This adds support for
- CONFIG_ARC_TIMERS : legacy 32-bit TIMER0 and TIMER1 which count UP
from @CNT to @LIMIT, before optionally triggering an interrupt.
These are programmed using ARC auxiliary register interface.
These are present in all ARC cores (ARC700 and ARC HS38)
TIMER0 serves as clockevent for all ARC linux builds.
TIMER1 is used for clocksource in arc700 builds.
- CONFIG_ARC_TIMERS_64BIT: 64-bit counters, RTC and GFRC found in
ARC HS38 cores. These are independnet IP blocks with different
programming model respectively.
Link: http://lkml.kernel.org/r/20161111231132.GA4186@mai
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Also remove the dependency on ARCv2, to increase compile coverage for
!ARCV2 builds
Acked-by: Daniel Lezcano <daniel.lezcnao@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
to allow future git mv of the driver into drivers/clocksource
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The original distinction was done as they were developed at different
times and primarily because they are specific to UP (RTC) and SMP (GFRC).
But given that driver handles that at runtime, (i.e. not allowing
RTC as clocksource in SMP), we can simplify things a bit.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
... don't rely on cpuinfo populated in arc boot code. This paves way for
moving this code in drivers/clocksource/
And while at it, convert the WARN() to pr_warn() as sugested by Daniel
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
A standard "C" shift will be handled appropriately by the compiler
depending on the endian for the build. So we don't need the
explicit distinction in code
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC linux uses 2 distribution modes for common interrupts: round robin
mode (IDU_M_DISTRI_RR) and a simple destination mode (IDU_M_DISTRI_DEST).
The first one is used when more than 1 cores may handle a common interrupt
and the second one is used when only 1 core may handle a common interrupt.
However idu_irq_set_affinity() always sets IDU_M_DISTRI_RR for all affinity
values. But there is no sense in setting of such mode if only 1 core must
handle a common interrupt.
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This came up when reviewing code to address missing IRQ affinity
setting in AXS103 platform and/or implementing hierarchical IRQ domains
- smp_ipi_irq_setup() callers pass hwirq but in turn calls
request_percpu_irq() which expects a linux virq. So invoke
irq_find_mapping() to do the conversion
(also explicitify this in code by renaming the args appropriately)
- idu_of_init()/idu_cascade_isr() were similarly using linux virq where
hwirq is expected, so do the conversion using irqd_to_hwirq() helper
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
[vgupta: made changelog a bit concise a bit]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
For CONFIG_SERIAL_EARLYCON we need 800MHz for NPS SoC
The early console driver uses BASE_BAUD and not using dtb.
The default of 50MHz is NOT good for NPS SoC.
Signed-off-by: Noam Camus <noamca@mellanox.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The current code doesn't even compile as somehow the inline assembly
can't see the register names defined as ARC_RTC_*
I'm pretty sure It worked when I first got it merged, but the tools were
definitely different then.
So better to write this in "C" anyways.
CC: stable@vger.kernel.org #4.2+
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The original syscall only used to return errno to indicate if cmpxchg
succeeded. It was not returning the "previous" value which typical cmpxchg
callers are interested in to build their slowpaths or retry loops.
Given user preemption in syscall return path etc, it is not wise to
check this in userspace afterwards, but should be what kernel actually
observed in the syscall.
So change the syscall interface to always return the previous value and
additionally set Z flag to indicate whether operation succeeded or not
(just like ARM implementation when they used to have this syscall)
The flag approach avoids having to put_user errno which is nice given
the use case for this syscall cares mostly about the "previous" value.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
At smp_prepare_cpus() we set present cpu mask as part of init
for all CPUs at range [0-max_cpus].
This is done without checking if this mask is already being set.
At platform of eznps this mask is already being initialized at
smp_init_cpus() by using hook plat_smp_ops.init_early_smp().
So to avoid overriding of present cpu mask we check the number of
bits which are set in this mask. At the begin only bit for boot CPU
is set so if number of bits already set is no more than one we can be
assure that there is no overriding of this mask.
Signed-off-by: Noam Camus <noamca@mellanox.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Now that we have referece to section name string table in
apply_relocate_add(), use it to
- print the name of section being relocated
- print symbol with NULL name (since it refers to a section)
before
| Section to fixup 7000a060
| =========================================================
| rela->r_off | rela->addend | sym->st_value | ADDR | VALUE
| =========================================================
| 1c 0 7000e000 7000a07c 7000e000 []
| 40 0 7000a000 7000a0a0 7000a000 []
after
| Section to fixup .eh_frame @7000a060
| =========================================================
| r_off r_add st_value ADDRESS VALUE
| =========================================================
| 1c 0 7000e000 7000a07c 7000e000 [.init.text]
| 40 0 7000a000 7000a0a0 7000a000 [.exit.text]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The loop was really needed in .debug_frame regime where wanted make it
as SH_ALLOC so that apply_relocate_add() would process it. That's not
needed for .eh_frame, so we check this in apply_relocate_add() which
gets called for each section.
Note that we need to save reference to "section name strings" section in
module_frob_arch_sections() since apply_relocate_add() doesn't get that
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The motivation is to identify ARC750 vs. ARC770 (we currently print
generic "ARC700").
A given ARC700 release could be 750 or 770, with same ARCNUM (or family
identifier which is unfortunate). The existing arc_cpu_tbl[] kept a single
concatenated string for core name and release which thus doesn't work
for 750 vs. 770 identification.
So split this into 2 tables, one with core names and other with release.
And while we are at it, get rid of the range checking for family numbers.
We just document the known to exist cores running Linux and ditch
others.
With this in place, we add detection of ARC750 which is
- cores 0x33 and before
- cores 0x34 and later with MMUv2
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This came to light when helping a customer with oldish ARC750 core who
were getting instruction errors because of lack of SWAPE but boot log
was incorrectly printing it as being present
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
On older arc700 cores, some of the features configured were not present
in Build config registers. To print about them at boot, we just use the
Kconfig option i.e. whether linux is built to use them or not.
So yes this seems bogus, but what else can be done. Moreover if linux is
booting with these enabled, then the Kconfig info is a good indicator
anyways.
Over time these "hacks" accumulated in read_arc_build_cfg_regs() as well
as arc_cpu_mumbojumbo(). so refactor and move all of those in a single
place: read_arc_build_cfg_regs(). This causes some code redcution too:
| bloat-o-meter2 arch/arc/kernel/setup.o.0 arch/arc/kernel/setup.o.1
| add/remove: 0/0 grow/shrink: 2/1 up/down: 64/-132 (-68)
| function old new delta
| setup_processor 610 670 +60
| cpuinfo_arc700 76 80 +4
| arc_cpu_mumbojumbo 752 620 -132
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Previously we would not print the case when IOC existed but was not
enabled.
And while at it, reduce one line off boot printing by consolidating
the Peripheral address space and IO-Coherency which in a way
applies to them
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Older ARC700 cores (ARC750 specifically) lack instructions to implement
atomic r-w-w. This is problematic for userspace libraries such as NPTL
which need atomic primitives. So enable them by providing kernel assist.
This is costly but really the only sane soluton (othern than tight
spinning using the otherwise availiable atomic exchange EX instruciton).
Good thing is there are only a few of these cores running Linux out in
the wild.
This only works on UP systems.
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
num_possible_cpus() returns how many CPUs may be present on system.
However we want the highest possible CPU number.
This may be differ in a sparsed possible CPUs map.
Such map achived by OF for plat-eznps.
For example if we have:
possible cpus mask 0,3
Then:
num_possible_cpus() is equal 2
while
nr_cpu_ids is equal 4.
Only for value 4 c_start() will provide correct cpuinfo at procfs.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The IDU intc is technically part of MCIP (Multi-core IP) hence
historically was only available in a SMP hardware build (and thus only
in a SMP kernel build). Now that hardware restriction has been lifted,
so a UP kernel needs to support it.
This requires breaking mcip.c into parts which are strictly SMP
(inter-core interrupts) and IDU which in reality is just another
intc and thus has no bearing on SMP.
This change allows IDU in UP builds and with a suitable device tree, we
can have the cascaded intc system
ARCv2 core intc <---> ARCv2 IDU intc <---> periperals
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
When doing an nmi backtrace of many cores, most of which are idle, the
output is a little overwhelming and very uninformative. Suppress
messages for cpus that are idling when they are interrupted and just
emit one line, "NMI backtrace for N skipped: idling at pc 0xNNN".
We do this by grouping all the cpuidle code together into a new
.cpuidle.text section, and then checking the address of the interrupted
PC to see if it lies within that section.
This commit suitably tags x86 and tile idle routines, and only adds in
the minimal framework for other architectures.
Link: http://lkml.kernel.org/r/1472487169-14923-5-git-send-email-cmetcalf@mellanox.com
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org> [arm]
Tested-by: Petr Mladek <pmladek@suse.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the end of "arc_init_IRQ" STATUS32.IE flag is going to be affected by
"flag" instruction but "flag" never touches IE flag on ARCv2. So "kflag"
instruction must be used instead of "flag".
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Cc: stable@vger.kernel.org #4.2+
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
We used to keep the .exit.* sections as linker would fail in final link
due to references from .debug_frame which itself could not be discardrd
due to the forced "write,alloc" attributes for it.
| LD init/built-in.o
| `.exit.text' referenced in section `.debug_frame' of arch/arc/built-in.o: defined in discarded section `.exit.text' of arch/arc/built-in.o
| Makefile:949: recipe for target 'vmlinux' failed
With .debug_frame now retired, this hack is no longer needed.
kernel binary is now a little bit smaller as well.
closes STAR 9000549913
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This uses a new set of annoations viz. ENTRY_CFI/END_CFI to enabel cfi
ops generation.
Note that we didn't change the normal ENTRY/EXIT as we don't actually
want unwind info in the trap/exception/interrutp handlers which use
these, as unwinder then gets confused (it keeps recursing vs. stopping).
Semantically these are leaf routines and unwinding should stop when it
hits those routines.
Before
------
28.52% 1.19% 9929 hackbench libuClibc-1.0.17.so [.] __write_nocancel
|
---__write_nocancel
|--8.95%--EV_Trap
| --8.25%--sys_write
| |--3.93%--sock_write_iter
...
|--2.62%--memset <==== [LEAF entry as no unwind info]
^^^^^^
After
-----
29.46% 1.24% 13622 hackbench libuClibc-1.0.17.so [.] __write_nocancel
|
---__write_nocancel
|--9.31%--EV_Trap
| --8.62%--sys_write
| |--4.17%--sock_write_iter
...
|--6.19%--sys_write
| --6.19%--sock_write_iter
| unix_stream_sendmsg
| |--1.62%--sock_alloc_send_pskb
| |--0.89%--sock_def_readable
| |--0.88%--_raw_spin_unlock_irqrestore
| |--0.69%--memset
| | ^^^^^^ <==== [now in proper callframe]
| |
| --0.52%--skb_copy_datagram_from_iter
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This essentially removes ENTRY() assembler annotation for this symbol
since it didn't have a pairing END()
This in ahead of introducing cfi pseudo ops in ENTRY/END which expects
paired cfi_startproc/cfi_endproc
| ../arch/arc/kernel/entry.S: Assembler messages:
| ../arch/arc/kernel/entry.S:270: Error: previous CFI entry not closed (missing .cfi_endproc)
| ../scripts/Makefile.build:326: recipe for target 'arch/arc/kernel/entry-arcv2.o' failed
| make[4]: *** [arch/arc/kernel/entry-arcv2.o] Error 1
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
So finally after almost 8 years of dealing with .debug_frame, we are
finally switching to .eh_frame. The reason being stripped kernel
binaries had non-functional unwinder as .debug_frame was gone.
Also, in general .eh_frame seems more common way of doing unwinding.
This also folds a revert of f52e126cc7 ("ARC: unwind: ensure that
.debug_frame is generated (vs. .eh_frame)") to ensure that we start
getting .eh_frame
Reported-by: Daniel Mentz <danielmentz@google.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
We used to live with PERF_COUNT_HW_CACHE_REFERENCES and
PERF_COUNT_HW_CACHE_REFERENCES not specified on ARC.
Those events are actually aliases to 2 cache events that we do support
and so this change sets "cache-reference" and "cache-misses" events
in the same way as "L1-dcache-loads" and L1-dcache-load-misses.
And while at it adding debug info for cache events as well as doing a
subtle fix in HW events debug info - config value is much better
represented by hex so we may see not only event index but as well other
control bits set (if they exist).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-snps-arc@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
HS release 3.0 provides for even more flexibility in specifying the
volatile address space for mapping peripherals.
With HS 2.1 @start was made flexible / programmable - with HS 3.0 even
@end can be setup (vs. fixed to 0xFFFF_FFFF before).
So add code to reflect that and while at it remove an unused struct
defintion
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
On faulting sigreturn we do get SIGSEGV, all right, but anything
we'd put into pt_regs could end up in the coredump. And since
__copy_from_user() never zeroed on arc, we'd better bugger off
on its failure without copying random uninitialized bits of
kernel stack into pt_regs...
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Some module using div_u64() was failing to link because the libgcc 64-bit
divide assist routine was not being exported for modules
Reported-by: avinashp@quantenna.com
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The syscall ABI includes the gcc functional calling ABI since a syscall
implies userland caller and kernel callee.
The current gcc ABI (v3) for ARCv2 ISA required 64-bit data be passed in
even-odd register pairs, (potentially punching reg holes when passing such
values as args). This was partly driven by the fact that the double-word
LDD/STD instructions in ARCv2 expect the register alignment and thus gcc
forcing this avoids extra MOV at the cost of a few unused register (which we
have plenty anyways).
This however was rejected as part of upstreaming gcc port to HS. So the new
ABI v4 doesn't enforce the even-odd reg restriction.
Do note that for ARCompact ISA builds v3 and v4 are practically the same in
terms of gcc code generation.
In terms of change management, we infer the new ABI if gcc 6.x onwards
is used for building the kernel.
This also needs a stable backport to enable older kernels to work with
new tools/user-space
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- Removal of most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to call
it if they have special needs.
- Use pr_fmt on all the DT core print statements.
- CoreSight binding doc improvements to block name descriptions.
- Add dt_to_config script which can parse dts files and list
corresponding kernel config options.
- Fix memory leak hit with a PowerMac DT.
- Correct a bunch of STMicro compatible strings to use the correct
vendor prefix.
- Fix DA9052 PMIC binding doc to match what is actually used in dts
files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wLMr
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- remove most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to
call it if they have special needs
- use pr_fmt on all the DT core print statements
- CoreSight binding doc improvements to block name descriptions
- add dt_to_config script which can parse dts files and list
corresponding kernel config options
- fix memory leak hit with a PowerMac DT
- correct a bunch of STMicro compatible strings to use the correct
vendor prefix
- fix DA9052 PMIC binding doc to match what is actually used in dts
files
* tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
documentation: da9052: Update regulator bindings names to match DA9052/53 DTS expectations
xtensa: Partially Revert "xtensa: Remove unnecessary of_platform_populate with default match table"
xtensa: Fix build error due to missing include file
MIPS: ath79: Add missing include file
Fix spelling errors in Documentation/devicetree
ARM: dts: fix STMicroelectronics compatible strings
powerpc/dts: fix STMicroelectronics compatible strings
Documentation: dt: i2c: use correct STMicroelectronics vendor prefix
scripts/dtc: dt_to_config - kernel config options for a devicetree
of: fdt: mark unflattened tree as detached
of: overlay: add resolver error prints
coresight: document binding acronyms
Documentation/devicetree: document cavium-pip rx-delay/tx-delay properties
of: use pr_fmt prefix for all console printing
of/irq: Mark initialised interrupt controllers as populated
of: fix memory leak related to safe_name()
Revert "of/platform: export of_default_bus_match_table"
of: unittest: use of_platform_default_populate() to populate default bus
memory: omap-gpmc: use of_platform_default_populate() to populate default bus
bus: uniphier-system-bus: use of_platform_default_populate() to populate default bus
...
Pull smp hotplug updates from Thomas Gleixner:
"This is the next part of the hotplug rework.
- Convert all notifiers with a priority assigned
- Convert all CPU_STARTING/DYING notifiers
The final removal of the STARTING/DYING infrastructure will happen
when the merge window closes.
Another 700 hundred line of unpenetrable maze gone :)"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
timers/core: Correct callback order during CPU hot plug
leds/trigger/cpu: Move from CPU_STARTING to ONLINE level
powerpc/numa: Convert to hotplug state machine
arm/perf: Fix hotplug state machine conversion
irqchip/armada: Avoid unused function warnings
ARC/time: Convert to hotplug state machine
clocksource/atlas7: Convert to hotplug state machine
clocksource/armada-370-xp: Convert to hotplug state machine
clocksource/exynos_mct: Convert to hotplug state machine
clocksource/arm_global_timer: Convert to hotplug state machine
rcu: Convert rcutree to hotplug state machine
KVM/arm/arm64/vgic-new: Convert to hotplug state machine
smp/cfd: Convert core to hotplug state machine
x86/x2apic: Convert to CPU hotplug state machine
profile: Convert to hotplug state machine
timers/core: Convert to hotplug state machine
hrtimer: Convert to hotplug state machine
x86/tboot: Convert to hotplug state machine
arm64/armv8 deprecated: Convert to hotplug state machine
hwtracing/coresight-etm4x: Convert to hotplug state machine
...
Things have been calm here - nothing much except for a few fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/rhI
-----END PGP SIGNATURE-----
Merge tag 'arc-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"Things have been calm here - nothing much except for a few fixes"
* tag 'arc-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: mm: don't loose PTE_SPECIAL in pte_modify()
ARC: dma: fix address translation in arc_dma_free
ARC: typo fix in mm/ioremap.c
ARC: fix linux-next build breakage
Pull the clockevents/clocksource tree from Daniel Lezcano:
- Convert the clocksource-probe init functions to return a value in order to
prepare the consolidation of the drivers using the DT. It is a big patchset
but went through 01.org (kbuild bot), linux next and kernel-ci (continuous
integration) (Daniel Lezcano)
- Fix a bad error handling by returning the right value for cadence_ttc
(Christophe Jaillet)
- Fix typo in the Kconfig for the Samsung pwm (Alexandre Belloni)
- Change functions to static for armada-370-xp and digicolor (Ben Dooks)
- Add support for the rk3399 SoC timer by adding bindings and a slight
change in the base address. Take the opportunity to add the DYNIRQ flag
(Huang Tao)
- Fix endian accessors for the Samsung pwm timer (Matthew Leach)
- Add Oxford Semiconductor RPS Dual Timer driver (Neil Armstrong)
- Add a kernel parameter to swich on/off the event stream feature of the arch
arm timer (Will Deacon)
All the clocksource drivers's init function are now converted to return
an error code. CLOCKSOURCE_OF_DECLARE is no longer used as well as the
clksrc-of table.
Let's convert back the names:
- CLOCKSOURCE_OF_DECLARE_RET => CLOCKSOURCE_OF_DECLARE
- clksrc-of-ret => clksrc-of
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
For exynos_mct and samsung_pwm_timer:
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
For arch/arc:
Acked-by: Vineet Gupta <vgupta@synopsys.com>
For mediatek driver:
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
For the Rockchip-part
Acked-by: Heiko Stuebner <heiko@sntech.de>
For STi :
Acked-by: Patrice Chotard <patrice.chotard@st.com>
For the mps2-timer.c and versatile.c changes:
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
For the OXNAS part :
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
For LPC32xx driver:
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
For Broadcom Kona timer change:
Acked-by: Ray Jui <ray.jui@broadcom.com>
For Sun4i and Sun5i:
Acked-by: Chen-Yu Tsai <wens@csie.org>
For Meson6:
Acked-by: Carlo Caione <carlo@caione.org>
For Keystone:
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
For NPS:
Acked-by: Noam Camus <noamca@mellanox.com>
For bcm2835:
Acked-by: Eric Anholt <eric@anholt.net>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
If CONFIG_ARC_DW2_UNWIND is disabled every time arc_unwind_core()
gets called following message gets printed in debug console:
----------------->8---------------
CONFIG_ARC_DW2_UNWIND needs to be enabled
----------------->8---------------
That message makes sense if user indeed wants to see a backtrace or
get nice function call-graphs in perf but what if user disabled
unwinder for the purpose? Why pollute his debug console?
So instead we'll warn user about possibly missing feature once and
let him decide if that was what he or she really wanted.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
After patch "of/platform: Add common method to populate default bus",
it is possible for arch code to remove unnecessary callers of
of_platform_populate with default match table.
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Rob Herring <robh@kernel.org>
ARC700 support for 2 interrupt priorities historically allowed even slow
perpherals such as emac and uart to setup high priority interrupts
which was wrong from the beginning as they could possibly delay the more
critical timer interrupt.
The hardware support for 2 level interrupts in ARCompact is less than
ideal anyways (judging from the "hacks" in low level entry code and thus
is not used in productions systems I know of.
So reduce the scope of this to timer only, thereby reducing a bunch of
complexity.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Vineet Gupta