Having two or more qdisc_run's contend against each other is bad because
it can induce packet reordering if the packets have to be requeued. It
appears that this is an unintended consequence of relinquinshing the queue
lock while transmitting. That in turn is needed for devices that spend a
lot of time in their transmit routine.
There are no advantages to be had as devices with queues are inherently
single-threaded (the loopback device is not but then it doesn't have a
queue).
Even if you were to add a queue to a parallel virtual device (e.g., bolt
a tbf filter in front of an ipip tunnel device), you would still want to
process the queue in sequence to ensure that the packets are ordered
correctly.
The solution here is to steal a bit from net_device to prevent this.
BTW, as qdisc_restart is no longer used by anyone as a module inside the
kernel (IIRC it used to with netif_wake_queue), I have not exported the
new __qdisc_run function.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various drivers use xmit_lock internally to synchronise with their
transmission routines. They do so without setting xmit_lock_owner.
This is fine as long as netpoll is not in use.
With netpoll it is possible for deadlocks to occur if xmit_lock_owner
isn't set. This is because if a printk occurs while xmit_lock is held
and xmit_lock_owner is not set can cause netpoll to attempt to take
xmit_lock recursively.
While it is possible to resolve this by getting netpoll to use
trylock, it is suboptimal because netpoll's sole objective is to
maximise the chance of getting the printk out on the wire. So
delaying or dropping the message is to be avoided as much as possible.
So the only alternative is to always set xmit_lock_owner. The
following patch does this by introducing the netif_tx_lock family of
functions that take care of setting/unsetting xmit_lock_owner.
I renamed xmit_lock to _xmit_lock to indicate that it should not be
used directly. I didn't provide irq versions of the netif_tx_lock
functions since xmit_lock is meant to be a BH-disabling lock.
This is pretty much a straight text substitution except for a small
bug fix in winbond. It currently uses
netif_stop_queue/spin_unlock_wait to stop transmission. This is
unsafe as an IRQ can potentially wake up the queue. So it is safer to
use netif_tx_disable.
The hamradio bits used spin_lock_irq but it is unnecessary as
xmit_lock must never be taken in an IRQ handler.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a potential jiffy wraparound bug in the transmit watchdog
that is easily avoided by using time_after().
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the old __dev_put macro that is just a hold over from pre 2.6
kernel. And turn dev_hold into an inline instead of a macro.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
# grep -r 'netif_carrier_o[nf]' linux-2.6.12 | wc -l
246
# size vmlinux.org vmlinux.carrier
text data bss dec hex filename
4339634 1054414 259296 5653344 564360 vmlinux.org
4337710 1054414 259296 5651420 563bdc vmlinux.carrier
And this ain't an allyesconfig kernel!
Signed-off-by: David S. Miller <davem@davemloft.net>
qdisc_create_dflt() is missing to destroy the newly allocated
default qdisc if the initialization fails resulting in leaks
of all kinds. The only caller in mainline which may trigger
this bug is sch_tbf.c in tbf_create_dflt_qdisc().
Note: qdisc_create_dflt() doesn't fulfill the official locking
requirements of qdisc_destroy() but since the qdisc could
never be seen by the outside world this doesn't matter
and it can stay as-is until the locking of pkt_sched
is cleaned up.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current call to __qdisc_dequeue_head leads to a branch
misprediction for every loop iteration, the fact that the
most common priority is 2 makes this even worse. This issue
has been brought up by Eric Dumazet <dada1@cosmosbay.com>
but unlike his solution which was to manually unroll the loop,
this approach preserves the possibility to increase the number
of bands at compile time.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds qdisc_alloc() to share code between qdisc_create()
and qdisc_create_dflt(). Hides the qdisc alignment behind
macros and makes use of them.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes the skb trimming code which is not needed since we never
touch the skb upon failure. Removes unnecessary initializers,
and simplifies the code a bit.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
prio2list() returns the relevant sk_buff_head for the
band specified by the priority for a given skb.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to bugs in netem (fixed by later patches), it is possible to get qdisc
qlen to go negative. If this happens the CPU ends up spinning forever
in qdisc_run(). So add a BUG_ON() to trap it.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some network drivers call netif_stop_queue() when detecting loss of
carrier. This leads to packets being queued up at the qdisc level for
an unbound period of time. In order to prevent this effect, the core
networking stack will now cease to queue packets for any device, that
is operationally down (i.e. the queue is flushed and disabled).
Signed-off-by: Tommy S. Christensen <tommy.christensen@tpack.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Herbert Xu