is the Amlogic driver that gained CPU clk support
in addition to migrating to the new way of specifying clk parents.
After that the Qualcomm, i.MX, Mediatek, and Rockchip clk drivers got
support for various new SoCs and clock controllers from those vendors.
Core:
- Drop NULL checks in clk debugfs
- Add min/max rates to clk debugfs
- Set clk_init_data pointer inside clk_hw to NULL after registration
- Make clk_bulk_get_all() return an 'id' corresponding to clock-names
- Evict parents from parent cache when they're unregistered
New Drivers:
- Add clock driver for i.MX8MN SoCs
- Support aspeed AST2600 SoCs
- Support for Mediatek MT6779 SoCs
- Support qcom SM8150 GCC and RPMh clks
- Support qcom QCS404 WCSS clks
- Add CPU clock support for Armada 7K/8K (specifically AP806 and AP807)
- Addition of clock driver for Rockchip rk3308 SoCs
Updates:
- Add regulator support to the cdce925 clk driver
- Add support for Raspberry Pi 4 bcm2711 SoCs
- Add SDIO gate support to aspeed driver
- Add missing of_node_put() calls in various clk drivers
- Migrate Amlogic driver to new clock parent description method
- Add DVFS support to Amlogic Meson g12
- Add Amlogic Meson g12a reset support to the axg audio clock controller
- Add sm1 support to the Amlogic Meson g12a clock controller
- Switch i.MX8MM clock driver to platform driver
- Add Hifi4 DSP related clocks for i.MX8QXP SoC
- Fix Audio PLL setting and parent clock for USB
- Misc i.MX8 clock driver improvements and corrections
- Set floor ops for Qualcomm SD clks so that rounding works
- Fix "always-on" Clock Domains on Renesas R-Car M1A, RZ/A1, RZ/A2, and RZ/N1
- Enable the Allwinner V3 SoC and fix the i2s clock for H6"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits)
clk: Drop !clk checks in debugfs dumping
clk: imx: imx8mn: fix pll mux bit
clk: imx: imx8mm: fix pll mux bit
clk: imx: clk-pll14xx: unbypass PLL by default
clk: imx: pll14xx: avoid glitch when set rate
clk: mvebu: ap80x: add AP807 clock support
clk: mvebu: ap806: Prepare the introduction of AP807 clock support
clk: mvebu: ap806: add AP-DCLK (hclk) to system controller driver
clk: mvebu: ap806: be more explicit on what SaR is
clk: mvebu: ap80x-cpu: add AP807 CPU clock support
clk: mvebu: ap806-cpu: prepare mapping of AP807 CPU clock
dt-bindings: ap806: Document AP807 clock compatible
dt-bindings: ap80x: Document AP807 CPU clock compatible
clk: sprd: add missing kfree
clk: at91: allow 24 Mhz clock as input for PLL
clk: Make clk_bulk_get_all() return a valid "id"
clk: actions: Fix factor clk struct member access
clk: qcom: rcg: Return failure for RCG update
clk: remove extra ---help--- tags in Kconfig
clk: add include guard to clk-conf.h
...
We are currently not enabling VBUS boost for cpcap when in host mode.
This means the VBUS is fed at the battery voltage level, which can cause
flakeyness enumerating devices.
Looks like the boost control for VBUS is CPCAP_BIT_VBUS_SWITCH that we
must enable in the charger for nice 4.92 V VBUS output. And looks like
we must not use the STBY pin enabling but must instead use manual VBUS
control in phy-cpcap-usb.
We want to do this in cpcap_charger_vbus_work() and also set a flag for
feeding_vbus to avoid races between USB detection and charger detection,
and disable charging if feeding_vbus is set.
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The documentation for Marvell's cp110 phy refers to these
registers/register regions as DTL control, DTL frequency loop enable,
etc. This patch aligns the relevant code for these accordingly.
Signed-off-by: Matt Pelland <mpelland@starry.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Marvell's cp110 phy supports RXAUI on lanes 2, 3, 4, and 5 when
connected to port zero. When used in this mode, lanes operate in pairs
of two (2 and 3, 4 and 5).
Signed-off-by: Matt Pelland <mpelland@starry.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Now that all COMPHY modes are supported by the driver, update the
comment stating that mvebu_comphy_power_off() should be called for
each lane. This is still wrong because for compatibility reasons, it
might break users running an old firmware (the driver only uses SMC
calls for SATA, USB and PCIe configuration, there is no code in Linux
to fallback on in these cases.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add PCIe support by filling the COMPHY modes table.
Also add a new macro to generate the right value for the firmware
depending on the width (PCI x1, x2, x4, etc). The width will be passed
by the core as the "submode" argument of the ->set_mode() callback. If
this argument is zero, default to x1 mode.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Before adding more logic, simplify a bit the writing of the
mvebu_comphy_get_mode() helper by using a pointer instead of
referencing a configuration with the entire table name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add the corresponding entries in the COMPHY modes table.
SATA support does not need any additional care.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add USB3 host/device support by adding the right entries in the COMPHY
modes table. A new macro is created to instantiate a "generic" mode
ie. not an Ethernet one. This macro will be re-used when adding SATA
support.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The COMPHY can configure the SERDES lanes in several non-Ethernet
modes: SATA, USB3, PCIe. Drop the condition limiting the driver to
Ethernet modes only before adding support for more.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Before adding support for other PHY modes (not Ethernet ones), let's
rename the MVEBU_COMPHY_CONF macro to a more specific (and shorter)
appellation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for RXAUI mode by adding an entry in the COMPHY modes list.
There is no user for this mode yet so we can enforce an up-to-date
firmware and return an error otherwise without breaking anywone.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently, the driver supports setting lanes to 1000BASEX, 2500BASEX,
10GKR. Complete the COMPHY modes list by adding two (already
supported) cases for lane 4.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Keep the exact same list of supported configurations but first try to
use the firmware's implementation. If it fails, try the legacy method:
Linux implementation.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Explicitly set the lane submode (enum) to a known invalid value.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There is no public clock tree that implies such dependencies between
the MG/MG-core/AXI clocks and the COMPHY IP but accessing the COMPHY
registers while one of the three clocks are disabled stalls the CPU.
This happens if, for instance, the COMPHY driver probe is deferred
(eg. the USB Vbus regulator driver is not yet visible). The MVPP2
driver which also needs these clocks (among others) will
prepare/enable the clocks, then be deferred, and disable/unprepare
them. Next COMPHY lane to be configured would produce an infinite
stall.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
After commit "linux/bits.h: Add compile time sanity check of GENMASK
inputs" [1], arm64 defconfig builds started failing:
In file included from ../include/linux/bits.h:22,
from ../include/linux/bitops.h:5,
from ../include/linux/kernel.h:12,
from ../include/linux/clk.h:13,
from ../drivers/phy/rockchip/phy-rockchip-inno-hdmi.c:9:
../drivers/phy/rockchip/phy-rockchip-inno-hdmi.c: In function 'inno_hdmi_phy_rk3328_power_on':
../include/linux/build_bug.h:16:45: error: negative width in bit-field '<anonymous>'
16 | #define BUILD_BUG_ON_ZERO(e) (sizeof(struct { int:(-!!(e)); }))
| ^
../include/linux/bits.h:24:18: note: in expansion of macro 'BUILD_BUG_ON_ZERO'
24 | ((unsigned long)BUILD_BUG_ON_ZERO(__builtin_choose_expr( \
| ^~~~~~~~~~~~~~~~~
../include/linux/bits.h:39:3: note: in expansion of macro 'GENMASK_INPUT_CHECK'
39 | (GENMASK_INPUT_CHECK(high, low) + __GENMASK(high, low))
| ^~~~~~~~~~~~~~~~~~~
../drivers/phy/rockchip/phy-rockchip-inno-hdmi.c:24:42: note: in expansion of macro 'GENMASK'
24 | #define UPDATE(x, h, l) (((x) << (l)) & GENMASK((h), (l)))
| ^~~~~~~
../drivers/phy/rockchip/phy-rockchip-inno-hdmi.c:201:50: note: in expansion of macro 'UPDATE'
201 | #define RK3328_TERM_RESISTOR_CALIB_SPEED_7_0(x) UPDATE(x, 7, 9)
| ^~~~~~
../drivers/phy/rockchip/phy-rockchip-inno-hdmi.c:1046:26: note: in expansion of macro 'RK3328_TERM_RESISTOR_CALIB_SPEED_7_0'
1046 | inno_write(inno, 0xc6, RK3328_TERM_RESISTOR_CALIB_SPEED_7_0(v));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
As pointed out by Robin and Guenter, inno_write's val argument is an
8-bit value so having a mask larger than that doesn't make sense. This
also matches the rest of the *_7_0 macros in this driver.
[1]: https://lore.kernel.org/lkml/20190801230358.4193-2-rikard.falkeborn@gmail.com/
Reported-by: Andrzej Hajda <a.hajda@samsung.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: kernelci.org bot <bot@kernelci.org>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Despite extensive testing of commit 885bd76596 ("phy: qcom-qmp: Correct
READY_STATUS poll break condition") I failed to conclude that the
PHYSTATUS bit of the PCS_STATUS register used in PCIe and USB3 falls as
the PHY gets ready. Similar to the prior bug with UFS the code will
generally get past the check before the transition and thereby
"succeed".
Correct the name of the register used PCIe and USB3 PHYs, replace
mask_pcs_ready with a constant expression depending on the type of the
PHY and check for the appropriate ready state.
Cc: stable@vger.kernel.org
Cc: Vivek Gautam <vivek.gautam@codeaurora.org>
Cc: Evan Green <evgreen@chromium.org>
Cc: Niklas Cassel <niklas.cassel@linaro.org>
Reported-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Fixes: 885bd76596 ("phy: qcom-qmp: Correct READY_STATUS poll break condition")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Each iteration of for_each_available_child_of_node() puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence create a new label,
err_node_put, that puts the previous node (child) before returning the
required value. Also include the statement pm_runtime_disable() under
this label in order to avoid repetition among mid-loop return
conditions. Edit the mid-loop return statements to instead go to this
new label err_node_put.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The hardware manual should be revised, but the initial value of
VBCTRL.OCCLREN is set to 1 actually. If the bit is set, the hardware
clears VBCTRL.VBOUT and ADPCTRL.DRVVBUS registers automatically
when the hardware detects over-current signal from a USB power switch.
However, since the hardware doesn't have any registers which
indicates over-current, the driver cannot handle it at all. So, if
"is_otg_channel" hardware detects over-current, since ADPCTRL.DRVVBUS
register is cleared automatically, the channel cannot be used after
that.
To resolve this behavior, this patch sets the VBCTRL.OCCLREN to 0
to keep ADPCTRL.DRVVBUS even if the "is_otg_channel" hardware
detects over-current. (We assume a USB power switch itself protects
over-current and turns the VBUS off.)
This patch is inspired by a BSP patch from Kazuya Mizuguchi.
Fixes: 1114e2d317 ("phy: rcar-gen3-usb2: change the mode to OTG on the combined channel")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The regmap_node variable is still being used in the syscon_node_to_regmap()
call after the of_node_put() call, which may result in use-after-free.
Fixes: 71e2f5c5c2 ("phy: ti: Add a new SERDES driver for TI's AM654x SoC")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PHY configuration has been implemented in the firmware and accessed
through SMC calls. In the past, it worked magically if the bootloader
was correctly doing the initializations.
With up-to-date bindings, the kernel will need a recent firmware in
order to do the initializations himself (we assume people must update
their firmware along with their kernel).
People might not understand why IPs that were working correctly before
stopped to be probed suddendly. In this case, let's advise the users
to update their firmware with a visual warning.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Samsung PHY drivers control the power to the SoC core components needed by
their client devices (USB HCDs, SATA, camera ISP bridge, DP encoder) to
properly operate. Disabling PHYs in runtime usually causes the client
device to crash with external abort exception or similar issue due to lack
of API to notify clients about PHY removal. This patch removes the
possiblity to unbind Samsung Exynos PHY drivers in runtime.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Commit 36914111e6 ("drivers: phy: add calibrate method") added support
for generic phy_calibrate() method, but it didn't explain in detail when
such method is supposed to be called. Add some more documentation directly
to the phy.h to make it clean that it is intended to be called after every
host controller reset.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
return in two places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
return in two places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Unconditionally include the lantiq subdirectory in the phy Makefile.
All drivers in there have their dependencies maintained. One of these
(optional) dependencies is COMPILE_TEST, however this can only be
evaluated when Kconfig scans the lantiq subdirectory.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Lantiq VRX200 SoCs embed a PCIe PHY in the "sram" bus. Unlike most
other IP blocks on this SoC the register values are only 16-bit wide.
Like other IP blocks on this SoC the register values are in big endian.
The PHY embeds a PLL which can be configured in various modes. Only the
36MHz mode is supported for now, the other modes can be implemented when
there's a board which actually needs them. OpenWrt uses the out-of-tree
vendor driver and all supported boards there only need the 36MHz mode.
There are two input clocks:
- the "pdi" clock enables the register access
- the "phy" clock is the clock input and enables the internal PLL
There are two reset lines:
- "phy" resets the PHY itself
- the "pcie" reset line is shared between the PHY and the PCIe
controller
While the VRX200 SoC has only one PCIe controller and PHY the ARX300
uses two identical PCIe controllers and PHYs which are compatible with
the PCIe controller and PHY on VRX200.
Add a driver for this PHY so PCIe support can be enabled on these SoCs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
A future patch is going to change semantics of clk_register() so that
clk_hw::init is guaranteed to be NULL after a clk is registered. Avoid
referencing this member here so that we don't run into NULL pointer
exceptions.
Cc: Roger Quadros <rogerq@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190731193517.237136-9-sboyd@kernel.org
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Synopsys DesignWare core based PCIe controllers in Tegra 194 SoC
interface with Universal PHY (UPHY) module through a PIPE2UPHY (P2U)
module. For each PCIe lane of a controller, there is a P2U unit
instantiated at hardware level. This driver provides support for the
programming required for each P2U that is going to be used for a PCIe
controller.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Thierry Reding <treding@nvidia.com>
*) Add a new PHY driver for Qualcomm PCIe2 PHY
*) Add a new PHY driver for Mixel DPHY present in i.MX8
*) Fix Qualcomm QMP UFS PHY driver from incorrectly reporting that
PHY enable failed
*) Fix _BUG_ on Amlogic G12A USB3 + PCIE Combo PHY Driver due to
calling a sleeping function from invalid context
*) Fix WARN_ON dump on rcar-gen3-usb2 PHY driver caused due to
imbalance powered flag
*) Fix .cocci and sparse warnings
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=5mPE
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
phy: for 5.3
*) Add a new PHY driver for Qualcomm PCIe2 PHY
*) Add a new PHY driver for Mixel DPHY present in i.MX8
*) Fix Qualcomm QMP UFS PHY driver from incorrectly reporting that
PHY enable failed
*) Fix _BUG_ on Amlogic G12A USB3 + PCIE Combo PHY Driver due to
calling a sleeping function from invalid context
*) Fix WARN_ON dump on rcar-gen3-usb2 PHY driver caused due to
imbalance powered flag
*) Fix .cocci and sparse warnings
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
phy: qcom-qmp: Raise qcom_qmp_phy_enable() polling delay
phy: meson-g12a-usb3-pcie: disable locking for cr_regmap
phy: Add driver for mixel mipi dphy found on NXP's i.MX8 SoCs
dt-bindings: phy: Add documentation for mixel dphy
dt-bindings: phy-pxa-usb: add bindings
phy: renesas: rcar-gen3-usb2: fix imbalance powered flag
phy: qcom-qmp: Drop useless msm8998_pciephy_cfg setting
phy: qcom-qmp: Correct READY_STATUS poll break condition
phy: ti: am654-serdes: Make serdes_am654_xlate() static
phy: usb: phy-brcm-usb: Fix platform_no_drv_owner.cocci warnings
phy: samsung: Use struct_size() in devm_kzalloc()
phy: qcom: Add Qualcomm PCIe2 PHY driver
dt-bindings: phy: Add binding for Qualcomm PCIe2 PHY
*) Move Tegra124 PLL power supplies to be enabled by xusb-tegra124
*) Move Tegra210 PLL power supplies to be enabled by xusb-tegra210
*) Minor fixes: fix memory leaks at error path and addresses coverity.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=+dGx
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.2-rc_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 5.2-rc
*) Move Tegra124 PLL power supplies to be enabled by xusb-tegra124
*) Move Tegra210 PLL power supplies to be enabled by xusb-tegra210
*) Minor fixes: fix memory leaks at error path and addresses coverity.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.2-rc_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
phy: tegra: xusb: Add Tegra210 PLL power supplies
phy: tegra: xusb: Add Tegra124 PLL power supplies
dt-bindings: phy: tegra-xusb: List PLL power supplies
phy: usb: phy-brcm-usb: Remove sysfs attributes upon driver removal
phy: renesas: rcar-gen2: Fix memory leak at error paths
phy: qcom-qusb2: fix missing assignment of ret when calling clk_prepare_enable
readl_poll_timeout() calls usleep_range() to sleep between reads.
usleep_range() doesn't work efficiently for tiny values.
Raise the polling delay in qcom_qmp_phy_enable() to bring it in line
with the delay in qcom_qmp_phy_com_init().
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Locking is not needed for the phy_g12a_usb3_pcie_cr_bus_read/write() and
currently it causes the following BUG because of the usage of the
regmap_read_poll_timeout() running in spinlock_irq, configured by regmap fast_io.
Simply disable locking in the cr_regmap config since it's only used from the
PHY init callback function.
BUG: sleeping function called from invalid context at drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c:85
in_atomic(): 1, irqs_disabled(): 128, pid: 60, name: kworker/3:1
[snip]
Workqueue: events deferred_probe_work_func
Call trace:
dump_backtrace+0x0/0x190
show_stack+0x14/0x20
dump_stack+0x90/0xb4
___might_sleep+0xec/0x110
__might_sleep+0x50/0x88
phy_g12a_usb3_pcie_cr_bus_addr.isra.0+0x80/0x1a8
phy_g12a_usb3_pcie_cr_bus_read+0x34/0x1d8
_regmap_read+0x60/0xe0
_regmap_update_bits+0xc4/0x110
regmap_update_bits_base+0x60/0x90
phy_g12a_usb3_pcie_init+0xdc/0x210
phy_init+0x74/0xd0
dwc3_meson_g12a_probe+0x2cc/0x4d0
platform_drv_probe+0x50/0xa0
really_probe+0x20c/0x3b8
driver_probe_device+0x68/0x150
__device_attach_driver+0xa8/0x170
bus_for_each_drv+0x64/0xc8
__device_attach+0xd8/0x158
device_initial_probe+0x10/0x18
bus_probe_device+0x90/0x98
deferred_probe_work_func+0x94/0xe8
process_one_work+0x1e0/0x338
worker_thread+0x230/0x458
kthread+0x134/0x138
ret_from_fork+0x10/0x1c
Fixes: 36077e16c0 ("phy: amlogic: Add Amlogic G12A USB3 + PCIE Combo PHY Driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds support for the Mixel DPHY as found on i.MX8 CPUs but since
this is an IP core it will likely be found on others in the future. So
instead of adding this to the nwl host driver make it a generic PHY
driver.
The driver supports the i.MX8MQ. Support for i.MX8QM and i.MX8QXP can be
added once the necessary system controller bits are in via
mixel_dphy_devdata.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Co-developed-by: Robert Chiras <robert.chiras@nxp.com>
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
'mask_com_pcs_ready' is only useful if 'has_phy_com_ctrl' is true.
Since msm8998_pciephy_cfg.has_phy_com_ctrl is false, let's drop
msm8998_pciephy_cfg.mask_com_pcs_ready altogether.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
After issuing a PHY_START request to the QMP, the hardware documentation
states that the software should wait for the PCS_READY_STATUS to become
1.
With the introduction of commit c9b589791f ("phy: qcom: Utilize UFS
reset controller") an additional 1ms delay was introduced between the
start request and the check of the status bit. This greatly increases
the chances for the hardware to actually becoming ready before the
status bit is read.
The result can be seen in that UFS PHY enabling is now reported as a
failure in 10% of the boots on SDM845, which is a clear regression from
the previous rare/occasional failure.
This patch fixes the "break condition" of the poll to check for the
correct state of the status bit.
Unfortunately PCIe on 8996 and 8998 does not specify the mask_pcs_ready
register, which means that the code checks a bit that's always 0. So the
patch also fixes these, in order to not regress these targets.
Fixes: 73d7ec899b ("phy: qcom-qmp: Add msm8998 PCIe QMP PHY support")
Fixes: e78f3d15e1 ("phy: qcom-qmp: new qmp phy driver for qcom-chipsets")
Cc: stable@vger.kernel.org
Cc: Evan Green <evgreen@chromium.org>
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Tested-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix sparse warning:
drivers/phy/ti/phy-am654-serdes.c:250:12: warning:
symbol 'serdes_am654_xlate' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct samsung_usb2_phy_driver {
...
struct samsung_usb2_phy_instance instances[0];
};
instance = devm_kzalloc(dev, sizeof(struct samsung_usb2_phy_driver) +
count * sizeof(struct samsung_usb2_phy_instance),
GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, instances, count),
GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 53 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.904365654@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Tegra210 SoC has four inputs that consume power in order to supply
the PLLs that drive the various USB, PCI and SATA pads.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Tegra124 SoC has four inputs that consume power in order to supply
the PLLs that drive the various USB, PCI and SATA pads.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We are not destroying the sysfs attribute groupe we registered during
the probe function which will make subsequent probe calls to that
driver fail. Correct that with adding a remove function which only
removes those attributes since the reference counting on clocks did its
job already.
Fixes: 415060b21f ("phy: usb: phy-brcm-usb: Add ability to force DRD mode to host or device")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch fixes memory leak at error paths of the probe function.
In for_each_child_of_node, if the loop returns, the driver should
call of_put_node() before returns.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Fixes: 1233f59f74 ("phy: Renesas R-Car Gen2 PHY driver")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation you should have received a
copy of the gnu general public license along with this program if
not see http www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 30 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.962665879@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 101 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190113.822954939@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 100 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.918357685@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error return from the call to clk_prepare_enable is not being assigned
to variable ret even though ret is being used to check if the call failed.
Fix this by adding in the missing assignment.
Addresses-Coverity: ("Logically dead code")
Fixes: 891a96f65a ("phy: qcom-qusb2: Add support for runtime PM")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Prior to the adoption of SPDX, it was difficult for tools to determine
the correct license due to incomplete or badly formatted license text.
The SPDX solves this issue, assuming people can correctly spell
"SPDX-License-Identifier" although this assumption is broken in some
places.
Since scripts/spdxcheck.py parses only lines that exactly matches to
the correct tag, it cannot (should not) detect this kind of error.
If the correct tag is missing, scripts/checkpatch.pl warns like this:
WARNING: Missing or malformed SPDX-License-Identifier tag in line *
So, people should notice it before the patch submission, but in reality
broken tags sometimes slip in. The checkpatch warning is not useful for
checking the committed files globally since large number of files still
have no SPDX tag.
Also, I am not sure about the legal effect when the SPDX tag is broken.
Anyway, these typos are absolutely worth fixing. It is pretty easy to
find suspicious lines by grep.
$ git grep --not -e SPDX-License-Identifier --and -e SPDX- -- \
:^LICENSES :^scripts/spdxcheck.py :^*/license-rules.rst
arch/arm/kernel/bugs.c:// SPDX-Identifier: GPL-2.0
drivers/phy/st/phy-stm32-usbphyc.c:// SPDX-Licence-Identifier: GPL-2.0
drivers/pinctrl/sh-pfc/pfc-r8a77980.c:// SPDX-Lincense-Identifier: GPL 2.0
lib/test_stackinit.c:// SPDX-Licenses: GPLv2
sound/soc/codecs/max9759.c:// SPDX-Licence-Identifier: GPL-2.0
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm PCIe2 PHY is based on design from Synopsys and found in
several different platforms where the QMP PHY isn't used.
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 24 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170026.162703968@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version this program is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 44 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091651.032047323@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 441 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071858.739733335@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and PHY driver patches for 5.2-rc1
There is the usual set of:
- USB gadget updates
- PHY driver updates and additions
- USB serial driver updates and fixes
- typec updates and new chips supported
- mtu3 driver updates
- xhci driver updates
- other tiny driver updates
Nothing really interesting, just constant forward progress.
All of these have been in linux-next for a while with no reported
issues. The usb-gadget and usb-serial trees were merged a bit "late",
but both of them had been in linux-next before they got merged here last
Friday.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNKuwg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymRUgCfa8Ri7KrCaBR5NHQcLhbdrX90ToQAmgNw7vpo
fqt0XpNM0CSa9O/gOr79
=8HFh
-----END PGP SIGNATURE-----
Merge tag 'usb-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver patches for 5.2-rc1
There is the usual set of:
- USB gadget updates
- PHY driver updates and additions
- USB serial driver updates and fixes
- typec updates and new chips supported
- mtu3 driver updates
- xhci driver updates
- other tiny driver updates
Nothing really interesting, just constant forward progress.
All of these have been in linux-next for a while with no reported
issues. The usb-gadget and usb-serial trees were merged a bit "late",
but both of them had been in linux-next before they got merged here
last Friday"
* tag 'usb-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (206 commits)
USB: serial: f81232: implement break control
USB: serial: f81232: add high baud rate support
USB: serial: f81232: clear overrun flag
USB: serial: f81232: fix interrupt worker not stop
usb: dwc3: Rename DWC3_DCTL_LPM_ERRATA
usb: dwc3: Fix default lpm_nyet_threshold value
usb: dwc3: debug: Print GET_STATUS(device) tracepoint
usb: dwc3: Do core validation early on probe
usb: dwc3: gadget: Set lpm_capable
usb: gadget: atmel: tie wake lock to running clock
usb: gadget: atmel: support USB suspend
usb: gadget: atmel_usba_udc: simplify setting of interrupt-enabled mask
dwc2: gadget: Fix completed transfer size calculation in DDMA
usb: dwc2: Set lpm mode parameters depend on HW configuration
usb: dwc2: Fix channel disable flow
usb: dwc2: Set actual frame number for completed ISOC transfer
usb: gadget: do not use __constant_cpu_to_le16
usb: dwc2: gadget: Increase descriptors count for ISOC's
usb: introduce usb_ep_type_string() function
usb: dwc3: move synchronize_irq() out of the spinlock protected block
...
*) Fix sun4i-usb PHY driver to get USB gadget working on H3/R40/V3/V3s
*) Fix cable state handling in phy-twl4030-usb driver to get rid of
regulator_put() warning
*) Fix linker errors and compilation warnings got with randconfig
*) Fix sparse warnings and .cocci warnings
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
iQJCBAABCgAsFiEEUXMr/TfP2p4suIY5Dlx4XIBNgtkFAly3IE0OHGtpc2hvbkB0
aS5jb20ACgkQDlx4XIBNgtlLdw//chLd7p15v9DZygo6QEaapO9aUogBZFeUmpJ8
9HuXiEeJxxqFemX+uplJ20yFWkJ2KgNG6bJltHPLDA6pUgv2xbGn5kNvAmxdaOSG
Sp8GIp2W1NQQwbCna1b+uLFFLd87aBu9nVcias2Kg3+TeCEyLzJvBWveluxthDSV
+3YlT7KwiDLm4iJx67PvyvGan5BhfJz4rCSYjOprv/BzS5vTF6ax4iyWh/cy2ABH
F53mvpAVJPNw3c+w6lj+Hwks4ZQ0LqebautwW8mBBJ9Dbb592qDNEY8QwaCcQLXn
suRdRHuuN8BrTYWfQed4YA+npcWf8fqHAQyxP8BiQtMwvoKFJGXjF7oHS7vD4zWT
9hWfP9F9/Qm90nrhssVEvAaClMb+3w8PrtUQouO6n+p+yZCq85PMZTfZNR6iHF5q
q3dEvuZy6QxnMSsmO4WFXSihK/c10NMRbG6+SlXDxHPVw3U+/elXeQOuU+ah/xMn
8/amZbEy3l+J0CjN5QwmECRmp9Y4UprW1WQRZrnmaNHc2PrqlNprCC8XNzuvuuCH
tlJ8iY0juMyzei8xjKFt1Q8xjkZXXfhCD45z0+JlsAsxmqvwvNkVU8k9zBQyOYik
jSyTO98wL0gqvJF6KTbLJYl/lRxstdKXM4vQa3MotPm8kTURGNtUR2ZOoAiIbjCO
Cv5PrTE=
=NbOP
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.1-rc-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into char-misc-next
Kishon writes:
phy: for 5.1-rc
*) Fix sun4i-usb PHY driver to get USB gadget working on H3/R40/V3/V3s
*) Fix cable state handling in phy-twl4030-usb driver to get rid of
regulator_put() warning
*) Fix linker errors and compilation warnings got with randconfig
*) Fix sparse warnings and .cocci warnings
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.1-rc-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
phy: sun4i-usb: Make sure to disable PHY0 passby for peripheral mode
phy: fix platform_no_drv_owner.cocci warnings
phy: mapphone-mdm6600: add gpiolib dependency
phy: ti: usb2: fix OMAP_CONTROL_PHY dependency
phy: allwinner: allow compile testing
phy: qcom-ufs: Make ufs_qcom_phy_disable_iface_clk static
phy: rockchip-typec: Make usb3_pll_cfg and dp_pll_cfg static
phy: phy-twl4030-usb: Fix cable state handling
*) Add a new *release* phy_ops invoked when the consumer relinquishes PHY
that can be used to undo the operation performed in xlate
*) Add new driver to support USB2 PHY and shared USB3 + PCIE PHY in Amlogic
G12A SoC Family.
*) Add new driver to support for Broadcom's Stingray USB PHY (Type 1 has
one super speed PHY and one high speed PHY, Type 2 has one high speed PHY)
*) Add new driver to support USB PHY in hi3660 SoC of Hisilicon
*) Add new driver to support UFS M-PHY in MediaTek SoC
*) Add new driver to support XUSB pad controller in Tegra186 SoCs
*) Add new driver to support SERDES in TI's AM654 platform
*) Add support for generation 2 USB2 PHY and gneration 3 USB2 PHY in r8a77470
to phy-rcar-gen2.c and phy-rcar-gen3-usb2.c respectively
*) Add support for PCIe QMP PHY support in msm8998 to phy-qcom-qmp.c
*) Add support for SERDES6G in phy-ocelot-serdes.c
*) Add support to set drive impedance from device tree in phy-rockchip-emmc.c
*) Add support to power up/down the VBUS voltage rail in phy-fsl-imx8mq-usb.c
*) Add support to shut off regulators that power UFS during system suspend
*) Re-design phy-rcar-gen3-usb2.c to create separate PHY instances for each
channel which helps to enable/disable interrupts for each instance
independently
*) Fix PCIe power up sequence to follow the TRM in order to ensure the DPLL &
PHY operates correctly over the entire temperature range.
*) Use devm_clk_get_optional to get optional clocks instead of adding
custom error checks
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=BAzr
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 5.2
*) Add a new *release* phy_ops invoked when the consumer relinquishes PHY
that can be used to undo the operation performed in xlate
*) Add new driver to support USB2 PHY and shared USB3 + PCIE PHY in Amlogic
G12A SoC Family.
*) Add new driver to support for Broadcom's Stingray USB PHY (Type 1 has
one super speed PHY and one high speed PHY, Type 2 has one high speed PHY)
*) Add new driver to support USB PHY in hi3660 SoC of Hisilicon
*) Add new driver to support UFS M-PHY in MediaTek SoC
*) Add new driver to support XUSB pad controller in Tegra186 SoCs
*) Add new driver to support SERDES in TI's AM654 platform
*) Add support for generation 2 USB2 PHY and gneration 3 USB2 PHY in r8a77470
to phy-rcar-gen2.c and phy-rcar-gen3-usb2.c respectively
*) Add support for PCIe QMP PHY support in msm8998 to phy-qcom-qmp.c
*) Add support for SERDES6G in phy-ocelot-serdes.c
*) Add support to set drive impedance from device tree in phy-rockchip-emmc.c
*) Add support to power up/down the VBUS voltage rail in phy-fsl-imx8mq-usb.c
*) Add support to shut off regulators that power UFS during system suspend
*) Re-design phy-rcar-gen3-usb2.c to create separate PHY instances for each
channel which helps to enable/disable interrupts for each instance
independently
*) Fix PCIe power up sequence to follow the TRM in order to ensure the DPLL &
PHY operates correctly over the entire temperature range.
*) Use devm_clk_get_optional to get optional clocks instead of adding
custom error checks
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (51 commits)
dt-bindings: phy-qcom-qmp: Tweak qcom,msm8998-qmp-ufs-phy
dt-bindings: phy-qcom-qmp: Add qcom,msm8998-qmp-pcie-phy
phy: Add usb phy support for hi3660 Soc of Hisilicon
dt-bindings: phy: Add support for HiSilicon's hi3660 USB PHY
scsi: phy: mediatek: fix typo in author's email address
phy: ocelot-serdes: Add support for SERDES6G muxing
phy: fsl-imx8mq-usb: add support for VBUS power control
dt-bindings: phy-imx8mq-usb: add optional vbus supply regulator
phy: qcom-qmp: Add msm8998 PCIe QMP PHY support
phy: ti: am654-serdes: Support all clksel values
phy: ti: Add a new SERDES driver for TI's AM654x SoC
dt-bindings: phy: ti: Add dt binding documentation for SERDES in AM654x SoC
phy: core: Invoke pm_runtime_get_*/pm_runtime_put_* before invoking reset callback
phy: core: Add *release* phy_ops invoked when the consumer relinquishes PHY
phy: phy-meson-gxl-usb2: get optional clock by devm_clk_get_optional()
phy: socionext: get optional clock by devm_clk_get_optional()
phy: qcom-qusb2: get optional clock by devm_clk_get_optional()
phy: phy-mtk-tphy: get optional clock by devm_clk_get_optional()
phy: renesas: rcar-gen3-usb2: enable/disable independent irqs
phy: renesas: rcar-gen3-usb2: Use pdev's device pointer on dev_vdbg()
...
This driver handles usb phy power on and shutdown for hi3660 Soc of
Hisilicon.
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Pengcheng Li <lpc.li@hisilicon.com>
Cc: Jianguo Sun <sunjianguo1@huawei.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jiancheng Xue <xuejiancheng@hisilicon.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Yu Chen <chenyu56@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There is a typo in the module author's email address. Fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds support to the PHY driver to power up/down the VBUS
voltage rail at the appropriate times.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support to select all 16 CLKSEL combinations that are shown in
"SerDes Reference Clock Distribution" in AM65 TRM.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a new SERDES driver for TI's AM654x SoC which configures
the SERDES only for PCIe. Support fo USB3 will be added later.
SERDES in am654x has three input clocks (left input, externel reference
clock and right input) and two output clocks (left output and right
output) in addition to a PLL mux clock which the SERDES uses for Clock
Multiplier Unit (CMU refclock).
The PLL mux clock can select from one of the three input clocks.
The right output can select between left input and external reference
clock while the left output can select between the right input and
external reference clock.
The driver has support to select PLL mux and left/right output mux as
specified in device tree.
[rogerq@ti.com: Fix boot lockup caused by accessing a structure member
(hw->init) allocated in stack of probe() and accessed in get_parent]
[rogerq@ti.com: Fix "Failed to find the parent" warnings]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PHY drivers may try to access PHY registers in the ->reset() callback.
Invoke phy_pm_runtime_get_sync() before invoking the ->reset() callback
so that the PHY drivers don't have to enable clocks by themselves before
accessing PHY registers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a new phy_ops *release* invoked when the consumer relinquishes the
PHY using phy_put/devm_phy_put. The initializations done by the PHY
driver in of_xlate call back can be can be cleaned up here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use devm_clk_get_optional() to get optional clock
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use devm_clk_get_optional() to get optional clock
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use devm_clk_get_optional() to get optional clock
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use devm_clk_get_optional() to get optional clock
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Since the previous code enabled/disabled the irqs both OHCI and EHCI,
it is possible to cause unexpected interruptions. To avoid this,
this patch creates multiple phy instances from phandle and
enables/disables independent irqs by the instances.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Tested-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
To implement multiple phy instances in the future, this patch uses
pdev's device pointer on dev_vdbg() instead of the phy's device
pointer.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds support for r8a77470 (RZ/G1C). We can reuse this driver for
initializing timing/interrupt generation registers.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds support for RZ/G1C (r8a77470) SoC. RZ/G1C SoC has a
PLL register shared between hsusb0 and hsusb1. Compared to other RZ/G1
and R-Car Gen2/3, USB Host needs to deassert the pll reset.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-and-Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
TRM [1] mentions that we need to power up
PCIESS_PHY_TX and PCIESS_PHY_RX before configuring
PCIe_PHY_RX SCP settings.
See "Table 26-81. PCIePHY Subsystem Low-Level Programming Sequence".
[1] DRA75x, DRA74x TRM - http://www.ti.com/lit/ug/sprui30f/sprui30f.pdf
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
As per "Table 26-7. SATA PHY Subsystem Low-Level Programming Sequence"
in TRM [1] we need to turn on SATA_PHY_TX before SATA_PHY_RX.
[1] DRA75x, DRA74x TRM - http://www.ti.com/lit/ug/sprui30f/sprui30f.pdf
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
For increased DPLL stability use the settings recommended in
the TRM [1] for PHY_RX registers for SATA and USB.
For SATA we need to use spread spectrum settings even
though we don't have spread spectrum enabled. The
suggested non-spread spectrum settings don't work.
[1] DRA75x, DRA74x TRM - http://www.ti.com/lit/ug/sprui30f/sprui30f.pdf
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Introduce a mode property in the driver data so that
we don't have to keep using "of_device_is_compatible()"
throughtout the driver.
No functional change.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There seems to be a missing bit-wise or operator when setting val,
fix this by adding it in.
Fixes: 2796ceb0c1 ("phy: ti-pipe3: Update pcie phy settings")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The rockchip-emmc PHY can be configured with different
drive impedance values. Currenlty a value of 50 Ohm is
hard coded into the driver.
This patch introduces the DTS property 'drive-impedance-ohm'
for the rockchip-emmc phy node, which uses the value from the DTS
to setup the drive impedance accordingly.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The phy code was using implicit sequencing between the PHY driver
and the UFS driver to implement certain hardware requirements.
Specifically, the PHY reset register in the UFS controller needs
to be deasserted before serdes start occurs in the PHY.
Before this change, the code was doing this by utilizing the two
phy callbacks, phy_init() and phy_poweron(), as "init step 1" and
"init step 2", where the UFS driver would deassert reset between
these two steps.
This makes it challenging to power off the regulators in suspend,
as regulators are initialized in init, not in poweron(), but only
poweroff() is called during suspend, not exit().
For UFS, move the actual firing up of the PHY to phy_poweron() and
phy_poweroff() callbacks, rather than init()/exit(). UFS calls
phy_poweroff() during suspend, so now all clocks and regulators for
the phy can be powered down during suspend.
QMP is a little tricky because the PHY is also shared with PCIe and
USB3, which have their own definitions for init() and poweron(). Rename
the meaty functions to _enable() and _disable() to disentangle from the
PHY core names, and then create two different ops structures: one for
UFS and one for the other PHY types.
In phy-qcom-ufs, remove the 'is_powered_on' and 'is_started' guards,
as the generic PHY code does the reference counting. The
14/20nm-specific init functions get collapsed into the generic power_on()
function, with the addition of a calibrate() callback specific to 14/20nm.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Move the PHY reset from ufs-qcom into the respective PHYs. This will
allow us to merge the two phases of UFS PHY initialization.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds support for the shared USB3 + PCIE PHY found in the
Amlogic G12A SoC Family.
It supports USB3 Host mode or PCIE 2.0 mode, depending on the layout of
the board.
Selection is done by the #phy-cells, making the mode static and exclusive.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds support for the USB2 PHY found in the Amlogic G12A SoC Family.
It supports Host and/or Peripheral mode, depending on it's position.
The first PHY is only used as Host, but the second supports Dual modes
defined by the USB Control Glue HW in front of the USB Controllers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
USB PHY driver supports two types of stingray USB PHYs
- Type 1 is a combo PHY contains two PHYs, one SS and one HS.
- Type 2 is a single HS PHY.
These two PHY versons support both Generic xHCI host controller driver
and BDC Broadcom device controller driver.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for the XUSB pad controller found on Tegra186 SoCs. It is
mostly similar to the same IP found on earlier chips, but the number of
pads exposed differs, as do the programming sequences.
Note that the DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL power
supplies of the XUSB pad controller require strict power sequencing and
are therefore controlled by the PMIC on Tegra186.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
[dan.carpenter@oracle.com: Fix testing the wrong variable in probe()]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[yuehaibing@huawei.com: Make two functions static to fix sparse warning]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Support enabling various supplies needed to provide power to the PLLs
and logic used to drive the USB, PCI and SATA pads.
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The device tree bindings document the "mode" property of "ports"
subnodes, but the driver was not parsing the property. In preparation
for adding role switching, parse the property at probe time.
Based on work by JC Kuo <jckuo@nvidia.com>.
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tegra186 USB2 pads and USB3 pads do not have hardware mux for changing
the pad function. For such "lanes", we can skip the lane mux register
programming.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
On platforms where the MUSB and HCI controllers share PHY0, PHY passby
is required when using the HCI controller with the PHY, but it must be
disabled when the MUSB controller is used instead.
Without this, PHY0 passby is always enabled, which results in broken
peripheral mode on such platforms (e.g. H3/H5).
Fixes: ba4bdc9e1d ("PHY: sunxi: Add driver for sunxi usb phy")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
gcc points out that when CONFIG_GPIOLIB is disabled,
gpiod_get_array_value_cansleep() returns 0 but fails to set its output:
drivers/phy/motorola/phy-mapphone-mdm6600.c: In function 'phy_mdm6600_status':
drivers/phy/motorola/phy-mapphone-mdm6600.c:220:24: error: 'values[0]' is used uninitialized in this function [-Werror=uninitialized]
This could be fixed more generally in gpiolib by returning a failure
code, but for this specific case, the easier workaround is to add a
gpiolib dependency.
Fixes: 5d1ebbda03 ("phy: mapphone-mdm6600: Add USB PHY driver for MDM6600 on Droid 4")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
With randconfig build testing on arm64, we can run into a configuration
that has CONFIG_OMAP_CONTROL_PHY=m and CONFIG_OMAP_USB2=y, which in turn
causes a link failure:
drivers/phy/ti/phy-omap-usb2.o: In function `omap_usb_phy_power':
phy-omap-usb2.c:(.text+0x17c): undefined reference to `omap_control_phy_power'
I could not come up with a good way to correctly describe the relation
of the two symbols, but if we just select CONFIG_OMAP_CONTROL_PHY
during compile testing, we can no longer run into the broken configuration.
Fixes: 6777cee3a8 ("phy: ti: usb2: Add support for AM654 USB2 PHY")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Some allwinner specific drivers can be built for testing purposes
on non-sunxi configurations, which then results in a harmless
warning:
WARNING: unmet direct dependencies detected for PHY_SUN6I_MIPI_DPHY
Depends on [n]: ARCH_SUNXI [=n] && HAS_IOMEM [=y] && OF [=y] && RESET_CONTROLLER [=y]
Selected by [y]:
- DRM_SUN6I_DSI [=y] && HAS_IOMEM [=y] && DRM_SUN4I [=y]
Allow compile-test here as well to avoid the warning, and improve
overall build coverage.
Fixes: 5d134abf95 ("phy: Move Allwinner A31 D-PHY driver to drivers/phy/")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix sparse warning:
drivers/phy/qualcomm/phy-qcom-ufs.c:462:6:
warning: symbol 'ufs_qcom_phy_disable_iface_clk' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix sparse warning:
drivers/phy/rockchip/phy-rockchip-typec.c:403:16: warning: symbol 'usb3_pll_cfg' was not declared. Should it be static?
drivers/phy/rockchip/phy-rockchip-typec.c:420:16: warning: symbol 'dp_pll_cfg' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
With the recent regulator changes I noticed new warnings on doing rmmod of
phy-twl4030-usb:
WARNING: CPU: 0 PID: 1080 at drivers/regulator/core.c:2046 _regulator_put
...
Turns out we can currently miss disconnect at least for cases where status
is 0 and linkstat is 0. And in that case doing rmmod phy-twl4030-usb will
produce the regulator_put() warning.
This is because the missed disconnect causes unbalanced PM runtime calls
and the regulators will be on exit.
Let's fix the issue by using an atomic flag for the cable state to make
sure that PM runtime won't get out of sync with the cable state. That
way we can also simplify the code a bit.
Note that we can also drop the old comments, those relate to issues that
the battery charger driver and musb driver is dealing with rather than
the USB PHY driver.
Cc: NeilBrown <neilb@suse.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
While only the first PHY supports mode switching, the remaining PHYs
work in USB host mode. They should support set_mode with mode=USB_HOST
instead of failing. This is especially needed now that the USB core does
set_mode for all USB ports, which was added in commit b97a313483 ("usb:
core: comply to PHY framework").
Make set_mode with mode=USB_HOST a no-op instead of failing for the
non-OTG USB PHYs.
Fixes: 6ba43c2919 ("phy-sun4i-usb: Add support for phy_set_mode")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJcfzdFAAoJEAx081l5xIa+QxsP/A6QP+gx4vQ8XXikaJMNz89e
59TAbXHW/2qFMHRtUesuB2bc1a2cw2ppFsrryG7c4HqjKDDHna7Yx2JzZYL0MmNh
SpJYL4yMuu/2TmyCouaAYzzP+5Supdosfif4LRn3269DH0i5MWXL+NVrbeB47blG
XwjQTu46yfn06IFAo5bI2jMqSuPCDd4Hzpyixpvmjt+r16XwoH5nGUrDCHG8t/jV
+PUZCYAjn71in6Z66MKZv/EVCVFfTnaVJ2KEgw7e+vWxnERkRh/xnRO6KIXMD5O1
vo2qc2vbxkGpjaE6pDzC/2e5pRJT8Ks0t50jYjbVF+6nHpP5XIPvAXH4R2QdTA7B
Jiu8N0oz6wj0H3AJ/V38rEHWW8zgOfXkhbRBfmfQ9NfgiEfwxqCVgspIOwei4oVw
hvMXYUBM1CU+JIfW6w7ZT4oHALUlnCpnr5DQRdCNRm8zjClyNfIAoJIJrOtqmX44
qjEzSgxb89ZtS7c0yislSBaovgAmcM3I+aq5I4xokdY0hFEZ6QomuKunyuQ8pBYa
3gsvMEReLxETffhhYpjBt5+b5IgB49nf3Y38CKFurv32Sp0p0YgK0qVo8qRQHclj
QIJ+3+zQMCX20swYpCWXhOPUIwtQppdKhWzg12my8rL2VgTlYhjlEbL4EL+Wk+hv
6Ipulthzn0RyrSK9Dojh
=GlRQ
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-03-06' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This is the main drm pull request for the 5.1 merge window.
The big changes I'd highlight are:
- nouveau has HMM support now, there is finally an in-tree user so we
can quieten down the rip it out people.
- i915 now enables fastboot by default on Skylake+
- Displayport Multistream support has been refactored and should
hopefully be more reliable.
Core:
- header cleanups aiming towards removing drmP.h
- dma-buf fence seqnos to 64-bits
- common helper for DP mst hotplug for radeon,i915,amdgpu + new
refcounting scheme
- MST i2c improvements
- drm_syncobj_cb removal
- ARM FB compression fourcc
- P010 + P016 fourcc
- allwinner tiled format modifier
- i2c over aux I2C_M_STOP support
- DRM_AUTH handling fixes
TTM:
- ref/unref renaming
New driver:
- ARM komeda display driver
scheduler:
- refactor mirror list handling
- rework hw fence processing
- 0 run queue entity fix
bridge:
- TI DS90C185 LVDS bridge
- thc631lvdm83d bridge improvements
- cadence + allwinner DSI ported to generic phy
panels:
- Sitronix ST7701 panel
- Kingdisplay KD097D04
- LeMaker BL035-RGB-002
- PDA 91-00156-A0
- Innolux EE101IA-01D
i915:
- Enable fastboot by default on SKL+/VLV/CHV
- Export RPCS configuration for ICL media driver
- Coffelake PCI ID
- CNL clocks setup fixes
- ACPI/PMIC support for MIPI/DSI
- Per-engine WA init for all engines
- Shrinker locking fixes
- Kerneldoc updates
- Lots of ring improvements and reset fixes
- Coffeelake GVT Support
- VFIO GVT EDID Region support
- runtime PM wakeref tracking
- ILK->IVB primary plane enable delays
- userptr mutex locking fixes
- DSI fixes
- LVDS/TV cleanups
- HW readout fixes
- LUT robustness fixes
- ICL display and watermark fixes
- gem mmap race fix
amdgpu:
- add scheduled dependencies interface
- DCC on scanout surfaces
- vega10/20 BACO support
- Multiple IH rings on soc15
- XGMI locking fixes
- DC i2c/aux cleanups
- runtime SMU debug interface
- Kexec improvmeents
- SR-IOV fixes
- DC freesync + ABM fixes
- GDS fixes
- GPUVM fixes
- vega20 PCIE DPM switching fixes
- Context priority handling fixes
radeon:
- fix missing break in evergreen parser
nouveau:
- SVM support via HMM
msm:
- QCOM Compressed modifier support
exynos:
- s5pv210 rotator support
imx:
- zpos property support
- pending update fixes
v3d:
- cache flush improvments
vc4:
- reflection support
- HDMI overscan support
tegra:
- CEC refactoring
- HDMI audio fixes
- Tegra186 prep work
- SOR crossbar device tree fixes
sun4i:
- implicit fencing support
- YUV and scalar support improvements
- A23 support
- tiling fixes
atmel-hlcdc:
- clipping and rotation property fixes
qxl:
- BO and PRIME improvements
- generic fbdev emulation
dw-hdmi:
- HDMI 2.0 2160p
- YUV420 ouput
rockchip:
- implicit fencing support
- reflection proerties
virtio-gpu:
- use generic fbdev emulation
tilcdc:
- cpufreq vs crtc init fix
rcar-du:
- R8A774C0 support
- D3/E3 RGB output routing fixes and DPAD0 support
- RA87744 LVDS support
bochs:
- atomic and generic fbdev emulation
- ID mismatch error on bochs load
meson:
- remove firmware fbs"
* tag 'drm-next-2019-03-06' of git://anongit.freedesktop.org/drm/drm: (1130 commits)
drm/amd/display: Use vrr friendly pageflip throttling in DC.
drm/imx: only send commit done event when all state has been applied
drm/imx: allow building under COMPILE_TEST
drm/imx: imx-tve: depend on COMMON_CLK
drm/imx: ipuv3-plane: add zpos property
drm/imx: ipuv3-plane: add function to query atomic update status
gpu: ipu-v3: prg: add function to get channel configure status
gpu: ipu-v3: pre: add double buffer status readback
drm/amdgpu: Bump amdgpu version for context priority override.
drm/amdgpu/powerplay: fix typo in BACO header guards
drm/amdgpu/powerplay: fix return codes in BACO code
drm/amdgpu: add missing license on baco files
drm/bochs: Fix the ID mismatch error
drm/nouveau/dmem: use dma addresses during migration copies
drm/nouveau/dmem: use physical vram addresses during migration copies
drm/nouveau/dmem: extend copy function to allow direct use of physical addresses
drm/nouveau/svm: new ioctl to migrate process memory to GPU memory
drm/nouveau/dmem: device memory helpers for SVM
drm/nouveau/svm: initial support for shared virtual memory
drm/nouveau: prepare for enabling svm with existing userspace interfaces
...
Here is the big USB/PHY driver pull request for 5.1-rc1.
The usual set of gadget driver updates, phy driver updates (you will
have a merge issue with Kconfig and Makefile), xhci updates, and typec
additions. Also included in here are a lot of small cleanups and fixes
and driver updates where needed.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXH+hsw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynfNwCgqKKg+MxJ9pFjrwfWYOrbk+BBe2UAn2Elp4ia
8FTdneQfN2J8Hhc6KGXE
=Kx9I
-----END PGP SIGNATURE-----
Merge tag 'usb-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB/PHY driver pull request for 5.1-rc1.
The usual set of gadget driver updates, phy driver updates, xhci
updates, and typec additions. Also included in here are a lot of small
cleanups and fixes and driver updates where needed.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (167 commits)
wusb: Remove unnecessary static function ckhdid_printf
usb: core: make default autosuspend delay configurable
usb: core: Fix typo in description of "authorized_default"
usb: chipidea: Refactor USB PHY selection and keep a single PHY
usb: chipidea: Grab the (legacy) USB PHY by phandle first
usb: chipidea: imx: set power polarity
dt-bindings: usb: ci-hdrc-usb2: add property power-active-high
usb: chipidea: imx: remove unused header files
usb: chipidea: tegra: Fix missed ci_hdrc_remove_device()
usb: core: add option of only authorizing internal devices
usb: typec: tps6598x: handle block writes separately with plain-I2C adapters
usb: xhci: Fix for Enabling USB ROLE SWITCH QUIRK on INTEL_SUNRISEPOINT_LP_XHCI
usb: xhci: fix build warning - missing prototype
usb: xhci: dbc: Fixing typo error.
usb: xhci: remove unused member 'parent' in xhci_regset struct
xhci: tegra: Prevent error pointer dereference
USB: serial: option: add Telit ME910 ECM composition
usb: core: Replace hardcoded check with inline function from usb.h
usb: core: skip interfaces disabled in devicetree
usb: typec: mux: remove redundant check on variable match
...
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlxqHJYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGWl8H/jPI4EipzD2GbnjZ
GaFpMBBjcXBaVmoA+Y69so+7BHx1Ql+5GQtqbK0RHJRb9qEPLw3FBhHNjM/N8Sgf
nSrK+GnBZp9s+k/NR/Yf2RacUR3jhz+Q9JEoQd3u9bFUeQyvE8Rf3vgtoBBwFOfz
+t7N1memYVF3asLGWB4e4sP1YVMGfseTQpSPojvM30YWM86Bv+QtSx1AGgHczQIM
kMKealR8ZPelN6JAXgLhQ5opDojBrE4YKB98pwsMDI6abz0Tz2JLFEUTTxsv5XNN
o/Iz+XDoylskEyxN2unNWfHx7Swkvoklog8J/hDg5XlTvipL/WkT66PHBgcGMNvj
BW9GgU8=
=ZizU
-----END PGP SIGNATURE-----
Merge v5.0-rc7 into drm-next
Backmerging for nouveau and imx that needed some fixes for next pulls.
Signed-off-by: Dave Airlie <airlied@redhat.com>
*) Add a new driver to support Armada 3700 COMPHY IP (supports SATA, USB3,
PCIe)
*) Add a new driver to support Armada UTMI PHY
*) Add a new driver to support Cadence D-PHY
*) Extend omap-usb2 PHY driver to be used for AM654 USB2 PHY
*) Extend qcom-qmp PHY driver to be used for UFS PHY and USB3 PHY in Qualcomm
MSM8998
*) Extend qcom-qusb2 PHY driver to support QUSB2 PHY in Qualcomm MSM8998
*) Remove module specific code that is present for drivers that can be only
built-in
*) Allow Freescale IMX8MQ USB to be used for multiple SoCs and not just
i.MX8MQ
*) Cleanups such as switch to SPDX identifier, use readl_poll_timeout macro,
remove unused headers etc.,
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=wNhh
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 5.1
*) Add a new driver to support Armada 3700 COMPHY IP (supports SATA, USB3,
PCIe)
*) Add a new driver to support Armada UTMI PHY
*) Add a new driver to support Cadence D-PHY
*) Extend omap-usb2 PHY driver to be used for AM654 USB2 PHY
*) Extend qcom-qmp PHY driver to be used for UFS PHY and USB3 PHY in Qualcomm
MSM8998
*) Extend qcom-qusb2 PHY driver to support QUSB2 PHY in Qualcomm MSM8998
*) Remove module specific code that is present for drivers that can be only
built-in
*) Allow Freescale IMX8MQ USB to be used for multiple SoCs and not just
i.MX8MQ
*) Cleanups such as switch to SPDX identifier, use readl_poll_timeout macro,
remove unused headers etc.,
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (32 commits)
phy: qcom-qmp: Add QMP UFS PHY support for msm8998
dt-bindings: phy-qcom-qmp: Add qcom,msm8998-qmp-ufs-phy
phy: bcm-sr-pcie: Change operation when PIPEMUX=1
phy: Add Cadence D-PHY support
dt-bindings: phy: Move the Cadence D-PHY bindings
phy: dphy: Clarify lanes parameter documentation
phy: dphy: Change units of wakeup and init parameters
phy: dphy: Remove unused header
MAINTAINERS: phy: fill Armada 3700 PHY drivers entry
dt-bindings: phy: mvebu-utmi: add UTMI PHY bindings
phy: add A3700 UTMI PHY driver
MAINTAINERS: phy: add entry for Armada 3700 COMPHY driver
dt-bindings: phy: mvebu-comphy: extend the file to describe a3700 bindings
phy: add A3700 COMPHY support
phy: mvebu-cp110-comphy: fix port check in ->xlate()
phy: armada375-usb2: switch to SPDX license identifier
phy: make phy-armada375-usb2 explicitly non-modular
phy: make phy-mvebu-sata explicitly non-modular
phy: make phy-core explicitly non-modular
phy: qcom-qusb2: Add QUSB2 PHY support for msm8998
...
Use same init sequence as sdm845.
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for the Armada 38x common phy to allow us to change the
speed of the Ethernet serdes lane. This driver only supports
manipulation of the speed, it does not support configuration of the
common phy.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PIPEMIX=1, change the operation from 2x8 EP to 1x8 EP + 1x8 RC.
Signed-off-by: Qingmin Liu <qingmin.liu@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cadence has designed a D-PHY that can be used by the, currently in tree,
DSI bridge (DRM), CSI Transceiver and CSI Receiver (v4l2) drivers.
Only the DSI driver has an ad-hoc driver for that phy at the moment, while
the v4l2 drivers are completely missing any phy support. In order to make
that phy support available to all these drivers, without having to
duplicate that code three times, let's create a generic phy framework
driver.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Init and wakeup D-PHY parameters are in the micro/milliseconds range,
putting the values real close to the types limits if they were in
picoseconds.
Move them to microseconds which should be better fit.
Suggested-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Marvell Armada 3700 SoC has two USB controllers, each of them being
wired to an internal UTMI PHY. Add a driver to control them.
Igal Liberman worked on supporting the PHY, I took the while 'register
configuration' from his work and rewrote almost entirely the
driver/bindings around it.
Co-developed-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a driver to support COMPHY, a hardware block providing shared
serdes PHYs on Marvell Armada 3700. This driver uses SMC calls and
rely on having an up-to-date firmware.
SATA, PCie and USB3 host mode have been tested successfully with an
ESPRESSObin. (HS)SGMII mode cannot be tested with this platform.
Evan worked on the original driver structure and Grzegorz on the SMC
calls rework. The structure of this driver has been copied from
Antoine Tenart work on CP110 COMPHY driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Co-developed-by: Evan Wang <xswang@marvell.com>
Signed-off-by: Evan Wang <xswang@marvell.com>
Co-developed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
So far the PHY ->xlate() callback was checking if the port was
"invalid" before continuing, meaning that the port has not been used
yet. This check is not correct as there is no opposite call to
->xlate() once the PHY is released by the user and the port will
remain "valid" after the first phy_get()/phy_put() calls. Hence, if
this driver is built as a module, inserted, removed and inserted
again, the PHY will appear busy and the second probe will fail.
To fix this, just drop the faulty check and instead verify that the
port number is valid (ie. in the possible range).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Kconfig currently controlling compilation of this code is:
drivers/phy/marvell/Kconfig:config ARMADA375_USBCLUSTER_PHY
drivers/phy/marvell/Kconfig: def_bool y
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple of traces of modular infrastructure, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Kconfig currently controlling compilation of this code is:
drivers/phy/Kconfig:config PHY_MVEBU_SATA
drivers/phy/Kconfig: def_bool y
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple of traces of modular infrastructure, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Kconfig currently controlling compilation of this code is:
drivers/phy/Kconfig:config GENERIC_PHY
drivers/phy/Kconfig: bool "PHY Core"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't remove module.h since the file is using other modular fcns
(to load other phy modules) even though the core support itself is
non-modular.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
MSM8998 contains one QUSB2 PHY which is very similar to the existing
sdm845 support.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
That property is no used in mainline and is not documented. The only
board using that property is the rk33-99-evb-rev1 and -rev2 in the
vendor kernel. The existence of a further -rev3 (which also looks way
better cared for compared rev1+2) indicates that the older ones are
probably some sort of preproduction models, where some wiring (on the soc
or board) may have gone wrong.
It is also not clear why this is a hardware-description or a DT
property, so, as noboby seems to care of this just drop reading that
property.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
MSM8998 contains a single QMP v3 USB3 phy similar to the existing sdm845
support.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix the typo flase -> false and clean up the kernel-doc documentation in
phy-rockchip-inno.usb2.c and fix the following warnings when documentation
is built.
:58: warning: missing initial short description
:69: warning: cannot understand function prototype: 'enum usb_chg_state '
:97: warning: missing initial short description
:136: warning: cannot understand function prototype: 'struct rockchip_usb2phy_port_cfg '
:157: warning: cannot understand function prototype: 'struct rockchip_usb2phy_cfg '
:163: warning: Function parameter or member 'port_cfgs' not described in 'rockchip_usb2phy_cfg'
:187: warning: cannot understand function prototype: 'struct rockchip_usb2phy_port '
:204: warning: Function parameter or member 'port_cfg' not described in 'rockchip_usb2phy_port'
:207: warning: missing initial short description
:234: warning: Function parameter or member 'dev' not described in 'rockchip_usb2phy'
:234: warning: Function parameter or member 'clk480m_hw' not described in 'rockchip_usb2phy'
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for the USB2 PHY on the AM654 SoC.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
TI_PIPE3 and OMAP_USB2 don't depend on OMAP_OCP2SCP
for build.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
If clk_get() returns -EPROBE_DEFER then we should just
return instead of falling back to old clock name.
Use clk_prepare_enable() and clk_disable_unprepare() instead
of splitting up prepare/unprepare from enable/disable.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The private copy of readl_poll_timeout is no longer needed.
Use the implementation in iopoll.h instead.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Since this is going to be used on more SoCs than just i.MX8MQ,
make the dependency here more generic.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Here are a number of small USB and PHY driver fixes for 5.0-rc4.
Nothing major at all, just the usual selection of USB gadget bugfixes,
some new USB serial driver ids, some SPDX fixes, and some PHY driver
fixes for reported issues.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXEr9Iw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yltXACg1ycTrlsIDEtj0fQb0KpgmovzYMEAn02nv62w
+6bHM1m+RZvKw5DnOrKb
=g6YM
-----END PGP SIGNATURE-----
Merge tag 'usb-5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY fixes from Greg KH:
"Here are a number of small USB and PHY driver fixes for 5.0-rc4.
Nothing major at all, just the usual selection of USB gadget bugfixes,
some new USB serial driver ids, some SPDX fixes, and some PHY driver
fixes for reported issues.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: keyspan_usa: add proper SPDX lines for .h files
USB: EHCI: ehci-mv: add MODULE_DEVICE_TABLE
USB: leds: fix regression in usbport led trigger
usb: chipidea: fix static checker warning for NULL pointer
MAINTAINERS: email address update in MAINTAINERS entries
USB: usbip: delete README file
USB: serial: pl2303: add new PID to support PL2303TB
usb: dwc2: gadget: Fix Remote Wakeup interrupt bit clearing
phy: ath79-usb: Fix the main reset name to match the DT binding
phy: ath79-usb: Fix the power on error path
phy: fix build breakage: add PHY_MODE_SATA
phy: ti: ensure priv is not null before dereferencing it
USB: serial: ftdi_sio: fix GPIO not working in autosuspend
usb: gadget: Potential NULL dereference on allocation error
usb: dwc3: gadget: Fix the uninitialized link_state when udc starts
usb: dwc3: gadget: Clear req->needs_extra_trb flag on cleanup
usb: dwc3: gadget: synchronize_irq dwc irq in suspend
USB: serial: simple: add Motorola Tetra TPG2200 device id
I submitted this driver several times before it got accepted. The
first series hasn't been accepted but the DTS binding did made it.
I then made a second series that added generic reset support to the
PHY core, this in turn required a change to the DT binding. This
second series seemed to have been ignored, so I did a third one
without the change to the PHY core and the DT binding update, and this
last attempt finally made it.
But two months later the DT binding update from the second series has
been integrated too. So now the driver doesn't match the binding and
the only DTS using it. This patch fix the driver to match the new
binding.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In the power on function the error path doesn't return the suspend
override to its proper state. It should should deassert this reset
line to enable the suspend override.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Jon Hunter