This was found only after the whole thing with the inline functions, but
the compiler actually found something. The value of the `bias` (in
adis16480_get_calibbias()) should only be set if the read operation was
successful.
No actual known problem occurs as users of this function all
ultimately check the return value. Hence probably not stable material.
Fixes: 2f3abe6cbb ("iio:imu: Add support for the ADIS16480 and similar IMUs")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is a typical checkpatch warning. The change just renames the type of
the `freq` var to `unsigned int`.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is just a minor indentation/alignment fix for the default case of a
switch statement.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS library functions return zero on success, and negative values for
error. Positive values aren't returned, but we only care about the success
value (which is zero).
This change is mostly needed so that the compiler won't make any inferences
about some about values being potentially un-initialized. This only
triggers after making some functions inline, because the compiler can
better follow return paths.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS library functions return zero on success, and negative values for
error. Positive values aren't returned, but we only care about the success
value (which is zero).
This change is mostly needed so that the compiler won't make any inferences
about some about values being potentially un-initialized. This only
triggers after making some functions inline, because the compiler can
better follow return paths.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS library functions return zero on success, and negative values for
error. Positive values aren't returned, but we only care about the success
value (which is zero).
This change is mostly needed so that the compiler won't make any inferences
about some about values being potentially un-initialized. This only
triggers after making some functions inline, because the compiler can
better follow return paths.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS library functions return zero on success, and negative values for
error. Positive values aren't returned, but we only care about the success
value (which is zero).
This change is mostly needed so that the compiler won't make any inferences
about some about values being potentially un-initialized. This only
triggers after making some functions inline, because the compiler can
better follow return paths.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS library functions return zero on success, and negative values for
error. Positive values aren't returned, but we only care about the success
value (which is zero).
This change is mostly needed so that the compiler won't make any inferences
about some about values being potentially un-initialized. This only
triggers after making some functions inline, because the compiler can
better follow return paths.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_postenable() hook should be called first to
attach the poll function and the iio_triggered_buffer_predisable() hook
should be called last in the predisable hook.
This change updates the driver to attach/detach the poll func in the
correct order.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_postenable() hook should be called first to
attach the poll function. The iio_triggered_buffer_predisable() hook is
called last (as is it should).
This change moves iio_triggered_buffer_postenable() to be called first. It
adds iio_triggered_buffer_predisable() on the error paths of the postenable
hook.
For the predisable hook, some code-paths have been changed to make sure
that the iio_triggered_buffer_predisable() hook gets called in case there
is an error before it.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM LSM6DSRX 6-axis (acc + gyro) Mems sensor
https://www.st.com/resource/en/datasheet/lsm6dsrx.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There maybe a race when using dmaengine_terminate_all(). The predisable
routine may call iio_triggered_buffer_predisable() prior to a pending DMA
callback.
Adopt dmaengine_terminate_sync() to ensure there's no pending DMA request
before calling iio_triggered_buffer_predisable().
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
None of the ST sensor drivers use any symbols from
<linux/gpio.h>, just drop the include from all of them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .ioctl and .compat_ioctl file operations have the same prototype so
they can both point to the same function, which works great almost all
the time when all the commands are compatible.
One exception is the s390 architecture, where a compat pointer is only
31 bit wide, and converting it into a 64-bit pointer requires calling
compat_ptr(). Most drivers here will never run in s390, but since we now
have a generic helper for it, it's easy enough to use it consistently.
I double-checked all these drivers to ensure that all ioctl arguments
are used as pointers or are ignored, but are not interpreted as integer
values.
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Darren Hart (VMware) <dvhart@infradead.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Set gain in hx711_reset() to its default value after a reset cycle. This
omits one precautionary read cycle, because the read is performed in
hx711_set_gain_for_channel() anyway if gain has changed.
Check for DOUT low and if its high wait some time if it goes down
instead of doing a blind reset cycle when DOUT is not down.
This is a performance optimization which allows to query the sensor with
a higher frequency.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix the following warnings when documentation is built:
drivers/iio/adc/stm32-adc-core.c:62: warning: cannot understand function
prototype: 'struct stm32_adc_common_regs '
drivers/iio/adc/stm32-adc-core.c:78: warning: cannot understand function
prototype: 'struct stm32_adc_priv_cfg '
drivers/iio/adc/stm32-adc-core.c:123: warning: Function parameter or
member 'pdev' not described in 'stm32f4_adc_clk_sel'
drivers/iio/adc/stm32-adc.c:219: warning: cannot understand function
prototype: 'struct stm32_adc_regs '
drivers/iio/adc/stm32-adc.c:237: warning: cannot understand function
prototype: 'struct stm32_adc_regspec '
drivers/iio/adc/stm32-adc.c:264: warning: cannot understand function
prototype: 'struct stm32_adc_cfg '
drivers/iio/adc/stm32-adc.c:323: warning: Function parameter or member
'difsel' not described in 'N'
drivers/iio/adc/stm32-adc.c:323: warning: Function parameter or member
'pcsel' not described in 'stm32_adc'
drivers/iio/adc/stm32-adc.c:371: warning: cannot understand function
prototype: 'const struct stm32_adc_regs stm32f4_sq[STM32_ADC_MAX_SQ + 1]
drivers/iio/adc/stm32-adc.c:417: warning: cannot understand function
prototype: 'const struct stm32_adc_regs stm32f4_smp_bits[] = '
drivers/iio/adc/stm32-adc.c:508: warning: cannot understand function
prototype: 'const struct stm32_adc_regs stm32h7_smp_bits[] = '
drivers/iio/adc/stm32-adc.c:1112: warning: Function parameter or member
'indio_dev' not described in 'stm32_adc_get_trig_extsel'
drivers/iio/adc/stm32-adc.c:1420: warning: Function parameter or member
'indio_dev' not described in 'stm32_adc_debugfs_reg_access'
drivers/iio/adc/stm32-adc.c:1420: warning: Function parameter or member
'reg' not described in 'stm32_adc_debugfs_reg_access'
drivers/iio/adc/stm32-adc.c:1420: warning: Function parameter or member
'writeval' not described in 'stm32_adc_debugfs_reg_access'
drivers/iio/adc/stm32-adc.c:1420: warning: Function parameter or member
'readval' not described in 'stm32_adc_debugfs_reg_access'
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_{predisable,postenable} functions attach/detach
the poll functions.
The iio_triggered_buffer_postenable() should be called before (to attach
the poll func) and then the
The iio_triggered_buffer_predisable() function is hooked directly without
anything, which is probably fine, as the postenable() version seems to also
do some reset/wake-up of the device.
This will mean it will be easier when removing it; i.e. it just gets
removed.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some chips have a fifo overflow bit issue where the bit is always
set. The result is that every data is dropped.
Change fifo overflow management by checking fifo count against
a maximum value.
Add fifo size in chip hardware set of values.
Fixes: f5057e7b2d ("iio: imu: inv_mpu6050: better fifo overflow handling")
Cc: stable@vger.kernel.org
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Suggestion from coccinelle / coccicheck
CHECK drivers/iio/adc/twl4030-madc.c
drivers/iio/adc/twl4030-madc.c:524:6-15: WARNING: Comparison of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:655:1-43: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:659:2-44: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:664:1-43: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:498:2-34: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:510:2-19: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:511:2-11: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:531:2-19: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:532:2-11: WARNING: Assignment of 0/1 to bool variable
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
The LTC2983 is a Multi-Sensor High Accuracy Digital Temperature
Measurement System. It measures a wide variety of temperature sensors and
digitally outputs the result, in °C or °F, with 0.1°C accuracy and
0.001°C resolution. It can measure the temperature of all standard
thermocouples (type B,E,J,K,N,S,R,T), standard 2-,3-,4-wire RTDs,
thermistors and diodes.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We can drop some duplicate code if we use devm_action for disabling
regulators and pm and the managed variant of iio_device_register().
This allows us to completely remove all remove() callbacks from both
i2c and spi code.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The vddd and vdda supplies are always operated on together. We can
shrink the code a bit by using the bulk regulator helpers.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
FXOS8700CQ is a small, low-power, 3-axis linear accelerometer and 3-axis
magnetometer combined into a single package. The device features a
selectable I2C or point-to-point SPI serial interface with 14-bit
accelerometer and 16-bit magnetometer ADC resolution along with
smart-embedded functions.
FXOS8700CQ has dynamically selectable accelerationfull-scale ranges of
±2 g/±4 g/±8 g and a fixed magnetic measurement range of ±1200 μT.
Output data rates (ODR) from 1.563 Hz to 800 Hz are selectable by the user
for each sensor. Interleaved magnetic and acceleration data is available
at ODR rates of up to 400 Hz. FXOS8700CQ is available in a plastic QFN
package and it is guaranteed to operate over the extended temperature
range of –40 °C to +85 °C.
TODO: Trigger and IRQ configuration support
Datasheet:
http://cache.freescale.com/files/sensors/doc/data_sheet/FXOS8700CQ.pdf
Signed-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reduces local boilerplate.
Suggested by coccinelle.
CHECK drivers/iio/adc/xilinx-xadc-core.c
drivers/iio/adc/xilinx-xadc-core.c:1184:1-11: WARNING: Use devm_platform_ioremap_resource for xadc -> base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Manish Narani <manish.narani@xilinx.com>
Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com>
Coccinelle noticed:
CHECK drivers/iio/adc/cpcap-adc.c
drivers/iio/adc/cpcap-adc.c:1009:9-34: ERROR: Threaded IRQ with no primary handler requested without IRQF_ONESHOT
As far as I can see this is a simple case of it should be specified
but isn't.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Avoid local boilerplate.
Suggested by coccinelle via coccicheck.
CHECK drivers/iio/adc/meson_saradc.c
drivers/iio/adc/meson_saradc.c:1218:1-5: WARNING: Use devm_platform_ioremap_resource for base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reduce local boilerplate.
Identified by coccinelle
drivers/iio/adc/exynos_adc.c:792:1-11: WARNING: Use devm_platform_ioremap_resource for info -> regs
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Sparse identified the following
CHECK drivers/iio/proximity/pulsedlight-lidar-lite-v2.c
drivers/iio/proximity/pulsedlight-lidar-lite-v2.c:144:24: warning: cast to restricted __be16
drivers/iio/proximity/pulsedlight-lidar-lite-v2.c:144:24: warning: cast to restricted __be16
drivers/iio/proximity/pulsedlight-lidar-lite-v2.c:144:24: warning: cast to restricted __be16
drivers/iio/proximity/pulsedlight-lidar-lite-v2.c:144:24: warning: cast to restricted __be16
This cleans up by adding a local variable to hold the value whilst
it is __be16 before applying endian converstion into eventual destination.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
There is a somewhat interesting mixture of be16 and le16 going on in
this one function. Changes here formalize that a little more.
CHECK drivers/iio/pressure/bmp280-core.c
drivers/iio/pressure/bmp280-core.c:215:35: warning: cast to restricted __le16
drivers/iio/pressure/bmp280-core.c:229:37: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:229:37: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:229:37: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:229:37: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:230:36: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:230:36: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:230:36: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:230:36: warning: cast to restricted __be16
drivers/iio/pressure/bmp280-core.c:237:37: warning: cast to restricted __le16
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
This clearly has no actual affect but it does show sparse and similar
static analysers that we are doing this intentionally.
CHECK drivers/iio/gyro/mpu3050-core.c
drivers/iio/gyro/mpu3050-core.c:546:48: warning: incorrect type in assignment (different base types)
drivers/iio/gyro/mpu3050-core.c:546:48: expected restricted __be16 <noident>
drivers/iio/gyro/mpu3050-core.c:546:48: got int
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
When breaking up a constant to write to two 8 bit registers
it isn't obvious to sparse that it was intentional.
CHECK drivers/iio/chemical/sps30.c
drivers/iio/chemical/sps30.c:120:30: warning: cast truncates bits from constant value (8004 becomes 4)
So in the interests of minimising noisy warnings, let us add
a mask.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Tomasz Duszynski <tduszyns@gmail.com>
Nothing stops data being of type __be16, which fixes the warning:
CHECK drivers/iio/adc/stmpe-adc.c
drivers/iio/adc/stmpe-adc.c:202:29: warning: cast to restricted __be16
drivers/iio/adc/stmpe-adc.c:202:29: warning: cast to restricted __be16
drivers/iio/adc/stmpe-adc.c:202:29: warning: cast to restricted __be16
drivers/iio/adc/stmpe-adc.c:202:29: warning: cast to restricted __be16
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: <philippe.schenker@toradex.com>
Cleans up the sparse warning:
CHECK drivers/iio/adc/at91-sama5d2_adc.c
drivers/iio/adc/at91-sama5d2_adc.c:1486:31: warning: Using plain integer as NULL pointer
drivers/iio/adc/at91-sama5d2_adc.c:1509:31: warning: Using plain integer as NULL pointer
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
This is a new driver for the ST-Ericsson AB8500 GPADC, which
replaces the old driver in drivers/mfd/ab8500-gpadc.c and
thus gets rid of another necessarily different custom driver
from the times before IIO existed.
The AB8500 GPADC can convert 10 different channels and these
are used for monitoring voltages in the U8500 chipset, some
are used for battery charging, some for temperature
monitoring.
As this is very core functionality that a lot of drivers
depend on and was formerly compiled in with the AB8500 core
driver, we deafault it to 'y' in Kconfig: it can be compiled
out but it is really not advisible: the platform can
for example overheat if we do.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Exposes the ADC device present on, at least, Intel Merrifield platform.
Based on work done by:
Yang Bin <bin.yang@intel.com>
Huiquan Zhong <huiquan.zhong@intel.com>
Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Pavan Kumar S <pavan.kumar.s@intel.com>
Though it has been heavily rewritten for upstream.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM LSM6DS0 6-axis (acc + gyro) Mems sensor
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix typos in gyro gain definitions for LSM9DS1 sensor
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change replaces indio_dev's mlock with the driver's own lock. The lock
is mostly needed to protect state when changing the `dac_cache` info.
The lock has been extended to `ad7303_read_raw()`, to make sure that the
cache is updated if an SPI-write is already in progress.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On LSM6DSO/LSM6DSR/LSM6DSOX/ASM330LHH and ISH330DHCX
devices it is possible to trim the hardware timestamp
resolution through the FREQ_FINE[7:0] bits of the
INTERNAL_FREQ_FINE register, which contains the difference
in percentage of the effective ODR (and timestamp rate)
with respect to the typical value.
The formula for calculating the effective ODR reported
in the application notes has been linearized to the first
order to simplify the calculation (pls. see note on source
code).
This change may be useful in the outcome of CTS
tests regarding the SingleSensorTests and the
SensorTest#testSensorTimeStamps for high ODRs
Signed-off-by: Mario Tesi <mario.tesi@st.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable drdy mask if available in order to mark invalid samples during
sensor bootstrap phase
Tested-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for runtime PM & sleep.
Provide pclk to regmap as registers access doesn't need full power
(e.g. regulator). Always restore HFSEL when resuming. It may get lost
depending on low power level that has been achieved.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add missing wake-up register info for LSM6DSO/LSM6DSOX sensor
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add missing kernel doc for st_lsm6dsx_hw data structure
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add the possibility to enable/disable wakeup source through
st_sensors_platform_data and not only through device tree
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix following checkpatch warnings:
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_read_event(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_write_event(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_read_event_config(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_write_event_config(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
WARNING: line over 80 characters
+ if (dev->of_node && of_property_read_bool(dev->of_node, "wakeup-source"))
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Always grub conf mutex in st_lsm6dsx_write_event_config since it can run
concurrently with FIFO configuration
Fixes: b5969abfa8 ("iio: imu: st_lsm6dsx: add motion events")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rely on st_lsm6dsx_update_bits_locked in st_lsm6dsx_write_event and
st_lsm6dsx_event_setup routines since they can run concurrently with
sensor hub configuration
Fixes: b5969abfa8 ("iio: imu: st_lsm6dsx: add motion events")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check if enable_reg of event_settings data structure is defined before
writing on it
Fixes: b5969abfa8 ("iio: imu: st_lsm6dsx: add motion events")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move bdu, boot and reset register definitions in hw_settings register
map since not all supported sensors (e.g lsm9ds1) rely on the same
definitions
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move active low and open drain register definitions in hw_settings
register map since not all supported sensors (e.g lsm9ds1) rely on the
same definitions
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Group irq related definition in irq_config structure in
st_lsm6dsx_settings. This is a preliminary patch to move
OpenDrain/Active low registers in st_lsm6dsx_settings.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check read_fifo pointer before using it since we can't assume it
is always set adding new sensors. This patch fixes the following crash:
irq 277: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.0-rc5-00322-g792b824-dirty #7
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[<c0112750>] (unwind_backtrace) from [<c010d018>] (show_stack+0x10/0x14)
[<c010d018>] (show_stack) from [<c0c2bfc8>] (dump_stack+0xd8/0x10c)
[<c0c2bfc8>] (dump_stack) from [<c01923fc>] (__report_bad_irq+0x24/0xc0)
[<c01923fc>] (__report_bad_irq) from [<c0192820>] (note_interrupt+0x27c/0x2dc)
[<c0192820>] (note_interrupt) from [<c018f174>] (handle_irq_event_percpu+0x54/0x7c)
[<c018f174>] (handle_irq_event_percpu) from [<c018f1d4>] (handle_irq_event+0x38/0x5c)
[<c018f1d4>] (handle_irq_event) from [<c0193664>] (handle_level_irq+0xc8/0x154)
[<c0193664>] (handle_level_irq) from [<c018df58>] (generic_handle_irq+0x20/0x34)
[<c018df58>] (generic_handle_irq) from [<c053c348>] (mxc_gpio_irq_handler+0xc4/0xf8)
[<c053c348>] (mxc_gpio_irq_handler) from [<c053c3e0>] (mx3_gpio_irq_handler+0x64/0xb8)
[<c053c3e0>] (mx3_gpio_irq_handler) from [<c018df58>] (generic_handle_irq+0x20/0x34)
[<c018df58>] (generic_handle_irq) from [<c018e550>] (__handle_domain_irq+0x64/0xe0)
[<c018e550>] (__handle_domain_irq) from [<c0529610>] (gic_handle_irq+0x4c/0xa0)
[<c0529610>] (gic_handle_irq) from [<c0101a70>] (__irq_svc+0x70/0x98)
Exception stack(0xc1301f10 to 0xc1301f58
1f00: 00000001 00000006 00000000 c130c340
1f20: c1300000 c1308928 00000001 c1308960 00000000 c12b9db0 c1308908 00000000
1f40: 00000000 c1301f60 c0182010 c0109508 20000013 ffffffff
[<c0101a70>] (__irq_svc) from [<c0109508>] (arch_cpu_idle+0x20/0x3c)
[<c0109508>] (arch_cpu_idle) from [<c015ed70>] (do_idle+0x1bc/0x2bc)
[<c015ed70>] (do_idle) from [<c015f204>] (cpu_startup_entry+0x18/0x1c)
[<c015f204>] (cpu_startup_entry) from [<c1200e68>] (start_kernel+0x440/0x504)
[<c1200e68>] (start_kernel) from [<00000000>] (0x0)
handlers:
[<62052c0d>] st_lsm6dsx_handler_irq threaded
[<f2004b92>] st_lsm6dsx_handler_thread
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Tested-by: Bobby Jones <rjones@gateworks.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rely on st_lsm6dsx_read_locked in st_lsm6dsx_report_motion_event since
it can run concurrently with sensor hub configuration. Move event
related code in st_lsm6dsx_report_motion_event
Fixes: 1aabad1fb5 ("iio: imu: st_lsm6dsx: add motion report function and call from interrupt")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Maxim's max12xx series is very similar to the max10xx series, with the
difference of the measurements depth which is upgraded from 10 to 12
bits per channel. Everything else looks the same.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Maxim's max1027/29/31 series returns the measured voltages with a
resolution of 10 bits. There is a very similar series, max1227/29/31
which works identically but uses a resolution of 12 bits. Prepare the
support for these chips by turning the 'depth' into a macro parameter
instead of hardcoding it everywhere. Also reorganize just a bit the
macros at the top to avoid repeating tens of lines when adding support
for a new chip.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All the registers are configured by the driver, let's reset the chip
at probe time, avoiding any conflict with a possible earlier
configuration.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The chip has a 'start conversion' and a 'end of conversion' pair of
pins. They can be used but this is absolutely not mandatory as regular
polling of the value is totally fine with the current internal
clocking setup. Turn the interrupts optional and do not error out if
they are not inquired in the device tree. This has the effect to
prevent triggered buffers use though.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Until now, only write operations were supported. Force two bytes read
operation when reading, which should fit most of the development
purposes. Of course, extended operations like buffered reads on
multiple channels or even temperature + voltage reads will not be read
entirely. Usually, just starting a new operation will work but in any
case a software reset (done through the debufs interface too) will
return the device in a usable state.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add initial support for Analog Devices ADUX1020 Photometric sensor.
Only proximity mode has been enabled for now.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since the logic for `spi_delay` struct + `spi_delay_exec()` has been copied
from the `cs_change_delay` logic, it's natural to make this delay, the
first user.
The `cs_change_delay` logic requires that the default remain 10 uS, in case
it is unspecified/unconfigured. So, there is some special handling needed
to do that.
The ADIS library is one of the few users of the new `cs_change_delay`
parameter for an spi_transfer.
The introduction of the `spi_delay` struct, requires that the users of of
`cs_change_delay` get an update. This change also updates the ADIS library.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-4-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Third version with the adis rework set dropped as better to just have
a fresh version of that at some future date.
The usual mixed backs of new device support being added to drivers,
long term reworks continuing and little per driver cleanups and
features.
Also a few trivial counter subsystem tidy ups on behalf of William.
Core new feature
* Device label support. A long requested feature no one got around to
implementing before. Allows DT based provision of a 'label' that
identifies a device uniquely within a system. This differs from existing
'name' which is meant to be the part number.
New device support
* ingenic-adc
- Support for the JZ4770 SoC ADC including bindings.
* inv_mpu6050
- Add support for magnetometer in MPU925x parts.
Fiddly to do as this is actually a separate device sitting inside the
package, but with the master device being able to schedule reads etc.
Will only run if the auxiliary bus is not in use for any other devices.
Features
* ad7192
- Userspace calibration controls to do zero and full scale.
* st_lsm6dsx
- Enable latched interrupts by default for sensors events with related clear.
- Motion events and related wakeup source. This needed quite a bit of
refactoring as well.
Cleanups and minor features
* ad7192
- sysfs ABI docs
* ad7949
- Remove code to readback configuration word as driver never actually enabled
it.
- Fix incorrect xfer length. Not actually known to cause problems other
than wasted bus usage.
* adis16080
- Replace core mlock usage with local lock with more appropriate scope.
* adis16130
- Remove pointless mlock usage.
* adis16240
- Remove include of gpio.h as no gpio usage.
* atlas-ph-sensor
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* bh1750
- Fix up a static compiler warning and make the code more readable.
- yaml conversion of binding + MAINTAINERS entry.
* bmp280
- Drop a stray newline.
* cm36651
- Drop a redundant assignment
* itg3200
- Alignment cleanup.
* max31856
- Add missing of_node and parent references, useful to identify the device.
* sc27xx_adc
- Use devm_hwspin_lock_request_specific rather than local rolled version.
* stm32-lptimer counter
- kernel-doc warning.
* stm32-timer counter
- kernel-doc warning.
- Alignment cleanup.
* sx9500
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* tcs3414
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
-----BEGIN PGP SIGNATURE-----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=nIWU
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.5a-take3' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of IIO new device support, cleanups and features for the 5.5 cycle
Third version with the adis rework set dropped as better to just have
a fresh version of that at some future date.
The usual mixed backs of new device support being added to drivers,
long term reworks continuing and little per driver cleanups and
features.
Also a few trivial counter subsystem tidy ups on behalf of William.
Core new feature
* Device label support. A long requested feature no one got around to
implementing before. Allows DT based provision of a 'label' that
identifies a device uniquely within a system. This differs from existing
'name' which is meant to be the part number.
New device support
* ingenic-adc
- Support for the JZ4770 SoC ADC including bindings.
* inv_mpu6050
- Add support for magnetometer in MPU925x parts.
Fiddly to do as this is actually a separate device sitting inside the
package, but with the master device being able to schedule reads etc.
Will only run if the auxiliary bus is not in use for any other devices.
Features
* ad7192
- Userspace calibration controls to do zero and full scale.
* st_lsm6dsx
- Enable latched interrupts by default for sensors events with related clear.
- Motion events and related wakeup source. This needed quite a bit of
refactoring as well.
Cleanups and minor features
* ad7192
- sysfs ABI docs
* ad7949
- Remove code to readback configuration word as driver never actually enabled
it.
- Fix incorrect xfer length. Not actually known to cause problems other
than wasted bus usage.
* adis16080
- Replace core mlock usage with local lock with more appropriate scope.
* adis16130
- Remove pointless mlock usage.
* adis16240
- Remove include of gpio.h as no gpio usage.
* atlas-ph-sensor
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* bh1750
- Fix up a static compiler warning and make the code more readable.
- yaml conversion of binding + MAINTAINERS entry.
* bmp280
- Drop a stray newline.
* cm36651
- Drop a redundant assignment
* itg3200
- Alignment cleanup.
* max31856
- Add missing of_node and parent references, useful to identify the device.
* sc27xx_adc
- Use devm_hwspin_lock_request_specific rather than local rolled version.
* stm32-lptimer counter
- kernel-doc warning.
* stm32-timer counter
- kernel-doc warning.
- Alignment cleanup.
* sx9500
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* tcs3414
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* tag 'iio-for-5.5a-take3' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (41 commits)
iio: pressure: bmp280: remove stray newline
iio: adc: sc27xx: Use devm_hwspin_lock_request_specific() to simplify code
iio: chemical: atlas-ph-sensor: fix iio_triggered_buffer_predisable() position
iio: gyro: clean up indentation issue
counter: stm32: clean up indentation issue
iio: proximity: sx9500: fix iio_triggered_buffer_{predisable,postenable} positions
iio: core: Add optional symbolic label to device attributes
dt-binding: iio: Add optional label property
iio: gyro: adis16080: replace mlock with own lock
counter: stm32-lptimer-cnt: fix a kernel-doc warning
counter: stm32-timer-cnt: fix a kernel-doc warning
iio: gyro: adis16130: remove mlock usage
MAINTAINERS: add entry for ROHM BH1750 driver
dt-bindings: iio: light: bh1750: convert bindings to yaml
iio: imu: st_lsm6dsx: add motion report function and call from interrupt
iio: imu: st_lsm6dsx: always enter interrupt thread
iio: imu: st_lsm6dsx: add wakeup-source option
iio: imu: st_lsm6dsx: add motion events
iio: imu: st_lsm6dsx: move interrupt thread to core
iio: imu: inv_mpu6050: add fifo support for magnetometer data
...
Remove a stray newline from the probe callback.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Change to use devm_hwspin_lock_request_specific() to help to simplify the
cleanup code for drivers requesting one hwlock.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_{predisable,postenable} functions attach/detach
the poll functions.
The iio_triggered_buffer_predisable() should be called last, to detach the
poll func after the devices has been suspended.
The position of iio_triggered_buffer_postenable() is correct.
Note this is not stable material. It's a fix in the logical
model rather fixing an actual bug. These are being tidied up
throughout the subsystem to allow more substantial rework that
was blocked by variations in how things were done.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The measured time value in the driver is limited to the maximum distance
which can be read by the sensor. This limitation was wrong and is fixed
by this patch.
It also takes into account that we are supporting a variety of sensors
today and that the recently added sensors have a higher maximum
distance range.
Changes in v2:
- Added a Tested-by
Suggested-by: Zbyněk Kocur <zbynek.kocur@fel.cvut.cz>
Tested-by: Zbyněk Kocur <zbynek.kocur@fel.cvut.cz>
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Cc:<Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It could happen that either `val` or `val2` [provided from userspace] is
negative. In that case the computed frequency could get a weird value.
Fix this by checking that neither of the 2 variables is negative, and check
that the computed result is not-zero.
Fixes: e4f9593901 ("iio: imu: adis16480 switch sampling frequency attr to core support")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* adis16400
- Make sure to free memory on a few failure paths.
* adxl372
- Fix wrong fifo depth
- Fix wrong indexing of data from the fifo.
- Perform a reset at startup to avoid a problem with inconsistent state.
* axp288
- This is a fix for a fix. The original fix made sure we kept the
configuration from some firmwares to preserve a bias current.
Unfortunately it appears the previous behaviour was working around
a buggy firmware by overwriting the wrong value it had. Hence
a regression was seen.
* bmc150
- Fix the centre temperature. This was due to an error in one of the
datasheets.
* hx711
- Fix an issue where a badly timed interrupt could lead to a control
line being high long enough to put the device into a low power state.
* meson_sar_adc
- Fix a case where the irq was enabled before everything it uses was
allocated.
* st_lsm6dsx
- Ensure we don't set the sensor sensitivity to 0 as it will force
all readings to 0.
- Fix a wait time for the slave i2c controller when the accelerometer
is not enabled.
* stm32-adc
- Precursor for fix. Move a set of register definitions to a header.
- Fix a race when several ADCs are in use with some using interrupts
to control the dataflow and some using DMA.
* vcnl4000
- Fix a garbage of_match_table in which a string was passed instead
of the intended enum.
-----BEGIN PGP SIGNATURE-----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=s9EA
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 5.4 cycle.
* adis16400
- Make sure to free memory on a few failure paths.
* adxl372
- Fix wrong fifo depth
- Fix wrong indexing of data from the fifo.
- Perform a reset at startup to avoid a problem with inconsistent state.
* axp288
- This is a fix for a fix. The original fix made sure we kept the
configuration from some firmwares to preserve a bias current.
Unfortunately it appears the previous behaviour was working around
a buggy firmware by overwriting the wrong value it had. Hence
a regression was seen.
* bmc150
- Fix the centre temperature. This was due to an error in one of the
datasheets.
* hx711
- Fix an issue where a badly timed interrupt could lead to a control
line being high long enough to put the device into a low power state.
* meson_sar_adc
- Fix a case where the irq was enabled before everything it uses was
allocated.
* st_lsm6dsx
- Ensure we don't set the sensor sensitivity to 0 as it will force
all readings to 0.
- Fix a wait time for the slave i2c controller when the accelerometer
is not enabled.
* stm32-adc
- Precursor for fix. Move a set of register definitions to a header.
- Fix a race when several ADCs are in use with some using interrupts
to control the dataflow and some using DMA.
* vcnl4000
- Fix a garbage of_match_table in which a string was passed instead
of the intended enum.
* tag 'iio-fixes-for-5.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: Fix an undefied reference error in noa1305_probe
iio: light: opt3001: fix mutex unlock race
iio: adc: ad799x: fix probe error handling
iio: light: add missing vcnl4040 of_compatible
iio: light: fix vcnl4000 devicetree hooks
iio: imu: st_lsm6dsx: fix waitime for st_lsm6dsx i2c controller
iio: adc: axp288: Override TS pin bias current for some models
iio: imu: adis16400: fix memory leak
iio: imu: adis16400: release allocated memory on failure
iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
iio: adc: stm32-adc: move registers definitions
iio: accel: adxl372: Perform a reset at start up
iio: accel: adxl372: Fix push to buffers lost samples
iio: accel: adxl372: Fix/remove limitation for FIFO samples
iio: adc: hx711: fix bug in sampling of data
iio: fix center temperature of bmc150-accel-core
iio: imu: st_lsm6dsx: forbid 0 sensor sensitivity
iio: adc: meson_saradc: Fix memory allocation order
I hit the following error when compile the kernel.
drivers/iio/light/noa1305.o: In function `noa1305_probe':
noa1305.c:(.text+0x65): undefined reference to `__devm_regmap_init_i2c'
make: *** [vmlinux] Error 1
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When an end-of-conversion interrupt is received after performing a
single-shot reading of the light sensor, the driver was waking up the
result ready queue before checking opt->ok_to_ignore_lock to determine
if it should unlock the mutex. The problem occurred in the case where
the other thread woke up and changed the value of opt->ok_to_ignore_lock
to false prior to the interrupt thread performing its read of the
variable. In this case, the mutex would be unlocked twice.
Signed-off-by: David Frey <dpfrey@gmail.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Fixes: 94a9b7b180 ("iio: light: add support for TI's opt3001 light sensor")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since commit 0f7ddcc1bf ("iio:adc:ad799x: Write default config on probe
and reset alert status on probe") the error path is wrong since it
leaves the vref regulator on. Fix this by disabling both regulators.
Fixes: 0f7ddcc1bf ("iio:adc:ad799x: Write default config on probe and reset alert status on probe")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit 5a441aade5 ("iio: light: vcnl4000 add support for the VCNL4040
proximity and light sensor") added the support for the vcnl4040 but
forgot to add the of_compatible. Fix this by adding it now.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Fixes: 5a441aade5 ("iio: light: vcnl4000 add support for the VCNL4040 proximity and light sensor")
Reviewed-by: Angus Ainslie (Purism) angus@akkea.ca
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since commit ebd457d559 ("iio: light: vcnl4000 add devicetree hooks")
the of_match_table is supported but the data shouldn't be a string.
Instead it shall be one of 'enum vcnl4000_device_ids'. Also the matching
logic for the vcnl4020 was wrong. Since the data retrieve mechanism is
still based on the i2c_device_id no failures did appeared till now.
Fixes: ebd457d559 ("iio: light: vcnl4000 add devicetree hooks")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Angus Ainslie (Purism) angus@akkea.ca
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
i2c controller available in st_lsm6dsx series performs i2c slave
configuration using accel clock as trigger.
st_lsm6dsx_shub_wait_complete routine is used to wait the controller has
carried out the requested configuration. However if the accel sensor is not
enabled we should not use its configured odr to estimate a proper timeout
Fixes: c91c1c844e ("iio: imu: st_lsm6dsx: add i2c embedded controller support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since commit 9bcf15f75c ("iio: adc: axp288: Fix TS-pin handling") we
preserve the bias current set by the firmware at boot. This fixes issues
we were seeing on various models, but it seems our old hardcoded 80ųA bias
current was working around a firmware bug on at least one model laptop.
In order to both have our cake and eat it, this commit adds a dmi based
list of models where we need to override the firmware set bias current and
adds the one model we now know needs this to it: The Lenovo Ideapad 100S
(11 inch version).
Fixes: 9bcf15f75c ("iio: adc: axp288: Fix TS-pin handling")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=203829
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In adis_update_scan_mode_burst, if adis->buffer allocation fails release
the adis->xfer.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In adis_update_scan_mode, if allocation for adis->buffer fails,
previously allocated adis->xfer needs to be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
End of conversion may be handled by using IRQ or DMA. There may be a
race when two conversions complete at the same time on several ADCs.
EOC can be read as 'set' for several ADCs, with:
- an ADC configured to use IRQs. EOCIE bit is set. The handler is normally
called in this case.
- an ADC configured to use DMA. EOCIE bit isn't set. EOC triggers the DMA
request instead. It's then automatically cleared by DMA read. But the
handler gets called due to status bit is temporarily set (IRQ triggered
by the other ADC).
So both EOC status bit in CSR and EOCIE control bit must be checked
before invoking the interrupt handler (e.g. call ISR only for
IRQ-enabled ADCs).
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move STM32 ADC registers definitions to common header.
This is precursor patch to:
- iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
It keeps registers definitions as a whole block, to ease readability and
allow simple access path to EOC bits (readl) in stm32-adc-core driver.
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We need to perform a reset a start up to make sure that the chip is in a
consistent state. This reset also disables all the interrupts which
should only be enabled together with the iio buffer. Not doing this, was
sometimes causing unwanted interrupts to trigger.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
One in two sample sets was lost by multiplying fifo_set_size with
sizeof(u16). Also, the double number of available samples were pushed to
the iio buffers.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, the driver sets the FIFO_SAMPLES register with the number of
sample sets (maximum of 170 for 3 axis data, 256 for 2-axis and 512 for
single axis). However, the FIFO_SAMPLES register should store the number
of samples, regardless of how the FIFO format is configured.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix bug in sampling function hx711_cycle() when interrupt occures while
PD_SCK is high. If PD_SCK is high for at least 60 us power down mode of
the sensor is entered which in turn leads to a wrong measurement.
Switch off interrupts during a PD_SCK high period and move query of DOUT
to the latest point of time which is at the end of PD_SCK low period.
This bug exists in the driver since it's initial addition. The more
interrupts on the system the higher is the probability that it happens.
Fixes: c3b2fdd0ea ("iio: adc: hx711: Add IIO driver for AVIA HX711")
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is a return statement that is indented incorrectly, add in
the missing tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_predisable() should be called last, to detach the
poll func after the devices has been suspended.
This change re-organizes things a bit so that the postenable & predisable
are symmetrical. It also converts the preenable() to a postenable().
Not stable material as there is no known problem with the current
code, it's just not consistent with the form we would like all the
IIO drivers to adopt so as to allow subsystem wide changes.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If a label is defined in the device tree for this device add that
to the device specific attributes. This is useful for userspace to
be able to identify an individual device when multiple identical
chips are present in the system.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The lock is used to protect the buffer during reads. Though the spi
routines have their own locks, it may be the case that the buffer needs to
be protected before it's stored and passed to the IIO read hooks.
indio_dev's mlock was used before.
This change replaces it with the driver's own lock.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The use of indio_dev's mlock is discouraged. The driver already defines
it's own `bus_lock` in `adis16130_spi_read()`, so using the mlock is
redundant.
The parts supported by this chip are obsoleted anyway, so for now we just
remove mlock as part of a general cleanup, until the driver gets removed.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Report iio motion events to iio subsystem and filter motion events.
Wakeup will still be on all channels as it's not possible to do the filtering
in hw.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The interrupt source can come from multiple sources,
fifo and wake interrupts.
Enter interrupt thread to check which interrupt that has fired.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This add ways for the SoC to wake from accelerometer wake events.
In the suspend function we skip disabling the sensor if wakeup-source
and events are activated.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add event channels that controls the creation of motion events.
Tested on ISM330DLC
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This prepares the interrupt to be used for other stuff than
fifo reading + event readings.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Put read magnetometer data by mpu inside the fifo.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support of driving MPU9250 magnetometer connected on i2c
auxiliary bus using the MPU i2c master.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Alexandru Ardelean